Airport Express Speaker output very quiet with 60-cycle hum

I've previously hooked up my Airport Express to my stereo system via AirTunes, and it worked fine. But I just moved and set up my home network with my Airport Express connected to the stereo with the mini-stereo adapter. But now, when I play music over AirTunes, I can hear the music very faintly, but it's about the same volume as a 60-cycle electrical interference hum, and definitely not listenable. So I know the music is streaming and the AirPort is receiving, but I'm wondering if it's an electrical problem with the AirPort or output jack, or is there some software or hardware fit I can do myself. I've plugged in & out the cord, it works with an iPod, it's connected to a non-Phono jack of the stereo (AUX port), and I've reset the AirPort Express unit. Any other suggestions? Thanks in advance.

Hello AOSmith. Welcome to the Apple Discussions!
To rule out your stereo or audio cable, try substituting a pair of stereo headphones plugged directly into the AX's audio port. Do you still hear the hum? If so, then the problem is either with the AX itself or the power source is not properly shielded. Try connecting the AX to a known good power strip; one that has surge protection and/or noise cancelling capability would be ideal, and then, plug this into the outlet that you had the AXn connected to. Did this help? If not, then unfortunately, the problem may be with either the AX's audio and/or power circuit.

Similar Messages

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Hello Cloud19,
The article linked below provides some helpful information and troubleshooting that can help resolve issues with AirPlay and your Airport Express.
iTunes: Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS5209
Cheers,
Allen

Cannot configure and connect to Airport Express Base Station Model A1264 with Windows 7 (x64)

I am not able to connect Airport Express Base Station Model A1264 with Windows 7 (x64). I did a factory reset, uninstalled and reinstalled the AirPort Utility for Windows v. 5.6.1.
My objective is to extend a non-Apple WiFi network with Airport Express Base Station Model A1264 and use it for direct ethernet and/ or wireless connection. Any guidance as to how I can get set up here?

This is very common, we run a mix of mac and various pc brand desktops and laptops, what I have found is that using the windows wireless client rather than manufacturers on some laptops helps, getting the latest wireless drivers from the manufacturer has helped, make sure all your windows updates XP and Vista are current.
If all the above is covered try the different WEP WPA WPA2 variants or even without for test purposes. I have most success with WPA2.
Finally I am assuming your running the latest firmware on the express unit, whilst this hasn't attributed to better connectivity for us I did it regardless.
Message was edited by: Fence Rider

Is AirPort Express v.6.3 compatible with OS X 10.8.2?

Is AirPort Express v.6.3 compatible with OS X 10.8.2?

What computer are you using?
Does your computer meet the minimum standards for running Color? (Link to standards)
Does it have dual monitors? (It should and each should be at least 1650x1050)
What is the format of the material? (It should be ProRes.)
And so on.
And yes, it does run in ML, though I don't trust it in that environment. I run it under 10.6.8 on a MacPro with a Kona card to feed the external reference monitor.
x

HT1515 How do i get my old AirPort Express (7years old) to work with my new Time Capsule?

How do i get my old AirPort Express (7years old) to work with my new Time Capsule?

Does anyone at Apple have help for this sort of question - I too have an old printer (HP LaserJet 5MP) that I would like to keep using on my Mac. (Mac OSX 10.6.8).
I got it working by getting a USB cord that connects to it - but every once in a while it just stops working for weeks. The mac 'sees' it and it sends the data because the printer lights start blinking but then it just doesn't do anything. Is there no one who can tell me (and raterada) how to get some new life into these old printers. I would rather not add this (and a new toner cart) to the landfill just yet. . .

Someone gave me a airport express router. it works great with my macbook but when i try to connect to my iphone it says it can't be set up by "this software". Where can I download whatever software my iphone needs so I can get wifi?

Someone gave me a airport express router. it works great with my macbook but when i try to connect via wifi to my iphone it says it can't be set up by "this software". Where can I download whatever software my iphone needs so I can get wifi?

