Airport Express suddenly not extending

First, some technical info.
I am using a late model Airport Extreme with an early model Airport Express to extend my network. All has been working fine until recently. The Airport Express blinks amber and the utility says the connection is good but that the Base Station was unable to extend the network. I have not many any changes to either my Airport Extreme or the Airport Express. Have unplugged the Express and plugged it back in, but get the same result. What would cause it to suddenly drop off the network? Thoughts?

AMAZING!
Setup: AirPort Express extends Time Capsule both on 7.6.4
Symptom: Suddenly AirPort Express blinks and AirPort Utility says AirPort Express seems to have problem extending the network
Solution: Google "airport express not extending" and click link to "Airport Express suddenly not extending"
Problem solved in seconds!
PS: I wasted 5 minutes earlier when I pressed the reset button in my AirPort Express hardware and had to reconnect it to my internet connection as the extending network although the setup was very intuitively easy ( a very intelligent setup sequence all figured out by Apple ) ... then I read this !

Similar Messages

AirPort Express will not extend Wireless Network

Hello. My airport express will not extend my wireless network. It was green for about the first 4 hours and then I've had a flashing yellow light since that time. I've reset it a bunch of times and even have the AE in the same room as my AP Extreme. I complete the setup and then it continues to flash yellow. Can ayone give me a hand?

In the cases where the AirPort base stations would be interconnected by Ethernet you want to configure then for a roaming network, NOT an extended network. Apple uses the term "extended" when the base stations use wireless connection. Regardless of naming convention the end results is pretty much the same.
The link I provided should provide you with the necessary steps to set this type of network up.
If you need additional help, please start a new post as the solution for you will be different than the OPs. Thx!

Airport Express wil not extend wireless network via ethernet

I need maximum bandwidth in a area with poor signal. No matter what I do, the AE will not extend my APEBS dual band via ethernet. It will alway connect wirlessly giving me half the speed. I have 1 main network to extend. I have tried to extend the 5 GHz wide channel as a seperate network but this wont work either.(but thats what I want really. Please help. I have been at this a couple days already and I need to figure it out before my return policy wears out. Thanks!

If you are connecting the Airport Express to your AirPort Extreme via ethernet, the AirPort Express should be configured as follows:
Open AirPort Utility, click Manual Setup
Click the Wireless tab just below the row of icons
Wireless Mode should be set to "Create a Wireless Network"
Wireless Network Name would be the exact name of the main network that the Extreme is creating, same security, password.
Radio Mode must be set the same as the main network on the Extreme
Channel should be set to be least 6 channels apart from the channel that the main network is using on the Extreme.
Click the Internet icon above and look for Connection Sharing at the bottom of the page. This should be set to "Off (Bridge Mode)".
Update to save settings.
For more info reference page 42. http://manuals.info.apple.com/enUS/Apple_AirPort_NetworksEarly2009.pdf

Airport Express can only extend network, not create new one. Why?

I am sharing a flat with some friends. The shared broadband router is placed in the living room. To strengthen the signal and make it easier for me to manage, I bought an Airport Express, connected it to the shared router with an ethernet cable and set up a wireless network of my own in my room. It was working fine, until recently we renewed our broadband contract. The router had been replaced by a new one (I don't know why) and the network configration had been changed. Since then I was not able to use my own network. In the Airport Utility display, the light of Airport Express is green, but the light of Internet is yellow, and the status is disconnected. I tried to change various other configuration on the Airport Express, and all in vain. Until I switched the network mode from 'Create a new wireless network' to 'Extend a wireless network', the Internet connection was finally back online. But this merely extends the existing network and not what I want. Why this happens? Why my Airport Express can only extend a network, not create one?

Here is the situation on my Airport Express.
If I choose to extend the existing wireless network, the Airport Utility shows like this:
If I set up a wireless network of my own, what I get in the Airport Utility is this:
See my problems here? The Airport Express does not show anything in amble, but the Internet complains that there is no connection.
This problem did not occur before the broadband was renewed and the rounter was replaced.

To configure Airport Express as an extender to Airport Extreme ?

- I have an Airport Extreme , its been there for 2 years
- I forgot the admin password to login to the airport extreme, but I remember
the wireless password. I cannot rest it as I cannot loose the configuration.
- Now yesterday I brought a new Airport Express to make this as an wireless
extender to the current Airport Extreme wireless what I already have.
Question:
========
1) While configuring this new Airport Express as an extender to my current wireless setup (Airport Extreme), does it need the ADMIN password of the airport extreme anywhere ?
2) Will there be any difference in the wireless signal & strength in the below
setup ?
Airport Extreme <== connected through CAT6 network cable ==> Airport Express
Versus
Airport Extreme <== connected wireless ==> Airport Express

