Airport Extreme 802.11n gone after firmware update

Started Airport Utility earlier today, just to check a password. An Apple window came up offering new firmware, 7.1.1, I think. I usually accept these offers without thought, so I let the update run. Now Airport Utility cannot detect the Airport Extreme (802.11n). The support page says to check for software up dates, but there were none.
What next?

Hello pmacdd. Welcome to the Apple Discussions!
First, try quitting, and then restarting the AirPort Utility, and then, try accessing the AEBSn.
If this doesn't solve the problem, then try connecting your computer directly, using an Ethernet cable, to one of the LAN ports of the AEBSn and then try accessing the device.

Similar Messages

  • How do I know if my airport Extreme 802.11n needs updated firmware based on heart bleed issue using Mavericks?

    I have Mavericks on oour laptops. I have an Airport Extreme 802.11n WI-FI not sure when I bought it. THe article by Tim Cook and Heartbleed issue is very technical and only mentions Leopard operating system. So do not know if I need to upgrade firmware or not. Not sure I undertand "Back to my Mac" or what to do? Also have an airport express.

    it doesn't
    only the newer AC/tower designed models required the updated firmware

  • USB Printing AirPort Extreme 802.11n

    I've upgraded to the new AirPort Extreme 802.11n base station and am having troubles printing to printers that worked fine with my previous AirPort Extreme 802.11g base station.
    Both USB printers are detectable for set-up in the Print & Fax Preference tab and can be printed to when hooked directly to my computer. They are also detectable for set-up in the Print & Fax Preference tab when hooked via the base station.
    So, all set-up and settings are fine. The issue I am having which never occurred before is that the file is sent to the queue but is immediately labeled as stopped and will not print no matter what I try.
    I've configured, reconfigured, reset,you name it but with no luck.
    does anyone have any answers out there. Please help...

    I have had the same issue repeatedly after upgrading to Leopard. I can no longer use my printer (Brother HL-2070N the "network ready one") with my airport extreme router. It used to show up before I updated to 10.5.2, now I can't even get it to show up at all. I reset the base station, unplugged, and then re-plugged in the printer, nothing worked. Then I tried to just delete it from my list of printers and re-add it, but now my computer can't find it! I didn't change anything on my network at all, and I had literally printed something just 10 minutes before I applied the update. Very frustrating for a $180 router.

  • I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but the printer won't work with the new one.

    I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but I'm having trouble with the new one. When I try to print, I get a USB Waiting message on the printer, and when I force a page to print by pressing Go on the printer, I get a page that says ERROR: syntaxerror OFFENDING COMMAND: true.  . . .cvt . . . fpgm . . . x . . .lglyf . . . <..J head . . .     STACK: / [    -mark-   /sfnts I’ve tried shutting down the printer and disconnecting it and the Airport, but that doesn’t help. I reset the settings on the printer. I upgraded the Airport firmware and removed, reinstalled, and upgraded the Lexmark printer driver. After I upgraded the firmware and printer driver, a few pages printed correctly, but then I got the same syntax error page as before. Any suggestions for getting the printer to work correctly?

    Use a powered USB hub between the AE and the printer.. the usb port does sometimes have issues.
    Try deleting the printer in the Mac and reinstall it.. the change in AE can represent effectively a change of printer.. it is important to make sure that is all up to date.
    Beyond that.. USB printers.. ughhh! Consider for two toners you can go and buy a proper network printer.

