Airport Express + WD Ethernet drive

Hi, I've been googling that for the past two hours and found nothing in regards to my question:
Will Airport Express work detect my WD Ethernet drive? Will I be able to see it as a normal network drive?
Best, Oskar

Yes, that is exactly my setup :
Router--+---Airport Express------Wifi-----Powerbook
+---WD Ethernet disk
+---iBook
My PB accesses wirelessly to the drive, exactly like the iBook (Ethernet)
It is not very fast, but it works...

Similar Messages

Connecting to Airport Express via Ethernet Cable

Dear Apple Support Community,
My setup at home is such that all my devices are in such close proximity to the Airport Express, and therefore I connect everything to the Airport Express via ethernet cables (NAS, Apple TV, PS 3).
The final step in my network setup would be to connect my Macbook to the Airport Express to connect to the internet using the Ethernet Cables, instead of using the wireless connection - because my Macbook is positioned right next to the Airport Express.
However, I am struggling to get the Macbook to connect to the Internet via the Ethernet Cable through the airport express. Is there a special way to set this up if this can be done. I know Wireless would be the answer, but the problem is, when I download movies etc, I write the files directly onto the NAS which happens a lot quicker than doing so via WiFi.
I hope the above question makes sense.
Thanks in advance for any feedback.
Regards
ST

Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire

How do I setup Airport express with ethernet connection to my modem?

Hi there - hoping to get some helpg as I'm having challnges setting up my Airport express via ethernet cable connection directly to my router. It will setup wirelessly no problem, but I occasionally get dropouts when streaming music and I'm hoping to remedy that with a direct cable connection. I know I have to change some settings in my airport utility, but haven't had any luck getting it right.
Here is my setups if it helps:
Airport express, 1st generation, model A1264
Cisco router (provided by my intenet provider)
Macbook Air, running 10.8.5
Airport utility version 6.3.1
Thanks!
Phil

Unfortunately, you are getting incorrect advice here. Might be a good idea to start a new post, since the original thread is long out of date.
First, please confirm that you have a compatible Express with the AirPort Extreme. This would be either the current A1392 version.....or the previous A1264 version.
Next, we need to confirm "how' you want to extend, since you do not mention this in your post.
Are you planning to "extend" by connecting the AirPort Express to the AirPort Extreme using a permanent, wired Ethernet connection (highly recommended).....or.....are you trying to "extend" by having the Express try to connect wirelessly to the AirPort Extreme?

Question re AEBS Connected to Airport Express via Ethernet

If I have an AEBS that is being used to extend the range of my wireless network, if I connect an Airport Express via Ethernet to this AEBS for purposes of itunes airtunes will this work and will the wireless network remain wireless-n?

Yes, it will.
You also have the option of (a) completely turning off the radio on the Airport Express or (b) leaving it on, and using it to create a b/g point of access to your LAN thus allowing you to run the AEBSn in n-only mode for your n-capable wireless clients.

Connecting aiport extreme and airport express via ethernet cable ?

Is it possible to connect an airport extreme to an airport express via ethernet cable, I ask because I want to expand the range of my wifi network to the basement of my house, the floors are really thick concrete so I installed some ethernet cable runs, I hope somebody can help me, thank you.

+How do I do it ? Do I connect the modem to the airport extreme and then run the ethernet cable from one of the extreme's ethernet ports to the express ethernet on the basememt and a second cable from another of the extreme's ethernet connectors to the express on the second floor+
Yes, this is exactly correct.
To configure each AirPort Express (AX)
Open AirPort Utility, click Manual Setup
Click the Base Station tab below the icons to name your device, assign a device password and adjust time zone settings. Give each Express a separate name so you can identify then easily.
Click the Wireless tab
Wireless Mode...Create a Wireless Network
Wireless Network Name...Exact same name as your AirPort Extreme network
Radio Mode 802.11n (802.11b/g compatible) if you want to use 2.4 GHz
Channel...Automatic
Wireless Security...Exact same setting as your AirPort Extreme network
Wireless Password....Exact same setting as your AirPort Extreme network
Click the Internet icon
Change the Connection Sharing setting at the bottom to "Off (Bridge Mode)"
Click Update at the lower right and the AirPort Express will restart in 20-30 seconds
I think it is easier to configure each AirPort Express with AirPort Utility by temporarily connecting it to your computer with a short ethernet cable. Once you have saved the configuration, you can move the Express to the location that you need.
Please post back on your progress.