Welcome to the discussion area, johnpau2009!
I have an Airport Extreme , its been there for 2 years
Just to confirm which version you have, is your AirPort Extreme (AEBS) square shaped with rounded corners, or is it round and shaped like a flying saucer?
I forgot the admin password to login to the airport extreme
Push the reset button on the back of the AEBS for 1 second and give it 20-25 seconds to restart. You now have about 4 minutes to make changes. If you are asked for the admin or device password, try "public" (without the quotation marks)
Click the Base Station tab below the row of icons to check then name of your AEBS and type in a new admin or device password. (Might be a good idea to write this down).
Click the Wireless tab below the row of icons and look for an option with a check box to "Allow this network to be extended". Enter a check mark here.
Write down the name of the wireless network you have established and the exact setting that you see for Wireless Security because you will need that information to configure the AirPort Express (AX) to provide additional wireless coverage
Click Update at the lower right to save your changes and the AEBS will restart in 25-30 seconds and you should have a green light.
Post back on your progress at this point.
2) Will there be any difference in the wireless signal & strength in the below
setup ?
Connecting devices using ethernet cable connections is always the better way to go because this provides much better bandwidth (speed) for the wireless network and it allows you to place the AirPort Express in the location where it's really needed.
Using wireless only to extend can work well if you have close to a line of sight relationship between the AEBS and AX. There's nothing wrong with trying this first to see if it will provide the performance you want if you're not anxious to pull ethernet cable through the house.
Message was edited by: Bob Timmons

Airport Express as wireless Extender to Time Capsule

I have an older airport express that I used to use as an Wifi extender for my Time Capsule. I have a Macbook Pro running Os 10.8.4, and the airport utility now gives the following error:
This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information.
Since OS 10.8 does not support Airport Express 5.6, I have an old Mac I've been able to access Airport Express on and was able to ensure that everything was setup correctly as a wireless extender. However, None of my computers, Ipads, or Iphones are benefitting from this as an extender. Is it possible to use this older airport express as an extender still or has Apple completely blocked me from using it even as that any longer? It used to work fine, until I updated the OS from 10.7 to 10.8, and now it no longer functions.
Thank you!

That article addresses installing AU 5.6 on a Mountain Lion system, not the ability to "wirelessly extend" an 802.11b/g - only Express. That ability is available for 802.11n - capable base stations only:
Multiple Wi-Fi base station network types
If you need to extend the range of your wireless network, which method should you use?
For 802.11a/b/g/n Wi-Fi base stations:
Roaming Network (Recommended)
Wirelessly Extended Network
For 802.11g Wi-Fi base stations:
Roaming Network (Recommended)
WDS
Which of the above configurations applies to your network?

Airport Express won't extend Airport Extreme Network

I use an Airport Extreme (AE) to connect to the internet. I use an Airport Express (AX) to extend the network via a WDS network. Until recently all was fine.
Last week I updated the firmware for my AE. Since then my AX has not been acting as a WDS extension. I have tried several times tonight to make the AE and AX talk to each other in this fashion. I have reset the AX to factory defaults and reset the AE as well. So far, nothing works.
Thought the AX might have failed. However, the AX will connect to the AE network just fine. It just won't extend the network.
Any ideas will be most appreciated.
Thanks.

I have an Airport Extreme Base Station. I just bought an Airport Express to extend my network and connect a wired device in my living room to my network via the Ethernet port. The Airport Express obtains an IP address from the Airport Extreme but I can't seem to get out to the Internet ...at least via the Ethernet port. When I installed the Airport Express, I updated it to 7.3.1.
This sounds like a similar problem to the original post.

Airport Express will not talk to my router

I have 2 airport express stations that are 6.3 and they have always been able to connect to my qwest wireless router no prob. I've recently updated to Leopard and was surprised to see the new airport utility instead of the airport admin and airport setup tools. I like the new utility and interface as it seems less confusing than the old but now I'm having issues.
1. I can get the new utility to recognize my airport express ONLY when I do a hard reset to the airport express.
2. As I've done many times in the past, I go through the following setup protocol to join my current wireless network. I simply want to join my current network so I can talk to my stereo and printer wirelessly.
3. When I finish the setup and hit update, the airport utility updates the express successfully and then attempts to restart the express in order to join my network. This is where the problem lies.
*Here's the error message I get:*
AirPort Utility was unable to find your Apple wireless device after restarting.
The settings for this Apple wireless device have been successfully updated, but there was a problem re-joining the wireless network or finding the Apple wireless device. You may need to select your network from the AirPort menu and try again.
Now, I've tried repeating this process 10 times with both airport express stations and the same result happens? Remember, the only way for the utility to find the express is to hard reset the express. What gives? I bought both of these express stations over a year ago and they've been working fine til now. Because they are older and updated to 6.3, I shouldn't update them to the 802.11n7.3.1 update or should I? Is there something different about this new airport utility in Leopard that is causing the problem?
Like I said, I've done this exact same thing many times and its pretty straight forward but I'm stumped.
Anyone? Thanks in advance

