Airport Express shows green, no signal.

So after finally moving into my new apartment, I decided to finally go wireless with my iMac G5 and my girlfriend's eMac G4. We practically skipped into the Apple store, purchased an Airport Express card and two airport extreme cards.
And then it all went downhill. I installed the Extreme card into my iMac and it picked up the signal instantly. Well, this was because the Airport Express was leaning against the unit. If I move the Express even one foot away from my Mac, the signal drops completely. There's nothing. The Express still shows "green" but the signal isn't getting to the iMac at all.
Any thoughts?

Most likely problem - when you installed the Airport card into your iMac, you either (a) forgot to attach the internal Airport antenna cable connector to its socket on the Airport card, or (b) you did not FULLY push the connector into its socket, which takes a fair bit of force to do properly.
Review the Airport card installation instructions at:
http://manuals.info.apple.com/en/imacG517inchAirPort.pdf

Similar Messages

  • Airport Express shows green light but NO Internet

    I am using a Macbook Pro and an Airport Express for my Wi-Fi.
    I have recently changed my Internet Service Provider. The new ISP provided me with the following information:
    1.IP address: 172.100.11.17
    2. Subnet mask: 255.255.255.0
    3. Default Gateway:172.100.11.1
    4. Preferred DNS: 172.16.0.1
    5. Alternate DNS: 8.8.8.8
    My ISP told me to enter this information manually unlike my previous ISP who used DHCP.
    I entered this information by going to system preferences >> Network >> Advanced  >> TCP/IP >> Configure IPv4: Using Manually. I also entered the preferred and alternate DNS information under DNS servers in DNS tab.
    I applied these settings and the airport express shows solid green light but gives NO access to internet.
    I have also tried connecting the Ethernet cable directly to the computer, which also shows connected but gives NO access to Internet.
    I borrowed another router from my friend (not apple) and entered the same settings given by my new ISP and boom !!! I got connected to the internet  only through wirelessly BUT no connection again using the ethernet.
    So I am facing the following problem in Mac OS X (10.7.5)
    using
    Airport Express: NO internet
    Ethernet: NO internet
    Other Router(non-apple): Internet works using Wi-fi
    Ethernet: NO internet
    I do not know if something is blocking the connection or what is happening. I have created new locations (under network) and deleted the old existing one's but nothing seems to help. I also did a hard reset of my Airport Express but nothing seems to help.
    Please help me !!!

    I am using a Macbook Pro and an Airport Express for my Wi-Fi.
    I have recently changed my Internet Service Provider. The new ISP provided me with the following information:
    1.IP address: 172.100.11.17
    2. Subnet mask: 255.255.255.0
    3. Default Gateway:172.100.11.1
    4. Preferred DNS: 172.16.0.1
    5. Alternate DNS: 8.8.8.8
    I am able to connect to the internet now directly using ethernet cable but my airport express wouldn't let me connect.
    I must be doing something wrong with entering settings in Airport Express. The ISP technician is as clueless as me and had even did some changes under Wi-Fi in the network section on my macbook pro. I dont know if it is causing these problems. I have a few questions, please help.
    Q1. While entering the ISP provided details using Airport Utility, which of these should I choose: A. Static B. DHCP C. PPPoE ?
    Q2. Should my MAC address in the Airport Utility be set to configure manually or automatically ?
    Q3. What should be my Wi-Fi settings in my computer ?. I mean in system preferences under network, should my TCP/IP set as DHCP or manually ? Under hardware tab, there is an option to select MAC address as either Automatically or Manually. What should it be ?
    Please Help !!!

  • Airport express showing green but no internet connection

    I have a new airport express (2013) connected to a motorola canopy point to multipoint wireless broadband system.
    The express is in bridge mode and is using 8.8.4.4 and 208.67.222.222 as the DNS servers.
    The aiport is showing a green light consistetly. However, the internet connection of devices on the network drops intermittently. Airport utility shows a yellow indicator and "disconnected".
    Sometime the connection reappears quickly. Other times a restart in necessary.
    It does not happen simulatnaesouly for every device. Some can have a connection while others do not. As I write this, my MB Air has an internet connection but my iPhone does not.
    Fixes I have tried:
    Powering down and powering back up begining with the modem and then the base station.
    Changing base station channel
    Turning off wireless printer
    Renewing DHCP lease on base station
    Renewing DHCP lease on individual units
    I see others with this problem but the fixes seem random. I was thinking it is a DNS issue but... the error reads "disconnected" not DNS issue.
    Any ideas?
    Thanks!

    The issues seems to be DNS related.
    When the internetconnection drops, the airport utility indicator switches to yellow, I can still get websites to reslive by using their IP addresses in place of the URL. E.g. http://173.194.70.101 for google.
    But I can make neither heads nor tails of why this happens or when...
    The one thing I think I am noticing but does not make any sense is that when I use the IP instead of the URL, it forces the connection back on.

  • Airport express working for macbook pro but not iphone 5s. Airport utility on the phone shows a blinking orange light. AU on the macbook shows green light.  The airport express shows green light itself.  Anyone know what's going on?

    Airport express working for macbook but not iphone.