Connecting Two Airport Express Via Ethernet

I have a unique situation in which I would like to connect two airport express via ethernet. Here is the situation: I can connect the first AX directly to the internet and set up a WDS for the second AX. Unfortunately, the second AX signal does not reach where I need it to go. I can run an ethernet cable between the two. Is this setting valid for a WDS? Or does the WDS have to be wireless? If I can set up the WDS using an ethernet, will the relay AX broadcast the internet wirelessly then?
Are there any specific settings I should know about?
Any help would be great.
Thanks in advance,
Debbie

I currently have an old snow basestation at this location. Can I plug an ethernet cable into it and connect it to the AX?
Yes that will work.
My understanding was that the older basestation could not do this?
I think you have it confused with extending a network wirelessly. That is not possible with the snow AirPort base station (ABS).

AirPort Express over Ethernet lost the connection

I have an AirPort Express device. It's works well, if I connect it over WLAN. If I connect the AirPort Express over Ethernet via cable, then after about 15 minutes, I lost the connection between my PC and the AirPort Express.
Does I have to change settings in my router?

then when I try to switch it to extending
That is not the correct setting to use.
"Extending" is only used when an AirPort connects using a wireless connection to another AirPort router.
When the AirPort connects using Ethernet, you have to use the "Create a wireless network" setting.
It might be a lot easier if you simply start all over again and let the configuration "wizard" do most of the work for you. All that you really have to do is name the network, name the Express, enter the password and click Next. Everything else is handled by the configuration utility.
Post back if you are not sure how to do this.

HT1515 I'm getting poor performance from my apple TV, will plugging in my airport express via ethernet to apple tv increase its performance (poor wi-fi signal)

I'm getting poor performance from my apple TV, will plugging in my airport express via ethernet to apple tv increase its performance (poor wi-fi signal)

Yes, though it is less ideal than what I suggested earlier. You would need to place your AirPort Express in a location approximately midway between your AirPort Extreme Base Station and the TV. Then, using AirPort Utility, configure it to "extend a wireless network".
It may help. Bear in mind the signal thus "extended" by the Express can only be as good as the signal it can receive from the Extreme. That is the reason for selecting its appoximate midway location.
Read about it here: http://support.apple.com/kb/HT4145
Scroll down to "Wirelessly Extended Network (802.11n)" for a picture.
This solution requires an all-Apple wireless network. No third party stuff.
You mentioned using Ethernet. That would be a better idea. Scroll down to "Roaming Network (Ethernet-connected Wi-Fi base stations)" for a picture. In your case, the longer the Ethernet cable - hence the closer you can move the Express to the TV - the better

Trying to set up Airport Express with Ethernet Powerline adapters

Hello,
Having some problems trying to set up my Airport Express with Netgear ethernet powerline adapters.
I want to set up as follows:
Wireless Belkin router --- powerline <---> powerline --- airport express --- home stereo system
The problem I have is that I can connect the airport x in client mode & wirelessly play music using airtunes (until the sound breaks up) but itunes does not find the airport x when connected via the powerlines.
I have airport admin utility configured as follows:
Airport tab:
Wireless mode: create a wireless network
Wireless network name: same as my wireless router SSID
Allow this network to be extended: unticked
radio mode: 802.11n (802.11b/g compatible)
Channel: automatic
Wireless Security: WPA/WPA2 personal (as per my router)
Wireless Password: as per my router
Verify Password: as per my router
Internet tab:
Connect using: ethernet
Connection sharing: off (bridge mode)
Music tab:
Enable Air Tunes ticket
no password set
In iTunes, I have home sharing on & share entire library selected with no password set.
Using OS 10.6.5 & Airport Express 7.5.2
I can ping the IP address of the airport express when connected via the powerlines but cannot select the speakers in iTunes (they are greyed out).
Any assistance would be appreciated....
Thanks