  • Airport Extreme 802.11n (4th Generation) vs. MBP 2006.  The MBP is losing :(

    GRRRRRRRRR— I feel like this is a version of a problem I see repeated here endlessly, but none of the threads I see about it is quite the same, or fixes my problem.       We have a network with:
    Airport Extreme 802.11n (4th generation), connected to DSL modem.  Firmware 7.5.2
    MBP 2006, running OS 10.6.7 ****
    MBP 2008, running OS 10.5.x
    ipads, iphone, shared printer, drive, etc.
    Everything works fine EXCEPT the MBP 2006.  It connects to the network, works for a while, and then after a certain amount of time (anywhere between a minute and several hours) it's dropped.  The menu bar still shows a connection and full signal, but there's no connection (TCP or afp) and when I launch the Aiport Utility, it just says that no base stations can be found.   The menu bar seems to be lying. Using the menu to turn Airport off and back on (or sleeping the laptop) works to reestablish the connection.
    I do not have this problem with the MBP 2006 on other wireless networks (at work, or at my other home in another city).  Just with the Airport Extreme
    I've tried changing the channels, disabling IPv6 on the laptop and on the Airport Extreme, setting up a manual DHCP address, and changing the setting for "radio mode" of the base station from Automatic to 802.11a/n - 802.11b/g/n.   I also read that there might be troubles with "mixed" networks with both 802.11g and 802.11n, so I upgraded the Airport card in my MBP 2006 to an AirPort Extreme 802.11 a/b/g/n, which made disk sharing much faster when it's working, but didn't put an end to the cut-outs
    Hjalp?  Why does the Airport Extreme keep dropping my MBP 2006 (or vice versa)?  Are there other things I should be changing or disabling?

    OK, two possible leads:
    1) Using the AirPort Utility, I disabled 802.11n, setting the AirPort Extreme to b/g only.  This seemed to help— I didn't fall off the network all afternoon.  (Setting it to 'n' only did not work, unfortunately, or else that would have been better, since it would have let me take advantage of the faster speeds for Time Machine to the shared disk)
    2) Soon thereafter, for seemingly independent reasons, we starting having trouble with our DSL connection.  We reset the AEBS to factor settings, which didn't solve the DSL problem (had to get a Windstream technician out for that), but since that reset, I've been connected with 802.11a and the MBP hasn't fallen off the wireless network once.
    We'll see how it holds up, but for now, the recommendation seems to be first to reset the AEBS settings to factory default, and then try disabling 802.11n...

  • Is my AirPort Extreme (802.11n) Base Station defective?

    I'm trying to set up a wireless network with my new AirPort Extreme (802.11n) Base Station. I dismanteld my existing network that consisted of an old model AirPort Extreme and an AirPort Express. I can't seem to get anything to work properly with the new hardware. I have a G4 Quicksilver that uses an AirPort card. Is that the issue? I thought they were compatible. I was not able to update the Setup Utility because I don't have an Intel Mac. Still, that shouldn't prevent me from doing an initial setup. I'm thinking perhaps the unit is defective. I've been working on this several hours a day for almost a week. This is the most trouble (by far) that I've ever had with any Apple product. I'm really disappointed. I suspect the hardware is defective, but based on all of the issues I've read about in this forum, I think it could just be reflective of the poor overall quality of the new AirPort Extreme. What a let down.

    What is the exact name of the application you are using to configure the airport?
    You should be using "AirPort Utility"
    It is a Universal application, so it should work on both a PPC and Intel mac.
    As for the update, if you can't download it via software update, you most likely do not need it.
    The quicksilver only has an Airport card:
    http://support.apple.com/specs/powermac/PowerMac_G4_Quicksilver2002.html
    That means that you will need to configure the airport extreme N to operate in the 2.4 GHz range. You will need to tell it that it needs to be compatible with 802.11b
    There is probably an option for 802.11 b/g/n compatibility.
    Are you going to still use your airport express? you could either use WDS to extend your wireless network without connecting the two airport base stations with an ethernet cable... or you could connect them together with an ethernet cable and configure the same network name and use two different channels (only use 1, 6, or 11). If you extend a network, they both need to use the same channel.
    If the quicksilver is the only machine on your network, it will not be any faster.
    Actually, you could make things faster, now that I think about it... I am guessing that your quicksilver is not located near your airport extreme. If I am wrong, just ignore this...
    You could use one of your airports as your main base station, connected to your cable modem/dsl whatever... then you connect the other airports ethernet to your quicksilver. you then turn off the airport card in your quicksilver and set up the airport connected to your computer to use WDS and connect to the other airport using 802.11g.
    You now have gone from an 11 mbps max (5 mbps real world) connection to a real world 30-40 mbps link.
    Other options would be to look for 802.11g or 802.11n usb adapters for the quicksilver... I am not sure what is mac compatible out there, since it is probably a small market since it is built in to all new macs.
    Good luck

