Airport Express shut off after VPN connection (Win XP)

Hi all,
I bought an Airport Express (AE) the other day to stream iTunes tracks to me distant speakers. I am using a laptop, Windows XP, SP 2. I all works brilliantly.
However, the moment I am connecting through VPN (Cisco Client) to my university, AE is no longer recognized.
The VPN is configurated that it only allows IPsec / UDP. Ports cannot be added. It runs on port 1000.
Is there anything I can do to make the AE reappear during a VPN-session? I need to be connected via VPN most of the time.
I would greatly appreciate your input!!
Thanks!
Til

By default, the security appliance allows IPsec packets to bypass interface access control lists (ACLs). In order to allow specific traffic for a VPN tunnel, apply interface access lists. Complete these steps (apart from the basic VPN configuration) on the PIX/ASA:
1. Use the no form of these commands in order to disable sysopt connection permit-ipsec on PIX version 6.3 and sysopt connection permit-VPN on PIX/ASA version 7.x.
2. Create an access-list for traffic that goes into the outside interfaces. Refer to this access-list example in order to allow only Telnet traffic:
access-list outside_in extended permit tcp 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 eq 23
3. Create an access group and bind it to the outside interface. For example:
access-group outside_in in interface outside

Similar Messages

  • Airport express shuts down after december update firmware

    can anyone advise me on AEXpress which shuts down very soon after powering up, all since i upgraded firmware earlier in december? this is a replacement model which i got new in summer 2010...out of warranty now. it was fine on XP as client mode connecting wirelessly to Linksys WRT160N router; since upgrade, the airport express shows green light for 2 seconds; then amber for 1 minute; then no light at all. sometimes i plug it in and no lights appear at all. i doubt it's hardware as it followed the software update immediately. Should I somehow try to reinstall the previous software? but don't know how to do that since it won't stay powered on and doesn't show on airport utility. thanks, pdoyle

    Your best option is going to be to try to perform a Factory Default Reset on the AirPort Express to see if that will clear up the difficulties. If this is successful, you could rollback the firmware to an earlier version or reconfigure the device again with the current version of firmware.
    o Power down the Express for at least 20 minutes
    o Hold in the reset button and keep holding the reset button in as you plug the Express back in to power
    o Keep holding the reset button until you see the amber light blink more quickly. Hold another 3-4 seconds when you see this and release the reset button.
    With luck, the Express has now been returned to default settings so you can try to reconfigure it again.
    If you try the Factory Default Reset a few times and the Express is still having difficulties, I'm afraid there's been an internal failure within the device and it will need to be replaced.

  • Ipad2 shut off after down the battery but when connect the charger my ipad2 is not storing the power in the battery and i also not finding the error code ???

    ipad2 shut off after down the battery but when i connect the charger with my ipad2,  its not storing the power in the battery and i also not finding the error code ???

    If you drained the battery, it may take a bit for it to come back. I'd plug it in and leave it for a few hours and see if it's charging.
    If not, you can try to do a reset. Hold down the sleep and home keys for about 20 seconds. When you see the white apple, let go and let it reset and see if it charges.
    It's also possible that your battery has reached the end of its life. THey can only handle a finite amount of recharge cycles. If you can't get it to hold a charge, then make an appointment at your local apple store and explore your other options.

  • TS1589 I have to reboot my BTinfinity router to enable me to link my ipod to Airport express. When it is connected it works perfectly, but it is getting a bind to have to keep switching the router power off. Any one help???

    I have to reboot my BTinfinity router to enable me to link my ipod or my iphone to Airport express. When it is connected it works perfectly, I use it to play music through my BOSE soundwave, but it is getting a bind to have to keep switching the router power off. Any one help???
    Ipod touch: 4th generation Upto date software
    Airport Express: Latest model
    Iphone 5: Upto date software

    This can sometimes be the result of a faulty/damaaged USB sync cable.  Do you have another cable you could test it out with?
    B-rock

  • After 15 mins  with no activity my airport express turns off how can I make it permanent

    After about 15 mins with no activity my airport express turns off. How can I make it stay on permanently ?

    Not sure what you mean by "turns off".  Are you saying that the light on the Express goes out after 15 minutes?
    Assuming that it is functioning correctly, the AirPort Express is "always on". It has no type of "sleep" setting.
    If the power light on the Express remains on, you have some other device on the network that is going into a standby mode or sleep mode. Check the Preference settings on other devices on the network.