Hi,
Thanks for the quick response...
As suggested, I connected up the Airport X to the Belkin and plugged in a pair of headphones. It didn't work, still could not select the Airport X as speakers.
Dug out my old Netgear DG834G and connected that up in place of the Belkin - it worked. Next connected in the Netgear powerlines and it still worked.
So, the problem is the relatively new Belkin F7D4401 router.
Looks like I will have to find an alternative 802.11n...
Thanks for your help.
Regards
Simon

PC cannot see wireless Airport Express using Ethernet on D-LINK DIR-655 Router

This seems to be a recurring issue going way back, but I have yet to see a real solution posted.
I am using my Airport Express (APX) to stream music from the computers on my network to my stereo via Airplay. I have APX set up to wirelessly join my existing wireless network, which uses a D-Link DIR-655 router hooked to a Time Warner cable modem. I can succesfully connect all of my wireless devices via Airplay, through iTunes to my APX, including two laptops and an iPhone. However, my primary desktop PC, which does not have a wireless card is linked directly via ethernet cable to my D-Link router, and it is not able to see my APX. I can, however, see the Airport Express from my PC through my Airport Utility by directly typing in the IP address. Note that the APX set-up option to allow Ethernet clients is checked. I also noticed that my laptops will stop detecting the APX if I directly connect them to my D-Link router via Ethernet and turn off their wireless cards. They will resume detecting APX when I turn their wireless connections back on. So, bottom line, I am convinced that this is not a firewall problem. Although I have tried every conceivable setting of my D-Link router and APX, I am convinced it is either a wireless to ethernet communication issue, or some obscure setting on APX.. Any help would be appreciated.
Thanks,
Wayne

I think I found the fix based on reading some Apple TV forums where several people were having the same problem. Under Advanced Network settings in the D-Link setup, I just checked "Enable Multicast Streams" and that seemed to do the trick.

How to access an Airport Express USB hard drive from a PC?

I have a home network created by a new Airport Express base station (which replaced the previous AXBS that lasted 3 years and then died). Attached to its HSB port (with a USB hub) I have a WD USB disk and a Canon printer; I have another printer connected to one of the LAN ports. I have a mac attached to another of the LAN ports. Finally, my macbook connects to the network through the Airport. All peripheral items (disk, printers) work as they should from both macbook and the other mac.
I also have a PC with WI-FI that connects to the internet through the AXBS. The printers seem to work on the PC (with Bonjour for Windows installed), and I can access its disk from the macs, but I cannot access the WD AXBS hard drive from the PC.
The macbook and mac are running Snow Leopard and Leopard, respectively, and the PC is running XP SP2.
Can someone offer a suggestion for getting disk access to work from the PC? Windows or not, it shouldn't be this difficult.

Click here and follow the instructions, assuming you're using an AirPort Extreme base station. The AirPort Express base stations can't use USB hard and flash drives and will ignore any connected ones.
(49618)

ITunes 7.1 doesn't recognize Airport Express over ethernet

Running iTunes 7.1 on Windows XP desktop. Immediately after update, iTunes no longer can see my Airport Express as a remote speaker (Airtunes over Ethernet).
Airport Express has the latest updates. Airport Utility has no trouble recognizing it by name. It doesn't have a password on it. The Airport is happily providing wireless for my laptop. It is my only WiFi base station, because I have a small place. It's been dependable for over a year.
I'm truly bummed, because earlier today I got a Griffin AirClick USB, and it works like a charm. I was looking forward to using it with full-screen coverflow in 7.1.
iBook G4 and assorted Win & Linux boxes Mac OS X (10.4.8) iTunes is on an XP PC

