Airport Extreme 802.11n setup done but get disconnected randomly

Dear friends,
I have AirPort Exteme 802.11n WIFI
I did complete set up as per the manual. I set up to use as Extended Network to my existing network.
My PC is window 7 operating system and is updated. I reset my router also.
After connecting to my existing network via LAN and complete setup, network available on my iphone 5
Then I remove LAN cable, it keep ON for 2 or less hours and then gets disconnected and the Amber light on Airport starts blinkin.
I did set up after default setting also.
Please advise.
Regards,
Jayant Joshi

Similar Messages

Airport Express 802.11n + Airport Extreme 802.11n 2.4ghz but not 5ghz?

I can't get my Airport Express 802.11 to extend the network of my Airport Extreme 802.11n using 5Ghz only... but it will work with "n only 2.4Ghz"....
any solutions?
Message was edited by: Eric Carpenter

Addtional info both AE's now have ver 7.5.2 installed, prior it was 7.6 and situation is still the same.

How do I get a download since I don't have my start up disc for AirPort Extreme 802.11n

How do I download to start using AirPort Extreme 802.11n. I can't find my start up disc. and don't see any downloads on Apples website. Then how do I hook it up to work with my Westell modem?

Please download and install AirPort Utility 5.6.1 for Windows. The Windows Firewall and or Microsoft Security Essentials will tend to block the connection from your PC to the AirPort Extreme, so you may need to adjust the firewall settings on the PC or check the Essentials application if connection difficulties occur.
AirPort Utility 5.6.1 for Windows - Apple Support
Use the Setup Guide to install and configure the AirPort Extreme
AirPort Extreme Setup Guide - Support - Apple

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The wireless router works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The Airport works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

+For now I have it set to Share Public IP address - Is this correct for my Network Setup with The Airport Extreme being the only router being used ?+
This would be the correct setting if the AirPort Extreme is connected to a simple modem (one ethernet port).
*Settings I have Enabled*
5 GHz name indicates that you have elected to use the option to assign a separate name to the 5 GHz network. This will allow you to "tell" compatible computers to connect to that network, rather than the slower 2.4 GHz network
Use Wide Channels is recommended for 5 GHz operation.
Interference Robustness often does more harm than good and should not be used unless you know you are in a area with a lot of wireless networks and you feel that your network is experiencing interference issues from a nearby network.

I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

I'm not sure how to post a message. I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I have an older Airport Express, would it help to install it? would it work best if it was installed in the same room? should it be installed half way in between? Get another Extreme? The Mac Book Pro on the middle floor can see 11 networks in the neighbourhood if that might be causing a problem or would if I installed the Express. Thank for your consideration.

Thanks for your time ... I appologize for the font and colour, I compossed the question in pages and failed to notice the font colour as grey ... there are a variety of computers of various ages so I think it is using a setting that allows both 5G and 2.4 ... the connection to the Airport is thru a cable modem and cable does run throuhout the house ... maybe those hard wires would be a place to look at ... do you think that putting the 'Express' on the second floor might help ... thanks again ...

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but the printer won't work with the new one.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but I'm having trouble with the new one. When I try to print, I get a USB Waiting message on the printer, and when I force a page to print by pressing Go on the printer, I get a page that says ERROR: syntaxerror OFFENDING COMMAND: true. . . .cvt . . . fpgm . . . x . . .lglyf . . . <..J head . . . STACK: / [ -mark- /sfnts I’ve tried shutting down the printer and disconnecting it and the Airport, but that doesn’t help. I reset the settings on the printer. I upgraded the Airport firmware and removed, reinstalled, and upgraded the Lexmark printer driver. After I upgraded the firmware and printer driver, a few pages printed correctly, but then I got the same syntax error page as before. Any suggestions for getting the printer to work correctly?

Use a powered USB hub between the AE and the printer.. the usb port does sometimes have issues.
Try deleting the printer in the Mac and reinstall it.. the change in AE can represent effectively a change of printer.. it is important to make sure that is all up to date.
Beyond that.. USB printers.. ughhh! Consider for two toners you can go and buy a proper network printer.

