Airport Extreme (3rd Gen) super slow on selective devices?

Hi, I have a problem here that's got me scratching my head. I have had a 3rd Gen Airport Extreme 802.11n (MB763LL/A) for over 2 years now. For the most part it's worked great, allowing me to get the full speed I pay for through my ISP on all my devices: PC, Macbook Pro, iPod, iPad, Android Phone etc. However, recently I've noticed that the only device that I can get the full speed on is my macbook pro (4-5 Mbps down). All other devices now crawl at a speed of <1 Mbps down. I restored the Airport to factory settings and set it up again as new, but the same problem remains - full speed on macbook pro, painfully slow on all other devices including iPad and iPod.
I tried connecting the cable modem to a linksys router that I had lying around and as soon as I set up the network, all devices were connected and downloading at the full 4-5 Mbps speeds. So it definitely seems to be an issue related to the Airport rather than the wireless radios in individual devices. The funny thing is that I've made no changes to the airport - no firmware updates, no new devices etc.
What do you think? Thanks in advance!

Yes, I have had similar problems...
I have a 2nd gen AEBS TimeCapsule as the main router, and a 1st gen AEBS acting as a bridge to extend the network. Both have up-to-date software, as do all of my Macs.
After moving my MBP from one end of the house to the other and back (so, bouncing between the wifi units), I got into a situation where it looked like nobody else was online in bonjour chat, even though they were, and some of them could see each other. Some could even see me. But my chat showed nobody else online.
At the same time, I found that I could no longer print to my (bonjour) print queue. Others could also not print.
Rebooting my laptop did nothing, nor did switching ipv6 off and on (per some recommendations I saw), nor anything else.
The ONLY thing that finally got it all working was when I decided to bounce the AEBSes (I used hard power-offs), and then instantly my chat started showing other bonjour users, and I could print.

Similar Messages

Airport Express (2nd gen), Airport Extreme and Airport TimeCapule (3rd Gen) interoperability

Airport Express (2nd gen), Airport Extreme and Airport TimeCapule (3rd Gen) interoperability
When all configured to provide wireless the network (Wired/Wireless) become unstable and very slow. When I disable wireless on the Airport Express the problem disappears. The problem effects all endpoint clients (iPhones, iPads, Mac's and windows) Any ideas?
I own the following
Airport Express 802.11n (2nd gen)
Airport Extreme 82.11ac
Airport TimeCapule 802.11n (3rd Gen)
Config
Each of the Airport's WAN port is connected my AT&T Uverse modem
Latest firmware on each device
All use static IP's (192.168.1.x)
Airport's are all configured to "Create a wireless network" with same network name, security and password.
Wireless options are using Automatic for Radio's and Channels
Router mode is "Off (Bridge Mode)"

ragu75 wrote:
Config
Each of the Airport's WAN port is connected my AT&T Uverse modem
Don't do that. Decide which one of your AirPort Base Stations is to serve as your router. Connect that one, and no others, to the modem. Connect all the others to it, and configure them as bridges.

Extending an Airport Extreme (6th Gen) network with older Airport Express models

I just purchased the latest Airport Extreme (6th Gen) base station to be my main wifi router. I have two airport express models that I used in the past to extend my network with my (very) old retired Airport Extreme (2nd Gen): the 2nd Gen model A1264 (you plug into the wall directly) - I've had it for several years, and the newest 3rd Gen model A1362 (small square that lies on a desk or table) - I just purchaed a couple of months ago.
My question is - will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)?
I don't have any AC capable clients yet - so everything is running on the "n" band - and the older Express is an "n" model, but I just have this (perhaps irrational) fear that attaching older routers will slow everything down.
Any thoughts or suggestions?
Thanks!

will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)?
The A1264 model will be able to extend only one band of the new dual band AirPort Extreme. Normally, the A1264 will extend the 2.4 GHz band since it is stronger than the 5 GHz signal.
The A1392 will be able to extend both bands since it is also a dual band model, providing that it is located where it can receive a strong wireless signal from the new AirPort Extreme.
Here, I am assuming that you are asking about extending wirelessly.
You might want to keep in mind that extending wirelessly always involves compromises and loss of bandwidth. The main reason for this is that an extending device can only "extend" the quality of signal that it receives.
The wireless signal from the new AirPort Exterme will slow down and lose strength the further that it moves away from the main AirPort. So, the extending device gets a slower, weaker signal to extend. The result is signficantly slower wireless performance in the extended areas.
The way to solve this is connect the extending AirPorts to the main AirPort using a permanent wired Ethernet connection. There is no signal loss in a wire, so the extending AirPort receives a full bandwidth signal to broadcast. The result is higher and more uniform speed on the entire network.

