Airport extreme 5.8 ghz with a netgear router at 2.4 ghz?
We will be getting a new imac which I would like to run wirelessly as part of a home system with two other ethernet connected macs and a wireless PC laptop. We expect to get substantial interference and would like to get the airport extreme and run it at 5.8 ghz to avoid home problems. Our current netgear, which works fine with the laptop, runs on the 2.4 spectrum. Is it possible to connect the netgear to the airport extreme and continue to use the wireless part of the netgear router/switch for the pc laptop (and avoid purchase of a new wireless card).. and have the imac at the 802.11n speed and the higher bandwidth because of the extreme router? Hope I explained this correctly. thanks.
bkenney1, Welcome to the discussion area!
Yes it is possible to operate the Netgear at 2.4 GHz while operating the AirPort Extreme base station (AEBS) at 5 GHz.
This is a 'dual band' network. It is discussed in the Apple documentation and in several threads in this area.
Similar Messages
-
AirPort Extreme Would like to eliminate comcast netgear router. Flashing amber light.
Hi. I have Comcast service for TV and Internet. The provided Comcast modem is an Aries and the router is a Netgear. Both are located on my garage at a panel box where all cables come in and get distributed around the house with an 8 port switch (large house- all wired with rg6 and coaxial). The layout is comcast main cable-aries modem-netgear router- netgear switch- wall jacks through out house. As expected the wired signal from the provided netgear router only worked near the garage. So I purchase an AirPort Extreme and hooked it up to the wired signal at the middle of house Internet jack. Questions:
1). My AirPort Extreme has a flashing amber light. Can't get a green signal. But it works
2). Can I get rid of the Comcast netgear modem? Compatibility with AirPort Extreme ?? I would save money from rental!!!
3). If so would the signal from the new AirPort Extreme cover the house from the garage?
4). Is there a better way of configuring the network? Or another piece of equipment that I need to buy?
ThanksConfirm the Ethernet jack you are using is operative by connecting a computer to it and temporarily disabling the computer's wireless.
If you use AirPort Utility on a computer or iOS device, it will tell you the reason the Extreme's LED is flashing. I suspect it has not been configured as a bridge - change its "Connection Sharing" to "Off (Bridge Mode)". Make its wireless network name and security settings identical to your existing wireless network.
You will still require Comcast's Arris modem.
The signal from the new Extreme, plus that of your existing Netgear router, should be sufficient to provide wireless service for most modest sized houses. It's impossible to be certain due to the nature of wireless communication.
A garage is not the ideal location for either a wireless access point or a switch. Since both of them need to connect more or less radially to the devices that require it, a better location is in the center of a house. Panel boxes are almost always in a corner. That's convenient for public utilities, not so much for wireless. It's also the easy way if you're a Comcast technician. If your house is already wired for Cat 6 as well as cable, it would not involve much additional effort to relocate your Comcast modem and existing router so that your wireless network will serve your house more effictively. Two wireless access points as you propose will also mitigate this. -
Time Capsule/Airport Extreme is the same as a Netgear router, right?
Idiotic question, I know. I just wanted to be sure before I bought it. I have Comcast cable internet and I'm leasing one of their Netgear Wireless Cable Modem Gateway - CG814WG routers. That router is horrible (the connection dies when my wife is on her computer and I'm playing Halo 3) and I want to replace it with Time Capsule so I can have a better connection with my computers and XBox 360. The Time Capsule/Airport Extreme can replace my Netgear with no problems, right? I believe I'll have a much better network experience without losing connection like I did with my Netgear.
Side note: The internet feed to the house is fine. My cable tv is fine and the line is good, so I'm figuring it has to be the horrible router since everyone else has complained about that model from Netgear as well. I'm just hoping Time Capsule will be my ultimate replacement.Excellent. I did contact my ISP and cross-referenced their list with the bestselling cable modems on Amazon.com. Looks like the Motorola SB5120 Surfboard modem works great. It also has an ethernet port and cable so I guess that'll connect easily to Time Capsule since you said I only need an ethernet cable.