Per chance is your AirPort Express Base Station (AX) an 802.11g model? If so, that is why you are getting this error message from the AirPort Utility running on the iPad. You would need to use either version 5.6 or 5.6.1 running on a Mac or a PC to administer this base station.

HT201343 Apple Tv mirror + Airport Express audio output = How to?

I want to mirror my MacBook to the Apple Tv but I want to send the audio to the Airport Express.
If I ask my Apple Tv to send the output to the Airport, it works just fine.
If, after that, I use the iPhone to mirror the screen and watch some video on youtube or Twitch, it works fine either.
But if I use my MacBook Pro to mirror the screen, the audio output is sent to my TV through the HDMI cord.
Is that any way that I can solve this?
What I want to do is just mirror my MacBook screen with the audio coming out through the Airport Speaker.
Thanks for any help, folks!

Hi wennberginho!
I have a couple of articles that should be able to help you with this issue. If you have a 1st generation Apple TV, you will want to reference this article:
Apple TV: Using AirTunes
http://support.apple.com/kb/HT3291
However, if you are using a 2nd or 3rd generation Apple TV, you will want to reference this article:
Apple TV (2nd and 3rd generation): Understanding AirPlay settings
http://support.apple.com/kb/ht5517
Hope this helps. Thanks for using the Apple Support Communities!
Cheers,
Braden

Airport Express speaker problem

I have an Airport Extreme running my home network with two Airport Expresses, both hooked up to powered speakers. One Express is the older model, the other brand new. AirTunes intermittently drops one or the other speaker setup. My question is this- would I potentially fix this problem by upgrading the older Express to a new one? Thanks!

My question is this- would I potentially fix this problem by upgrading the older Express to a new one?
If all of your wireless client support 802.11n, then the answer would be yes. In that case you could create an 802.11n only network to get the best bandwidth possible for streaming.

Airport Extreme + airport express - problem outputting to multiple speakers

Hello,
I have set up my airport express by joining my existing Airport Extreme base station wireless network. When I play my music in iTunes, I am able to select either the Computer or Airtunes for the output in the drop down box in the lower right of iTunes. When I select Airtunes, the music streams no problem to my remote speakers connected to Airport Express. However, when I try to select Multiple Speakers in the drop down menu in iTunes, a pop up Remote Speakers box opens - when I select both the Computer and Airtunes in this box, I get an error message - "An errror occurred while connecting to the remote speaker "Airtunes". An unknown error occurred (-3256)." Since the error occurs only when I try to selct both the computer internal speakers and the remote speakers, but I am able to connect to the remote speakers by themselves, I am really confused. Any thoughts?
Charly

Just to clarify, the goal is to play iTunes on both the computer's internal speakers and my remote speakers at the same time.
Charly

Airport Express + iTunes 10 not working with Airtunes, but 2nd Airport does

Hey,
at first I have to excuse myself for my English, i come from Germany.
I looked around in the topics but i didn't find anything that helped me.
I own 2 Airport Express stations since nearly a year.
One of it creates a Wi-Fi network and is connected to a switch, which is connected to the internet.
The other Airport Express is set up as repeater and everything works fine, even Airtunes.
But then i noticed, that the Wi-Fi creating one was not able to work with Airtunes, which it was some weeks ago. I think this has something to do with iTunes 10. The other Airport works well with Airtunes with the same Macbook and speakers.
So I made a new set up on the Wi-Fi Airport, because some guys reported, that the problem would disappear then, but it didn't.
But I wondered why my iPhone 4 is now abled to play music via Airtunes with the new iOS 4.2.1 on the "broken" Airport, because my mac was not abled to do so and I thought of returning it to the Apple Store.
So how do i get this thing running again? I would like to use both of the Airports to listen to music in different rooms with my Macbook.
I would be glad for any help, thanks in advance
TheShima

@TheShima,
First open up the airport utility and see if both AE's show up. If not:
This would be my guess, unplug them both for 10 seconds, plug the network creating one back into the wall, them plug the second one back in after the first has a green light. If that doesn't work, "manual setup" and looking for the option that allows speaker sharing.
Finally if that doesn't work reset them, recreate the network reviewing the the advanced settings in "manual setup" and looking for the option that allows speaker sharing.
Does anyone know how to get movie audio to play through the airport express? I really want this to exist my wife's laptop speakers are awful and I would love to have the audio streamed to my airport express.

