Airport express won't extend network via ethernet but shows GREEN (HELP!!)

I have the following routers setup up the same network and are working.
10.0.1.1 Airport Extreme (connected to hardline from IP)
10.0.1.2 Time Capsule 1 (extending network and providing internet connection to computer via ethernet)
10.0.1.3 Time Capsule 2 (extending network and providing internet connection to Xbox1)
10.0.1.4 Airport Express 1 (extending network and providing internet connection to Xbox2)
Not working correctly
10.0.1.43 Airport Express 2 (wanting to set this router up to extend network to plug into desktop)
The router seems to join the network fine and will show GREEN but doesn't show a similar IP address as the rest of the routers. It also doesn't provide any internet connection via ethernet to any computer, the network pref page says that it shows RED and that nothing is connected to the computer for internet but airport shows GREEN.
Reset the router multiple times, tried every which way of setting it up and no go. I also tried assigning it a IP and not using DHCP and gave it a 10.0.1.5 and still the same outcome.
Right now just at complete loss as to what to try next.

Sorry, the older version of the Express does not have the option to "extend a wireless network", which is the setting on the new Express that provides more wireless coverage and also enables the Ethernet port.
What you want to do can be done with a different setting..."participate in a WDS network" on both the Time Capsule and Express, but I am not recommending that you do this because WDS operates only in "g" wireless mode. Your Time Capsule would lose most of its performance in this setting and the network would slow down tremendously...defintely not what you want for gaming.
You'll have the best performance if you connect the PS3 directly to one of the Ethernet ports on the Time Capsule using an Ethernet cable. If it is not possible to run the cable, the next best performance option would be to use a pair of Ethernet powerline adapters to send the Ethernet signal over the existing AC wiring in your home.

Similar Messages

Airport Express won't extend network over LAN when plugged into a switch

I have several airport expresses (newest model) and an airport extreme.
Every room in my house is wired for ethernet. Those terminate in a closet and plug into a single switch. That switch then has a single cable that plugs into the airport extreme.
In different areas of the house, I've placed a few expresses to extended the wireless network. After several attempts, the express "hotspots" would only extend the extreme via wifi (offering no real advantage) even though they were plugged into the wall via ethernet.
For grins and giggles, I tried connecting the port directly into the airport extreme (bypassing the switch) and it started to send the traffic over the wired LAN.
Question is - why? I'd much rather everything go through the switch as the extreme has a limited amount of ports and I'd rather use for other things. Anyone had this experience before?
Thanks!

Sorry, the older version of the Express does not have the option to "extend a wireless network", which is the setting on the new Express that provides more wireless coverage and also enables the Ethernet port.
What you want to do can be done with a different setting..."participate in a WDS network" on both the Time Capsule and Express, but I am not recommending that you do this because WDS operates only in "g" wireless mode. Your Time Capsule would lose most of its performance in this setting and the network would slow down tremendously...defintely not what you want for gaming.
You'll have the best performance if you connect the PS3 directly to one of the Ethernet ports on the Time Capsule using an Ethernet cable. If it is not possible to run the cable, the next best performance option would be to use a pair of Ethernet powerline adapters to send the Ethernet signal over the existing AC wiring in your home.

AirPort Express won't extend network range

I spent 5 hours on the phone with three different apple reps changing every possible setting on the airport express that i wanted to use to extend the range of my existing network and even though AirPort utility said everything was set up right, the AX was only connected as a client. It was on the network, but not broadcasting ANY signal. This was at an office building with an AirPort Extreme as the base station. Both devices are brand new. 802.11n. I then took it home to see if it would extend the range of my home network which is set up using an AirPort Express as the base station. After trying every possible set up option there i was left with the same result. No broadcasting from the remote Express. It broadcasts when it's a base station, but not as a remote extender. What's the problem?!

I am going nuts too trying to configure my Airport Express to extend the range of my Airport Extreme. Nothing seems to work and I've been at this off and on for months. The Extreme works fine (it's an "n") but the Express (I think a "g") won't cooperate. And Apple has no current definitive step-by-step instructions that help at all. Does anyone out there have a solution? Shouldn't this just be plug-and-play with a few tweaks to the settings?

