Airport Express w/Ethernet Network

Hi all!
Is it possible to use the AX to connect to an ethernet network and stream audio? I've tried turning off the radio and using the bridge mode...the AX will appear in the Airport Utility for a couple of minutes, then disappear. I've also tried the roaming setup in a wireless configuration with the same result. The only configuration where I can maintain a connection with the utility is in join a wireless network mode.
Any suggestions?? Basically, I just want to use the ethernet network and avoid wireless.

Apple's instructions to "extend a wireless network" using wireless only are in the link below. Although the illustration pictures a 2nd AirPort Extreme, the setup for an AirPort Express is exactly the same.
http://support.apple.com/kb/HT4259
The Ethernet port is automatically enabled in this type of configuration to allow Ethernet devices to connect. If you need more than one Ethernet connection, you can add an Ethernet switch to the AirPort Express to create more connection capabilities.

Similar Messages

Airport Express via Ethernet to Extend Network

I am trying to have my Airport Express extend the network created by my Time Capsule by plugging ethernet into the AE so I can have the full signal (instead of wirelessly extending the network and degrading the signal). When I plug the AE into the wall with the ethernet already plugged into it, it goes green but then I lose visibility via Airport Utility to both the AE and the TC.
Does anyone have an idea of what I am doing wrong?
Thanks.

First verify that you have a good ethernet connection to the Time Capsule by turning off the wireless on a computer and connecting it to the ethernet wall jack. Make sure that you can get a good Internet connection on the computer.
Then, please check your settings on the AirPort Express using AirPort Utility-Manual Setup. They should look like this:
Click the Base Station tab below the Advanced (gear) icon
Name your device, establish a device password and adjust Time Zone settings
Click the Wireless tab below the Advanced (gear) icon
Wireless Mode = Create a wireless network
Wireless Network Name = Same name as your Time Capsule network
Radio Mode = 802.11n (802.11b/g compatible) a good choice. Otherwise, your choice
Channel = Automatic
Wireless Security = Same setting as the Time Capsule network
Wireless Password = Same password as the Time Capsule network
Click the Internet icon
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Update to save settings and restart.
Then power down the entire network. Start the modem first, then Time Capsule, then AirPort Express, then your devices.
Message was edited by: Bob Timmons

Connecting to Airport Express via Ethernet Cable

Dear Apple Support Community,
My setup at home is such that all my devices are in such close proximity to the Airport Express, and therefore I connect everything to the Airport Express via ethernet cables (NAS, Apple TV, PS 3).
The final step in my network setup would be to connect my Macbook to the Airport Express to connect to the internet using the Ethernet Cables, instead of using the wireless connection - because my Macbook is positioned right next to the Airport Express.
However, I am struggling to get the Macbook to connect to the Internet via the Ethernet Cable through the airport express. Is there a special way to set this up if this can be done. I know Wireless would be the answer, but the problem is, when I download movies etc, I write the files directly onto the NAS which happens a lot quicker than doing so via WiFi.
I hope the above question makes sense.
Thanks in advance for any feedback.
Regards
ST

Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire

AirPort Express Extend Wireless Networks (Multiple)

I've got an AirPort Extreme with these wireless networks:
AirPort Network
AirPort Network 5GHz
AirPort Guest Network
I've also got an AirPort Express which I would like to extend these wireless networks with (at least the first two), however the settings only allow me to select one of these wireless network.
I considered connecting the two AirPorts via ethernet, but then thought the two wireless networks would likely clash?
If anyone could advice me as to what I should do, that would be perfect, many thanks.

I've also got an AirPort Express which I would like to extend these wireless networks with (at least the first two), however the settings only allow me to select one of these wireless network.
If you have a "new" AirPort Express with dual band wireless capability, it will both bands using wireless only if you use the same wireless network name for both the 2.4 GHz and 5 GHz network on the main AirPort Extreme.
The Guest Network cannot be extended.
If you do have the option to connect the AirPort Express using Ethernet, it can certainly be configured to provide more wireless coverage that way. The networks will not "clash".