    Hello ccoffey1,
    After reviewing your post, I have located an article that can help with Wi-Fi networks. It contains a number of troubleshooting steps and helpful advice for the issue you are experiencing:
    iOS: Troubleshooting Wi-Fi networks and connections - Apple Support
    Thank you for contributing to Apple Support Communities.
    Cheers,
    BobbyD

  • My Airport Express is green, but my computer does not find it on a scan.  I have used it before, but it just stopped working.

    My Airport Express is green, but on a scan, my computer does not find it.  I normally use it to play music from my Itunes to my house stereo speakers, and the icon shows up in itunes.  it stopped working and now my computer does not recognize it.  Help!!!  I hate listening to music on small speakers.

    Hello there Karen,
    It sounds like you are having to power cycle your modem to get internet back every single day. We can start by troubleshooting your Airport Express to help isolate the issue. I would first perform a Soft Reset, then test the issue again. If needed as a last resort I would then perform a Hard Reset:
    Soft reset
    Connect the device to power and wait for it to complete its start up process. To learn more about the start up process, please see All about Wi-Fi base station Status Lights (LED).
    Press and hold the reset button with a pen, pencil, or straightened paperclip for 1 full second, then release it. The light (LED) will begin flashing amber, indicating that the device is in soft reset mode.
    From the AirPort menu bar item, choose the network created by the device (the network name does not change).
    Open AirPort Utility from Applications > Utilities.
    Select the base station, then click Edit (The Edit window will indicate that the base station is in Soft Reset mode).
    Move through the tabs to make changes to your passwords or other settings as needed, and click Update and Continue as required
    Quit AirPort Utility.
    Hard reset
    Press and hold the reset button with a pen, pencil, or straightened paperclip until you see the status light (LED) start to flash amber rapidly, which should occur after about five seconds.
    Release the button and the device will reset.
    Wait about a minute for the base station to finish restarting, then open AirPort Utility from Applications > Utilities.
    Select the base station from Other Wi-Fi Devices, then click Edit.
    Select the Other Options button.
    Select "Restore previous settings" and click Next until you get to the final window.
    AirPort Utility will indicate that Setup is complete. Click Done.
    Quit AirPort Utility.
    Resetting an AirPort base station FAQ
    http://support.apple.com/kb/ht3728
    Thank you for using Apple Support Communities.
    Cheers,
    Sterling

  • Airport Express shows constant amber

    My Airport Express shows a constant amber. As soon as I plug it in it show's green for about a second and then moves to a solid amber, there's no flashing and it doesn't appear to be searching.
    I've tried all the reset options including the factory default where you keep the reset button pressed while you plug it in but all I get is the Amber.
    Am I doing something wrong? It is dead??

    Temporarily connect your Mac via Ethernet directly to the AX. Then you can configure the AX. You may also need to do a hard reset of the AX.
    Shouldn't the AX start flashing amber as soon as it's turned on as it's searching for a computer?
    The flashing amber indicates the AX hasn't found an Internet connection. It has nothing to do with connecting to any computers.

  • Will Airport Express boost a weak signal?

    I get wireless coverage everywhere in my home, but in some areas the signal is less strong than others. Will an Airport Express boost the signal so that the 'weak' areas will have the same signal strength as the 'strong' areas?

    If you are 20 feet from the router and only show a couple of "bars", either your router is not performing up to specifications or you have some wireless interference issues at your location.
    An AirPort Express can extend the signal "deeper" but it won't make it stronger. It can only extend what it receives.
    I suggest that you investigate your low signal strength issue before adding an AirPort Express. BTW, I assume that you are aware that the Express can only "extend" a signal from another Apple "n" router. It won't work with the products of other manufacturers for that purpose.

  • Airport express shows in Sys Pref but cannot select it

    My Airport Express shows in bold as a devise in System Preferences > Sounds> Output, but when I click on it, it will not select, going back to highlight internal speakers.
    I can select my Airport Express in iTunes, and it works but I cannot output sound to it in other programs, ie podcasts, online videos, DVDs. I could do this before I upgraded to Mtn Lion.
    Running OS X 10.8.2, MacBook Pro 2.53 GHz Intel Core 2 Duo, 4 GB memory.
    Thanks,
    3pin

    AirPort Utility for the iPhone, iPad, etc does not support the older version of the AirPort Express that you have.
    Try installing AirPort Utility on the Lenovo laptop to see if you can configure the AirPort Express that way.
    If the laptop runs XP SP3 or Vista SP2.....use AirPort Utility 5.5.3 for Windows - Support - Apple
    Windows 7....use AirPort Utility 5.6.1 for Windows 7 - Support - Apple
    Remember that the SB5101 modem must be fully reset before it will associate correctly with the AirPort Express. That means pressing the reset button on the back of the modem (if present) and powering off the modem for at least 30 minutes, then connecting it to the AirPort.

  • How many airport express can I add to my network for the purpose of using the airport express to send audio signal to different rooms in the house? I'm interested I'm running about six different zones.

