Airport Express, Vista and FON Wireless network

Hi. I have a strange behavior on my wireless network. I configured my Airport Express as part of my wireless network managed by the Fonera (FON Network router). The Airport Express is always on as the wireless network. Yesterday all was working fine and I was able to play music and surf the net without a glitch. I started iTunes, the software found and connected the remote speakers and music was playing while I continued to surf. Today I restarted Vista and connected wirelessy to the Internet. As soon as I started iTunes I found that my Airport Express was no more available (it was still on since yesterday). I started the AirPort Utility, found the Airport Express and went again through the process of let it participate to my network, reset the WPA and add (again) the password. The Airport restarted but it was unable to find any wireless network. The reason is that in the process the Fonera has been reset to different settings!! I put again the right parameters in the Fonera and is back working. How come that adding the Airport Express to my network, the wireless network itself is reset? In my opinion this should not happen. Any ideas? Thank you very much, Massimo

Hi Donny
I had the same problem with my airport. In the end I got it printing by sending it to the Ip adress of the base station(10.0.1.?/192.168.2.?). I sent it through a custom made port which went to that Ip adress as well.
Hope this helps.

Similar Messages

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

Using Airport Express to extend my wireless network

I recently purchased a Time Capsule but found that I could not see the wireless signal from my bedroom. To solve this I purchased an Airport Express to extend the range. I plugged the AE into an outlet in my bed room and set it up to join my existing network. Everything looked fine from the point of view of the Airport Utility. Unfortunately my iPod Touch still can not see my wireless network from my bedroom. I new iPad can see it but the signal is very weak, even when I hold it right next to the AE. Is there a setting I missed?

Rick, welcome to the discussion area!
I plugged the AE into an outlet in my bed room and set it up to join my existing network.
You need to configure the AirPort Express to "Extend a wireless network". The AX does not provide any additional wireless coverage when it is set to "join".
First, you need to check a setting on your Time Capsule as follows:
AirPort Utility > Manual Setup > Wireless tab (below the icons)
Make sure there is a check mark next to "Allow this network to be extended"
Update to save any changes
On the AirPort Express move it close to the Time Capsule for configuration:
AirPort Utility > Manual Setup > Wireless tab
Wireless Mode = Extend a wireless network" (Hold down the option key on your Mac if you do not see this choice appear when you click the selection box).
Wireless Network Name = Same name as your Time Capsule Network
Check mark next to "Allow wireless clients"
Security = Same setting as your Time Capsule
Password = Same password as your Time Capsule
Confirm Password
Update to save settings
The AirPort Express can only "extend" what it "receives". Most users position it too far away from the main router and consequently, the Express extends a weak signal. Try a location that is about 1/2 to 2/3 the distance between the Time Capsule and the area that needs move coverage. Then experiment a bit to find the best signal.
Post back on your results.

Airport express failing to extend wireless network

Have got an airport extreme connected via ethernet to my Virgin Media hub (hub is in modem mode). Also have an airport express to extend the wireless network. Setup has been working perfectly for over a year, then this weekend, literally no settings have been changed, and airport express is giving me a status message of "This airport base station was unable to extend the wireless network. Make sure the wireless network you're trying to extend was setup and is working correctly, that you entered a matching wireless network password into this device and that this device is in range of the wireless network"
I have reset to factory settings 3 times now and whilst it goes through the initial setup, i always get the same status message. Front light is green.
The express version I'm using is the 2012 redesigned version, looks like a white Apple TV and it has the latest firmware. I've tried configuring via my MBA, windows desktop pc (windows 7) and ipad, nothing works
Any ideas?

You have to think of the Express devices as matching pairs when you have one set up to create a wireless and the other to extend it. Here, I assume that you still have the extending Express set up to extend the network.
Power off both AirPort Express devices. The power down order does not matter.
Wait a minute
Power up the main AirPort Express.....the one directly connected to the Virgin hub....and let it run a full minute
Then, power up the extending Express
Check the network and report on your results

Airport Express won't extend wireless network

I think due to a fault my airport express wont extend my wireless network around my house , but it will allow for airplay ... is it possiple to extend my network using the express but with an eithernet cable rather than the wireless that is transmitted out of the express unit ??

Is the other wireless router, that you are trying to extend, another AirPort or Time Capsule base station? If so, are both units 802.11n models? Finally, what is the rough distance between the units and are they located in the same room, different room, or different floor?

Can I use my airport express to extend a wireless network with a non-apple router?

