Airport Express won't join via ethernet, only wirelessly

I have a Time Capsule, two AEs wired and another AE operating wirelessly in my home network. Problem is I can't get the wired ones to join as wired ones. They'll only connect to the network wirelessly. So I can have a network completely wireless but I'd prefer the speed of the two AEs wired. I've been through many attempts, set-ups and versions with the AEs trying to resolve this. A potential big wrinkle is that the router is connected to two different switches that handle the various ethernet cables serving many rooms in the house so I'm thinking that may be the problem. Is that likely or am I missing something?

Well, the way to do this would be to go ahead and setup both AirPort Express devices one at a time near the Time Capsule...and connect them directly to the Time Capsule using Ethernet.
Get them working correctly that way first.
Then, move them to the backside of the Ethernet backbone for the network. If the Express devices don't work there....then you have an Ethernet switch problem, an Ethernet cabling problem, or possibly both. Tedious troubleshooting will be required.
In situations like you describe, 90% of the time the issue boils down to an improperly installed Ethernet plug, a broken wire somewhere, or a bad port on a switch. That is not to say that this is the issue, but it is the area to place your bets.
We did not get any details about what generation model the Express devices might be, or what type of operating system you are using on the Mac or PC to configure the Express devices. We'll need basic information like that if you desire additional help.

Similar Messages

HT1515 do you need to connect the airport express to a router via ethernet or can it do it using wireless?

do you need to connect the airport express to a router via ethernet or can it do it using wireless?

There are 3 Apple routers....AirPort Express, AirPort Extreme and Time Capsule. Details here:
http://www.apple.com/compare-wifi-models/
Do you have one of these products in the living room?
If no, you can only use the AirPort Express by connecting to the router in the living room using an Ethernet cable at all times.

Connecting Airport Express (n) to WRT54G via ethernet

I am using Airport Express (n) currently and would like to connect to Blu-ray player with ethernet for netflix streaming. But as we all know, the AX has only one ethernet port. I have an old linksys' WRT54G. Is it possible to use this as a part of network without loosing the advantage of Wireless N network? My idea is to go from Cable modem to WRT54G, and WRT54G's LAN PORT out to AX. WRT54G and AX will be connected via ethernet so that it doesn't lose the advantage of the N network.
And Blu-Ray player will be connected to WRT54G via ethernet.
Can someone tell me if this works and if so, how do you configure each device so that you don't have ip address conflict or any other problem. Thank you.
Message was edited by: Kozo Okumura

Certainly that will work. Since they are connected via Ethernet, the wireless clients of the WRT54G will have no effect on the wireless clients of the AX.
The WRT54G will provide a 802.11b/g network while the AX can provide an 802.11n network.
The AX should be configured to create a wireless 802.11n network and it should be configured to act as a bridge (not sharing a single IP address).

Airport extreme won't connect via Ethernet to BT homeHub v2.0

Hi
here's what I want to do:
1. Homehub is connected to the phoneline and will provide a b/g network for my iphone/xbox/laptop1
2. I want to connect my airport extreme to this (from what I can tell this must be done through an ethernet cable) so that I can have a separate N network which only 1 laptop will connect to.
So the problem I have is that no matter what options I select in the airport extreme when it's connected via ethernet it tells me that nothing is connected to the Ethernet WAN port. I've tried two different cables different ports on the back of the hub etc. nothing works. Every time I search google or forums for an answer people just write "connected it via ethernet and it works great" but there's no guide to what settings to use that I can see.
Can someone please help me with some sort of noob guide to get this setup how I've stated?
Many thanks in advance

Hey Bob
thanks fro the quick response. I have actually tried exactly that but it still flashes orange at me I'm suspicious that the AE may have a fault because during the setup (i can't remember the exact steps) but I got the AE updated and it complained that it could read from the AE (error code was 10057). Googling this does thow up a couple of solutions which I haven't tried.
so my steps should be:
Factory Reset the AE
setup as join existing network
join via ethernet to create a 2nd network
connect up the cable to the WAN port and the Lan of the Hub
change to bridge mode.
One thing I did notice (which may or may not be related) is the subnet mask on the AE says 255.255.0.0 when I set it up like this. However when I make it just join the network without trying to create a new one (which works) it sets it to 255.255.255.0 . the IP address also begins 192.168.1.* whereas in the other setup mode it is something different. Does that matter at all?
Thanks
Alan

