Airport Express won't extend wireless network

I think due to a fault my airport express wont extend my wireless network around my house , but it will allow for airplay ... is it possiple to extend my network using the express but with an eithernet cable rather than the wireless that is transmitted out of the express unit ??

Is the other wireless router, that you are trying to extend, another AirPort or Time Capsule base station? If so, are both units 802.11n models? Finally, what is the rough distance between the units and are they located in the same room, different room, or different floor?

Similar Messages

Airport Express wouldn't extend wireless network

Am posting this in case it helps someone else. I have an Airport Extreme set up as a base station and couldn't get an Airport Express to "extend wireless network". I finally found a checkbox in the "Wireless" tab of the "Manually Configure" dialog box for the Extreme that says: "Allow this network to be extended". I could not find this referenced anywhere in Apple documentation, so you have to know to go and check this box. Apologies to the techies if this is a no-brainer, but I only found it by accident. Apple should include a brief paragraph in their wireless troubleshooting guide on extending your network.

When you configure the Express to "join a wireless network" it becomes part of the network so that you can stream AirTunes to the device or use a remote printer connected to the USB port, but it does not provide any additional wireless coverage in this type of configuration.
"Extend a wireless network" does the same thing as above, except the Express will also provide more wireless coverage in the area where it is located.

AirPort Express will not extend Wireless Network

Hello. My airport express will not extend my wireless network. It was green for about the first 4 hours and then I've had a flashing yellow light since that time. I've reset it a bunch of times and even have the AE in the same room as my AP Extreme. I complete the setup and then it continues to flash yellow. Can ayone give me a hand?

In the cases where the AirPort base stations would be interconnected by Ethernet you want to configure then for a roaming network, NOT an extended network. Apple uses the term "extended" when the base stations use wireless connection. Regardless of naming convention the end results is pretty much the same.
The link I provided should provide you with the necessary steps to set this type of network up.
If you need additional help, please start a new post as the solution for you will be different than the OPs. Thx!

Airport express can't extend wireless network

Airport express(A1264) can't extend wireless network. It seems that Airport express can't find my home Wi-Fi network. Amber light is blinking, and AirPort Utility of MacBook also can't find Airport express.
If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
It was successful only once, but all failed after that.
Is there solution for this problem?
[My system]
Time capsule 4th generation
Airport express 1st generation (A1264)
[Settings]
Time capsule (ethernet connected)
- Create a wireless network
- 802.11a/n - 802.11b/g/n (Automatic)
- 2.4GHz / 5GHz Channel (Autmatic)
- WPA2 Personal
Airport express
- Extend a wireless network
- WPA2 Personal
- 2.4GHz Wi-Fi network name and Password is set up

If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
Sorry, I misunderstood what you wanted to do.
Since you did tell us that you had the Express connected with an Ethernet cable, I assumed that was how you wanted to configure the Express.
But I want to extend a wireless network (not using ethernet)
Because Airport Express and Time Capsule cannot be connect via ethernet cable.
Follow the same setup as above....and do not connect an Ethernet cable.
Keep the Express near the Time Capsule for the setup. Once you have a green light, move the Express to a point that is about half way between the Time Capsule and area that needs more wireless coverage.
If you reset the Express several times and try the setup several times without success, I think you have to suspect a defective Express.

Airport express failing to extend wireless network

Have got an airport extreme connected via ethernet to my Virgin Media hub (hub is in modem mode). Also have an airport express to extend the wireless network. Setup has been working perfectly for over a year, then this weekend, literally no settings have been changed, and airport express is giving me a status message of "This airport base station was unable to extend the wireless network. Make sure the wireless network you're trying to extend was setup and is working correctly, that you entered a matching wireless network password into this device and that this device is in range of the wireless network"
I have reset to factory settings 3 times now and whilst it goes through the initial setup, i always get the same status message. Front light is green.
The express version I'm using is the 2012 redesigned version, looks like a white Apple TV and it has the latest firmware. I've tried configuring via my MBA, windows desktop pc (windows 7) and ipad, nothing works
Any ideas?

You have to think of the Express devices as matching pairs when you have one set up to create a wireless and the other to extend it. Here, I assume that you still have the extending Express set up to extend the network.
Power off both AirPort Express devices. The power down order does not matter.
Wait a minute
Power up the main AirPort Express.....the one directly connected to the Virgin hub....and let it run a full minute
Then, power up the extending Express
Check the network and report on your results

Airport Express used to extend wireless network from Linksys?