I guess I might have to make sure the initial setup goes good, in which case I might be back here to make sure I did that right.
Thanks for the help though. At least I'll know that I'll have the right hardware that works with everything I have.
Message was edited by: SomeTechGuy -
I have a new Airport Extreme that works great with my IMac but keeps dropping out on our Windows 7 PC. I have tried all 11 2.4 Ghz channels and they all have dropout issues. Any suggestions?
Hello sstefanik
Check out the articles below to troubleshoot your issues with getting a proper connection with Wi-FI. Try creating a new Network Location and join your network to see if you can get on that way.
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Using network locations (Mac OS X v10.6 and later)
http://support.apple.com/kb/ht5289
Regards,
-Norm G. -
How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.
The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network. -
Hi. I am having issues with copying files to my shared WB 2TB HDD connected to my airport extreme. Comes up with error 50. I am using a Macbook Pro to copy from so not sure what I am doing wrong. Can someone help? thanks Rory
These links might provide some information that may be of help.
http://support.apple.com/kb/TA20831
https://discussions.apple.com/message/2035035?messageID=2035035
I've encountered this error myself upon occasion. If I remember correctly, it was a permissions/ownership issue with the some of the files I was copying. -
Will my airport extreme 2nd generation work with docsis 3.0 cable modems?
Will my airport extreme 2nd Gen work with docsis 3.0 cable modems?
RRoger, everything is working fine.
So, what is the actual problem here? You are now wondering if the Vonage can handle the speed from the modem? Is that the "problem" after all this discussion?
now I am wondering if my current setup will allow me to get docsis 3.0 speeds.
What speed is your Internet provider delivering to you?
The AirPort Express uses 100 Mbps Ethernet ports, so it will handle up to 100 Mbps. We have already told you that.
Vonage likely does the same. The answer is almost certainly "yes" .......both the Vonage and AirPort will handle the speed from the modem.
If you want to double check this, please provide the model number of the Vonage, and we will try to look up the specifications for the device. If you have documentation there with specifications for the Vonage device, check to see if the Ethernet ports are listed as 10/100. This is standard with almost all devices, with some of them handling even higher speeds 10/100/1000.
Chances are, your network will handle a lot more speed than your service provider is supplying to you. So, the "choke" point on your network may very well be your service provider and modem......not the Vonage and AirPort. -
Just bought a brand new airport extreme and having trouble with it being recognized. My mac is version 10.5.8. What should I do?
The new AirPort Extreme needs the 6.x version of AirPort Utility, which comes packed in with Lion 10.7.5 or Mountain Lion 10.8.x......or......you can also configure the device using an iPhone or iPad running a recent iOS.
From Apple's Specifications:
Setup and Administration
iPhone, iPad, or iPod touch with iOS 5 or later and AirPort Utility 1.3
Mac with OS X Lion v10.7.5 or later and AirPort Utility 6.3
A few options.....
Borrow another Mac running Lion or Mountain Lion for 10-15 minutes and set it up. The Mac running 10.5.8 will be able to connect to the wireless....but it will not be able to make any changes to the configuration of the Extreme.
Update to Lion or Mountain Lion.....but check first to make sure that your Mac will support the operating system first.
Use....or borrow an iPhone or iPad to set up the Extreme -
Can i use my airport extreme as a modem with comcast
can i use my airport extreme as a modem with comcast cable
No, since there is no modem on board an AirPort Extreme, so you will need to use an outboard modem if you want the AirPort Extreme to have Internet access.
-
Our airport extreme network works fine with our 6 devices. But when someone comes over and tries to log on, they can't until we restart the airport. Then they can get on, but it knocks one of our devices off the network. Any ideas?
I have not done a factory reset, I was trying to find out if I had some setting configured wrong first. I figured I'd just make things worse if went through a reset!
Here is a couple of screen shots: -
Airport extreme won't work with Optimum cable
Bresnan Cable just switched to Optimum. My internet no longer works using Airport Extreme. Cable is working as is wireless. Optimum support says it has something to do with external versus internal IP addresses and weather my Airport Extreme was configured as a switch or router?