I've got the solution! It took me some fair hours, though...
It seems the Airport Express can not handle the WEP-encryption properly, nor the 64 or the 128 bit versions. Here's how to work around it:
1) change your routers encryption to WPA2 with passkey (WPA-2-PSK). You may use the 10-digit code supplied with most routers or any of your own choice.
2) Change all wireless cards in your network to WPA2-PSK. It can take some time to figure it all out, but in the end you'll fix it. I had to download a new driver for my D-Link card DWL-G650 for instance.
3) Do the usual config thing with the Airport Express. Choose to connect to an existing network, apply the 10-digit passkey (be sure to choose the WPA2-PSK-option in the drop down-menu).
4) Off you go! Itunes will find the remote speakers, green lights all over and everybody turns happy...
/W

My new airport express does not connect my printer to my computer? My old airport did! then I updated to OS 10.9.2. How do I get it connected?

My new airport express does not connect my printer to my computer. The old airport did. I recently updated to OS 10.9.2. I have since bought a new
HP 6700 all in one wireless printer, got the latest Comcast router. None of which connect to my computer wirelessly. Which do I throw away the printer, router, or Mac? Help

Contact HP for support.
Explain that you are using a Mac, anticipate the inevitable groan, and wait patiently for their resident Mac expert to return from vacation.
Until then download and install its driver here: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=5058338&cc=us&dlc=en &lc=en
Otherwise return the printer and purchase one from a company that visibly supports OS X. HP isn't on that list.

"Airport Express" is not compatible with this version of itunes

Hello- My itunes reports that my airport express is not compatible with this version of itunes. My ipod and iphone no longer sync with the device either. Any suggestions? Thanks!

Does anyone out there have any advice? I have had no success correcting this problem........

HT1515 my airport express in not detected?

my airport express in not detected by my airport utility, and i want to conected to the wi fi of an internet conection.

In order for AirPort Utility to be able to detect your AirPort Express you need to either be connected to the AirPort Express via WiFi or by connecting an ethernet cable from your computer to the Express.

Hi, The Airport Express does not work with iOS 7.0.4, I appreciate your help to resolve this event. Thank you,

Hi, The Airport Express does not work with iOS 7.0.4, I appreciate your help to resolve this event. Thank you,

Please locate the model number of the AirPort Express and post back that information.
The model number is located on the side of the AirPort Express. It begins with an "A" followed by four numbers.
We are not sure what you mean by "does not work". Does this mean that the AirPort Express worked at one time and has just recently stopped working?
Have you installed a newer operating system on your iOS device recently?
Or, is this a new AirPort Express that you are trying to configure for the first time?
If yes, what service will the AirPort Express perform on your network?
Please remember that we cannot see your network, so we only know as much about your problem as you can tell us.

Need Help...my wireless airport express will not work with my update of snow leopard

after installing snow leopard on my macbook pro my airport express will not work...or will connect only for a minute at a time.

If you mean by "airport express" the square airport router you plug in and has a usb port then run the Airport Utility located in your Utilities folder to set it up again. If AU doesn't see it you may need to do a re-set of the AE.

How do i set up an airport express as an extender for my airport extreme

how do i set up an airport express as an extender for my airport extreme

Check these discussions:
Best bets to extend/boost signals from Airport and AP Extreme
How to extend and Extreme network using Express

Airport express does not appear in Airport Utility

Hello,
I am having problems connecting my Airport Express to my network.
My configuration is all Apple. I am attempting to set up Airtunes. I have an Airport Extreme (software version 5.7) plus Airport Express. The Airport Extreme is hardwired to my Power Mac G5 (10.5.6) via ethernet. Wireless security is WEP 128 bit.
The Airport Express appears to establish a connection with no problems. The indicator light on the Express goes through normal start up and then a steady solid green.
Airport Utility shows the Airport Extreme but the Airport Express is not listed.
Any suggestions on how to make the connection are appreciated!
Thank you!

When having difficulties accessing the AirPort thru the AirPort Utility, try the following, in order checking accessibility with the AirPort Utility after each step:
o Check the local connection. If you are trying to access the AirPort wirelessly, make sure that you are connected to its wireless network before running the AirPort Utility to administer it. If you are still unable to access it with the utility, temporarily connect your computer directly using an Ethernet cable to one of the base station's LAN ports.
o Power cycle the base station. Remove the power adapter's plug from the power outlet, and then, wait 15 seconds before plugging it back in.
o Perform a "factory default" (AirPort Express) or "hard" (AirPort Extreme / Time Capsule) reset.

Airport Express suddenly not extending

Similar Messages

Maybe you are looking for