I just purshased AirPort Extreme 802.11n wi-fi I was told to get the step by step direction on the internet and I am not able to find it can you help me

I just purchased AirPort Extreme 802.11n wi-fi I was told to get a step by step direction to install this wi-fi on line but I am not able to find it. can you please help me?
Helen

See this Apple video tutorial.
http://www.apple.com/findouthow/mac/#wirelesssetup
And this Apple doc:
http://manuals.info.apple.com/en_US/airport_extreme_5th_gen_setup.pdf

Is my AirPort Extreme (802.11n) Base Station defective?

I'm trying to set up a wireless network with my new AirPort Extreme (802.11n) Base Station. I dismanteld my existing network that consisted of an old model AirPort Extreme and an AirPort Express. I can't seem to get anything to work properly with the new hardware. I have a G4 Quicksilver that uses an AirPort card. Is that the issue? I thought they were compatible. I was not able to update the Setup Utility because I don't have an Intel Mac. Still, that shouldn't prevent me from doing an initial setup. I'm thinking perhaps the unit is defective. I've been working on this several hours a day for almost a week. This is the most trouble (by far) that I've ever had with any Apple product. I'm really disappointed. I suspect the hardware is defective, but based on all of the issues I've read about in this forum, I think it could just be reflective of the poor overall quality of the new AirPort Extreme. What a let down.

What is the exact name of the application you are using to configure the airport?
You should be using "AirPort Utility"
It is a Universal application, so it should work on both a PPC and Intel mac.
As for the update, if you can't download it via software update, you most likely do not need it.
The quicksilver only has an Airport card:
http://support.apple.com/specs/powermac/PowerMac_G4_Quicksilver2002.html
That means that you will need to configure the airport extreme N to operate in the 2.4 GHz range. You will need to tell it that it needs to be compatible with 802.11b
There is probably an option for 802.11 b/g/n compatibility.
Are you going to still use your airport express? you could either use WDS to extend your wireless network without connecting the two airport base stations with an ethernet cable... or you could connect them together with an ethernet cable and configure the same network name and use two different channels (only use 1, 6, or 11). If you extend a network, they both need to use the same channel.
If the quicksilver is the only machine on your network, it will not be any faster.
Actually, you could make things faster, now that I think about it... I am guessing that your quicksilver is not located near your airport extreme. If I am wrong, just ignore this...
You could use one of your airports as your main base station, connected to your cable modem/dsl whatever... then you connect the other airports ethernet to your quicksilver. you then turn off the airport card in your quicksilver and set up the airport connected to your computer to use WDS and connect to the other airport using 802.11g.
You now have gone from an 11 mbps max (5 mbps real world) connection to a real world 30-40 mbps link.
Other options would be to look for 802.11g or 802.11n usb adapters for the quicksilver... I am not sure what is mac compatible out there, since it is probably a small market since it is built in to all new macs.
Good luck

Timed Access not working on new Airport Extreme (802.11n).

I bought a new Airport Extreme (802.11n) to use as a router for my network. The network has a mixture of Macs and PCs, using a mixture of wired and wireless connections.
I configured the security settings with on the Airport Extreme to Timed Access. I set the default setting is to No Access.
Three computers are set with "Everyday, Between 8:00am and 11:00pm"; however, when it's 11:00pm, nothing happens. The three computers continue to have access.
I know the MAC addresses I entered are correct. Does anyone know why the Timed Access is not working?

Yes, the printer was initially set the same way it always was on my old router. It used to pop right up on the list. After I switched I was getting communication errors. Ok, new setup, I wasn't worried yet. When I got to the setup window and it a new printer wasn't found I tried updating drivers. No luck. I then used the IPP mode to enter the IP address with the address on the Canon screen. It failed. I then did the same setup telling it which software from the driver list to use. It still could not see it. The odd part is that the Canon can obviously see the router as its LAN setting read active and it is receiving the IP. I have proceeded to play with every setting on the printer and it is back to factory reset. Oh, I should mention that I have also tried to use Canons network setup utility software and it can not find the connection either. So I really think this is a problem within the router. I have seen many complaints about this on other forums, but most were looking to use the usb on the print server. My Airport is nowhere near my printer and I don't want to lose my all-in-one functions. Some think hard lined ethernet is ancient, but it really is a nice setup. Fast and reliable.