Airport Express Won't Join Network Anymore

I had my Airport Express set up in my house as a range extender for my Airport Extreme. It was working fine until I recently updated the Airport software (or firmware, I don't remember). Now the AP Express is blinking amber. I went through all the trouble shooting steps, including hard and factory reset. My Airport utulity (6.0) sees the AP Express, and it takes me through all the steps setting it up as a range extender for my basestation on my wireless network, but at the very last step it says there's an error connecting. When I connect via ethernet only it's yellow on the utility, with status saying there no valid IP address. Tried the same IP settings as my basestation, but no luck. It also says the wireless network can't be found.
Is this a software problem, or a hardware issue? I feel like I'm missing something simple. I would appreciate any help anyone can offer. Thanks!

Download and use Airport Utility 5.6
This was release the same day as 6.0 but 6.0 is quirky and exhibits strange behavior at times.
http://support.apple.com/kb/DL1482?viewlocale=en_US&locale=en_US
Do a Factory reset again and set it up using 5.6

Using airport express to extend network via ethernet socket

I have a wireless router set up which feeds my mac and tv (via a wired ethernet connection). I have also a pc which doesn't have wifi capability.
Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket? I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
Thanks

Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try.

Best Practices for Using Airport Express to Stream iTunes via Ethernet

So I've been reading various posts about using Airport Express to stream iTunes and I've been reading various posts about using the Ethernet port on the Express. However, not sure I've yet found an inclusive listing of settings for both. Wondering if anyone out there has such a thing?
I have an (older) Aiport Express (802.11g, no 'n') running the latest Firmware (6.3, I believe). I have it lashed into my switch via a Cat 6 cable and the 3.5 stereo mini running out to RCA jacks into my RussSound (home audio system) amp. I'd like to make the Express ONLY a iTunes streaming device getting its network link over Ethernet (AirTunes). So, what does everyone suggest for best settings for turning on the Ethernet, turning off the WiFi and running AirTunes?
Thanks much in advance!
cheers
cp root

Airport > Wireless > Wireless mode "off"
Internet > Internet connection > Connect using "Ethernet", Configure IPv4 "via DHCP"
Music > Enable Airtunes
Enable Airtunes over Ethernet (if this choice appears).
When I first did this, the remote speakers didn't appear in iTunes. I poked around to see what I missed and couldn't find anything wrong, but the next time I ran iTunes the remote speakers appeared.
If you run into a firewall problem, make sure your OS X firewall is configured to "set access for specific services and applications": http://docs.info.apple.com/article.html?path=Mac/10.5/en/18503.html
Firmware 6.3 is correct for your Express.

Airport Express Won't Join Actiontec Router LAN

The devices are a new Actiontec MI424WR router and a five year old Airport Express.
I've had no trouble getting other devices (802.11g and 802.11n) to join the router's LAN, and I have no trouble configuring the Express via Airport Utility. The Express worked perfectly with my old router, and the Express is able to create its own LAN (802.11g, WPA2), which my Mac can join. All software and firmware is up to date.
Any suggestions on getting the Express to connect with the router?

When you mentioned LAN and configuring the AirPort Express to create its own wireless network, I was thinking that you were talking about connecting the Express to one of the Ethernet or LAN ports on the Actiontec router.
It sounds like you really mean WLAN (Wireless local area network), correct?
See if the Actiontec router has a setting like WPA-PSK-TKIP and then try WPA/WPA2 Personal on the Express.