Airport Express Won't Extend Network

I have an AirPort Extreme and I am trying to use my AirPort Express to extend its network. For quite a while, it was working fine. Then, due to some interference issues, I had to change the channels on my AirPort Extreme. Since then, the AirPort Express flashes Amber. I have tried restoring it to its default settings from AirPort Utility, as well as the reset button while plugging it in. My computer detects it, renames it, and automatically chooses to extend the network from the Extreme, but when setup is finished, it just flashes Amber. What can I do?

Ii suggest that you run a few quick tests to try to begin to troubleshoot the issue.
Move the AirPort Express to the same room as the AirPort Extreme to reset and reconfigure the device again.
Do you get a green light that way?
If yes, then unplug and move the Express to a location that is no more than half the distance between the AirPort Extreme and the general are that needs more wireless coverage and test to see if the Express will work reliably at that location.
However, if you cannot get the AirPort Express to work when you configure it in the same room as the Airport Extreme.....and you have reset the AirPort Express several times, then it is time to start thinking about the possibilty that the Express is defective.
Please post back on your results, as it still may be necessary to use a good utility like WiFi Explorer to help analzye your wireless network connection quality and take a look at other sources that may be introducing wireless interference that is affecting your network.

HT4259 how to configure extended network via ethernet

how to configure an extended network via ethernet

I assume that the Express is new, so that it still has the factory default settings.
Connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the AirPort Express
Power up the Extreme and Express if they are not already powered up
Open Macintosh HD > Applications > Utiltities > AirPort Utility
Click on the tab in the upper left hand corner of the window that reads Other AirPort Base Stations (1)
Click on the AirPort Express xxxxxx
Wait a minute or two while AirPort Utility analyzes the network and then announces that the Express will be configured to extend your network
Enter a name for the AirPort Express and click Next
Wait 2-3 minutes while AirPort Utility configures the Express and the Express restarts
When you see the message that setup is complete, click Done
That's it.

My Airport Express won't extend range. How to set up?

My Airport Express won't extend the range of my Airport Extreme. How should I set it up to get it to work? Stuart

When the Express is configured to "extend" it is a wireless repeater.
"Adding Wi-Fi base stations when it is unnecessary
Speaks for itself
can reduce Wi-Fi throughput because the Wi-Fi network will require more data management overhead."
As will adding another computer, iPhone or any wireless device to the network, for that matter.
FWIW, I have run 4 AirPort Expresses all setup to "extend" and noticed nothing except faster Internet browsing and download speeds throughout the house.
IF...you can connect the AirPort Express to the AirPort Extreme using an Ethernet connection, that will provide better overall performance. That is the way any commercial network is designed, except on a much larger scale.

Airport Express won't extend Airport Extreme Network

I use an Airport Extreme (AE) to connect to the internet. I use an Airport Express (AX) to extend the network via a WDS network. Until recently all was fine.
Last week I updated the firmware for my AE. Since then my AX has not been acting as a WDS extension. I have tried several times tonight to make the AE and AX talk to each other in this fashion. I have reset the AX to factory defaults and reset the AE as well. So far, nothing works.
Thought the AX might have failed. However, the AX will connect to the AE network just fine. It just won't extend the network.
Any ideas will be most appreciated.
Thanks.

I have an Airport Extreme Base Station. I just bought an Airport Express to extend my network and connect a wired device in my living room to my network via the Ethernet port. The Airport Express obtains an IP address from the Airport Extreme but I can't seem to get out to the Internet ...at least via the Ethernet port. When I installed the Airport Express, I updated it to 7.3.1.
This sounds like a similar problem to the original post.