    How many airport express can I add to my network for the purpose of using the airport express to send audio signal to different rooms in the house? I'm interested I'm running about six different zones.
    What I'm looking to do is to have self powered in ceiling speakers in every room in my house with out having to run wires to every room to carry the audio signal. I would like to use the airport express to do the job of carting the audio signal.
    Here's my set up now I have an airport extreme and one airport express that I use to carry audio to one room.

    FWIW. I have used up to four AirPort Express Base Stations (AX) for streaming sucessfully in pretty much the way you have described. I didn't have a need to try more so I can't attest that more would or would not work.

  • Airport Express has very weak signal even to the next room

    I am wondering why my airport express has a weak signal. The signal to the next room(about 4 or 5 meters away), is so weak that you can only see one or 2 lines from the graphic at the internet connect. My base station has the last firmware from apple. Has anybody else experiencing this problem or knows what could be wrong?
    Mac mini G4 1.25, iMac G5 2.0, MacBook 2.0, iPod 20Gb, iPod nano 4Gb, iPod 30Gb   Mac OS X (10.4.7)  

    I have tried changing channels, I have tried using interference robustness but nothing seems to work. Isn't it so wierd thought that in the same room within 1 meter distance, the signal becomes from strong to weak, to zero?? The funny part also is that when i change channel for a few seconds the signal is very strong until it drops to zero. When i try another wireless device doesn't seem to have this problem but only with airport express base.

  • My wifi is not too strong in one room, can I use an Airport Express to boost the signal?

    I have an Airport Base Station but the signal is only one or two bars at one end of my house. Can I use an Airport Express to boost the signal?
    Also the AE I have is an older model and I can't get Mountain Lion to talk to it. How can I get around this?

    Also the AE I have is an older model and I can't get Mountain Lion to talk to it. How can I get around this?
    You might want to look over this article:
    http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html

  • My new Airport express mysteriously dropped all signals, I reset it and only my iMac is now connected to my network. My iPad, iPhone 4S and Roku box will not connect - any solutions to this?

    My new Airport express mysteriously dropped all signals (due to lack of DNS settings ?!?!), I reset it and only my iMac is able to be connected to my network. My iPad 2, iPhone 4S and Roku box will no longer connect. Any solutions to this? Everything was using my netwoek before.

    Did you power down your modem prior to resetting the Express?
    If not, do it now. Leave it connected to your Express while you power it down. Let it rest a moment or two, then power it back up. Once it restarts, determine if all your other devices are able to connect.

  • Can airport express output a digital signal to feed a separate audio DAC?

    Can airport express output a digital signal to feed a separate audio DAC?

    Yes. To access the digital output from the AirPort Express Base Station's (AX) audio port, you will need to connect a mini-TOSlink digital optical cable.

  • HT2421 airport express sign green light after 2 5  minot it turn off

    airport express sign green light after 2 or 5  minot it turn off automaticaly

    I've solved this by resetting my wireless internet connection at the box and then setting up airport express again.
    I don't know whether that will help you.....

  • Airport express is green - but not showing up in AirportUtility or AirTunes

    Hello everyone
    I have an Airport Extreme as my main base station upstairs. I have recently plugged in a Dlink615 using an ethernet cable to give me wireless signal in over my kitchen downstairs. This has worked well and we can all use our laptops etc. in the Kitchen now.
    However - I have an Airport Express plugged in - in the kitchen, and have configured it to join the wireless network being pumped out by the Dlink - all seems to be well - the Airport Express appears to connect fine and go green - but following this, the Airport Express can not be found by the Airport Utility and does not show up in AirTunes.
    Can any one offer any advice?
    Thanks very much.

    Hi Carolyn
    Thanks for your reply. I'm running 10.6.4.
    Unfortunately - no luck with that solution. The Kitchen Airport Express also does not show up in the air tunes on my Apple TV.
    I have had no problems with getting airport expresses to show up in air tunes before adding this Dlink to my set up - I think it is something to do with the fact that the DLink is plugged into my Airport extreme. (I have tried DHCP off and on).
    Thanks

Maybe you are looking for

  • Connecting computer to tv for viewing EPIX,ETC.. but not through router?????

    I need to start connecting computer to tv for viewing EPIX,ETC.. but not through router?????  I have a workroom with a TV but without cable connection, so I thought I would connect my computer to my TV.  I have an Acer Aspire laptop. and a 27" tv.  P

  • Lost work

    I was working on multiple art boards. Illustrator asked me if I wanted to revert. I accidentally hit okay, and all of my artboards disapeared. I tried doing undo, but nothing happened. How do I undo this? I need that work back.

  • Only year not full date in ABAP HR

    i need only year to be selected by the user on selection screen. do anyone know any function which only gives year .

  • Remove various accepted domains (exchange 2007) from a list file via powershell

    hello! i'm a newbie with powershell and i'm trying to find if is it possible to remove a lot of exchange 2007 accepted domains from a csv file using powershell. I want to delete accepted domains contained in a csv, it has only domains name and powers

  • Speeding Up The Loading Time of Plug-Ins.....

    Hi. I have Scarbee Vintage Keyboard Collection and it takes about 1/2 mins to load the engine, then 2/3 mins to load a patch. It doesnt do this with other plugins and my computer is certainly not slow. Has anyone got any ideas of what this could be?