I'm trying to add my airport express to my network. The airport utility shows a message that its gathering info about my network then suddenly an unexpected error message appears. Why is that?

i'm trying to add my airport express to my network. The airport utility shows a message that its gathering info about my network then suddenly an unexpected error message appears. Why is that?

Until Bob Timmons gets back to you, first decide what you would like the Express to do. I understand you want it for AirPlay remote speakers, which you can certainly do.
I am assuming that you are not using an Apple AirPort router; if that's not the case stop here and let me know.
If your existing router is not an Apple AirPort Base Station, the Express:
can "join" an existing wireless network as a client, for the sole purpose of streaming music. If that's what you want to do, do not connect it to your router with an Ethernet cable.
can "extend" an existing wired network to serve as an additional wireless access point, which can also stream music. If that's what you want to do, connect its WAN port to an available LAN port on your router using an Ethernet cable.
Then, "hard reset" the Express according to the instructions below, and configure it. The prompts should be self-explanatory. If you run into trouble, describe which of the above two configurations you decided upon, and the point at which you're getting the "unexpected problem".
To "hard reset" an AirPort Base Station: make sure it's powered up, then gently press and hold its tiny reset button. Don't apply any more force than required to feel a tactile click. Keep it depressed for five to ten seconds, long enough for its LED to flash amber rapidly. Release the reset button. Then, the LED will glow amber steadily for about a minute. Then, it will flash amber, slowly, about once every second or two, waiting for you to configure it with AirPort Utility.

Question re AEBS Connected to Airport Express via Ethernet

If I have an AEBS that is being used to extend the range of my wireless network, if I connect an Airport Express via Ethernet to this AEBS for purposes of itunes airtunes will this work and will the wireless network remain wireless-n?

Yes, it will.
You also have the option of (a) completely turning off the radio on the Airport Express or (b) leaving it on, and using it to create a b/g point of access to your LAN thus allowing you to run the AEBSn in n-only mode for your n-capable wireless clients.

Connecting aiport extreme and airport express via ethernet cable ?

Is it possible to connect an airport extreme to an airport express via ethernet cable, I ask because I want to expand the range of my wifi network to the basement of my house, the floors are really thick concrete so I installed some ethernet cable runs, I hope somebody can help me, thank you.

+How do I do it ? Do I connect the modem to the airport extreme and then run the ethernet cable from one of the extreme's ethernet ports to the express ethernet on the basememt and a second cable from another of the extreme's ethernet connectors to the express on the second floor+
Yes, this is exactly correct.
To configure each AirPort Express (AX)
Open AirPort Utility, click Manual Setup
Click the Base Station tab below the icons to name your device, assign a device password and adjust time zone settings. Give each Express a separate name so you can identify then easily.
Click the Wireless tab
Wireless Mode...Create a Wireless Network
Wireless Network Name...Exact same name as your AirPort Extreme network
Radio Mode 802.11n (802.11b/g compatible) if you want to use 2.4 GHz
Channel...Automatic
Wireless Security...Exact same setting as your AirPort Extreme network
Wireless Password....Exact same setting as your AirPort Extreme network
Click the Internet icon
Change the Connection Sharing setting at the bottom to "Off (Bridge Mode)"
Click Update at the lower right and the AirPort Express will restart in 20-30 seconds
I think it is easier to configure each AirPort Express with AirPort Utility by temporarily connecting it to your computer with a short ethernet cable. Once you have saved the configuration, you can move the Express to the location that you need.
Please post back on your progress.

Connecting Two Airport Express Via Ethernet

I have a unique situation in which I would like to connect two airport express via ethernet. Here is the situation: I can connect the first AX directly to the internet and set up a WDS for the second AX. Unfortunately, the second AX signal does not reach where I need it to go. I can run an ethernet cable between the two. Is this setting valid for a WDS? Or does the WDS have to be wireless? If I can set up the WDS using an ethernet, will the relay AX broadcast the internet wirelessly then?
Are there any specific settings I should know about?
Any help would be great.
Thanks in advance,
Debbie

I currently have an old snow basestation at this location. Can I plug an ethernet cable into it and connect it to the AX?
Yes that will work.
My understanding was that the older basestation could not do this?
I think you have it confused with extending a network wirelessly. That is not possible with the snow AirPort base station (ABS).