  • Airport Extreme 802.11n Base Station blocking RealPlayer 11 completely

    I am trying to play this radio station (just a brasillian sports channel) on RealPlayer 11:
    rtsp://real.rbsonline.com.br/liverbs/*/broadcast/rdgaucha/gaucha.rm
    Which is completely blocked on my Airport Extreme 802.11n Base Station with the latest firmware update.
    It even blocks when RealPlayer is configured for HTTP only.
    I am using it on my iMac which is connected directly via a ethernet cable instead of wifi to the Airport Extreme 802.11n Base Station.
    RealPlayer can play it fine when I plug my iMac directly to the cable modem so it proves is the router. I never had RealPlayer issues before when I was using a linksys router.
    It does really feel like Apple put an intentional block on RealPlayer to stop competition.
    Anyone seen this issue? Guess it is related with the BBC RealPlayer issue.

    Fixed myself, problem was because I setup OpenDNS on base station, removed it now works

  • Airport Extreme 802.11N (5th Gen) frequent crash

    I had bought an Airport Extreme 802.11N (5th Gen) that died a few months after purchasing it. I had the unit replaced via Applecare in May 2013.
    The new unit's firs recorded crash was in August 2013. After that, it crashed sporadically, these instances were not recorded. In May 2014 it crashed twice in one day. Every time of a crash, I've had to effect a hard reset to factory presets and upload a saved configuration. This last time I reconfigured from scratch and saved the new config. Now it crashes regularly, every month since September. I have no idea what to make of it.
    Considering that I had one of the original Silver units running for years (and upgraded with a more capable Orinoco card—if you know what I'm talking about, you know that's old!). I expected to get reliable service from this more advanced unit. So far, It's a bit of a dud.
    Any ideas? Any diagnostic tools I can use to see what's happening? Does this run of Airport Extremes have "issues"? Should I bother getting one of the new tallboy unit?
    Thanks.

    I have found the Gen5 AE to be very reliable.
    I would have blamed a dud unit.. except that you have had two of them.. So I would be tracing where the problem is apart from the AE.
    What modem do you run? How is the AE setup in the network?
    The older utility is of far more use than the one in Yosemite. So do you have available an older OSX version or even windows.. you can see the logs from the unit.. just like you could in the original B and G versions.
    (and upgraded with a more capable Orinoco card—if you know what I'm talking about, you know that's old!
    Know exactly what you are talking about.. Orinoco were most desired for their use with wifi scanners.
    How is your power?? Apple stuff does seem to use stuff that is highly susceptible to spiking. I keep my network stuff on UPS. (or battery direct feed).
    I also do not like 7.6.4 firmware.. I know others here might find it ok but I can clearly demonstrate worse performance with it. Direct A-B testing.
    Take the firmware back to 7.6.1 and factory reset and see if you get any improvement.
    To actually need to restore firmware settings is not normal.. so something major is wrong and in unusual way.. I think power is one key part of it.

  • AirPort Extreme (802.11n) & Epson CX3100 Printer Problem

    I recently purchased the new AirPort Extreme 802.11n and tried hooking up my Epson Stylus CX3100 to it. It detects the printer but it only prints the first few lines then stops. I check the status window of the printer and I see no error message whatsoever. I have to turn off the printer to force the paper out. The printer prints fine when connected directly to the iMac.
    I was using the Gimp printer driver found in my iMac. Since that didin't work, I tried installing the new Intel drivers from Epson. But when I try adding it to me AEBS using the official driver, I get an Error: -9672 message.
    I've already updated my AEBS's firmware to 7.1 before I tested the printer, so I'm not sure if it's a firmware issue.
    Any help would be greatly appreciated.