Airport Express not working when used with Broadband Router **HELP!!!**

Hello.
I have an ethernet network in my house, and I am connected to the network via a Linksys router for Broadband VOIP and internet. I am on a G5 in my home office and want to stream music to my Airport Express for my home stereo in the living room, via the ethernet connection.
The problem is that when using the router in my network, only the Admin Utility sees the base station-- iTunes does not.
If I remove the router from the equation altogether and plug the network ethernet cable directly into the G5, the AX in the other room works just fine and I can get internet on the G5 in the office. The problem is that I need the router to operate my Vonage VOIP phone service and to connect a second computer to the internet as well. The IP address for the router in the home office is "192.168.x.xxx" and when I try moving it to the living room and connecting the AX to it, the Admin Asst doesn't see the AX at all.
When I connect the router to the network in the office, I can use internet on both computers and the VOIP phone service, and the AX Admin Asst. sees the base station from the other room. But again, iTunes does not.
Is there a way to configure the router to see the AX?
Thanks for your help!

Forgive me if this a little off thread, but I have just managed to get this to work and thought it might help people with similar configuration issues (mix manufacturer wireless networks)
I received an Airport Express (FW v. 6.3) for Christmas this year. I already am using a D-Link DI-524 wireless(G) router (Rev A FW 1.03) for my Comcast cable modem in my house (downstairs). What I wanted to do is to add the Airport Express in my office upstairs to my network (client mode) so that I could print from my HP Deskjet 3740 printer and listen to iTunes on my stereo through Airtunes. I have two iBooks (G3) with regular (802.11b) airport cards in them) running Tiger.
I ran into a couple of snags though. I could see the printer in Rendezvou and I could see the airport express in iTunes. I however could not print to the printer or connect to the speakers. I was able to connect to the speakers very intermittenly and then the audio would be disrupted every few seconds.
After a bit of hacking, what I found is that it seems that WPA PSK security doesn't work between the two. I changed the security to 128 bit WEP (ASCII mode). This means that you need an exactly 13 character pass phrase. This is necessary because Apple (and pretty much only Apple) supports 40 bit WEP (5 chars) and D-Link (and the rest of the Windows wireless universe) supports 64 bit WEP (7 chars), but they both support 128 bit WEP. I assume you could set both up as an open network if you were far enough from your neighbors, but I am in a townhouse complex, so I thought I probably better have some security on the network.
Now I only see one network (the one set up on my D-Link router) and I can print to my printer and stream to my stereo through iTunes (without disruption). Seems to work seemlessly now.
I should also mention that I did about three other things. I moved the LAN subnet on the D-link router to 192.168.1.1 (DHCP client address are now between 1.100 and .1.200) I had heard that this was necessary since both routers tried to use the 192.168.0 subnet, but I think this is only necessary in relay mode. I also statically assigned the IP address for the Airport Express. Finally I set up a firewall rule of Source WAN/LAN IP addresses of 192.168.1.100-200 of any protocol from ports 1-20000 to the same destination address range should be allowed to allow for all LAN traffic to be passed. I am very certain this is unnecessary and possible dangerous for security, but I thought I should mention that I did it.
Hope this might help someone.
Michael
iBook G3 (600 MHz) Mac OS X (10.4.3) D-Link DI-524 Router. Motorola Surfboard Cable Modem. Comcast Broadband

Can I connect airport express 802.11g (old version) with iphone3GS?

Hi all,
I have an airport extreme that I set up 2 years ago. It works with my computer, using itunes (although it disconnects constantly).
I'd like to set it up with my ihpone but I don't see it in the wifi settings and I don't see it in the airport utility.
I have the latest iOS5 on an iphone 3GS and the airport extreme is not the latest 802.11n but the version before that one.
Should I be able to connect the iphone to the airport extreme to stream music for example?
thanks for your help.

