AirPort Express vs. 3rd Party Wireless Routers

I'm confused!
The AirPort Express is just a wireless router, right. What is the benefit of the unit over other wireless routers?
I am basically trying to find the cheapest way to connect wireless to a DSL modem.
I have always used standard dialup and am looking into High Speed DSL service.

Your not confused, Airport Express, and Airport Extreme both are Wireless Base Stations.
If you are looking for the cheapest way it probably won't be using Apple products.
But on the other hand if you are looking for ease of set-up and reliability, and if you will READ THE BOOKLET that accompanies either one them, then you will be more than satisfied with Apple Products.
I realize that Dial-up,, sometimes is the only choice.
But using DSL, or Cable is like trying to comparing a Turtle to a Cheeta.
Reliability, Speed is so much better, depending on your Internet Service Provider.
I suggest, if you are hung on cheapest, go to your local computer store and talk to one of the associates. I fear you might be overwhelmed by the myrid of choices. All Manufactures have good products it really boils down to what exactly it is you are trying to do.
Not all Stream Music as well as other features that Apple does. Have a look at these 2 links.
http://www.apple.com/airportextreme/
And
http://www.apple.com/airportexpress/
Good Luck with your choice.
Don

Similar Messages

  • Airport Extreme and third party wireless routers

    I have a dual-band Airport Extreme that works well with all of my newer Macs. I have older laptops, however, with PCMCIA wireless cards that can't do WPA2-Personal security, only WEP. My only solution has been to set up a Guest network with no security. Is it possible to connect a third-party wireless router to the Airport Extreme that offers WEP security?

    Are you trying to setup the Belkin router to use the same wireless network name as the AirPort Extreme network?
    That would require that that the Belkin's network use the same security.
    If this is the case, try setting up the Belkin with a different wireless network name. Unless the Belkin is really limited in features, you should be able to choose the type of wireless security to be used on this Belkin network.
    If you can do this, "point" your WEP device at the wireless network that the Belkin is producing and the signal will bridge when it reaches the AirPort Extreme.
    Regading your question about connecting a router to the ethernet port on a computer that is already setup for Internet Sharing...this is not likely to work. I very much doubt that you would be able to get an Internet connection with this type of setup.
    Message was edited by: Bob Timmons

  • Airport Express and 3rd Party Router

    I have a first generation Airport Express that I've been using for the past few years to stream music wirelessly to my stereo via my Belkin 54g router. At first I could not get the Airport Express to work with the Belkin Router but finally after posting on this discussion board, someone told me how to make it work.
    Well, I finally decided to buy a new router with the N-protocol (Linksys E2000) and I cannot get it to recognize the Airport Express at all, even when I hook it up via ethernet cable. I cannot remember the steps I went through to get the Belkin router to work with the Airport Express. I hope someone can help me so I can get it working again.
    Thanks,
    Mark Brandenburg

    Mark,
    You need to "hard reset" the AirPort Express by holding in the reset button until the amber light begins to blink more quickly, hold another 3-4 seconds when you see this, then release the reset button.
    Open AirPort Utility to reconfigure your AirPort Express to "Join" your Linksys wireless network. The AirPort Express should "see" the name of the Linksys network during the configuration, but the hard part is knowing exactly what type of wireless security that your Linksys router is using.
    You must enter a matching setting on the AirPort Express to get it to "join" the network correctly, so you may need to check the settings on your Linksys router first if you are not sure of the exact security setting that it is using.
    The other thing you need to check is to make sure that the Linksys is broadcasting a compatible signal so your older "g" AirPort Express will be able to join the network. If the Linksys produces an "n only" wireless network, the AirPort Express will not be able to join the network since it is a "g" device.

  • Airport Express used to extend wireless network from Linksys?