New Airport Extreme (802.11n): : Port Mapping... ***???

There are two different programs I was formerly using, whereby (after following instructions) I was able to create a static IP address for every machine on my network, plus open ports 8000 and 9990-9998 respectively. But ever since upgrading to the new Airport Extreme (802.11n), it completely stopped working. To boot, I've upgraded to Leopard on one of two of the machines (the other is still using 10.3.9).
I haven't been able to figure out for the life of me, how to configure it. It's no longer as obvious where and what information to put in. All guides that would remotely help are designed for the older Airport unit, which has completely different menus in the Airport Utility.
Is there anyone out there who has experience with Dot-Tunes and/or Nicecast or similar port mapping, who has the patience to describe, in layman's terms, what steps to take to get this set up correctly again, starting with how to reassign static IPs for my machines. I will not ask a lot of questions and take up too much more of your time. I'm just frustrated after a whole day of trying to figure this out and fruitless Google and forum searches.
Thank you so much.

I'm not familiar with either Dot-Tunes or Nicecast, but the following would be the general port mapping procedure with the 802.11n AirPort Extreme Base Station (AEBSn) using the AirPort Utility. Note in this procedure you will not need to assign a static IP address for each of your host devices. Instead you will be taking advantage of the AEBSn's DHCP reservations feature.
To setup port mapping on an AEBSn, either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

To extend AirPort Extreme 802.11n

Wanting to extend the range of my AirPort Extreme 802.11n (version 7.4.2)
I have a Airport Express as trial also a 802.11n. AirPort Utility has a lot of trouble finding the Express. When AirPort Utility does find it and I want to set up the Express I have to switch from the Extreme to the Express. Unfortunate side-effect is that AirPort Utility then looses track of the Extreme and I can't "join" the Express as Utility can't find anything to join.
As I have the Express on trial of a friend I did the normal reset (button for 10 sec) and even the factory reset (unplug, press reset button while plugging in) however I did notice it still had his settings. Changed those but as I said before it seems for AirPort Utility is is either or instead of both.

Based on your description, it sounds like the AXn is configured to join the wireless network created by the AEBSn ... not extend it.
The following would be the basic setup steps for extending a wireless network:
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

AirPort Extreme 802.11n as a wireless router and local network switch?

Good afternoon,
I'm curious if its possible to have the APE in wireless network mode and connect systems via hard line as well?
I have an AirPort Extreme 802.11n set to "Create a Wireless Network" mode that is attached directly to a cable modem for internet connectevity. My issue is that while all wireless devices (several iPods, two iPhones and three laptop computers) connect to the APE without issue (and have internet access), when I try to plug in a Windows 7 desktop computer via one of the ethernet jacks, Windows is unable to connect and shows the network as "unidentified," spitting back a private IP address as opposed to a local LAN (this behavior repeats for an Ubuntu Linux box as well).
Not sure if the APE is misconfigured, this is a Windows 7 issue or if its improper use on my part (though this also precludes me from connecting a gigabit switch to the APE).
Thank you,
Nathan

Properly configured, the AirPort should provide both wired and wireless network client with Internet access.
At this point, I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

AirPort Extreme (802.11n) dual band is reporting problems?

Hi.
I can not find an answer for my error-problem:
AirPort Extreme (802.11n) dual band is reporting problems!
I have an optimum on line cable modem connected to my AirPort Extreme (802.11n) dual band.
Ethernet cables connect it 1. into my new Nehalem Mac Pro, 2. into my back-up Quicksilver PowerMac. I also have 2nd gen. iPod touch works on WiFi.
This set-up has been working well but now I daily get the above error. Sometimes it says also: You have different locations set-up and it asks me to go through the set-up procedure. May be I did the initial set-up incorrect. I don't quite understand "locations" and it's purpose.
Also the Airport runs very hot so I put a small fan in front of it. A few times I had to disconnect the cable mains to reset and get back my service. Please help.
W.W.