I have been trying to extend my wireless network in my house. Right now I have a dsl modem/router provided by Century Link and an older AirPort express (not sure how old but it uses AirPort utility v5.6). I want to be able to share my printer and use AirTunes. Currently I have the AirPort plugged into the router and setup to create a new wireless network. I would like to combine them so I don't have to switch between to print and play music. I am not really sure where to start or if it even possible. Any info would be great!

If you keep the Express connected using Ethernet and configure the Express to "Create a wireless network" using exactly the same wireless network name, exact same wireless security and same wireless password as the Century Link network.....everything will behave as one "big" network, and you will have additional wireless coverage near the Express.
If you do not need extra wireless coverage, you can turn off the wireless on the Express.
The Express must be in Bridge Mode.
Most users know the name of their wireless network and password, so the really tricky part of doing this is that you must know exactly what type of wireless security settings the Century Link router is using....and then match up the same settings on the AirPort Express.
If the settings do not match up exactly, then you wind up with two separate networks that will each require their own log on.
If you can check the setting for wireless security on the Century Link router and provide that information to us, we can tell you how to set things up the way that you would like.

Adding Airport Express to D-Link wireless network

We have a D-Link wireless router given us by our ISP. I have an Xbox 360. I'd like to take one of our Airport Expresses, and connect the 360 via Ethernet cable to the Airport Express, while the Airport Express joins the D-Link's network, thus giving my 360 wireless internet.
We used to accomplish this using another Airport Express instead of the D-Link, but for our own reasons, we now need to use the D-Link.
Is there a way to add the Express to the network for this purpose?

"Is there a way to add the Express to the network for this purpose?"
Yes, configure the Express to "Join" the wireless network created by the D-Link and check the "enable ethernet clients" box. Post back if you need step by step on this configuration.
It's possible that this may work OK for you if you have a strong, fast wireless network. But, you may also want to consider that this would be quite a way down on the list of most desirable ways to connect the 360 to your network.
For the best video quality, suggested in order of preference:
Ethernet cable from one of the LAN ports on your router to the 360
Ethernet powerline adapter at the router end and another adapter at the 360 end
Wireless from your D-Link to the 360's wireless-if it will accept a wireless connection
Wireless from your D-Link to the Express. Ethernet from the Express to the 360
Would be interested in your feedback on your experience if you use the Express.

Airport Express wouldn't extend wireless network

Am posting this in case it helps someone else. I have an Airport Extreme set up as a base station and couldn't get an Airport Express to "extend wireless network". I finally found a checkbox in the "Wireless" tab of the "Manually Configure" dialog box for the Extreme that says: "Allow this network to be extended". I could not find this referenced anywhere in Apple documentation, so you have to know to go and check this box. Apologies to the techies if this is a no-brainer, but I only found it by accident. Apple should include a brief paragraph in their wireless troubleshooting guide on extending your network.

When you configure the Express to "join a wireless network" it becomes part of the network so that you can stream AirTunes to the device or use a remote printer connected to the USB port, but it does not provide any additional wireless coverage in this type of configuration.
"Extend a wireless network" does the same thing as above, except the Express will also provide more wireless coverage in the area where it is located.

Airport Express joining Linksys WRT54G Wireless network

I have spent hours trying all different ways of getting my Airport Express to join my Linksys network. And then I discovered that I have to *__remove the spaces from my WPA password__* in order for my AX to join the network. My iMac and MacBook all join the network with spaces in the password, but for some reason the AX does not.
This may be superstition, but I also made sure the pass phrase was all uppercase and exactly 13 characters. Don't know if that makes a difference, but I was tired of trying different things.
Hope this helps some one.

I have spent hours trying all different ways of getting my Airport Express to join my Linksys network. And then I discovered that I have to *__remove the spaces from my WPA password__* in order for my AX to join the network. My iMac and MacBook all join the network with spaces in the password, but for some reason the AX does not.
This may be superstition, but I also made sure the pass phrase was all uppercase and exactly 13 characters. Don't know if that makes a difference, but I was tired of trying different things.
Hope this helps some one.

How can I use an Airport Express to join my wireless network and provide an internet signal to my Power Mac g5 via an ethernet cable?

I have a power mac g5 that does not have a wireless card, and connects to the internet via ethernet cable.
I want to know how to set up an airport express so that it joins my wireless home network and provides the G5 with an internet signal.
This via an ethernet cable that is plugged into the airport express and then into the ethernet port on the g5.
Please advise as I have configured the airport express in every way possible, the green light is on and when I plug the ethernet cable into the G5 my network cofigurations shows nothing and says that the ethernet cable is not plugged in (It is).
I get an internet signal if the ethernet cable is plugged directly into my wireless router, so the ethernet port works.
Please assist. Thanks.

