Airport express with old Netgear router together?

I just bought an Airport express because my older Netgear router may be causing issues with streaming movies on my Apple TV. (For some reason the movies cut off). Would it be better to throw out the old router and start anew with the Airport Express or use them both in conjunction?

If there is actually something amiss with your current Netgear router, then replacing it with the AirPort Express or any other wireless router would be in order. Otherwise, you would have to decide what you actual networking requirements are that you believe the AirPort Express Base Station (AX) would fulfill that the Netgear is not doing for you.
The Apple TV, especially the latest version, can work completely without the AirPort Express, and actually duplicates its AirPort Speaker feature.

Similar Messages

Airport express with wireless NetGear router

Hello everyone...
I received an Airport Express for Christmas. I was immediately able to set up a wireless network at the home I was visiting by plugging in the ethernet cable and a few simple set up steps. After bringing it home, I was able to set it up with the stereo in my bedroom to run iTunes throughout my apartment.
The problem is that I can't get the Airport Express to work through the wireless network already set up in my apartment. If I do the iTunes thing, I can't connect to the internet while it's playing--so it seems to be creating its own network but not connecting with the current wireless internet available in the room.
I did the full reset (unplugged the airport, pushed and held the reset button while plugging it back in until it flashed green three times). From reading other posts I understand that I do have a wireless router capable of handling the WDS (WGR614 v6) but for some reason I am unable to set it up!
Someone please help so i can stream iTunes and surf the net at the same time!

thanks for the link, however my router does not show up in the airport utility. I am not using an airport base station, I am using a Netgear as stated in the original question.
+> 1. Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.+
This I was able to do, obviously...
+>Open AirPort Utility. Select the main base station...+
There are no stations listed and I have tried clicking "other" and entering the IP address I believe my router is using, but to no avail.

Airport Express with D-Link router?

I bought an Airport Express with the specific purpose of connecting an old 1999 iMac to the internet (D-Link wireless router) via the ethernet port. I also thought I could use it to connect other ethernet devices such as my HD-DVD player.
I tried to configure the Express with my PowerBook to discover later in the instructions that the ethernet port is disabled when configuring the unit as wireless bridge/client. It sounds odd, becuase I can't understand the use of it, then. The range extender configuration which enables ethernet, apparently only works with an Airport base station. I admit I'm not very networking-savvy. Did I do something wrong? Am I understanding the instructions correctly?
Any help will be greatly appreciated.

Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your D-Link router can be extended wirelessly with the AirPort Express Base Station (AX).
The few that are known to work are:
o another Airport Express Base Station
o 802.11g Airport Extreme Base Station (AEBS)
o 802.11n AirPort Extreme Base Station (AEBSn)
o Linksys WRT54G or WRT54GS (not v5)
o Belkin F5D7230-4 and F5D7231
o BT Voyager 2091
o Netgear WGR614 v6
o Buffalo WGR-G54

Using airport express with a 2wire router

I just got Bellsouth DSL with a 2wire dsl modem that is also a wireless router.
It works fine, but I still want to use my airport express to listen to music.
I can't figure out how to do so, though I have tried various configurations
with the airport setup utility. Anyone have any ideas? How can I use
express with another wireless router?

Let's double-check your AirPort Express Base Station's (AX) settings ...
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing 2wire's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

Airport Express with wifi netgear in WDS

I have a wifi network provided by a Netgear router. Can I extend it in WDS with an Airport Express? In other words, does the airport express go in WDS with a Netgear wifi?

I have a wifi network provided by a Netgear router. Can I extend it in WDS with an Airport Express?
This is one of those things where you really won't know until you try. If you need to extend your Netgear router, you really should use a Netgear device to do it to insure compatibility.
The reason for this is that WDS was never adopted as an official standard, so the chances of one device working with another manufacturers device are open to question.
If you want to try the AirPort Express, it would be a good idea to understand the store's return policy in advance before you buy.
I would be extremely surprised if it worked with an Apple device, but I suppose anything is possible.
Please post on your results if you try the Apple product.

Using airport express with 3com modem/router

Hi all,
I have a 3COM modem/wifi router with serial code 3CRWE754G72-A.
I recently purchased a MacBook Pro and to my dismay the wifi does not work with my Router (I have all latest updates etc.). I have no idea why, but apple support say its cos my router is crap and they dont support 3rd party routers (they checked my MBP and found nothing wrong with it apparently, connects to apple base stations no probs)... there are loads of threads on this topic of incompatible wifi routers with the MBP in the MBP discussion area so I wont go into details on that.
My question is: is there any way the airport express could be of use? From what I understand usually you can use it to extend your wireless network by adding it as a client to the existing network. However I am suspicious if it will pickup on my 3com wireless network... my MBP doesnt so I wouldnt be surprised if this didnt either!! Is it somehow possible to disable the wifi on my 3com router and connect it directly via ethernet to an airport express, and use the airport express solely for createing the wifi network?
Any other suggestions welcome!