Airport Extreme 2nd Gen - can not retrieve or assign an IP address

I had two 2nd gen Airport Extreme base stations. One connects to the internet, the other bridges the network to my office where I have wired devices connected. The office base station was no longer allowing me to connect to my USB drive for time machine backups, but all of the wired devices were routing to the internet properly.
I purchased a new base station (5th gen), bringing my total to three extreme stations and two express base stations (one express for an old wired network printer, the other for streaming music).
The old main base station is moved into the office, and the new base station (5th gen) becomes the "main" internet access point. I reset both devices and they install without a hiccup. Ditto the new express stations - they connect without having to reset them. Everything works as it did before the upgrade.
I take the old office base station (the one that would not allow me to backup via time machine) and do a factory reset. It reboots, the light flashes yellow (not surprising). I hook an old macbook (10.6.8) up to the old base station (and turned off the wifi) using a wired ethernet cable the ethernet port is assigned an IP address (10.0.1.2) via DHCP. My other macbook pro (10.8.5) running the latest AirPort Utility sees the old base station using wifi (under other wifi network). I select the old base station it automatically connects it to my new base station stating:
"This Airport Extreme will now be set up to extend <my new 5th gen AirPort Extreme base station>"
I change the default name and click next.
Now when the old office base station boots it will not connect to the network - it still flashes yellow. It will not assign itself an IP address, the macbook plugged into the ethernet port (using dhcp) shows (under network settings):
"Ethernet has a self-assigned IP address and will not be able to connect to the internet."
(the 169.... number)
Now the funky part. I manually set the wired ethernet's IP4 configuration (IP, subnet, router and dns server) on the old Macbook running snow leapord (10.6.8) - remember the wifi is turned off - and bingo - I am connected to the internet. All the while my old AirPort Exreme continues to blink yellow. If I manually assign an IP address to the AirPort Exreme's light turns green.
Clearly the old device is working. The ethernet port works, the wifi works - routing traffic from the wired ethernet through my home network and out to the internet. My AirPort utility on all my macs can see the base station, and can configure it (via wifi). I have even tried (via wifi) downgrading the firmware to 7.6.3 and then to 7.6.0 and the back up to 7.6.4. The only thing it will not do is give retrieve an IP address, or assign an IP address to wired devices.
Any ideas?

I attempted to see/access (via the Disk Utility on my iMac) two drives already connected to my AirPort Extreme, but could not.
These drives are shared "network" drives, which Disk Utility cannot access. Disk Utility will only be able to access a drive if it is connected directly to a Mac.
If you need to format the drive(s), partition them, etc., you must do so with the drive connected directly to the Mac, then move them to the USB powered hub location at the AirPort Extreme.
These drives are available through the Finder and are used for Time Machine
Apple does not officially support Time Machine backups to a drive connected to the AirPort Extreme, but some users seem to be able to make this work.
1) Can I see/access USB drives (properly fomatted and visible/accessible in the Finder window) attached to my AirPort Extreme (2nd gen-firmware version 7.6.2)via a powered USB hub?
Probably. Some users find that one powered hub will work for them while another might not. To "see" the drives, you must first click on the AirPort Extreme icon under the SHARED heading in the Finder. Then, if the drives are formatted in Mac OS Extended (Journaled), each drive will appear as a folder. Double click the folder name to mount the drive on the desktop.
2) Can I use my iMac (running Lion 10.7.4) to create a concatenated disk set with USB drives (of varying size) attached to my AirPort Extreme via a powered USB hub?
The drives will all appear as separate drives, which must be accessed separately. If you were thinking of trying to start Time Machine backups on one drive and have them continue automatically on another drive when the first drive is full, that will not work.