    I've been asked if I can straighten out a wireless mess at a local church. They have a wireless network in their office (a seperate small building) using a linksys transmitter.
    The church (a seperate building 50 yards away is where they want to extend the network to.
    Currently, I can read the network there on whqat they have now but something is misconfigured and the manufacturer is being of little assistance.
    Has anyone used an Apple Airport Express to extend a 3rd party wireless router? Ive decided it may just be worth the cost to dump the relay they have and simply buy an airport express.
    Suggestions?

    The Linksys WRT54G and WRT54GS (not latest versions v5) are the only 2 known Linksys routers compatible with Apple's WDS.
    So if you are using one of those routers you should be able to do it.
    If you are using a different router it probably will not work.

  • Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?

    Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?
    Flow would be
    Cable modem---->cisco e2000 wifi router (This is broadcasting wifi but not strong enough)---->4 port hub ---->airport express (to extend the wifi in another part of house)
    thanks!

    Yes, you can do this as you stated. In essence you will want to configure both routers for roaming network. Please check out the following Apple Support article that describes this type of network. Although this article uses two or more AirPorts, it can be done with just about any manufacturer's router.

  • I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

  • Does airport express stream directly to wireless speakers or does it need to be connected through an audio cable to an amplifier before the speakers

    Does airport express stream directly to wireless speakers or does it need to be connected through an audio cable to an amplifier before the speakers?

    I got an additional question bout this topic:
    is it possible to use both at the same time? in my case cable-connected speakers in the living-room and an Airplay-speaker in the bathroom and/or kitchen?
    so I select the Airport Express as Airplay-Output on my iPad and from there it's shared via cable AND wireless? this would solve the problem of being able to only select ONE Airplay-Output on my iPad at the same time...

  • Just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

    just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

    Temporarily connecting your AirPort Express to one of the Time Capsule's Etherent LAN <-> ports...as LaPastenagure suggests....is always a good way to setup and configure other network devices.
    If you want to configure the Express using wireless, remember that the Express broadcasts a default wireless signal with a name like Apple Network xxxxxx. You must log on to this network first....no password is required....then open AirPort Utility to "see" the AirPort Express.

  • Airport Express Card on a wireless PC network??

    Hey there, I was curious if it was possible to use a G5 with an Airport Express Card on a wireless PC network. My wife needs to be able to access the internet from another part of the house. Someone mentioned that it might be possible, but I can't seem to find anything explaining how to do it. Thanks for your time!
    Jeff

    Which wireless router are you using?
    Are you using WEP?
    One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
    In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
    The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
    One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
    Though sometimes not even that works and the HEX key must be used regardless.
    AirPort: Joining an encrypted wireless network
    http://docs.info.apple.com/article.html?artnum=106424
    Choosing a password for networks that use Wired Equivalent Privacy (WEP)
    http://docs.info.apple.com/article.html?artnum=108058
    iFelix

  • Using Airport Express to extend my wireless network

    I recently purchased a Time Capsule but found that I could not see the wireless signal from my bedroom. To solve this I purchased an Airport Express to extend the range. I plugged the AE into an outlet in my bed room and set it up to join my existing network. Everything looked fine from the point of view of the Airport Utility. Unfortunately my iPod Touch still can not see my wireless network from my bedroom. I new iPad can see it but the signal is very weak, even when I hold it right next to the AE. Is there a setting I missed?

    Rick, welcome to the discussion area!
    I plugged the AE into an outlet in my bed room and set it up to join my existing network.
    You need to configure the AirPort Express to "Extend a wireless network". The AX does not provide any additional wireless coverage when it is set to "join".
    First, you need to check a setting on your Time Capsule as follows:
    AirPort Utility > Manual Setup > Wireless tab (below the icons)
    Make sure there is a check mark next to "Allow this network to be extended"
    Update to save any changes
    On the AirPort Express move it close to the Time Capsule for configuration:
    AirPort Utility > Manual Setup > Wireless tab
    Wireless Mode = Extend a wireless network" (Hold down the option key on your Mac if you do not see this choice appear when you click the selection box).
    Wireless Network Name = Same name as your Time Capsule Network
    Check mark next to "Allow wireless clients"
    Security = Same setting as your Time Capsule
    Password = Same password as your Time Capsule
    Confirm Password
    Update to save settings
    The AirPort Express can only "extend" what it "receives". Most users position it too far away from the main router and consequently, the Express extends a weak signal. Try a location that is about 1/2 to 2/3 the distance between the Time Capsule and the area that needs move coverage. Then experiment a bit to find the best signal.
    Post back on your results.