Airport Express won't join network and disappears from view once configured

Hi. I am having trouble getting my brand new Airport Express to connect to my network. I would appreciate any help you can provide. Here are the details:
Computer: iMac, G5 running OS X Tiger.
Network: Cable modem hooked to a netgear wireless b/g router. The router is configured to use WEP 128 bit encryption. I have connectivity on the router throughout the house on several computers and handheld devices (iPhone, etc).
Airport Express Version: 5.3.1
My goal is to add the AE to my current network in order to stream music from iTunes to my receiver.
When I initially opened up the airtunes utility to set up the AE the setup program was able to find the AE and walk through the configuration process. I followed the steps, entered the correct network name, encryption algorithm, password, etc. When I completed setup and hit the update AE button the AE disappeared from the setup application and the device began to flash yellow. While troubleshooting I have reset the AE dozens of times over the past couple of days. I have done both the reset with power on (press reset for 10 seconds waiting for the quickflash) and the hard reset (plugging the AE in with the reset button depressed until the quickflash starts). In either case, the AE is rarely detected by the setup utility (about 1 in 10 times). When it is detected, I walk through the set up and get the same results. I have attempted configuration using both the manual configuration option and the automatic "wizard-like" method.
I have tried to configure the AE wirelessly with it plugged in next to the computer and using a direct hookup via ethernet cable. Both methods produce the same results - flashing yellow light with AE undetectable by any Airport applications.
I have also tried to load an older version of the firmware (5.3) on the AE. When I hit the update AE button after configuring the update to go from the current version to version 5.3 I get an error message stating that "an error occured while attempting to update."
Thanks in advance for any help you can provide.

Hi guys,
I think I'm having the same problem as you all, and its driving me crazzzzy!. I added an AX to my existing network with a AEX all thru gigabyte switch, including the new AX. I set the brand new AX up with all the settings, hit update, all settings were configured and its working fine (i can see it in iTunes, stream music to it, all works fine) EXCEPT when i go to AU and try to go into the manual setting of the AX it just hangs, and after about 2 min, i get an error message:
"An error occurred while reading the configuration. Please make sure your Apple wireless device is plugged in and in range of your computer or connected via Ethernet and try again. (-6722)"
I have tried resetting it hard/soft/default but not sure if it really does reset it, still keeps same password, and network settings. Tried connecting it next to my existing AEX incase the AX is trying to communicate via WIFI instead of the hard wired ethernet. I'll try hard wiring it directly to my mac as some have had success.
I have tried using OX 10.5.3, but still misbehaves as b4 with OSX.4.11. So its not my mac setup.
I'll try to find the old firmwares as some have described, that might work....????
This seems a common problem to many, I hope that Steve & the Apple engineers have got these messages and are fixing the problem as we speak.
marc

Extend my wireless network w/airport express w/out connecting via ethernet?

Here's what I have:
I have an Airport Extreme Base Station Version 7.5.2 - named Jim's Base
I have an existing Airport Express that I use to stream music to my office stereo - named Jim's Office
I have a new Airport Express that I would like to use to extend my wireless network to my family room - named Jim's Extended. I have ethernet to my family room for my TV and Receiver and an ethernet switch with one available port.
Question, when extending my existing wireless network do I have to extend it using an ethernet cable or can it be extended "wirelessly" i.e. no connections except to 120v power?
Could someone share the exact instructions? I've been trying to configure this "extension" for several hours now but can't seem to get it to work - wired or wireless.
Thanks -
jP

Apple's instructions to "extend a wireless network" using wireless only are in the link below. Although the illustration pictures a 2nd AirPort Extreme, the setup for an AirPort Express is exactly the same.
http://support.apple.com/kb/HT4259
The Ethernet port is automatically enabled in this type of configuration to allow Ethernet devices to connect. If you need more than one Ethernet connection, you can add an Ethernet switch to the AirPort Express to create more connection capabilities.

Airport Express won't join my existing wireless network...

I have Broadband in my house. I have a wireless modem also. I have spent hours trying to have Airport Express join the network so I can use the music streaming feature, but I have so far not been successful. I have seen a lot of references to it being very easy and straightforward to set up with it doing most of the work itself. As in, plug in AE to a power socket, open Airport Utility and follow the instructions... It doesn't appear to be that simple, not by a long shot. Can anyone outline how this can be done in simple steps? All of the online steps I have tried do not work, with many of them referencing aspects of the Airport Utility GUI that don't seem to exist...
Any help would be greatly appreciated.
For the record, I DO NOT want to replace my existing wireless router, i just want AE to join the network...
Thanks...
Ronan

