Airport Express not visable with Admin utility, but pingable and...

Can be seen when I search for it in the admin utility. The Airport has started dropping constantly, and sometimes itunes doesnt see it but the device remains 100% pingable at all times.
The green light is on, and its connected fine.
Any reason why windows has issues seeing it (and then itunes fails)
Thanks

I have this exact same problem. It's like something spontaneously just ceased to work inside the AE unit. I don't understand it.
I tried updating the firmware to 6.3 and updated Airport on the G4 to 4.2.1, but nothing has changed. If anything, the problem seems to have gotten worse (sometimes connecting -- > NEVER connecting).
All the forums I have read seem to think this problem has yet to be solved by Apple. They recommend downloading iStumbler or a utility to monitor your networks and keep them "alive" by constantly pinging with a low-level signal. That hasn't worked either.
Need expert advice, please.

Similar Messages

Airport Express not working with WPA

Recently with the newest Macbook Pro airport firmware, my WPA2 network has stopped working so I switched over to WEP, and it started working again. I have a new Airport Express, and I hooked it up to the WEP network and it worked fine.
Just the other day I found out that disabling UPNP can make WPA work again, so I tried it out and my WPA2 network started working again. However, when I reset my Airport Express and tried to hook it up to the WPA2 network it wouldn't work. I could get through the entire setup but when I got to the end, when the Airport Express reset itself, the network would just die, and then I would have to hard reset the Airport Express again.
I'm using a Dlink 624.
I'm really frustrated by all this. I normally don't have any issues, but this latest Macbook Pro firmware seems to have really messed everything up.

I would suggest, reconnecting the Express to the TC again. Use the AirPort Utility to make ALL configuration changes including the network extending settings. Then restart both base stations and check that the settings are still good. Then disconnect the Express and give it a few minutes to initialize. It should connect. If not, then the issue may be either the distance or obstructions (like walls, ceilings, floors, etc.) that is preventing the Express from getting a signal from the TC that is adequate enough to extend.

Airport express not working with apple products

We have been trying to get airport express to work with a macbook pro, ipad2, iphone, laptop, htc wildfire - havent even tried the air music or printer yet!
We have a green light on the airport express which is connected to an ntl cable modem(virgin media network).
Currently the only thing that will connecy is the laptop and my htc phone. All the apple products will not connect?
We went to the apple store today and it worked grand when it was plugged in - the apple products all worked.
The network comes up on ipad2 but when you press connect it says 'unable to connect'
can anyone help us please?
thank you

I have the same issue. Mine fixed itself for a bit and now it's broken again. I'm thinking it's going to be intermittently broken. I've tried turning both devices off and on again but that did not help.

Airport Express (not n) with ethernet hub and as wireless base

Will Airport Express do this?
I've got a cable modem. It connects by ethernet to a hub. Airport Express (not n) connects to the hub by ethernet. My laptops (MacBook and HP 69xx WinXP Pro) connect to AX and internet just fine.
In that same hub, I want to connect a D-Link DNS323, which I wish to be made accessible to the wireless network provided by AX. Here's a sort-of diagram:
cable ethernet
modem ---> hub <--- Airport Express <--- laptops, AppleTV, etc. by wireless
^
|
|
D-Link
DNS 323
Can AX (old style, not n version) use its ethernet connector to both communicate with my cable modem and with other wired ethernet devices through my hub?
Thanks for helping. I tried searching for similar posts, but I failed to find an answer.

With only the hub, the NAS, and the express, you can't access both the internet and the NAS wirelessly at the same time. Here's why:
The AirPort Express has only one Ethernet port. That port can either act as a WAN port or a LAN port, but not both at the same time.
You need the Express to be connected to the internet. Unless you have another wireless router (Apple or otherwise), it will have to be connected through its Ethernet port. Therefore, the Ethernet port must act as a WAN port.
The NAS, on the other hand, is part of your network. For it to be connected, the port must act as a LAN port.
This means that the NAS can't be connected to the Express via Ethernet because then the port would need to act both as a LAN port and a WAN port, which it can't do.
This means you'll need an additional wireless router if you want to access both the internet and the NAS at the same time.
If you have another wireless router (it doesn't have to be an AirPort), I can help you configure it to work with your current network so that you can access the NAS.
Message was edited by: adsfushi72