AirPort Express over Ethernet lost the connection

I have an AirPort Express device. It's works well, if I connect it over WLAN. If I connect the AirPort Express over Ethernet via cable, then after about 15 minutes, I lost the connection between my PC and the AirPort Express.
Does I have to change settings in my router?

then when I try to switch it to extending
That is not the correct setting to use.
"Extending" is only used when an AirPort connects using a wireless connection to another AirPort router.
When the AirPort connects using Ethernet, you have to use the "Create a wireless network" setting.
It might be a lot easier if you simply start all over again and let the configuration "wizard" do most of the work for you. All that you really have to do is name the network, name the Express, enter the password and click Next. Everything else is handled by the configuration utility.
Post back if you are not sure how to do this.

HT1515 I'm getting poor performance from my apple TV, will plugging in my airport express via ethernet to apple tv increase its performance (poor wi-fi signal)

I'm getting poor performance from my apple TV, will plugging in my airport express via ethernet to apple tv increase its performance (poor wi-fi signal)

Yes, though it is less ideal than what I suggested earlier. You would need to place your AirPort Express in a location approximately midway between your AirPort Extreme Base Station and the TV. Then, using AirPort Utility, configure it to "extend a wireless network".
It may help. Bear in mind the signal thus "extended" by the Express can only be as good as the signal it can receive from the Extreme. That is the reason for selecting its appoximate midway location.
Read about it here: http://support.apple.com/kb/HT4145
Scroll down to "Wirelessly Extended Network (802.11n)" for a picture.
This solution requires an all-Apple wireless network. No third party stuff.
You mentioned using Ethernet. That would be a better idea. Scroll down to "Roaming Network (Ethernet-connected Wi-Fi base stations)" for a picture. In your case, the longer the Ethernet cable - hence the closer you can move the Express to the TV - the better

How do I remove an unwanted Airport Express from my network?

I have been using a Time Capsule for several years. I am having trouble backing up to my Time Capsule. I have discovered an unknown Airport Express in my network. I've changed networks, added passwords to the network, etc. How do I remove this unwanted Airport Express from my network? I think he is wreaking havoc with my system!! Help...

Maybe this is an issue I should consult my ISP about??
No question about that. If you can "see" Travis's device, then he can likely "see" your Time Capsule.
I'm just concerned that whomever the APExpress belongs to could be changing settings on my computer or Time Capsule that would cause the issues with me not being able to backup.
Make sure that you have a Time Capsule base station password. Unless a user has that password, they might be able to "see" your Time Capsule, but they cannot access any of the data on the Time Capsule or change the settings.
Open AirPort Utility, click on the Time Capsule and click Manual Setup
Then, click the Time Capsule tab below the icons to see the device name and password for your device. Make sure that you have entered the password and confirmed. Click Update if you have made any changes.
The message I get is "The backup was not performed because an error occurred while copying files to the backup disk. The problem may be temporary. Try again later to back up. If the problem persists, use Disk Utility to repair your backup disk."
I am not sure what this error means, because I cannot duplicate it here to test.
If it were me, I would try this "fix".
http://pondini.org/TM/A5b.html

How do I setup Airport express with ethernet connection to my modem?