I've been asked if I can straighten out a wireless mess at a local church. They have a wireless network in their office (a seperate small building) using a linksys transmitter.
The church (a seperate building 50 yards away is where they want to extend the network to.
Currently, I can read the network there on whqat they have now but something is misconfigured and the manufacturer is being of little assistance.
Has anyone used an Apple Airport Express to extend a 3rd party wireless router? Ive decided it may just be worth the cost to dump the relay they have and simply buy an airport express.
Suggestions?

The Linksys WRT54G and WRT54GS (not latest versions v5) are the only 2 known Linksys routers compatible with Apple's WDS.
So if you are using one of those routers you should be able to do it.
If you are using a different router it probably will not work.

Airport Express wil not extend wireless network via ethernet

I need maximum bandwidth in a area with poor signal. No matter what I do, the AE will not extend my APEBS dual band via ethernet. It will alway connect wirlessly giving me half the speed. I have 1 main network to extend. I have tried to extend the 5 GHz wide channel as a seperate network but this wont work either.(but thats what I want really. Please help. I have been at this a couple days already and I need to figure it out before my return policy wears out. Thanks!

If you are connecting the Airport Express to your AirPort Extreme via ethernet, the AirPort Express should be configured as follows:
Open AirPort Utility, click Manual Setup
Click the Wireless tab just below the row of icons
Wireless Mode should be set to "Create a Wireless Network"
Wireless Network Name would be the exact name of the main network that the Extreme is creating, same security, password.
Radio Mode must be set the same as the main network on the Extreme
Channel should be set to be least 6 channels apart from the channel that the main network is using on the Extreme.
Click the Internet icon above and look for Connection Sharing at the bottom of the page. This should be set to "Off (Bridge Mode)".
Update to save settings.
For more info reference page 42. http://manuals.info.apple.com/enUS/Apple_AirPort_NetworksEarly2009.pdf

Airport Express Won't Extend my Network

I've had my AirPort Express for around 3 months now and it was working fine and extending my network with my base station as the Apple Extreme just fine, until 2 weeks ago. Suddenly, it started flashing amber instead of green, and even though I reset it, disconnected it and re plugged it in, and placed it in another room, it didn't work, so I called Apple. Keep in mind that the whole time this is happening, the light for the Apple Extreme was working, and so was the wi-fi, just the Express which I use as an extender wasn't. I was on the phone for 2 hours with them and eventually they got it to work by resetting the Apple Extreme and setting it up as a completely new network, which was tedious and annoying, but it worked. Now, I have the same problem again, and I have tried the same steps I used before, and it still isn't working. Is there any way I can get it to work without having to reset the Apple Extreme?

yes, you can first do it with a short eth cable so you're still next to your extreme and then run the longer cable when you're ready to put it where you want it
before you connect the eth cord to the express, fully reset it
unplug express
hold in reset and keep holding it down while plugging power back in - only release reset when amber light flashes after 10-20s
now plug in the eth cable
your airport utility should auto see that you're trying to extend your extreme via your express on a wired connection

Airport express won't extend wireless

Hello
Know there are countless of these out there already but would appreciate if someone knew this one. Since 2-3 weeks back my wireless set-up has not worked properly. Set-up;
ISP Router in bridge to a Airport Extreme, Extreme running DHCP and NAT.
I have two A1264 or first generation AEs
I have one A1392 or second generation AE
So this summer all three was extending the network and it all worked fine. Now I understand the A1264 cannot do that anymore (why?) but also the A1392 wont extend the wifi either. Currently I am using the A1264 as just connecting to wireless and the A1392 to extend, but the last part does not work. It just says unable to extend the network.
Still all three AEs are green and happy, I have tired re-booting and reconfiguring but nothing seems to get the A1392 to extend. is there some switch or option I could have forgotten?
Thanks in advance

Oh man this is so annoying.

Airport extreme won't extend wireless network

I have two airport extreme base stations (the 802.11n versions, both of them), both with the latest firmware. One is the main base station, connected to the cable modem. The second is set up to extend the network where the signal from the first is weak.
After working flawlessly for about 6 months, the second airport extreme, the one that extends the network, will not do anything but blink yellow. I have turned the power off and on, restored default settings through Airport Utility, and performed a hard reset. After the latter two, I am able to "see" the unit again, and configure it again to extend the network, but immediately after doing so it goes back to non-functioning blinking yellow signal.
Is this just likely a hardware problem so that I need to bring it in? Or is there something more I can try?
Many thanks.