Airport Express Printer Works with Macbook Pro, but not on Macbook

We have two Macs -- a Macbook Pro, and a Macbook. Both are connected to an Airport Express, and can access the internet and control Airtunes without any issue. However, only the Macbook Pro can print to the Aiport Express connected printer -- a Canon ip3500.
When I go to system preferences to add the printer on the Macbook, the printer is available, and it allows me to add it. However, the location of the printer and the driver( or at least the driver number) are different, even though it is pre-populated by the computer itself.
Once the printer shows as being installed, I can print to that printer, but the job is automatically "Stopped" in the status. I cannot restart the job, it just stalls out.
When the printer is connected via USB, the Macbook can print to it without issue. It can also print to it via bonjour if I share the printer from the Macbook Pro.
Anyone else having similar issues? Any suggestions on how to fix it would be greatly appreciated.

Try creating a new location in the network settings. Then select Network port configurations and drag Airport to the top of the list. Uncheck any unused connection types such as built-in modem and Bluetooth.

Airport express continually diasppears from admin utility

Hi people
I have an apple airport express and airport airport extreme base station
both with the latest firmware patches.
The airport extreme is connected to my optus cable modem and provided internet for my partners wireless laptop and my desktop. My desktop is plugged in via ethernet to extreme base station.
I can start the admin utility and run air tunes for a few minutes then the base station disappears from the admin utility and my connection to air tunes breaks. My connection to the internet remains ok.
If my partner uses her laptop via wireless to serve up airtunes the connection is stable and the basestation does not disappear from her admin utility.
No sure what is going on here, if anything i would have thought that a direct ethernet connection should be more reliable than a wireless connection. This is a very disappointing result as i specifically went the apple kit to ensure that the airtunes express would work with my router...
Any thoughts or is it (as i read other similar posts) completely broken ??
regards
Mark W

I have this exact same problem. It's like something spontaneously just ceased to work inside the AE unit. I don't understand it.
I tried updating the firmware to 6.3 and updated Airport on the G4 to 4.2.1, but nothing has changed. If anything, the problem seems to have gotten worse (sometimes connecting -- > NEVER connecting).
All the forums I have read seem to think this problem has yet to be solved by Apple. They recommend downloading iStumbler or a utility to monitor your networks and keep them "alive" by constantly pinging with a low-level signal. That hasn't worked either.
Need expert advice, please.

Airtunes/airport express not working with MacBook

I have a new Macbook and an older Powerbook. The Powerbook is working nicely with my airport express and airtunes. I copied all settings to the new Macbook and configured it the same way, I also did the firmware update.
ITunes found the airport express, connected and I could listen to the music.
Later during the day it didn't work anymore, although I didn't change any settings. ITunes can no longer connect to the airport express, the airport utility does find the base station, but I can no longer configure or reset it.
I started the old Powerbook again which is still working without problems
What can I do to get the Macbook working as well ?

Same issue here!! Everything working fine with OS X Tiger. As soon as I upgraded to Leopard the problems detecting the AX started. The setup I have is the following:
-Linksys wireless router
-AX connects to wireless network to play songs through iTunes and to print via USB printer.
The green light on the AX is solid which means that it is connecting to the existing wireless network just fine. The problem lies with Leopard detecting and connecting to the AX. I have tried just about everything over the last few days and nothing seems to work. Some resets and updates let my macbook detect the AX for a little while but then it starts to drop and cannot be detected anymore. Apple HAVE to do something about this. These are two apple products not communicating properly. What ever happened to the good old days of apple products being so user friendly and "plug-and-play"
Disgruntled Mac user

Airport Express Not Working with iMac G4 and HP laptop

Ok I am really frustrated with this. I had my Airport Express configured to my mac and my old roommate's mac fine. I moved and just tried setting it up with my mac and my new roommate's PC laptop. It did not work. I tried connecting a router to see if that would help. It still didn't work. I reset the airport's default settings and it still didn't work. Is there a connectivity issue between macs and pcs using the airport express that I don't know about? Am I missing something? Can anyone give me some suggestions of what to try next because I am seriously fed up and running out of ideas of how to alleviate this.
Could it have anything to do with a firewall on the pc or the fact that I'm going from a place that supplied me cable internet to a place that now has dsl?
Thanks for any help.
Aaron

