Airport Express wouldn't extend wireless network

Am posting this in case it helps someone else. I have an Airport Extreme set up as a base station and couldn't get an Airport Express to "extend wireless network". I finally found a checkbox in the "Wireless" tab of the "Manually Configure" dialog box for the Extreme that says: "Allow this network to be extended". I could not find this referenced anywhere in Apple documentation, so you have to know to go and check this box. Apologies to the techies if this is a no-brainer, but I only found it by accident. Apple should include a brief paragraph in their wireless troubleshooting guide on extending your network.

When you configure the Express to "join a wireless network" it becomes part of the network so that you can stream AirTunes to the device or use a remote printer connected to the USB port, but it does not provide any additional wireless coverage in this type of configuration.
"Extend a wireless network" does the same thing as above, except the Express will also provide more wireless coverage in the area where it is located.

Similar Messages

  • AirPort Express will not extend Wireless Network

    Hello.  My airport express will not extend my wireless network.  It was green for about the first 4 hours and then I've had a flashing yellow light since that time.  I've reset it a bunch of times and even have the AE in the same room as my AP Extreme.  I complete the setup and then it continues to flash yellow.  Can ayone give me a hand?

    In the cases where the AirPort base stations would be interconnected by Ethernet you want to configure then for a roaming network, NOT an extended network. Apple uses the term "extended" when the base stations use wireless connection. Regardless of naming convention the end results is pretty much the same.
    The link I provided should provide you with the necessary steps to set this type of network up.
    If you need additional help, please start a new post as the solution for you will be different than the OPs. Thx!

  • Airport express can't extend wireless network

    Airport express(A1264) can't extend wireless network. It seems that Airport express can't find my home Wi-Fi network. Amber light is blinking, and AirPort Utility of MacBook also can't find Airport express.
    If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
    It was successful only once, but all failed after that.
    Is there solution for this problem?
    [My system]
    Time capsule 4th generation
    Airport express 1st generation (A1264)
    [Settings]
    Time capsule (ethernet connected)
    - Create a wireless network
    - 802.11a/n - 802.11b/g/n (Automatic)
    - 2.4GHz / 5GHz Channel (Autmatic)
    - WPA2 Personal
    Airport express
    - Extend a wireless network
    - WPA2 Personal
    - 2.4GHz Wi-Fi network name and Password is set up

    If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
    Sorry, I misunderstood what you wanted to do.
    Since you did tell us that you had the Express connected with an Ethernet cable, I assumed that was how you wanted to configure the Express.
    But I want to extend a wireless network (not using ethernet)
    Because Airport Express and Time Capsule cannot be connect via ethernet cable.
    Follow the same setup as above....and do not connect an Ethernet cable.
    Keep the Express near the Time Capsule for the setup. Once you have a green light, move the Express to a point that is about half way between the Time Capsule and area that needs more wireless coverage.
    If you reset the Express several times and try the setup several times without success, I think you have to suspect a defective Express.

  • Airport express failing to extend wireless network

    Have got an airport extreme connected via ethernet to my Virgin Media hub (hub is in modem mode).  Also have an airport express to extend the wireless network.  Setup has been working perfectly for over a year, then this weekend, literally no settings have been changed, and airport express is giving me a status message of "This airport base station was unable to extend the wireless network. Make sure the wireless network you're trying to extend was setup and is working correctly, that you entered a matching wireless network password into this device and that this device is in range of the wireless network"
    I have reset to factory settings 3 times now and whilst it goes through the initial setup, i always get the same status message.  Front light is green. 
    The express version I'm using is the 2012 redesigned version, looks like a white Apple TV and it has the latest firmware.  I've tried configuring via my MBA, windows desktop pc (windows 7) and ipad, nothing works
    Any ideas?

    You have to think of the Express devices as matching pairs when you have one set up to create a wireless and the other to extend it. Here, I assume that you still have the extending Express set up to extend the network.
    Power off both AirPort Express devices. The power down order does not matter.
    Wait a minute
    Power up the main AirPort Express.....the one directly connected to the Virgin hub....and let it run a full minute
    Then, power up the extending Express
    Check the network and report on your results

  • Airport Express used to extend wireless network from Linksys?

    I've been asked if I can straighten out a wireless mess at a local church. They have a wireless network in their office (a seperate small building) using a linksys transmitter.
    The church (a seperate building 50 yards away is where they want to extend the network to.
    Currently, I can read the network there on whqat they have now but something is misconfigured and the manufacturer is being of little assistance.
    Has anyone used an Apple Airport Express to extend a 3rd party wireless router? Ive decided it may just be worth the cost to dump the relay they have and simply buy an airport express.
    Suggestions?

    The Linksys WRT54G and WRT54GS (not latest versions v5) are the only 2 known Linksys routers compatible with Apple's WDS.
    So if you are using one of those routers you should be able to do it.
    If you are using a different router it probably will not work.

  • Airport Express won't extend wireless network

    I think due to a fault my airport express wont extend my wireless network around my house , but it will allow for airplay ... is it possiple to extend my network using the express but with an eithernet cable rather than the wireless that is transmitted out of the express unit ??