The problem turns out to be an incompatibility with Bonjour for Windows. A post by "f00fighter" over in the "iTunes for Windows Upgrade Issues" forum solved it. I quote him below:
******Quote***********
Looks like this issue is due to an incompatibility between Bonjour for Windows and iTunes 7.1.0.59 for Windows (thanks toonz!)
To workaround the issue you can stop the Bonjour Service by going to Start \ Control Panel \ Administrative Tools \ Services, then highlight the Bonjour Service and stop it. You might also want to set the Startup status of the Bonjour Service to Manual (or Disabled) to prevent the service from starting automatically the next time you restart you PC.
Note - this is only a temporary fix, and turns off the Bonjour service...so don't do this if you have other applications that rely on the Bonjour Service. A fix from Apple is needed to truly "fix" this issue.
*****End Quote**********
iBook G4 and assorted boxen Mac OS X (10.4.8) iTunes is on an XP PC

Airport Express sloooow ethernet connection

Using an Airport Express base station as a wireless access port on my ethernet network. Configured the out of the box AE using the set up assistant over wireles form my laptop. Got the DHCP IP assigned in the reange of the router and made the connection. Email works but slow. Mounting a Google search page took 90 sec! Configuration: Netgear router with 8 port switch and T1 down service. Four of the router ports serve 4 locations of a business network. Second tier switches serve the puters in the 4 locations. The AE is ethernetted to one of these. So the path is: router-switch to distribution switch to AE wireless to laptop. Big problem pulling another cable direct from the router to the AE. Moving the AE to the router puts it 100 feet and 4 walls away, no bars on the rf signal strength indicator. Am I screwed or what?

problem due to firewall settings - resolved

Airport Express w/Ethernet Network

Hi all!
Is it possible to use the AX to connect to an ethernet network and stream audio? I've tried turning off the radio and using the bridge mode...the AX will appear in the Airport Utility for a couple of minutes, then disappear. I've also tried the roaming setup in a wireless configuration with the same result. The only configuration where I can maintain a connection with the utility is in join a wireless network mode.
Any suggestions?? Basically, I just want to use the ethernet network and avoid wireless.

Apple's instructions to "extend a wireless network" using wireless only are in the link below. Although the illustration pictures a 2nd AirPort Extreme, the setup for an AirPort Express is exactly the same.
http://support.apple.com/kb/HT4259
The Ethernet port is automatically enabled in this type of configuration to allow Ethernet devices to connect. If you need more than one Ethernet connection, you can add an Ethernet switch to the AirPort Express to create more connection capabilities.

Airport Express as ethernet - Airport bridge

I just bought an Express thinking it would be easy to configure to bridge my existing DSL -> wifi connection to a new wireless LAN.
Before I open the box I would like to know for sure that this will work. If the Express can't do this, I'll order a LinkSys WET54G bridge.
Our internet connection is via Airport as we live on our yacht. Our G4 connects to the net via a 24db antenna to the marina wifi network. The G4 is configured w/ Internet Sharing ON.
Our iBook connects to the net OK over ethernet via the G4 sharing. Now I'm trying to create a local wifi LAN on the boat so we can avoid CAT-5 strung around the boat.
Is the Airport Express the right solution?
Any suggestions mucho appreciated!
Steve

iFelix wrote "You can connect an Airport Express to the G4's ethernet port and configure to not distribute IP addresses and this will work."
Thanks heaps - got that. Will the wireless client[s] receive their IP addresses from the G4 DHCP server [Internet Sharing]?
I ask because all the Apple docs I've seen on configuring Extreme or Express as a bridge say that "all AirPort and Ethernet computers need to have IP addresses set manually and use the same subnet mask."
E.g., In Designing Airport Networks, p48,
Using the AirPort Extreme Base Station or AirPort Express as a Bridge
You can turn off the base station’s Internet sharing features (which provide IP addresses to AirPort computers using DHCP or NAT) to allow bridging between the network’s wireless and wired computers. With bridging turned on, AirPort computers have access to all services on the Ethernet network, and the base station does not provide Internet sharing services. Using the base station as a bridge can be a way to address incompatibilities between the base station’s Internet sharing features and your ISP’s connection method. To use the base station as a bridge, all AirPort and Ethernet computers need to have IP addresses set manually and use the same subnet mask.

Airport Express + WD Ethernet drive

Similar Messages

Maybe you are looking for