Is this just likely a hardware problem so that I need to bring it in? Or is there something more I can try?
Before bringing it back I would suggest that you temporarily relocate the extending Extreme into the same room as the Extreme it is extending. Go ahead and reconfigure them for an extended network. This time does the extending Extreme provide you with a steady green status light?
If this is the case, you may find that just need to reposition the extending Extreme in a different location so that it is within a Signal-to-Noise Ratio (SNR) range greater than 25 dB. Let me know if you would like for me to provide you with step-by-step direction on how to calculate SNR jusing a Mac laptop.
The other thing would be to verify that there isn't some new form of Wi-Fi interference present that is preventing the extending base station from receiving a quality signal.

Airport Express won't extend Airport Extreme Network

I use an Airport Extreme (AE) to connect to the internet. I use an Airport Express (AX) to extend the network via a WDS network. Until recently all was fine.
Last week I updated the firmware for my AE. Since then my AX has not been acting as a WDS extension. I have tried several times tonight to make the AE and AX talk to each other in this fashion. I have reset the AX to factory defaults and reset the AE as well. So far, nothing works.
Thought the AX might have failed. However, the AX will connect to the AE network just fine. It just won't extend the network.
Any ideas will be most appreciated.
Thanks.

I have an Airport Extreme Base Station. I just bought an Airport Express to extend my network and connect a wired device in my living room to my network via the Ethernet port. The Airport Express obtains an IP address from the Airport Extreme but I can't seem to get out to the Internet ...at least via the Ethernet port. When I installed the Airport Express, I updated it to 7.3.1.
This sounds like a similar problem to the original post.

My Airport Express won't extend range. How to set up?

My Airport Express won't extend the range of my Airport Extreme. How should I set it up to get it to work? Stuart

When the Express is configured to "extend" it is a wireless repeater.
"Adding Wi-Fi base stations when it is unnecessary
Speaks for itself
can reduce Wi-Fi throughput because the Wi-Fi network will require more data management overhead."
As will adding another computer, iPhone or any wireless device to the network, for that matter.
FWIW, I have run 4 AirPort Expresses all setup to "extend" and noticed nothing except faster Internet browsing and download speeds throughout the house.
IF...you can connect the AirPort Express to the AirPort Extreme using an Ethernet connection, that will provide better overall performance. That is the way any commercial network is designed, except on a much larger scale.

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

How to add airport express to my current wireless network

Hi guys.
I have a dlink router (ac) configured as NAT and a friend of mine gave me an airport express (ac) to extend my current wireless network.
I believe that i should configure the airport express as bridge mode in order to mantain my current ip range.
I'm trying to configure the airport express but i can't even loggin to it.
The question.
Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
Thanks so much and any help would be really appreciated.
Regards.
Francisco.

Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
Unfortunately, the answer is that neither an AirPort Express nor an AirPort Extreme is compatible with a D-Link router....or any other 3rd party router for that matter.....if you are trying to have the the AirPort device extend the signal using wireless.
The AirPort Express can extend a signal from another Apple router.
'm trying to configure the airport express but i can't even loggin to it.
You may have received an older version of the Express that is not compatible with the newer Mac operating system that you are using.
Look for the model number of the Express on the side of the device.....hard to see in the faint print.....you may need a magnifying glass. If you see model A1084 or A1088, these older versions are no longer supported by Lion, Mountain Lion or Mavericks operating systems.
The workaround is that you must use a Mac that is running Leopard or Snow Leopard, or a PC to be able to administer the older versions of the AirPort Express models.

Adding Airport Express to D-Link wireless network

We have a D-Link wireless router given us by our ISP. I have an Xbox 360. I'd like to take one of our Airport Expresses, and connect the 360 via Ethernet cable to the Airport Express, while the Airport Express joins the D-Link's network, thus giving my 360 wireless internet.
We used to accomplish this using another Airport Express instead of the D-Link, but for our own reasons, we now need to use the D-Link.
Is there a way to add the Express to the network for this purpose?

"Is there a way to add the Express to the network for this purpose?"
Yes, configure the Express to "Join" the wireless network created by the D-Link and check the "enable ethernet clients" box. Post back if you need step by step on this configuration.
It's possible that this may work OK for you if you have a strong, fast wireless network. But, you may also want to consider that this would be quite a way down on the list of most desirable ways to connect the 360 to your network.
For the best video quality, suggested in order of preference:
Ethernet cable from one of the LAN ports on your router to the 360
Ethernet powerline adapter at the router end and another adapter at the 360 end
Wireless from your D-Link to the 360's wireless-if it will accept a wireless connection
Wireless from your D-Link to the Express. Ethernet from the Express to the 360
Would be interested in your feedback on your experience if you use the Express.

Airport Express won't extend wireless network

Similar Messages

Maybe you are looking for