    Is the other wireless router, that you are trying to extend, another AirPort or Time Capsule base station? If so, are both units 802.11n models? Finally, what is the rough distance between the units and are they located in the same room, different room, or different floor?

  • Airport Express wil not extend wireless network via ethernet

    I need maximum bandwidth in a area with poor signal. No matter what I do, the AE will not extend my APEBS dual band via ethernet. It will alway connect wirlessly giving me half the speed. I have 1 main network to extend. I have tried to extend the 5 GHz wide channel as a seperate network but this wont work either.(but thats what I want really. Please help. I have been at this a couple days already and I need to figure it out before my return policy wears out. Thanks!

    If you are connecting the Airport Express to your AirPort Extreme via ethernet, the AirPort Express should be configured as follows:
    Open AirPort Utility, click Manual Setup
    Click the Wireless tab just below the row of icons
    Wireless Mode should be set to "Create a Wireless Network"
    Wireless Network Name would be the exact name of the main network that the Extreme is creating, same security, password.
    Radio Mode must be set the same as the main network on the Extreme
    Channel should be set to be least 6 channels apart from the channel that the main network is using on the Extreme.
    Click the Internet icon above and look for Connection Sharing at the bottom of the page. This should be set to "Off (Bridge Mode)".
    Update to save settings.
    For more info reference page 42. http://manuals.info.apple.com/enUS/Apple_AirPort_NetworksEarly2009.pdf

  • I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

  • How to add airport express to my current wireless network

    Hi guys.
    I have a dlink router (ac) configured as NAT and a friend of mine gave me an airport express (ac) to extend my current wireless network.
    I believe that i should configure the airport express as bridge mode in order to mantain my current ip range.
    I'm trying to configure the airport express but i can't even loggin to it.
    The question.
    Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
    Thanks so much and any help would be really appreciated.
    Regards.
    Francisco.

    Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
    Unfortunately, the answer is that neither an AirPort Express nor an AirPort Extreme is compatible with a D-Link router....or any other 3rd party router for that matter.....if you are trying to have the the AirPort device extend the signal using wireless.
    The AirPort Express can extend a signal from another Apple router.
    'm trying to configure the airport express but i can't even loggin to it.
    You may have received an older version of the Express that is not compatible with the newer Mac operating system that you are using.
    Look for the model number of the Express on the side of the device.....hard to see in the faint print.....you may need a magnifying glass.  If you see model A1084 or A1088, these older versions are no longer supported by Lion, Mountain Lion or Mavericks operating systems.
    The workaround is that you must use a Mac that is running Leopard or Snow Leopard, or a PC to be able to administer the older versions of the AirPort Express models.

  • Adding Airport Express to D-Link wireless network

    We have a D-Link wireless router given us by our ISP. I have an Xbox 360. I'd like to take one of our Airport Expresses, and connect the 360 via Ethernet cable to the Airport Express, while the Airport Express joins the D-Link's network, thus giving my 360 wireless internet.
    We used to accomplish this using another Airport Express instead of the D-Link, but for our own reasons, we now need to use the D-Link.
    Is there a way to add the Express to the network for this purpose?

    "Is there a way to add the Express to the network for this purpose?"
    Yes, configure the Express to "Join" the wireless network created by the D-Link and check the "enable ethernet clients" box. Post back if you need step by step on this configuration.
    It's possible that this may work OK for you if you have a strong, fast wireless network. But, you may also want to consider that this would be quite a way down on the list of most desirable ways to connect the 360 to your network.
    For the best video quality, suggested in order of preference:
    Ethernet cable from one of the LAN ports on your router to the 360
    Ethernet powerline adapter at the router end and another adapter at the 360 end
    Wireless from your D-Link to the 360's wireless-if it will accept a wireless connection
    Wireless from your D-Link to the Express. Ethernet from the Express to the 360
    Would be interested in your feedback on your experience if you use the Express.

  • Airport Express joining Linksys WRT54G Wireless network

    I have spent hours trying all different ways of getting my Airport Express to join my Linksys network. And then I discovered that I have to *__remove the spaces from my WPA password__* in order for my AX to join the network. My iMac and MacBook all join the network with spaces in the password, but for some reason the AX does not.
    This may be superstition, but I also made sure the pass phrase was all uppercase and exactly 13 characters. Don't know if that makes a difference, but I was tired of trying different things.
    Hope this helps some one.

    I have spent hours trying all different ways of getting my Airport Express to join my Linksys network. And then I discovered that I have to *__remove the spaces from my WPA password__* in order for my AX to join the network. My iMac and MacBook all join the network with spaces in the password, but for some reason the AX does not.
    This may be superstition, but I also made sure the pass phrase was all uppercase and exactly 13 characters. Don't know if that makes a difference, but I was tired of trying different things.
    Hope this helps some one.