  • Airport express failing to extend wireless network

    Have got an airport extreme connected via ethernet to my Virgin Media hub (hub is in modem mode).  Also have an airport express to extend the wireless network.  Setup has been working perfectly for over a year, then this weekend, literally no settings have been changed, and airport express is giving me a status message of "This airport base station was unable to extend the wireless network. Make sure the wireless network you're trying to extend was setup and is working correctly, that you entered a matching wireless network password into this device and that this device is in range of the wireless network"
    I have reset to factory settings 3 times now and whilst it goes through the initial setup, i always get the same status message.  Front light is green. 
    The express version I'm using is the 2012 redesigned version, looks like a white Apple TV and it has the latest firmware.  I've tried configuring via my MBA, windows desktop pc (windows 7) and ipad, nothing works
    Any ideas?

    You have to think of the Express devices as matching pairs when you have one set up to create a wireless and the other to extend it. Here, I assume that you still have the extending Express set up to extend the network.
    Power off both AirPort Express devices. The power down order does not matter.
    Wait a minute
    Power up the main AirPort Express.....the one directly connected to the Virgin hub....and let it run a full minute
    Then, power up the extending Express
    Check the network and report on your results

  • Airport Express won't extend wireless network

    I think due to a fault my airport express wont extend my wireless network around my house , but it will allow for airplay ... is it possiple to extend my network using the express but with an eithernet cable rather than the wireless that is transmitted out of the express unit ??

    Is the other wireless router, that you are trying to extend, another AirPort or Time Capsule base station? If so, are both units 802.11n models? Finally, what is the rough distance between the units and are they located in the same room, different room, or different floor?

  • I play music on my hi fi via an airport express attached to my iMac. Since installing maverick the sound quality is terrible and I get frequent distortion, which never happened before. I have reset the airport express and reconfigure my wireless settings.

    I play music on my hi fi via an airport express attached to my iMac.
    Since installing maverick the sound quality is terrible and I get frequent distortion, which never happened before.
    I have reset the airport express and reconfigure my wireless settings. I have also used Ethernet on its own but still get the same sound problems.
    I would love to turn itunes sound off as you used to be able to do, but this I believe can't be done.
    Has anyone else been having the same types of problem, and better still has anyone got the answer?

    When the AirPort Express Base Station (AX) is connected by Ethernet, you will find an option in the AirPort Utility, labeled: Enable AirTunes over Ethernet on the Music pane. Just select this option to allow streaming iTunes via the AirPort's Ethernet port. You should also be able to disable the AX's wireless so that it shouldn't interfere with the nearby TC.

  • Using a Airport Express Base Station for wireless printing.

    Using a Airport Express Base Station for wireless printing. Got a new DSL router yesterday. Our old one we did not have password protected. The new one is. I can't figure out how to get the base station to connect with the new router.

    thanks for the reply,   I couldn't connect with the base station.  The solution (thank you apple genius bar) was to do a soft rest of the unit which allowed and ethernet connectiont to be established.  Took the genius bar gy about ten min (and 2 attempts) to get the base station reconfigured.  Got home and it worked like a charm.  Would have never known what he knew.  Thank you genius bar.  Thank you for taking time to respond.

  • Airport Express Ethernet WiFi bridging with 3rd-party wireless base?