I have the same problem - the AE wont join my Draytek 2600 wireless network. I can stream music wired, but it refuses to join the wireless network. I have tried WEP, WPA, WPA 2 etc. Always get amber flashing light. Ive spent about 5 hours solid on it so far, and I'm a networking expert.
No other device on the planet has problems connecting to my wireless. currently I have:
1) Belkin wireless Skype phon (no problems)
2) SOHO wireless IP camera (no problems)
3) Intel Macbook pro (no problems)
4) G4 Macbook (no problems)
5) Dell D600 XP notebook (no problems)
Try to connect the AE? No chance. Its just broken.
I have tried every conceiveable manual setting on the device also.
If I manually set the ip (outside the DHCP range, but within the subnet), subnet, DNS sever, domain etc, I get a GREEN light, but nothing can communicate with it. The utility cant see it, and itunes cant see it.
The real problem is there is no way to know if the problem is with DHCP or the wireless. Does green light mean it has a wireless connection, or it has a valid IP?
Interestingly, if I start it with a wired connection, get a green light, then stream music to it, then pull out the wire, the green light stays, and music players for about another minute (presumably wirelessly, but who knows?) before the music stops and the device (replete with green light), becomes dead to the network.
APPLE desperately needs to sort this out. Its junk.

Connect to Airport Express to use AirTunes via ethernet cable?

Hi,
Here's my setup and question: I am connected to the internet using the wireless network in my house. I want to also connect my computer to my Airport Express for AirTunes which is hooked up to my stereo in the computer room. Since I'm already connected to a different wireless network for internet, can I connect my Airport Express directly to my computer using an ethernet cable in order to run AirTunes?
Thanks!

Hi.
You don't need to do that. You can simply set the express up as a "client" allowing you to be on the network and/or airtunes and/or wireless printing.
Have a look at this post for the relevant info:
http://discussions.apple.com/message.jspa?messageID=5578616#5578616
---

Airport express won't join network

I use an airport express to extend my network. It is the last model in the old style - if that makes sense - (It supports 5Ghz networks) - bought about a year ago. It's been working fine but suddenly stopped connecting to my network. I suspect a hardware problem - but how can I know for sure? It's in range of my Time Capsule - I've tried resetting it - occasionally it works but then drops the connection. Any thoughts would be welcomed.

Hi Nicholas Pritchard,
Welcome to the Support Communities!
The articles below may be able to help you with this.
Click on the links to see more details and screenshots.
Wi-Fi base stations: Setting up and configuring an extended wireless network (802.11n)
http://support.apple.com/kb/HT4259
Resetting an AirPort Base Station or AirPort Time Capsule FAQ
http://support.apple.com/kb/ht3728
Cheers,
- Judy

Airport Express won't connect to my local wireless

I have a Fios modem connected to a Belkin wireless router. My G5 is connected directly, and I use the wireless for iMac and laptop. Works fine.
I have an Airport Express. I can't get it to successfully connect to the network so I can broadcast iTunes to remote speakers. I can run Airport set up utility from the laptop and it goes through the whole thing- finally telling me "Congratulations, you're now ready to play music, etc. ". However, when I try to connect to the external speakers, which now show up in my iTunes, I get an error saying Can't Connect or "Cant read configuation", something like that. It's very frustrating. When I try to set up from the iMac, I don't get that far. I get to "wait while the AX restarts, but it never does and I finally get the "can't read configuation" message. Any suggestions?

It may be that the latest firmware update is version 6.3 for your hardware. You can find that at apple support here:
http://support.apple.com/downloads/AirPortExpress_Firmware_Update_6_3_for_Mac_OSX
That is a fairly old one, the newest updates in the 7.4 range update the extreme and express together. That one may just be for 802.11n hardware.
Sorry I could not be more help

Airport Express as an end point on a wireless network and connect a computer via the ethernet port?

Can I use my Airport Express as an end point on a wireless network and connect a computer via the ethernet port? - I'm wanting to connect a computer that does not have wireless and is in another building.

The requirements for this to work are:
1) The AirPort Express must be the 802.11"n" version. Model Number is A1264
2) There must be adequate wireless signal stength where the Express will be located
3) The Express must be configured to "join" the wireless network with the option checked to activate the Ethernet port

Airport Express won't join via ethernet, only wirelessly

Similar Messages

Maybe you are looking for