Walter Wedler wrote:
AirPort Extreme (802.11n) dual band is reporting problems!
I have an optimum on line cable modem connected to my AirPort Extreme (802.11n) dual band.
Ethernet cables connect it 1. into my new Nehalem Mac Pro, 2. into my back-up Quicksilver PowerMac. I also have 2nd gen. iPod touch works on WiFi.
This set-up has been working well but now I daily get the above error. Sometimes it says also: You have different locations set-up and it asks me to go through the set-up procedure. May be I did the initial set-up incorrect. I don't quite understand "locations" and it's purpose.
Can you tell what's telling you about those locations? An Apple AirPort unit can maintain different "configurations" so that it could be used in different locations without a complete reconfiguration. However, I don't believe they're ever referred to as "locations". On the other hand, a Mac can have multiple "locations" defined in the Network panel of System Preferences. Those can be useful if the Mac is used in different places with different arrangements.
If your AirPort Extreme is having problems the status light on the front will probably be amber. If you launch AirPort Utility and double-click on the AirPort Extreme item on the left, you should be able to see more details about the problem.

Airport Extreme 802.11n Wi-Fi not working

I just purchased Apples Airport Extreme 802.11n with the idea of getting just a bit more range than my old airport. This is/was hard to tell since I could not get the unit to function properly.
My internet service requires two address but this A/P Extreme only allowed one. This A/P Extreme 802.11n totally shut down my internet service. It did not allow wireless connection with other computers. The range seemed to be less than my older Airport Extreme 802.11 a/b/g.
I had to re-install my Airport Extreme a/b/g to get things working again.
I went to Apples Products and Service page to find out about the Express registration. Apples registration system did not recognize my serial number. Apparently their specification page recognized some parts of the serial number since the web page did display specification for the Airport Extreme.
DOES ANYONE KNOW THE REASON FOR ALL OF THIS TO HAPPEN?

You said you went to the "Express" page and tried to register above. It may be because you tried to register an Extreme as an Express. I had some difficulty over two months ago registering my Extreme. It let me register it without all the data because it would not recognize the serial number. Called Apple Care and they made sure it was registered.
Also, unless you have an all 802.11n system, you may get a little more range out of the Extreme, but I don't think any more than if you would have used an Airport Express 802.11g. Range and speed are geared toward all n systems.

AirPort Extreme 802.11n and PowerBooks?

I am about 1.5 seconds away from buying one of the new AirPort Extreme 802.11n base stations to work with my AirPort Express but I have some questions / concerns.
1) Is my Powerbook capable of being enabled to access an "n based network" or is my money wasted on a router capable of speeds my computer can not access?
2) Should my computer be capable of accessing this network, is the Airport Express Base Station I have capable of acting on this network in "N speed" too? I know the base station can be configured to act essentially as a relay to boost signal strength...if set up to do so will it dumb the speed down to "G speed"?
3) If 1 and 2 are true and the express base station dumbs the speed of the N router down, can I configure the airport express base station to ONLY act as a wireless conection to my stereo and not as a wireless router, so as to allow my Powerbook to access the "N" speed network but still broadcast my music wirelessly to the stereo?
Many thanks...I wish they just made this information clearer on pages like this:
http://store.apple.com/1-800-MY-APPLE/WebObjects/EducationIndividualCanadaCustom .woa/9804006/wa/PSLID?mco=F7D93AEF&nplm=D4141ZM/A&wosid=gE4h0LIBbghZ2sXpLP21Wij0 uPJ

Hey for any one still lookin....
1. It all depends on what your CARD is capable of. Your POWERBOOK is more then capable of "N" speeds. Your only limited on the bandwidth of the Cardbus slot. You would have to have a third party card to access the new "N" speeds tho. I'm not sure if the last batch of (pre MacBooks) Powerbooks even made it to the "G" standard. I know Apple just came out with a driver for the latest Macs that have an upgradeable Card and or Basestation to get to "N". I really don't think your Express is upgradeable.
2. You need to look at what models you have to figure out what their capable of. You should be able to go to Apple's web site to find out. Usually the Router will Dumb it down to the SLOWEST speed. Unless you were streaming your music, and playing a game online, and transferring a large file you shouldn't have a problem anyway. As long as you are not using the slowest product it won't dumb down.
3. Haven't got that far yet. I've used up all my brain cells getting this far, so good luck on your mission. Try starting another string with specifics on what you want to do.

Airport Extreme 802.11n setup done but get disconnected randomly

Similar Messages

Maybe you are looking for