Cannot connect devices using Extend Network via Ethernet

Hi
I have been going nuts with this issue, and cannot seem to find any solutions. PLEASE HELP!
I have an Airport Extreme (pretty new and all up to date) connected to my modem. Everything works perfectly. The wi-fi is great, all devices can connect without any issues so nothing is wrong here. The Airport extreme is dishing out the IP addresses etc. The Airport extreme is in the lounge.
I purchased a new airport express yesterday. I put it in my study, far away from the lounge. I connected the airport extreme to the airport express using an ethernet cable. I plugged it in, and set it up to extend the wireless network via ethernet. I.e. it is set up in bridged mode and set up to 'create a wireless network' with identical name password etc. Everything is good. It reboots and the light is green. in the Airport utility everything shows up correctly.
Here is the problem., The second that any device (lets say iphone) moves from the lounge to the study, and tries to 'jump' to the stronger network provided by the express, it kills the ENTIRE network. The following happens:
1. The iphone loses wi-fi signal immediately. If I go into wi-fi settings, it sees my netwrok with FULL strength, but just remains in the 'spinning ball' state trying to connect. Seems to me that the express is unable to hand out an IP address or something.
2. If i open the airport utility on my Imac (in the study), the airport extreme has a yellow warning light and cannot be found via ethernet OR wi-fi. (The Imac is also Hard Wired from the Airport extreme in the lounge).
THe whole system requires a re-boot in order to work again.
If I re-boot the system, and leave a device near the airport express, it immediately receives signal, gets an IP address, and has an internet connection. Going back to the lounge causes no issues, it doesnt drop signal and still connects to the internet via the extreme. But as soon as I walk back into the study again - BOOM, everything drops.
I only purchased the new express because i was having EXACTLY the same issue with an older Airport extreme. No matter what I do, it just wont work via ethernet. I have tried all manner of settings. The ONLY setting that seems to work is to extend the wi-fi network. However, the rooms are too far apart, and this will require a third station in the middle, which i want to avoid (by the time the wifi network is extended across 3 decvices it is too slow).

Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try.

Airport Express can only extend network, not create new one. Why?

I am sharing a flat with some friends. The shared broadband router is placed in the living room. To strengthen the signal and make it easier for me to manage, I bought an Airport Express, connected it to the shared router with an ethernet cable and set up a wireless network of my own in my room. It was working fine, until recently we renewed our broadband contract. The router had been replaced by a new one (I don't know why) and the network configration had been changed. Since then I was not able to use my own network. In the Airport Utility display, the light of Airport Express is green, but the light of Internet is yellow, and the status is disconnected. I tried to change various other configuration on the Airport Express, and all in vain. Until I switched the network mode from 'Create a new wireless network' to 'Extend a wireless network', the Internet connection was finally back online. But this merely extends the existing network and not what I want. Why this happens? Why my Airport Express can only extend a network, not create one?

Here is the situation on my Airport Express.
If I choose to extend the existing wireless network, the Airport Utility shows like this:
If I set up a wireless network of my own, what I get in the Airport Utility is this:
See my problems here? The Airport Express does not show anything in amble, but the Internet complains that there is no connection.
This problem did not occur before the broadband was renewed and the rounter was replaced.

Use Airport Express Brick N to extend network via ethernet

I have the old brick-style Airport Express N model, which I'm currently using to extend the newer Airport Express hockey puck. The hockey puck is setup to with DHCP and creating the network. The brick is in setup to extend the network using DHCP and in Bridge Mode. When I plugin the Ethernet cable from the Ethernet port of the hockey puck to the brick, I lose all internet connectivity. I seem to recall reading some documentation that said the brick would support ethernet rather than just over-the-air. Thanks for your help!

My question is: can I connect the two via ethernet cable to the extending is happening over the air? I'm not sure the brick is capable of this?
It is possible to "extend" in two different ways:
1) Extend using a wireless connection between the AirPorts. Apple calls this "extend using wireless" during the setup. When you extend this way, about half of the potential speed on the network is lost.
2) Extend using a wired Ethernet connection between the AirPorts. Apple calls this "extend using Ethernet" during the setup. When you extend this way, full bandwidth on the network is maintained since there is no signal loss in a wire.
If you want to "extend using Ethernet", the 2nd Gen AirPort Express must be the "main" router, so you will need to reconfigure it for that purpose. The 1st Gen will also need to be reset back to default settings and reconfigured as well.
Once the 2nd Gen Express is working correctly as the main router, connect an Ethernet cable from the LAN <--> port on the 2nd Gen Express to the Ethernet port on the 1st Gen Express and use AirPort Utility for the setup.

Using airport express to extend network via ethernet socket

I have a wireless router set up which feeds my mac and tv (via a wired ethernet connection). I have also a pc which doesn't have wifi capability.
Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket? I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
Thanks

Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try.