How to connect an HP 111 designjet with my airport extreme 2nd gen with bonjour for windows

Hi:
I have an HP 111 Tray, plug into an airport extreme 2nd Gen, both works properly running in a PC with windows 7.
When I start Bonjour for windows it identify de printer, but when i continue my printer is not in the list, I used the browse buttom and selected the .inf file that is contained in the driver and Bonjour collapsed everytime
Any one can Help me??
Thank you guys
Hola:
Ante todo buenos dias, os cuento mi problema:
Tengo una impresora gran formato HP 111 Tray (con bandeja) enchufada a un router Airport Extreme de Apple de 2ª generacion, ambos funcionando correctamente y con las ultimas actualizaciones de firmware, el caso es que al abrir el asistente BOnjour para imprimir en red a la hora de seleccionar la impresora no aparece entre las opciones disponibles, a pesar de reconocerla. Al darle a examinar para que utilize los datos de Información sobre la instalación (.inf) que me he bajado de la pagina, Bonjour se queda colgado siempre
He probado desde dos ordenadores diferentes conectados a la red y nada
Alguien sabe como puedo solucionarlo.
La impresora se conecta con un USB al router de Apple
Muchas gracias de antemano

What model and firmware is the 2TB TC?
What firmware is the AE?
Does the AE get good signal from the TC in its current location?
Signal can only be extended that is received intact.
Is it extending on 5ghz? As I remember it a Gen2 AE is only single band, although you can choose either 2.4ghz or 5ghz.
I am fairly sure you are going to tell me your TC is AC model..
I would do a couple of things..
1. Fix the wireless name, make it short, no spaces and pure alphanumeric.
2. Fix the wireless channel for 2.4ghz so it is not going to jump around.
3. Get real results from the AE in its current location for signal strength.. this is really only possible on v5 utility. And that is a double pain with Mavericks because you cannot use it.
Apple have removed all the useful diagnostics from the airport utility. There is next to nothing left. So you need to use the computer and its diagnostics to find signal levels in the location.
http://support.apple.com/kb/HT5606

Best setup for new airport with wired connection to old airport extreme (4th gen)

I have an AirPort Extreme (4th gen) in my basement (of a three story house) connected directly to the Fios box (I am not using the Verizon g router). The new AirPort (ac) is connected to the old one by in-wall Cat 6e to an upstairs bedroom. Can/should I turn off wifi on the n router for best wireless performance? What would the optimal setup be?
On the airport utility I selected "replace existing Airport" and the new ac router is up and running and working fine. I wonder whether the fact that wifi on the old Airport is still on may be good for coverage around the house, but compromising the wireless bandwidth/speed? I haven't noticed any speed issues yet, but I do a lot of video streaming so I want to ensure I have the best setup. Range doesn't seem to be a major issue in my house. It is more important to me to have strong wifi signal upstairs.
Thanks in advance for advice.

If the AirPorts are connected using Ethernet, then no bandwidth is being lost on the network. Keep the wireless functions "on" at both AirPorts for additional wireless coverage and speed.

Airport Extreme 5th gen overheating

Lately we've had some very hot weather, and my AirPort Extreme (5th gen) has been dropping out in a weird way.
It drops all connections, the other connected AirPorts flash orange, but the Extreme just sits there with a green light like nothing is wrong.
Only unplugging and plugging in again fixes it. When this happens, it feels quite warm on the top, which makes me think it might be overheating.
Setup is basically AirPort Extreme handling PPPoE login bridged to a DSL modem, two AirPort Expresses wirelessly extending and bridging the network to Ethernet, no direct Ethernet connections on the Extreme. Latest firmware.
Worth taking it to the Apple store? Bought it in August 2012.

Well it is out of warranty unless you have applecare on a computer or ATV, that is current.
I would say the latest firmware is fairly bad for this setup.
Return it and the express units (I know less about them) to 7.6.1 firmware and do a factory reset and start over.
Ignore any future request for upgrade of firmware.
What airport utility are you running?
Downgrade is very easy from v6.. hold in option key and click the existing version number.. and a selection of firmware will be presented dependent on the model.
In very hot weather.. Like 4 days of over 40deg we just had in Melbourne.. you would find the top of the TC 15deg above ambient.. it is pretty hot.. more than 20 is serious.