Macs and PCs work together just fine with an Airport Express.
Unfortunately, you have given us little information to help you with beyond simply indicating that "it doesn't work". Please elaborate:
1. do the Mac and PC "see" the Airport Express wireless network?
2. if so, does the Airport Utility (or Airport Admin Utility) on either computer "see" the Airport Express and allow you to view/change its configuration?
3. what does the status light on the Airport Express show?
4. if you can connect to the Airport Express wireless network from the PC and/or Mac, is the only problem that you cannot access the internet?
5. what kind of reset did you do? To really start from scratch, do a factory default reset as described here.

Airport Express not working with wireless router

I just bought Airport Express to play music on my stereo. My PC running XP is connected to my wireless router (TeleWell TW-EA510v3) with ethernet cable and airport express wirelessly. Problem is that Airport Utility (and iTunes) can't find AE if it's not connected to router with ethernet cable.
I can connect to AE from Aiport Utility by "configure other" option so it's connected to my wireless network correctly.
Is this kind of set up even possible (pc wired to router and AE wireless)? I have tried tried WEP, WPA/WPA2 and no encryption on my wireless network and AE connects ok every time but Airport Utility still can't find it. I even tried to make a WDS network but AE was not compatible with my router. Now I can't come up with anything else to try.
Is there anything else to do? Should I buy WLAN adabter to my PC and would AE work then?
Why can't Apple make Airport Utility to recognise AE with given IP like with "configure other" option? Should not be too hard to program?!
Message was edited by: -MTL-

Follow the isntruction lisetd below...they work.
Actually, the ae is a slick device, once you get it to work.
Make sure that one (or both) checkboxes in Airport Utility > Airport Express tab
(middle of page) are not checked...if one or both are checked, they limit (hide) wireless connectivity options (e.g., WEP-64) to choose from.
P.S. You must have patience: it may take a couple of minutes to establish the connection and turn the led to solid green. So, give it a chance.
===============================================================================
OMG!!! You are da man!!!
I have this streaming perfectly now!! Here is what I did for others to see and use (it does work perfectly)
Step 1) Clear/Reset the Airport Express
Step 2) Connect the Airport Express directly to the Router/Modem via Ethernet to set up Wireless
Step 3) Do it via the Manual Set-up Effort Listed Below following:
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing Linksys wireless network>
o Wireless Security: <select the encryption type of the existing wireless network> I have 64bit WEP
(Same as 40bit on the drop down menu)
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)
Once it congratulates you, unplug the ethernet cable
Verify in Aitport Utility that it still recognizes (if not, repeat the above). Note this may take a few minutes, so be patient.
Now place the airport express with your stereo (or whatever) and again be patient as it tries to find the network
(mine took 4 minutes) then it turns green and you are off listening to music on your stereo downstairs in another room.
Frustrating when it does not work at first, but keep trying and it will work!!
Thanks everyone for your help!!
===============================================================================

Airport Express not working with Time Capsule

I replaced a NetGear wireless router with a new Time Capsule. After some trial and error I got everything that was hanging off the NetGear - 2 x TiVo machines, printer, extra ports for business laptops - working except my "old" Airport Express unit that I had been using to send my iTunes to my stereo tuner. I just cannot get this to connect to the Time Capsule wirelessly no matter what I do. It works just fine when connected wirelessly direct to my iMac but just will not connect to the Time Capsule as a client. Any ideas?
Thanks in advance.

I would suggest, reconnecting the Express to the TC again. Use the AirPort Utility to make ALL configuration changes including the network extending settings. Then restart both base stations and check that the settings are still good. Then disconnect the Express and give it a few minutes to initialize. It should connect. If not, then the issue may be either the distance or obstructions (like walls, ceilings, floors, etc.) that is preventing the Express from getting a signal from the TC that is adequate enough to extend.