Hi there - hoping to get some helpg as I'm having challnges setting up my Airport express via ethernet cable connection directly to my router. It will setup wirelessly no problem, but I occasionally get dropouts when streaming music and I'm hoping to remedy that with a direct cable connection. I know I have to change some settings in my airport utility, but haven't had any luck getting it right.
Here is my setups if it helps:
Airport express, 1st generation, model A1264
Cisco router (provided by my intenet provider)
Macbook Air, running 10.8.5
Airport utility version 6.3.1
Thanks!
Phil

Unfortunately, you are getting incorrect advice here. Might be a good idea to start a new post, since the original thread is long out of date.
First, please confirm that you have a compatible Express with the AirPort Extreme. This would be either the current A1392 version.....or the previous A1264 version.
Next, we need to confirm "how' you want to extend, since you do not mention this in your post.
Are you planning to "extend" by connecting the AirPort Express to the AirPort Extreme using a permanent, wired Ethernet connection (highly recommended).....or.....are you trying to "extend" by having the Express try to connect wirelessly to the AirPort Extreme?

Can't connect Airport Express wirelessly to network so that AirTunes and internet are available simultaneously

I can't connect Airport Express wirelessly to network so that AirTunes and internet are available simultaneously. My old AE allowed this but can't make the new one work that way.

In your instructions, you say to use the same encryption type as the router has set up. well, I am using the WEP 64 bit encryption and the Airport Utility does not have this...it has 40 bit. Is this a problem, or do I have to be using a the same type of encrytion ?
WEP is available in either 40 or 104-bit, but is usually "advertised" as either 64- or 128-bit respectively. For example, 64-bit WEP uses a 40 bit key (also known as WEP-40), which is concatenated with a 24-bit initialization vector (IV) to form the 64-bit RC4 traffic key. So, WEP 64 on the Linksys & 40-bit is equivalent.
What concerns me more is the loss of bandwidth performance you are experiencing when connecting the AX. When the AX is configured as a wireless client it is acting just like any other wireless devices (computer, laptop, printer, etc.) and not like another router. This should cause little or no bandwidth loss. True the more secure the wireless encryption used WPA2 vs. WEP, the more overhead is required for security, but the differences you are seeing seem excessive.
It is very possible that you may have some form of Wi-Fi interference in the immediate area that is preventing your Linksys from providing a good clean signal.
I suggest you perform a simple site survey, using utilities like the following to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible:
For Macs:
o MacStumbler
o iStumbler, or
For PCs:
o NetStumbler

15" MacBook Pro randomly loses connection to my AirPort Express wi-fi network.

My 15" MacBook Pro randomly loses connection to my AirPort Express wi-fi network. I have to switch off wi-fi on my Mac then switch on again to reconnect. Any reason why this random occurrence keeps happening which never happened before? Any solutions and fixes would also be welcomed.
Jazz

In the airport utility, you can alter the radio modes... and change the channels from automatic to a manual one.
Hold down the Option key, and click on your wifi icon, it will tell you what channels are currently being used on your OSX.

Airport Express: Extend a network and do Airtunes at the same time?

Hi, I'm trying to organize the people in my apartment building to share an internet connection wirelessly.
The connection is originating from a friend's apartment; he has a Linksys router, probably "g" flavor.
We're going to put one Airport Express in a neighbor's apartment to extend that.
I have an Airport Express connected to my stereo which I use only for Airtunes.
So I'm wondering: can I connect my Airport Express to this network and extend it and ALSO use it for Airtunes?
Also: Can I prevent my neighbors from seeing my Airport Express for Airtunes purposes? IE, I don't want my stereo to show up in the "multiple speakers" drop down of iTunes for other people connecting to the network...
Hope there's a way to work this out...

can I connect my Airport Express to this network and extend it and ALSO use it for Airtunes?
In order to extend the wireless range of the Linksys router, you would have to configure your AX and the Linksys in a Wireless Distribution System (WDS). Unfortunately, very few non-AirPort router are WDS-compatible. The few Linksys models that are reported to be compatible are the WRT54G & WRT54GS.
If you can create a WDS, streaming iTunes should not be a problem.
Also: Can I prevent my neighbors from seeing my Airport Express for Airtunes purposes? IE, I don't want my stereo to show up in the "multiple speakers" drop down of iTunes for other people connecting to the network...
No, but you can establish an iTunes Speaker password so they would not be able to stream to it.

Airport Express w/Ethernet Network

Similar Messages

Maybe you are looking for