My question is: is there any way the airport express could be of use?
The only thing the AirPort Express (AX) could possibly do is join the wireless network created by that router as a client. This would only give you the ability to use the AX's USB printer port and AX's audio output. This would NOT give you the ability to use the AX's Ethernet port.
If your MacBook Pro can't join the wireless network provided by that device, the AX probably can't either.
The AX can not be used to extend the network provided by that device nor can the AX's Ethernet port be enabled to allow you to connect your MacBook Pro. Both of these require compatibility with Apple's WDS which that device does not have.

Airport Express with a Belkin router?

I've got an Airport Express b/g that I would like to set up to extend the range of my existing network and to use with Airtunes to play music from my computers through my main stereo. My network is currently using a Belkin router from my Comcast modem. Will the Express play nicely with the Belkin? The Express documentation only refers to Airport Extreme routers.
Thanks for any help

Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your Belkin router can be extended wirelessly with the AirPort Express Base Station (AX).
The few Belkin routers that have been known to work are:
F5D7230-4
F5D7231

Apple AirPort Express with Airtunes and Netgear WPN824v2 Router

I'm having some trouble getting the AirPort Express with Airtunes to connect to a Netgear WPN824v2 network.
Details:
- Router: Netgear RangeMax Wireless Router WPN824v2
- Wireless Network Security: WEP
- Computer: MacBook Pro
- OS: OS X 10.4.10
- AirPort card in computer: this works fine - no problems
- AirPort Express with Airtunes: the setup routine goes OK, but then the unit cannot connect to the wireless network; the light blinks amber.
Could the problem relate to the password (Hex versus ASCII) or perhaps WEP versus WPA?
Any / all suggestions welcome. Thanks.

sonicdubster, Welcome to the discussion area!
Are you following the directions in KB 302153, AirPort Express: How to join an existing wireless network in client mode?
Is the AirPort Express (AX) placed in an area where it can receive a good wireless signal from the Netgear?
Does the AX connect if you disable wireless encryption?
WPA (or WPA2) is much more secure and less troublesome than WEP. If all of your equipment supports WPA, I would switch to WPA.

Desktop PC with Airport Express connected to another router

Hi, I'm new to the wireless world. I have an exsisting wired network with wired connections. The router is a Belkin which also does wireless. I have another desktop computer which I cannot get wires run to so easily. My idea is to use my Airport express's ethernet port for this desktop and wirelessly connect the Airport express to the main router for internet services. Is this possible?
Thanks
Steve

Configure the Express as a bridge: join the wireless network, and set "connection sharing" to "off (bridge mode)". Under the Wireless tab, see if there's a box labeled "allow Ethernet clients".
If there is, check the box.
The "n" model Expresses that are capable of this were first sold in March, 2008. Earlier "b/g" only ones may be capable of this too; I just never had one so that's the reason for the qualifier.

HT1515 How do i get my old AirPort Express (7years old) to work with my new Time Capsule?

How do i get my old AirPort Express (7years old) to work with my new Time Capsule?

Does anyone at Apple have help for this sort of question - I too have an old printer (HP LaserJet 5MP) that I would like to keep using on my Mac. (Mac OSX 10.6.8).
I got it working by getting a USB cord that connects to it - but every once in a while it just stops working for weeks. The mac 'sees' it and it sends the data because the printer lights start blinking but then it just doesn't do anything. Is there no one who can tell me (and raterada) how to get some new life into these old printers. I would rather not add this (and a new toner cart) to the landfill just yet. . .

Airport express with hard-wired medem router?

hi there. i've got a hard-wired modem router to my mac and a pc. my mac however has got an airport card in it and i'm thinking of buying a usb wifi dongle thing (?) for the pc and use an airport express station to get wireless internet.
Can anyone please assure me that this set up would work:
lounge: iMac with aiport card.
bedroom upstairs: pc with usb wifi thing
living room: phone line plugged in modem router, modem router ethernet cabled to airport express plugged in socket on the wall. hi-fi plugged in airport express with stereo jack.
would i get wireless internet on both machines an my tunes wirellesly available on the hi-fi?
thanks for your patience!
also does anyone know whether i need to let my isp know that i'm intending to use wifi or will it work anyway?

With the AirPort Express Base Station (AX), configured as a "bridge and connected via Ethernet to your wired router, it will act like a Wireless Access Point (WAP). In this configuration, the wired router will continue to provide NAT & DHCP services for both the wired and wireless clients connected to it.
Your proposed network configuration is sound. The only issue I see may be the wireless range. The AX is advertised at 300' for 802.11b (11 Mbps), but building construction materials or other forms of Wi-Fi Interference may limit this range. The end result is that the wireless clients furthest away from the AX may experience weak or poor wireless performance.