Airport Express Won't Extend my Network

I've had my AirPort Express for around 3 months now and it was working fine and extending my network with my base station as the Apple Extreme just fine, until 2 weeks ago. Suddenly, it started flashing amber instead of green, and even though I reset it, disconnected it and re plugged it in, and placed it in another room, it didn't work, so I called Apple. Keep in mind that the whole time this is happening, the light for the Apple Extreme was working, and so was the wi-fi, just the Express which I use as an extender wasn't. I was on the phone for 2 hours with them and eventually they got it to work by resetting the Apple Extreme and setting it up as a completely new network, which was tedious and annoying, but it worked. Now, I have the same problem again, and I have tried the same steps I used before, and it still isn't working. Is there any way I can get it to work without having to reset the Apple Extreme?

yes, you can first do it with a short eth cable so you're still next to your extreme and then run the longer cable when you're ready to put it where you want it
before you connect the eth cord to the express, fully reset it
unplug express
hold in reset and keep holding it down while plugging power back in - only release reset when amber light flashes after 10-20s
now plug in the eth cable
your airport utility should auto see that you're trying to extend your extreme via your express on a wired connection

Airport Express won't extend wireless network

I think due to a fault my airport express wont extend my wireless network around my house , but it will allow for airplay ... is it possiple to extend my network using the express but with an eithernet cable rather than the wireless that is transmitted out of the express unit ??

Is the other wireless router, that you are trying to extend, another AirPort or Time Capsule base station? If so, are both units 802.11n models? Finally, what is the rough distance between the units and are they located in the same room, different room, or different floor?

Trying to extend network via ethernet

Trying to add another Extreme to our network to assist with the number of wireless clients on our existing Extreme. Trying to add the 2nd Extreme via Ethernet and extend the same network SSID and all other info.
After setting up and adding it shows that it is extending via wireless, and when connecting to the WAN or LAN ports it wants to take the entire network down.
Using 5th Gen Extreme. Airport Utility 6.2, and all devices have 7.6.3 firmware. Already have 2 Express units on the system extending the network wirelessly where we do not have Ethernet ran. Those have been working for over a year.
Any thoughts on what we are missing when setting this up where we can't plug another Extreme in via Ethernet? In the setup I don't see an option for extending via ethernet.....

Close AirPort Utility if it is open
Disconnect the Ethernet cable to the new AirPort Extreme
Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds and release. Allow a full minute for the AirPort to restart
Make sure that the Ethernet cable is connecting from a LAN <-> port on the "main" router to the WAN "O" port on the new AirPort
Click the AirPort icon at the top of the Mac's screen and wait a minute for the heading of New AirPort Base Station to appear
Just below that, click on the AirPort (an AirPort Express is pictured in the example)
AirPort Setup will open automatically and take a minute to analyze the network....then announce that the AirPort Extreme will be configured to "extend" your current network.
Enter a device name for the AirPort Extreme and click Next
AirPort Setup will take a minute to configure everything for you. When you see the message of Setup Complete, click Done
Test the network and report on your results

Airport Express Won't Join Network Anymore

I had my Airport Express set up in my house as a range extender for my Airport Extreme. It was working fine until I recently updated the Airport software (or firmware, I don't remember). Now the AP Express is blinking amber. I went through all the trouble shooting steps, including hard and factory reset. My Airport utulity (6.0) sees the AP Express, and it takes me through all the steps setting it up as a range extender for my basestation on my wireless network, but at the very last step it says there's an error connecting. When I connect via ethernet only it's yellow on the utility, with status saying there no valid IP address. Tried the same IP settings as my basestation, but no luck. It also says the wireless network can't be found.
Is this a software problem, or a hardware issue? I feel like I'm missing something simple. I would appreciate any help anyone can offer. Thanks!

Download and use Airport Utility 5.6
This was release the same day as 6.0 but 6.0 is quirky and exhibits strange behavior at times.
http://support.apple.com/kb/DL1482?viewlocale=en_US&locale=en_US
Do a Factory reset again and set it up using 5.6

Airport express won't extend network via ethernet but shows GREEN (HELP!!)

Similar Messages

Maybe you are looking for