AirPort Extreme 6th gen, not recognize my printer HP deskjet ink advantage 1515

I have AirPort Extreme 6th gen, it can not recognize my printer HP deskjet ink advantage 1515.
I already contact hp support and they reply my printer is support by AirPort Extreme. This is the link web statement http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00710847&tmp_task=useCatego ry&cc=us&dlc=en&lc=en&product=5385208#N59
Also doing all instruction on the web, update firmware for AirPort Extreme and my ipad to latest firmware.
But until now I can not share my printer through my AirPort Extreme 6th gen in my network.
Anyone know how to solve this problem?

Hi tonyioancy,
Welcome to the HP Support Forums! I see you are running into a few problems with your HP Deskjet Ink Advantage 1515.
I would like you to run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
If you run the PSDR and are still experiencing the issues, please contact our technical support at 800-474-6836 as your printer may still be in warranty. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www.hp.com/cgi-bin/hpsupport/index.pl
Thanks,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Usb hard drive connected to AirPort Extreme 5th gen not detectable

hello
I connected a exFAT formatted HD via USB to my AirPort Extreme 5th gen.
I'd like to have access to it via my iMac as well as my gf's win laptop.
I only can se the drive in Airport utility but am not able to use it (copy files, read files I put on directly connected to my iMac).
so what could I do?
thank you in advance!
cheers Chris

Thank you!
That was a great hint. I can now access the external HD via my iMac.
on the other hand I'm no longer able to go online with my gf's win laptop.
there's no way to get an internet connection working.
I can see the wlan of the airport extreme but I am not able to log in...
I have no glue!
any help is highly appreciated.

Can't print from iPad to HP via Airport Extreme (5th gen)

I have an HP Deskjet 5900 connected to an Airport Extreme (5th gen), via the USB port. I'm currently running 10.6.8 and have succesfully setup the printer such that I can print wirelessly from my MacBooks, as well as directly from my MacPro desktop (which is connected to the AEB through the network).
What I can't do is AirPrint from my iPad or iPhone.
I've skimmed through quite a few questions on here, but haven't come across this specific scenerio. The closest one refers to printers that are AirPrint compatible, but I believe that only applies to wireless printers that are being connected on their own (without an AEB).
I really hope I don't have to download an app for this... it's built right into the iOS!
Thanks for the help.
Stephen

To use AirPrint directly from your iPad, you will need a printer that is AirPrint-compatible. Currently, the HP Deskjet 9500 is not one of them. There a few workarounds, but they will require obtaining an App.

HT3546 I have been unsuccessfully trying to extend the wifi of my Time 2T Capsule with an Airport Extreme 2nd Gen. It works for a while and then loses configuration. I have done everything possible, disconnected it, reset it but it keeps failing, what to

I have been unsuccessfully trying to extend the wifi of my Time 2T Capsule with an Airport Extreme 2nd Gen. It works for a while and then loses configuration. I have done everything possible, disconnected it, reset it but it keeps failing, what to do?

What model and firmware is the 2TB TC?
What firmware is the AE?
Does the AE get good signal from the TC in its current location?
Signal can only be extended that is received intact.
Is it extending on 5ghz? As I remember it a Gen2 AE is only single band, although you can choose either 2.4ghz or 5ghz.
I am fairly sure you are going to tell me your TC is AC model..
I would do a couple of things..
1. Fix the wireless name, make it short, no spaces and pure alphanumeric.
2. Fix the wireless channel for 2.4ghz so it is not going to jump around.
3. Get real results from the AE in its current location for signal strength.. this is really only possible on v5 utility. And that is a double pain with Mavericks because you cannot use it.
Apple have removed all the useful diagnostics from the airport utility. There is next to nothing left. So you need to use the computer and its diagnostics to find signal levels in the location.
http://support.apple.com/kb/HT5606

Why can't I connect to my airport extreme(4th gen.) after reseting the password

i was changing the password on my airport extreme(4th gen.) and it said that i changed it succesfully but it had a error when it was restarting and i can't connect back to the internet what should it do

Please perform a Factory Default Reset to clear the old, and possibly corrupted settings on the AirPort Extreme to get it back to original settings. Then, reconfigure the device again using the passwords of your choice.
Resetting an AirPort Base Station or Time Capsule FAQ

I will have an AirPort Extreme 5th gen in a few days.....