  • Airport Randomly Shuts-Off; Reboot Will Temporarily Solve The Problem

    Ever since I've bought my Mac (July 2010) I've been having trouble with the Airport. I'll be browsing the net and all of a sudden my pages won't load, it just stops. The Airport icon in the menubar shows full signal, but when I go into System Preferences it says that my Airport if "Off." When I click the button to turn it on it acts like a dummy button, it just doesn't do anything. I can click it twenty-times and my Airport will still be off.
    I doubt this is a router problem as I have tried this with various routers at various places. I took it into the local library, a hotel, a local gas station that has Wi-Fi and it continues to happens. Not to mention that the Airport itself shuts off. This really ***** when you're in the middle of a 1GB update and it just stops...then you have to start over.
    After I do a complete reboot the Airport is on again, well most of the time. Sometimes it just stays off and I reboot it again. Sometimes it stays on for three-days and sometimes it stays on for five-minutes and I have to reboot six times or so until it stays on for a while. The average is about 30minutes until it shuts down again.
    I've tried reinstalling my operating system, delete preference files, deleting my Airport connection and then recreating it, updating my Mac, trying different firewall settings, I tried booting in 64bit mode. Nothing seems to work. I tried an Apple Hardware test two times. One time I just did it and it reported no problems. The second time I waited until it shut down but it reported nothing, although I think it's because I rebooted and the Airport was "fixed" and it detected nothing.
    I thought this was just something temporarily when I got my Mac so I waited and didn't call support. After 8months I decided to call support and they want $50 to try to diagnose it for me, which isn't fair because it happened from day one and I just thought an update or something would fix it. Not to mention, that a Genius Bar will look at it for free (two hours away from the closest one). Any hints, ideas, or tips? Thanks.

    Sorry for bringing this ancient thread back to life.
    Back when I originally posted this, I did take your advice. I drove 2.5hours to the nearest Apple store and left it overnight for them to do diagnostics. They could find nothing (or so they claimed) and have me drive back up the next day to get it.
    Ever since I've been dealing with the issue. Finally I broke down and bought a new Airport card and antenna. It worked about a day and then the same issue appeared again.
    I'm now on 10.8.2 with 8GB of RAM and an SSD – still the same laptop though.

  • Can't find Airport Express via wireless or wired connection.

    I've run across this topic in this forum and a lot of others and nothing I've found has helped resolve the issue. It seems like the one definitive answer I found was to return it to the store, but I'm hoping to avoid that so I figured I'd try once more.
    Running Windows XP and using a linksys Wireless-G network card. When I first got the Airport Express I was able to connect to it but then I had some issues with my cable network connection and had to reset everything. Since then I haven't been able to connect to it, and currently I can't find it using the Base Station. Tried resetting it to factory defaults about 10x and I'm still stuck on blinking yellow. I tried connecting it directly with a network cable and even then my computer can't seem to find it.
    I tried turning off my firewall, reinstalling the Airport Utility, connecting to the IP address 10.0.1.1 using the "Configure Other..." box and no luck.
    Any suggestions?
    Thanks much.

    The issue is within the network configuration of the Airport Express. As you mentioned, all hardwired devices can use AirPlay but all wireless devices can't.
    Normally, the Airport Express will wirelessly join your existing network, and Airplay will work with all devices. Any reason why you have your Airport Express connected to your router via ethernet?

  • IPad Personal Hotspot antenna shuts off after a few minutes of non-use. This happens in both Verizon 3G and LTE areas. Turning off LTE does not help. Turning Personal Hotspot off and then on works. Does this happen on Mini and Retina?

    iPad--third generation shuts off antenna/hotspot after a few minutes of non-use.
    Happens in 3G and LTE VZ environment.
    Turning hotspot off and on getsw things working again.
    Does Apple have antenna on a timer so it shuts off after a few minutes?
    Does this happen on Mini and Retina as well?
    FLAGSTAFFLAR

    Fixed!
    Two things together have restored connectivity.
    1.  I changed the name under Settings > General > About > Name from My Name's iPad to iPad of My Name.  I read somewhere that iOS 7.0.1 or 7.0.2 (I forget which) sometimes had issues with apostrophes here.  Easy enough to test.
    2.  I then reset (again) the APN settings under Settings > Cellular Data > APN Settings > Personal Hotspot and reentered our provider's info (APN, Username, Password) there.
    I don't know WHY it worked, but the personal hotspot is now happily sharing (again) internet connectivity with my MacBook Pro.

  • Iphone 3g shuts off after the apple loading screen then cuts back on

    Iphone 3g shuts off after the apple loading screen then cuts back on by its self but when i connect it to a charger it works fine also my on/off button is unresponsive (i havent dropped it or wet it so im confused why its doing this)

    Welcome to the discussions,
    normally you could try to reset the phone by holding the sleep and home button until the Apple logo comes back. But since the sleep button is unresponsive, try to restore "as new iPhone", if necessary without using the backup afterwards, in case the backup contains corrupt data.
    Restoring: http://support.apple.com/kb/HT1414

  • HP DV6-6B25TX shutting off after 10 to 15 seconds irrespective of battery power or AC power

    Hi,
    MY DV6-6B25TX is shutting off after 10 to 15 seconds irrespective of battery power or AC power.
    Following is the complete scenario of what happened during the last few weeks:-
    Two weeks back i was using the laptop with the AC adaptor plugged in for charging, the battery got charged upto 99% then it stopped charging and the battery icon text displayed, 'Plugged in, Not Charging'.
    A week back the battery was 20 %, after plugging in the charger, still the same message 'Plugged in, Not Charging'.
    Now the laptop doesnt respond to the power key when the battery is inserted.
    If i remove the battery and again put it back, it starts without pushing the power button and shuts off after 10 seconds, i.e. even before starting Windows.
    It shuts down even when on Bios Screen, so OS is definately not the issue.
    When i connect the charger and press the power button, same thing i.e. starts and shutts off after 10 to 15 seconds irrespective of BIOS screen or Windows Boot.
    I removed the ram and but it back again but still the problem persists.
    Also there is no question of overheating due to dust as i have barely used the laptop for a few hours, the laptop is around 6 months old and under warranty.
    Please Advice ASAP.
    Thanks in Advance.
    This question was solved.
    View Solution.