Airport Express not working with iTunes

After experiencing cutting out and poor sound quality, I reset my Airport Express to factory settings. It is part of of my network with an Airport Extreme. Everything appears to be correctly configured and I get a message indicating it was successful, but then I get an error message after the restarting of the Airport Express and I can no longer see airport Express listed in the Airport Utility window. Playing iTunes through my stereo speakers does not work. In order to attempt the configuration again, I have to reset the Airport Express to see it in the window again. I get the same result each time. Can you suggest anything in the configuration of my Airport Express which would be causing the problem I have an iMac running OS 10.4 Thanks for your help.

I had a similar problem. My solution was NOT to use the Airport Utility application. Make sure you reset your airport express then do the following:
1/ Open Preferences
2/ Choose Network
3/ Highlight Airport and insure it is clicked "ON".
4/ See if it shows up under "Network Name"....if it does click "Apply".
Let me know if u get it working...

Airport Express not working with University Network

So I recently purchased an Airport Express to use as a router/to stream music because my University's (University of Arizona) network is a WPA-2 Enterprise network doesn't allow that. I have an ethernet port in my dorm room and its all hooked up but when I connect to my created network there is no internet connection. I already registered the MAC address with the network so now I'm not sure why its not working.

I have just bought the new Airport Express as well and when I plug it into my router at home it does not pick up the Internet. My old AE has no problems at all and all other connections work.
I can see the new AE in my Airport Utility but cannot connect to it. Really frustrating and far from plug and play.

Airport express not working with optus network

Hi there, the airport express seems not working with my optus network. It is keeping me I cannot access the internet but I do have a wifi signal. Initially I thought there was some problems with Enhernet Wan port on the AE, but after I've done some research I found there might some changes needed to be done with my old router. All I know is im using a NETGEAR router, network type is PPPOE. Also, there were people metioned on the forum that theold modern should be changed to brigdeging mode. I have no idea what is it. Please help. cheers.

Configuration is simple if you start from a factory default condition. Then connect the Airport to AC power and finally to the Internet modem (or modem/router). Open Airport Utility on your Mac or other computer and accept all of the recommendations. After confirming that it works, insert your desired administrative and WiFi passwords.
Do not expect the Airport to respond instantly to the configuration commands. BE PATIENT!

AirPort Express not seen by wifi devices, but router wired devices OK

Hi,
I purchased an AirPort Express yesterday, upgraded the firmware to 7.6.1, connected to my Netgear DG834G router as a wireless client ("Join an existing network"), plugged into stereo and iTunes on my MacPro had no problems using AirPlay.
Today I tried using the AirPort Utility on my iPad and my wife's MacBook (as well as iTunes), but neither of them can see the AX via WiFi. But my MacPro is wired into the router and can see it OK. Likewise if I connect the MacBook to the router it can see the AX fine.
On a more technical note the wired devices can ping the AX, but WiFi devices can't. I find that pretty strange as they're all on the same subnet.
I've tried several resets and reconfigs (even from the MacBook), but once the AX is set to talk to the router then the WiFi devices can't see it. And throughout all this the (wired) MacPro can use AirPlay with no problems.
Has anyone got any ideas on what's going on, I'm a bit stumped! Thanks in advance.
Cheers,
Jay

Problem solved. For some stupid reason I had switched on a setting on the Netgear called "Wireless Isolation", and you can probably guess what that does...
So it's all working now!

Airport Express not working with Comcast

I used to have AT&T and had my airport working well. Yesterday i changed to Comcast and my airport is not working the light stays yellow.. I tried resetting it but it didn't work.. I use it with my old Cisco router and its working. Whats wrong with my Airport Express? My computers are Windows 7

A solid amber light indicates that the AirPort Express has locked up....or it is defective.
Suggest you that try a Factory Default Reset as follows:
Pull the Express from power
Let it rest for a few minutes
Hold in the reset button and keep holding it for another 8-10 seconds while you plug the Express back in to power
Release the reset button after the hold period and allow 40-45 seconds to restart
The Express should display a slow, blinking amber light at this time
If you continue to see a solid amber light after a few tries with a Factory Default Reset, the Express has failed and it will need to be replaced.

Airport Express not visable with Admin utility, but pingable and...

Similar Messages

Maybe you are looking for