I have a toshiba laptop and it works prefectly with a conceptronic usb card. But you must set up the Base Station only with the default options. I mean that you can not hide the SSID, or make an access control with Airport Extreme. You only set up the default options and it works perfectly. When I try to place an access control or hide the network then it doesn´t work and wait an ip as you say in your post.
If you want to connect from Windows to the Base Station you need to close your firewall and no other cable into the Airport Extreme, only the cable that you are connecting to access the Base Station. And it will work. -
My airport extreme only will connect with computer or ipad not both
my airport extreme only will connect with computer or ipad not both
We need just a bit more information, please before we can begin to accurately troubleshoot this issue.
1) What is the make and model number of your modem?
2) What operating system are you using on the MacBook Pro at this time. Your tagline indicates that you are using OS X (10.4.8), but this is about 6-7 years out of date.
If you are no sure which operating system your Mac is using......click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X Version number that you see there. -
I have a new Airport Extreme that works well with my IMac but is intermittent with our Windows 7 PC. Any ideas?
Thanks planb77. Your instructions worked but I had to do a little more than you stated. I did not realize that transferring files to a new computer was not enough. When the iPod synced I was told I needed to "authorize" my new computer to get my iTunes purchases to sync to the iPod. So after the initial sync, I ejected and disconnected the iPod, went into the iTunes store, set up "home sharing" and then authorized the new computer. When that was done I reconnected the iPod and was able to sync all my books and music. The only thing I couldn't do was rename the iPod as iTunes never asked me to. Is there a way to rename it after it has been set by iTunes as "owner's iPod"?
-
I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?
Before I bought it I did the same question at the Apple Store, and they told me "You can extend your existing Wi-Fi Signal with Airport Express wireless...
You cannot extend wireless from any brand except another apple router.. the store might have assumed you were using an apple main router. Most people who buy express buy them to extend an extreme or time capsule.
You are correct .. in the setup documents it does say 5.6.1 is adequate to do the setup.. my bad.. !! -
Does Airport Extreme (latest version) work with Netgear DM111P
Does anyone know - will the latest Airport Extreme work with a Netgear DM111P?
If so, great. If not, what is the recommend modem to go for?
Many thanks in advance.
MattSo, all I need to do is to disable wireless on my BT Home Hub?
Not necessarily. You could run two separate wireless networks, dedicating one to 802.11b/g clients (BT) & another to 802.11n clients (AEBSn). With the AEBSn bridged, clients on either network can still "see" each other for sharing.
How easy is it to set up a bridge on Airport Extreme?
Very; you would just need to use the AirPort Utility to make, at least, as single setting change to do so. (ref: Connection Sharing = Off (Bridge Mode))
And also, will using my BT Home Hub instead of say a Netgear Modem slow my overall internet connection / wireless speed down?
Your Internet connection speed is not controlled by the modem. Instead, it controlled by your ISP and affected by the current Internet traffic conditions. However; the router does affect the local network speeds.
Happy New Year!
Maybe you are looking for
-
I'm using reports 6i and have what I think is a simple report requirement but I'm unable to set the properties to get it to report correctly... I have a report where I would like to print one record per page (essentially a form letter). The page is d
-
How do I merge events on the new IPhoto. The old one was simply drag and drop, this one will not.
How do I merge events on the new IPhoto. The old one was simply drag and drop, this one will not.
-
Logical expression OR not working
Hello Experts, I am using logical expression 'OR' but the current statement does not seems to work. Is my statement correct ?? Is there something else which I can use in place of 'OR'?? if R1_NO EQ 'X' DELETE itab_abapcode from n3 to row_end_even
-
Selection variables upon opening workbook
Hi experts, I have a workbook, which has 2 queries in seperate excel sheets. I have set the property to refresh upon opening under the property selection > All work books. Additionally I have enabled to show last refresh date and Status date for the
-
I have been on Option3 for years and assumed I was covered by Bt Security, Only now when I decided to check the position of my cover did I find I had no security at all. However I got the following notice: We've detected you're using a computer ru