Two requirements that must be met to do what you want.......
1) An AirPort Express 802.11n must be used. Check the Model No on the label on the side of the Express. It needs to be A1264. Any other model number will not do what you want.
2) The Express must be configured to "Join a wireless network" and the option to enable Ethernet Clients must be checked.
Open AirPort Utility and click Manual Setup
Click the Wireless tab below the row of icons
The box to "Allow Ethernet Clients" must be checked
Please check to verify that your AirPort Express meets both requirements

How do I use airport express to extend my wireless network?

How vcan I extend the range of my wireless network using Airport Express?

It appears that you may have "join a wireless network" and "extend a wireless network" mixed up a bit.
The Express can "join" virtually any wireless network produced by any manufacturer's router if it is provided with the correct settings:
name of the wireless network
the correct wireless security settings
and correct password.
"Join" is normally used for AirTunes or to connect a USB printer to the Express for remote printing.
But, the Express does not provide any additional wirless coverage when it "joins" another wireless network.
Apple's "Extend a wireless network" feature, which was introduced about 5 years ago, allows the Express to connect to another Apple "n" wireless router and then "repeat" or "extend" the wireless signal....providing more wireless coverage in the area where the Express is located.
This is a proprietary setting. Apple says it will not work with devices from other manufacturers. To our knowledge, this is correct.
Prior to 2007, Apple used a setting called WDS to allow the Express to be configured to provide more wireless coverage. Attempts were made by a number of manufacturers to standardize the WDS settings, but things were never finalized.
The result is that Apple's older "b/g" routers were sometimes compatible with WDS settings from another manufacturer. There were a handful of products....5 or 6, as I recall....that were said to work. Some did, some didn't. Linksys had a couple of models, Netgear had one, SMC another, etc. Extremely limited.
Since WDS was never adopted as an industry standard, manufacturers developed their own WDS settings. Compatibility was extemely limited and unreliable. That continues to this day with WDS.
Bottom line....It is always best to stick with the same manufacturer throughout your network as far as routing is concerned.
If you have an newer "n" Apple router like an AirPort Extreme, the Express can extend the wireless as can along Extreme. If your Extreme is dual band, and you want to extend both bands, then you need another Extreme.
Another responder suggested to someone that they could connect the AirPort Express to a router via Ethernet. What exactly would that achieve?
That is a completely different subject since this discussion is about extending a wireless network using wireless only.

Can't connect Airport Express to my main wireless network, just my guest account.

I go to join my Airport Express to my wireless network so I can play music from Itunes to my sound system in my living room. That is all I want to use it for at this point. I pull up a list of the networks available, and my guest network shows up on the list, but my main network, which all my computers and Iphone is connected to, isn't on there. I have a Linksys E3000 with a guest account set up trhough it. Windows 7. I called tech support and they said something about a hidden setting. I went and checked and couldn't find anything about this. Also, when people come over they can access my main wireless account with my password.

Hi JWHITHAM and welcome to the forums!
Have you tried manually adding your wireless network to the iPod touch? Mine does the same too sometimes and I just add it manually. So far it works.

Can't get Airport Express back onto my wireless network???

Just returned from a trip where I had successfully used my AE in temp accommodation. Now I can't get the thing to rejoin my home network. I've reset it time after time, I go through Airport Setup Asst and get to the bit where it says it's updating the AE, congratulates me on setting it up - but the thing never rejoins and all I get is the amber blinking light. Once this happens it disappears off the network until I again, reset to factory settings.
I have tried entering WEP equiv passwords as well as the ASCII but am not sure which one to use now - totally confused. I have another AE on the network which is working fine. I must be missing something unless the thing has gone u.s?
Any ideas would be gratefully received.
Cheers
Chris
iMacs, Intel 20 inch 2.0 with 1.5 gig ram Mac OS X (10.4.9)