Should I be able to connect the iphone to the airport extreme to stream music for example?
Although the iPhone can connect to the wireless network, provided by the AirPort Extreme, you would still need either an AirPort Express or Apple TV (performing as an AirPlay speaker) to get the stream from the Extreme to either a set of powered speakers, audio receiver, or TV to hear it.
I haven't verified it as I don't have an 802.11g Express lying around, but AirPlay (which has evolved from AirTunes) may not be fully supported. I'm sure someone who has this model Express can chime in.

AirPort Express SLOW Wifi speed-Fast with Ethernet?

I am having troubles getting the speeds I’m paying for through Comcast. I am paying to get 105Mbps, but only receiving 61Mbps on average. I don’t expect to get 105, but 90 would make me feel better about what I am paying for.
Here’s my problem:
I attached my Ethernet cord and receive downloads of 125Mbps. Off the charts! Though, when I disconnect it and use Wifi it drops to 61Mbps. The highest I have receive was 71Mbps.
I pulled up my Wireless Diagnostics and found my rate (of transfer?) is 300 Mbps. On occasion, it does drop to about 220Mbps., but usually sits at 300. My dBm (signal-to-noise ratio) is between 35-40 average. Interference is not the issue as I have moved the computer within 1 foot of the Airport Express and received these stats.
I feel the answer lies within the AirPort Express settings. I feel as if the AirPort Express is limiting the transfer rate somehow. I do know If anyone has any ideas or needs more info to solve this crime, please respond. Thanks for the help ahead of time!
Adam S.
iMac (27-inch, Late 2012) running Yosemite 10.10.3
AirPort Express 802.11n (2nd generation) Model No. A1392
Motorola SURFboard®/ARRIS DOCSIS 3.0 SB6121 Channel bonding of up to four downstream  channels and four upstream channels increasing data rates to well over 100 Mbps in each direction  
Supports IPv4 and IPv6 to expand  network addressing capabilities  
Four times the current maximum user data throughput approximating 172 Mbps.

I don’t expect to get 105, but 90 would make me feel better about what I am paying for.
90 would be miraculous for an Internet connection through the WAN port on the Express for a wireless broadcast, even if the wireless device was close to the Express. Take a look at recents tests of the Express:
http://www.smallnetbuilder.com/tools/charts/router/bar/113-5-ghz-dn-c
40 Mbps was top speed for 2.4 GHz
42 Mbps was top speed for 5 GHz
If you are getting 60, you are doing very well indeed.....quite a bit above average for an Express
I checked my 2nd Gen Express again and on a 100 Mbps Internet connection, I got 44 Mbps at 2.4 GHz and 45 Mbps at 5 GHz with the laptop located a few feet from the AirPort Express.
If you are doing better than that, I would call it a day.

Anyone have any ideas why i can no longer see my Airport express speaker in Airtunes?

for the last couple of days i no longer can see my itunes speaker from an old Airport Express (V 6.3) 802.11g. Airport Utility 5.6 still lets me set it up, so I can see it there. but for some reaason i can no longer see that speaker selection in itunes or any of my devices. Any ideas? Thanks.

Hi Murray,
What version of Acrobat or Acrobat Reader are you using? Are you trying to open the PDF files from the Finder, or in Acrobat/Reader?
We look forward to hearing back from you.
Best,
Sara

Airport Express Airplay no longer compatible with iTunes 11.3

Hi,
Everything was working perfectly until this morning when I updated to itunes 11.3 (54) 64 -bit, now I open my itunes and try to select my airplay speakers connected to an Airport Express and the message appears "The Airplay device is not longer compatible with this version of iTunes" I have a Mac Book Pro with OS X 10.9.4 installed.
Any help will be much appreciated.

My iPhone, iPod, iPad and any other device sends the music perfectly through, just my Mac with iTunes is the one having the issue.

Airport Express Speaker output very quiet with 60-cycle hum

Similar Messages

Maybe you are looking for