    Jgrboer wrote:
    I try to setup my network with an Airport Extreme FW7.5.1 (from 2010), an Airport Express FW7.4.2 (from 2010) and an Imac.
    Your iMac isn't receiving an IP address at all - the 169.254.x.x is "self-assigned" and indicates it is not receiving the IP address from any router. That won't work.
    I'm not sure what you intend to do with the Express so leave it unplugged for now. Use Airport Utility, select your Airport Extreme, click "manual setup", then click the Base Station tab. Note the name of the wireless network it's creating.
    Then click the Wireless tab. Make sure the Wireless Mode set to "create a wireless network". Next, consider using no Wireless Security at all, until you've sorted out your problems.
    Next, click the Airport pane, then click the Internet pane, then click the Internet connection tab. Next to "Connection Sharing" select "share a public IP address".
    Click the TCP/IP tab. Configure IPv4 "using DHCP".
    Click Update and let it restart.
    Make sure your iMac is connected to the wireless network created by your Extreme. It should then get an IP address of 10.0.1.1 and you should be able to connect.
    If this works then we can configure your Express to do whatever you want it to do. If it doesn't work write back and we'll try to figure out what's wrong.

  • Timed Access not working on new Airport Extreme (802.11n).

    I bought a new Airport Extreme (802.11n) to use as a router for my network. The network has a mixture of Macs and PCs, using a mixture of wired and wireless connections.
    I configured the security settings with on the Airport Extreme to Timed Access. I set the default setting is to No Access.
    Three computers are set with "Everyday, Between 8:00am and 11:00pm"; however, when it's 11:00pm, nothing happens. The three computers continue to have access.
    I know the MAC addresses I entered are correct. Does anyone know why the Timed Access is not working?

    Yes, the printer was initially set the same way it always was on my old router. It used to pop right up on the list. After I switched I was getting communication errors. Ok, new setup, I wasn't worried yet. When I got to the setup window and it a new printer wasn't found I tried updating drivers. No luck. I then used the IPP mode to enter the IP address with the address on the Canon screen. It failed. I then did the same setup telling it which software from the driver list to use. It still could not see it. The odd part is that the Canon can obviously  see the router as its LAN setting read active and it is receiving the IP. I have proceeded to play with every setting on the printer and it is back to factory reset. Oh, I should mention that I have also tried to use Canons network setup utility software and it can not find the connection either. So I really think this is a problem within the router. I have seen many complaints about this on other forums, but most were looking to use the usb on the print server. My Airport is nowhere near my printer and I don't want to lose my all-in-one functions. Some think hard lined ethernet is ancient, but it really is a nice setup. Fast and reliable.

  • AirPort Extreme (802.11n)  - Which draft version of 802.11n does it use?

    When the new AirPort Extreme 802.11n was announced, Apple didn't specifically state which version of the 802.11n draft it was using.
    At the time of the announcement, version 2 of the 802.11n draft had not been submitted yet for approval.
    So my question is what version of the Draft-N spec is it using?
    1.0?
    2.0?

    As I understand it, the big change was going from a single 40 MHz channel to dual 20 MHz channels because some b/g base stations would get confused by 40 MHz channels, causing problems on their networks.
    Here's a link to a Computerworld column about the new draft, which pretty much confirms that it's only a firmware update:
    http://www.computerworld.com/action/article.do?command=viewArticleBasic&articleI d=9008825

  • How do I connect my Airport Extreme 802.11n to Epson 645 Printer?

    I can't figure out how to connect my Airport Extreme 802.11n to my Epson 645 Printer.  Can anyone help me?  Thanks!

    You may want to try reinstalling Mavericks. Airport Utility installed by Mavericks may no longer connect to your older AEBS (though I've not heard that.) Installing the Old AirPort Utility (Version 5.6) on Mountain Lion | frank.is.
    Reinstall Lion, Mountain Lion, or Mavericks
         Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
         COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and
         after the chime press and hold down the OPTION key until the boot manager screen appears.
         Select the Recovery HD and click on the downward pointing arrow button.
         Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu.
         Repair the Hard Drive and Permissions as follows.
    After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
         Reinstall Lion/Mountain Lion, Mavericks: Select ReinstallLion/Mountain Lion, Mavericks from
         the Utilities menu, and click on the Continue button.
         Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
                    three times faster than wireless.