AirPort Express with Air Tunes and wired router

Do any of you using AirPort Express with Air Tunes as a base station have it connected to a wired router, just as an added precaution?
thanks,
--h

As far as I know, AirPort Express w/tunes has a firewall, but a given router may offer more protection options than just a firewall. I'm wondering about security on the wired side of the connection, not the wireless side.
--h

Setting up Airport express with new Vista Computer?

I just bought a new computer with microsoft Vista. I have a netgear wireless router using WPA protection. I want to hook up an airport express as a client in another room where my stereo is. I had this working on my old XP computer but don't remember how I set it up because none of the discussions in the manual look anything like what I had. Does anyone know how to set this up?

Got it!!!! thanks to David NYC and tesserax. For other peoples benefit, change steps 1-5 on the above document procedure for Airport Admin Utility to the following:
1. Perform factory reset (situational)
2. Attach Airport Express via Ethernet to router.
3. Invoke your router software and view connected devices.
4. Identify Airport Express device id. It will be something like (192.168.1.3). You can tell which id is the airport express by looking for its MACD id on the list and comparing to the id printed on the Airport Express unit.
5. Open Airport Admin Utility.
6. Click Other.....
7. Enter the device id from #4 and password (this will be "public" if you reset to factory in step 1.)
8. Change settings to wireless (steps 6-13 of existing procedure)
Thanks to all who helped.

Trying to set up Airport Express with Ethernet Powerline adapters

Hello,
Having some problems trying to set up my Airport Express with Netgear ethernet powerline adapters.
I want to set up as follows:
Wireless Belkin router --- powerline <---> powerline --- airport express --- home stereo system
The problem I have is that I can connect the airport x in client mode & wirelessly play music using airtunes (until the sound breaks up) but itunes does not find the airport x when connected via the powerlines.
I have airport admin utility configured as follows:
Airport tab:
Wireless mode: create a wireless network
Wireless network name: same as my wireless router SSID
Allow this network to be extended: unticked
radio mode: 802.11n (802.11b/g compatible)
Channel: automatic
Wireless Security: WPA/WPA2 personal (as per my router)
Wireless Password: as per my router
Verify Password: as per my router
Internet tab:
Connect using: ethernet
Connection sharing: off (bridge mode)
Music tab:
Enable Air Tunes ticket
no password set
In iTunes, I have home sharing on & share entire library selected with no password set.
Using OS 10.6.5 & Airport Express 7.5.2
I can ping the IP address of the airport express when connected via the powerlines but cannot select the speakers in iTunes (they are greyed out).
Any assistance would be appreciated....
Thanks

Hi,
Thanks for the quick response...
As suggested, I connected up the Airport X to the Belkin and plugged in a pair of headphones. It didn't work, still could not select the Airport X as speakers.
Dug out my old Netgear DG834G and connected that up in place of the Belkin - it worked. Next connected in the Netgear powerlines and it still worked.
So, the problem is the relatively new Belkin F7D4401 router.
Looks like I will have to find an alternative 802.11n...
Thanks for your help.
Regards
Simon

Can't connect to Airport Express since upgrading my router.

I recently changed my router from an old Netgear 834 to a TP-Link W8961ND and now I keep losing the Airplay Speaker logo from my iphone4, ipad2, and itunes on my Windows 7 PC. When I unplug the AE and restart it connects but afer abour 30-40mins it disconnects and the only way to get it back is to unplug again. Is there some incompatibility with AE and the TP-Link router.

Same again, here...
TP-Link TD-W8961ND
Windows 7 PC
Mac-mini
iPad 2
iPhone 4s
2 Airport Expresses (1 old, 1 new)
I got the router and second AE (for another room) about a month ago to replace an aging 'g' Netgear (which, although dying occasionally connected to everything and the AE worked fine). Had the same problem from the start (only now properly investigating):
- Plug in either AE - light goes green
- Shows up in Airport Utility, speakers on all devices
- Fine for 30-40 mins
- Disappears from all devices and Airport Utility but light stays green
- Only way to resolve is to unplug and plug back in.
Strange. Pretty sure it's not the AE as I have one brand new and one old (which until we got the new router worked fine), and it's unlikely they'd both start exhibiting the same behaviour. So that leaves figuring out potential settings on the TP-Link.
And I don't think it's channel interference as (a) using iStumbler I see all the devices in the area are on either channel 1 or 11 - I've set the router to channel 6, and (b) other people are experiencing the same problem, and it's unlikely we'd all have the same conditions around us.
I'm not too sure about the various wireless settings - they're all a bit beyond me, but will continue with trial and error until something works... will let you know if I find anything.

Airport express with old Netgear router together?

Similar Messages

Maybe you are looking for