I will have an AirPort Extreme 5th gen in a few days. I have an older model and when playing with settings, I found out that my Epson wireless printer can only see 2.4 ghz 802.11n networks.....
but I want to use the 5Ghz wireless.....is there anyway to bridge the 2 networks or connect to both for AirPrint's sake?
Any suggestions?

but I want to use the 5Ghz wireless.....is there anyway to bridge the 2 networks or connect to both for AirPrint's sake?
If the printer can only support the 2.4 GHz radio band then, even if you could bridge the two (not possible), the printer would still not be able to connect ... and this is true for any wireless client whether it is a printer, computer, etc.
Wireless clients that support both bands can connect to one or the other typically based on received signal strength. They don't connect to both simultaneously.

Multiple WPA2 passwords on Airport Extreme (5th Gen)?

I have just purchased an Airport Extreme (5th Gen) and would like to set up each radio with a different WPA2 password. Is this possible?

Unfortunately, Apple does not provide this option.

Airport Extreme (2nd gen) not seen in Finder under "shared"

Specs:
15-inch Early 2008 >Processor 2.4 GHz Intel Core 2 Duo>Memory 4 GB 667 MHz DDR2 SDRAM>Software Mac OS X Lion 10.7.5 (11G63)
Airport Extreme Second Gen with Airport Utility 7.6.1
I do not want to update to Mountain Lion again.. since the first time proved to bring with it crashing and lots of glitches. And, I only ever do totally clean installs, wiping my HD with a 3x pass in disk utility. Main problem: External HD's which used to connect to my network with the AE under the "shared" sidebar, no longer appear. Matter of fact, my Airport Extreme in general, no longer appears in the Network folder. Nor do I see the ext HD under the "Disks" tab in Airport Utilities.
The external IS formatted as HFS Journaled *extended*, and has been for a while, back to when it used to work. I'm not sure of when it stopped being recognized, but the factors that have changed since then are that I did update to ML, but soon after went back to Lion. I also recently moved, and had to set up a new network of course. I also think perhaps that the Airport Utility version changed during this time.
I've read so many support documents, forum threads *different forums* and nothing seems to point me to a working solution. The HD does indeed work, since I of course plugged it straight in to my MacBook Pro's, and it shows up on both of them. Oh, should note that the other MBP is a year newer than the one listed above. It is the first unibody model 13". Question is, why would something that was working, stop working? I'd maybe be brave enough to roll back to Snow Leopard, but I'm really positive it was also working under Lion, so I shouldn't have to.
I'd really love some help on this please. Oh, and this is NOT in order to use Time Machine. I never use it. This is simply to access redundant backup drives on the network for photos and music.
Thanks much,
Doug

I spoke too soon, sort of. While the information I got from the Sonos website is accurate, and did indeed help in getting things started, the external HD with the enclosure I bought still isn't working! I even went so far as to reformat the drive last night, even though it was already formatted correctly. Just tried a few minutes ago, and nothing... The permissions look exactly as they do on the other disks so I'm not sure of what's up. At first, I thought that maybe Apple changed something about how the Airport Extreme sees externals, such as they must meet specific network based criteria... but then I tried a several year old iOmega portable Go drive, that I hooked up via micro USB and it worked immediately.
Now I'm wondering if there really might be something to what you said, about the enclosure. Is there a precedent for such an issue? Has anybody else here experienced this? But the wacky thing is that this external with enclosure was working perfectly not too long ago. So what has changed? I moved, and set up a new network. That has changed. But aside from that? I tried earlier firmware versions, and that did nothing. So either an OS update or my enclosure is all of a sudden wonky... even though it works perfectly otherwise? VERY confusing. BTW, the enclosure is a Rosewill.
Doug

Airport Extreme (3rd Gen) super slow on selective devices?

Similar Messages

Maybe you are looking for