  • Airport express just stopped extending the network

    I have an airport express that I have been using for 3 years to extend the network in my house.
    All of a sudden it started flashing amber. I've tried soft resets, hard resets, factory resets, and I can't get it to extend the network anymore.
    I have 3 other expresses in the house that still extend the network, but this one won't.
    Everytime I go run airport utility, it sees the express, and will actually allow me to JOIN the network (I get a solid green light, everything is good) but everytime I ask it to EXTEND the network, it gives me an error message and says it can't do it.
    It's an old extreme, that I bought refurbished, so I might be able to accept it's old and needs to be replaced, but then why can I join the network, but not EXTEND the network?
    Any thoughts would be appreciated.

    Apple's instructions to "extend a wireless network" are on the main forum page and also here:
    http://support.apple.com/kb/HT4259
    Although the example pictures an AirPort Extreme as the "extending" device, the setup for an AirPort Express would be exactly the same.

  • How do i set up time capsule to work with airport extreme base to extend wireless network?

    i have a airport extreme base, how do i set up a time machine to extend the wireless network i have with airport extreme? i have also 3 airport express's connected to the same network to extend my wifi all over my house. thanks in advance.

    Much better graphics, thanks.
    You can leave the Time Capsule connected by Ethernet from the Linksys and configure for a "roaming" network as mentioned previously.
    To do this, open AirPort Utility - Manual Setup
    Click the Wireless tab below the icons
    Wireless Mode = Create a wireless network
    Wireless Network Name = Same name as the AirPort Extreme
    No check mark needed next to Allow this network to be extended
    Radio Mode = Same setting as the AirPort Extreme
    Channel = Automatic
    Wireless Security = Same setting as the AirPort Extreme
    Wireless Password = Same password as the AirPort Extreme
    Confirm Password
    Click the Internet icon, then the Internet Connection tab
    Connect Using = Ethernet
    Connection Sharing = Off (Bridge Mode)
    Update to save settings and allow the Time Capsue to restart
    Then power down the entire network
    Wait a minute or two
    Start the modem first and let it run a full minute
    Start the AirPort Extreme the same way
    Power up the switch
    Power up the Time Capsule for a minute
    Keep starting devices one at a time about a minute apart
    Now, your computer will automatically pick up a wireless signal from either the AirPort Extreme or Time Capsule, whichever device is closer and providing the stronger signal.

  • Why does Airport Express slow down my wireless network??

    Hello, guys! Here I am again, seeking for help...
    Ok, so here's the situation: my internet service provides me with 10Mbps. My cable modem is hooked up to a 4-month old Airport Extreme in my home office, two walls away from the living room, where I'm typing from now. Internet's wireless speed in this living room has always been about 10Mbps, barely any loss when switching my signal from cable to wireless.
    I then decided to buy an Airport Express in order to extend my wireless network, since I want to work in a room far from this living room and with Airport Extreme alone I got no internet signal there.
    Ok, so I installed the Express right at the living room (I can say it's pretty much at the middle of the house) and now I got full internet sign at the far room, great!
    HOWEVER, my wireles speed has been cut by half!! At this very same living room where the signal was 10Mbps before I installed the Aiport Express, it's now - at the very best!- 5Mbps!! Needless to say that it's even slower at the far room it was intendend to extend the signal to, but that was kind of expected.
    *But why does it cut in half my internet speed at the living room if Airpot Extreme IS delivering 10Mbps at that point of the house??* Am I not setting it up properly, how can I solve this??
    Thank you so much for any help you can give me!
    Cheers,
    Renata
    Message was edited by: rgobrasil

    After some more analysis, I discovered that this tends to happen everytime a Time Capsule backup is performed.....

  • Airport Express Conflicts with Clear Wireless Network?

    After months of stumbling around, trying to figure out why my Clear Wireless internet service was so choppy, I finally plugged the ethernet cable directly into my computer, and disabled my local Airport network. Voila! Works like a charm -- very fast and reliable, now. Trouble is, I don't have network access for my laptop. The problem (I suspect) is that I also have phone service on my Clear modem.
    Here's what the connection looked like (and was recommended by Clear Wireless), with <-> meaning wireless connection and <+> meaning an ethernet connection:
    computer(s) <-> Airport Express <+> Linksys Phone Box <+> Clear Modem <-> Clear Tower
    So, pulling the Airport Express out of this sequence cleared up ALL of the stalling problems and slowness. My new (and functioning) set up looks like this:
    computer <+> Linksys Phone Box <+> Clear Modem <-> Clear Tower
    My question is whether I can have somehow connect the Airport Express on the other side of my computer, and allow my local network access the Clear Wireless modem via my computer? Right now, I've got the Airport Express plugged in and running, mostly to check if there was simply an interference problem, and that doesn't seem to be the case (the phone connection is a base station with wireless handsets, so thought there might be interference there -- doesn't seem to have been an issue).
    Any advice on this would be great. Clear Wireless is as clueless on technical support as it is brilliant in concept. Still very much in startup mode, with phone operators reading from generic scripts and masses of angry users spamming their discussion board -- ugh! Thus my post here. I'd love to see a schematic that shows the optimal way to bring a phone connection into a local wifi network.
    Thanks!

    What I would like to do is to connect the airport express to the wireless network (Linksys-router).
    What are you trying to do with the AirPort Express Base Station (AX)? Use it for streaming iTunes and/or share a USB printer, or extend your existing Linksys wireless network?

Maybe you are looking for