Hi Dan
I have posted a new topic on this because I feel strongly about it.
Here's a copy and paste of what I said:
"I have spent literally the equivalent of 3 full days, configuring, reconfiguring, re-installing, setting up, un-setting up, scouring the internet, phoning people, taking trips to the Apple Store to find a solution. All a total waste of time. Why? Because until there is an update to cure the problem, the Airport Extreme BS will not function properly when used in an environment other than a basic setup.
My network at home consists of 3 XP PC's, two Airport Expresses, and 5 Macs of various models. Until I removed an Express to use it on a trip, all of it worked well. When I came to return said Express into 'the fold' - that's when the trouble started. Mainly that, unless I had security switched to NONE, I couldn't connect the Expresses to the Base station, and my HP PSC2510 wireless printer would not connect either.
If you are anything like me, you will have been through every single combination of setups, restarts, reinstalls you name it. I got conflicting info about the level of security from the Admin utility - sometimes it would report WPA, others it would say WEP.
Cut a long story short, I finally returned the BASE Staion to the Apple Store and got a replacement. I had narrowed it down to that component only. Everything else on the network "seemed" to be fine.
I wondered whether it was a solitary, faulty AEBS, and by replacing that, it would eliminate the problem. In theory.
Brought home new AEBS but this unit also suffered collossally unreliable/unsuccessful connections from Printer, Expresses and one XP laptop.
I have been to the Moon and back with Hewlett Packard trying to work out what could have happened - overnight - to this normally fail-safe wireless printer. No clues, all seemed to be set up correctly. But it WOULD NOT JOIN THE NETWORK!!!.
So, as any mad (as in angry) scientist would do, I set up a "Control" experiment. Keeping everything as it was, all I changed was the AEBS. I swopped the AEBS for my older white AEBS (flying saucer). Guess what?
Within seconds, all connected. Including printer, Expresses, and XP PCs.
All working perfectly. Wrote down all the settings to check exactly the same as on the new (n) AEBS - identical. Swopped back - same problems. No way would it work.
I am no Network expert but have a feeling that it has a problem managing/distributing/assigning IP addresses. Dunno, just a hunch because the printer would connect fine when connected to AEBS by ethernet cable.
So I am now going to return the new AEBS to Apple and get a refund. I don't have time for this and I suggest not many people do.
So if you have a problem like I did, it might be an idea to try another router or eliminate it somehow and check your settings.
I hope this helps.
EDIT:
Looking again through a lot of posts on here - I would estimate that they are pretty much linked to the same problem - a few are reporting problems after connecting to different ISP then not being able to get it working again, some saying they can't get a single solitary PB to connect but al the others do. It all rings bells here! I am sure it's an IP problem (but what do I know) I would love someone to see into this. I doubt whether Apple will come up with something before Christmas - let's hope they prove me wrong eh?
Anyone know of a good, reliable wireless router that also allows external HD sharing?
Cheers!
Chris"

Why does Airport Express slow down my wireless network??

Hello, guys! Here I am again, seeking for help...
Ok, so here's the situation: my internet service provides me with 10Mbps. My cable modem is hooked up to a 4-month old Airport Extreme in my home office, two walls away from the living room, where I'm typing from now. Internet's wireless speed in this living room has always been about 10Mbps, barely any loss when switching my signal from cable to wireless.
I then decided to buy an Airport Express in order to extend my wireless network, since I want to work in a room far from this living room and with Airport Extreme alone I got no internet signal there.
Ok, so I installed the Express right at the living room (I can say it's pretty much at the middle of the house) and now I got full internet sign at the far room, great!
HOWEVER, my wireles speed has been cut by half!! At this very same living room where the signal was 10Mbps before I installed the Aiport Express, it's now - at the very best!- 5Mbps!! Needless to say that it's even slower at the far room it was intendend to extend the signal to, but that was kind of expected.
*But why does it cut in half my internet speed at the living room if Airpot Extreme IS delivering 10Mbps at that point of the house??* Am I not setting it up properly, how can I solve this??
Thank you so much for any help you can give me!
Cheers,
Renata
Message was edited by: rgobrasil

After some more analysis, I discovered that this tends to happen everytime a Time Capsule backup is performed.....

How to add airport express to my current wireless network

Hi guys.
I have a dlink router (ac) configured as NAT and a friend of mine gave me an airport express (ac) to extend my current wireless network.
I believe that i should configure the airport express as bridge mode in order to mantain my current ip range.
I'm trying to configure the airport express but i can't even loggin to it.
The question.
Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
Thanks so much and any help would be really appreciated.
Regards.
Francisco.

Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
Unfortunately, the answer is that neither an AirPort Express nor an AirPort Extreme is compatible with a D-Link router....or any other 3rd party router for that matter.....if you are trying to have the the AirPort device extend the signal using wireless.
The AirPort Express can extend a signal from another Apple router.
'm trying to configure the airport express but i can't even loggin to it.
You may have received an older version of the Express that is not compatible with the newer Mac operating system that you are using.
Look for the model number of the Express on the side of the device.....hard to see in the faint print.....you may need a magnifying glass. If you see model A1084 or A1088, these older versions are no longer supported by Lion, Mountain Lion or Mavericks operating systems.
The workaround is that you must use a Mac that is running Leopard or Snow Leopard, or a PC to be able to administer the older versions of the AirPort Express models.

Airport Express, Vista and FON Wireless network

Similar Messages

Maybe you are looking for