    Honestly, something is preventing the battery from being charged. The notebook shutting down seconds after reinserting the battery is a good indication the battery just isn't getting charged. This could be a failed battery, charger, charging port, or motherboard in rare instances.
    Since it is in warranty, I recommend contacting HP support as there is no easy fix for this on the forums. It is a hardware issue.
    The number for support in the U.S.A. and Canada is 1-800-474-6836.
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • Airport express second generation do not connect to the internet

    Airport express second generation do not connect to the internet. I changed my location and the problem happened . Earlier it was running smoothly. I am not finding the cause of the problem. I switched on and off several times but the problem persists. Please help me.

    Are you asking the make/model of the computer or the AX base station?
    Neither, I was interested in the make/model of the cable modem.
    Our ethernet connection was fried in an electrical storm so we had to go wireless.
    Electrical storms are never a good thing when it comes to electronics. What was/is your current network configuration? Is it something like the following?
    Cable modem > (Ethernet cable) > AX > (wireless) > wireless devices
    Is there another router, other than the AX, in the configuration? ... or an Ethernet switch? I'm just trying to understand your network to best advise you on how to configure the AX.

  • My iPad does not automatically shut off after several minutes of non use. I can shut it off with the on/off switch. What can I do to get the auto sut off feature back?

    My IPad does not automatically shut off after several minutes of non use as it had been doing a few days ago  How can I restore this auto feature?

    Settings>General>Auto-Lock and select an Auto-Lock time (the "Never" setting will of course never auto-lock the device)

  • I have a Ipod shuffle 4th generation. I would like for the music to shut off after one hour long song automatically rather than go to the next song. Is this possible?

    I have an ipod shuffle 4th generation. I would like for the music to automatically shut off after one hour long song rather than going to next song on the list. Is this possible?

    Sorry, but it's not.  The only way to get this to work is to only put the one hour song on your Shuffle. 
    B-rock

  • Final Cut Pro Randomly Shutting off after Minutes

    Every time I open FCPX and begin editing it randomly shuts off after about 3-4 minutes. Regardless of what I am doing. I get no wheel or anything, it just shuts off clean. I am running the most recent update to Lion, FCPX 10.1 with 8GB of ram... this is really frustrating. Any thoughts?

    #44: FCP acting weird - Trash Prefs
    Shane's Stock Answer #44: FCP acting weird or unusual. Just not like is normally should
    If the program was working fine, and now isn't, or just isn't working the way it should, the first things to do are:
    1) Trash your FCP preferences. Download the appropriate version of FCP Rescue at http://www.fcprescue.com and run it.
    http://www.kenstone.net/fcphomepage/trashing_fcpprefs.html
    2) Open the Disk Utility and Repair Permissions.
    3) Shut down for 10 min. Go for a quick walk around the block and get SOME exercise today. Come back, turn on the computer and see how things are.
    4) (optional) Do the Hokey Pokey and turn your self about. Results may vary.
    Shane

  • Can't configure airport express with laptop after 10.5.6 update

    I can't configure airport express with laptop after 10.5.6 update
    the airport express is seen but can't access configuration screen, I get the spinning wheel forever.
    Other computer gets to the configuration screen without problem.
    And the airport utility describes the airport express like this: syAP.802.11format

    I downloaded the airport utility and re-installed
    and the problem was solved

Maybe you are looking for

  • After upgrading to OS X Mavericks now I can't print, any idea what I should do?

    i just upgraded my system to OS X Marvericks and now I can not print through our office network printer. Office printer is a Canon Image Runner Advance C5030 (Colored). Anybody have any idea what to do? Need help.

  • Where is search in the forums

    I have looked on forum pages on how to search a topic. For the life of me I can not find it. The only one I see is at the very top, which takes me out of forums.

  • Calling xRPM standard iView from custom WD ABAP iView

    Hi, We have an issue regarding - calling xRPM standard iView from WD ABAP Application. Here are the details. When xRPM 4.0 application is displayed by clicking the Portfolio Management role, the item dashboard gets displayed. On the leftside, tabs fo

  • How to add JDBC Driver to my CLASSPATH

    Hi~ I use MySQL JDBC Driver in my program like that Class.forName("com.mysql.jdbc.Driver");But when I try to run it, I got a ClassNoFound Exception,I hava add mysql-connector-java-5.0.3-bin.jar into my CLASSPATH, but it no use.How to fix it ? Thanks

  • Corrupt LR Catalog!(?)

    I´ve got 133.300 picture on a 2 TB HD. The catalog is on my laptop. Some of my pictures are only to be seen in the Library mode. When I go to Developent mode I´m told, that "The folder could not be found" The píctures are counted in the keyword list.