  • Help needed connecting Iomega Minimax Ext HDD to Airport Extreme 802.11n

    Would appreciate if someone can help me with the following task. After researching and trying several things, I have not succeed in resolving the issue.
    I want to connect a Iomega MiniMax Ext HDD (for Mac) to my (Airport Extreme 802.11n + Time Capsule) box using the USB port at the back of my Airport Extreme. Then I want to access the Ext HDD wirelessly as a drive on my Macbook (snow leopard OS). I was told this was possible at the Apple Store...but have failed so far.
    Any suggestions so far

    Hello smitra. Welcome to the Apple Discussions!
    The following are the basic steps for sharing an external USB drive attached to either an 802.11n AirPort Extreme Base Station (AEBSn) or a Time Capsule (TC):
    o Plug the hard disk into the USB port on the back of the base station.
    o Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac, and in Start > All Programs > AirPort on a computer using Windows
    o Select your base station, and then, choose Manual Setup from the Base Station menu.
    o Click Disks in the toolbar, and then, click File Sharing.
    o Choose “With a disk password,” or “With base station password” if you want to secure the shared disk with a password, or choose “With accounts” if you want to secure the disk using accounts. If you choose to use accounts, click Configure Accounts, click the Add "+" button, and then enter a name and password for each user that will access the disk. For simplicity, I would recommend using the "With a disk password" option.
    o Choose “Not allowed,” “Read only,” or “Read and write” to assign guest access to the disk.
    o Select the “Share disks over Ethernet WAN port” checkbox if you want to provide remote access to the disk over the WAN port.
    You should now be able to find this drive within Finder under the SHARED category.

  • To extend AirPort Extreme 802.11n

    Wanting to extend the range of my AirPort Extreme 802.11n (version 7.4.2)
    I have a Airport Express as trial also a 802.11n. AirPort Utility has a lot of trouble finding the Express. When AirPort Utility does find it and I want to set up the Express I have to switch from the Extreme to the Express. Unfortunate side-effect is that AirPort Utility then looses track of the Extreme and I can't "join" the Express as Utility can't find anything to join.
    As I have the Express on trial of a friend I did the normal reset (button for 10 sec) and even the factory reset (unplug, press reset button while plugging in) however I did notice it still had his settings. Changed those but as I said before it seems for AirPort Utility is is either or instead of both.

    Based on your description, it sounds like the AXn is configured to join the wireless network created by the AEBSn ... not extend it.
    The following would be the basic setup steps for extending a wireless network:
    o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
    o Open AirPort Utility and select the base station that will connect to the Internet.
    o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
    o Click AirPort in the toolbar, and then click Wireless.
    o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
    o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
    o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
    o Enter the base station network and base station password is necessary.
    o Click Update to update the base station with new network settings.
    (ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

  • AirPort Extreme 802.11n as a wireless router and local network switch?

    Good afternoon,
    I'm curious if its possible to have the APE in wireless network mode and connect systems via hard line as well?
    I have an AirPort Extreme 802.11n set to "Create a Wireless Network" mode that is attached directly to a cable modem for internet connectevity. My issue is that while all wireless devices (several iPods, two iPhones and three laptop computers) connect to the APE without issue (and have internet access), when I try to plug in a Windows 7 desktop computer via one of the ethernet jacks, Windows is unable to connect and shows the network as "unidentified," spitting back a private IP address as opposed to a local LAN (this behavior repeats for an Ubuntu Linux box as well).
    Not sure if the APE is misconfigured, this is a Windows 7 issue or if its improper use on my part (though this also precludes me from connecting a gigabit switch to the APE).
    Thank you,
    Nathan

    Properly configured, the AirPort should provide both wired and wireless network client with Internet access.
    At this point, I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Continue with step 2 in the first set of steps.
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Maybe you are looking for