    I want to use an Airport Express as a substitute for a very-long Ethernet cable. Essentially, I want to connect a device (say, a computer) to the AE using an Ethernet cable, have the AE connect to a base station (not an Apple device) via wireless, and reach the network (Internet) on the other side of the base.
    A diagram of the desired goal is at http://img.skitch.com/20091111-1j7a61eka32jqntm217wwg7d3g.jpg
    I'm baffled. Here is what I've done:
    -Reset the AE to factory defaults
    -Connected a laptop to the AE via the Ethernet cable. Turn off my wireless (to make sure I'm talking to the AE via wired connection; this confirms the AE Ethernet port is working.)
    -Configured the AE (via the Ethernet cable) in a variety of ways (see below), restarted it.
    (alternately)
    -Reset the AE to factory defaults
    -Connected a laptop to the AE via wireless (connecting to the default-named network the AE creates on factory default reset)
    -Configured the AE in a variety of ways, restarted it.
    (This essentially suggests the AE is fully functional and not failed; I'm successfully able to connect to and configure the AE after factory default reset either wired, or wirelessly.)
    I've tried various configuration attempts, but the one that seems to get closest - but still fails the goal is this:
    -On "Airport / Wireless" tab: Join Wireless Network
    --(I've entered my SSID for my network in the Wireless Network name field)
    --(I've selected WEP 128 for security. I don't think I should be using WDS, given what I've seen elsewhere about WDS only working with an Apple Extreme.)
    --(Of course, I've confirmed the passwords match)
    -On "Internet / Internet Connection", the "Connect using" dropdown is disabled / greyed. This appears to only be enabled when I select "Participate in a WDS network" in the Wireless tab - which (as I said) I don't think I can use.
    -On "Internet / Internet Connection", the Configure IPv4 is set to use DHCP
    On restart, the AE successfully starts - it get's its IP address, the FIOS base station sees the device and lists it as online, and I can transmit audio successfully from iTunes to the stereo via the AE.
    BUT, configured this way, the Ethernet port is not providing network connectivity to the device attached to the AE via the Ethernet cable -- the same Ethernet cable that was moments ago letting me talk to the AE to configure it is now not active. When I attach my MacBook to this cable and open System Preferences and look at the Ethernet connection, it shows as not even having a cable plugged in; there's no Ethernet link / carrier present. (Until I do a Factory Reset on the AE, after which it works fine again.)
    Note: My AE is about 2-3 years old. I initially / previously had this configuration working just fine after I first installed the AE (after much pain, I recall). But I recently had Verizon installed, and in the process they put in a new base station. I seem to not be able to re-create the configuration I had that was working before.
    Note 2: I'm attempting to use the wireless base station supplied by Verizon FIOS, which supports a ton of connectivity options - though it doesn't list (and therefore I'm assuming doesn't do) Apple's WDS.
    Note 3: When I had it working before, I could have sworn the AE was also acting as a wireless base station that I could see in my available wireless networks listings, and was able to connect to the Internet wirelessly through it - as if it was a repeater of some kind. This isn't crucial; but it could be helpful in diagnosis.
    Note 4: I think I may have previously had the AE connecting via another device: I also have a Netgear WG602v2 that was connected BaseRouter---Netgear((( ))) AE---Device (where --- is an Ethernet wire, and ((())) is a wireless link). HOWEVER, I can't be sure this is how it was working; this may have been a relic from attempts to get it working originally several years ago. It is not essential.
    What am I missing?

    It sounds like you have an older 802.11 b/g AirPort Express, which as Duane mentions will not function as you would like.
    The newer AirPort Express 802.11n has a function called ProxySTA which allows the device to join (according to the attached article) virtually any wireless network with an option to "enable ethernet clients".
    While it is not possible to know whether any wireless network will be compatible with this feature, it has worked on a 2Wire and Netgear router that I've tried. Haven't tried Verizon Fios, so I can't assure you that this will work as you desire.
    http://www.macworld.com/article/132754/2008/03/express11n.html
    Another option might be to use a pair of ethernet powerline apapters, providing that everything is on the same master electrical circuit. In general, I've found the adapters to be more reliable and better performing than wireless, but of course, your mileage may vary. Post back if you need more info on this option.

Maybe you are looking for