Airport extreme and connection to imac

I bought a new imac with intel processor yesterday but i am having problems getting connected to the internet wirelessly.
i have a belkin pre n wirless router to which are connected a pc and a laptop both running windows xp via a cable modem.
The room where i want to use the imac seems to be a blackspot for the wifi signal in our house (the laptop wont work there either). I was told by the store that an airport express would be able to act as a booster for the signal but it appears to me that it will only act as a booster for a system that uses a Airport extreme base station. Is that the case ??
I also need to be able to connect my windows pc and laptop to my internet connection and home network. If i do get a Airport Extreme base station will i be able to connect these to it and also use the belkin wireless card in the laptop to connect.
Any advice would be really appreciated.
Thanks
Imac 2ghz Intel 250g hard drive Mac OS X (10.4.4)

Similar Messages

Airport Extreme and connecting a hard drive

Hello All,
Thank you ahead of time for your help! I have a couple of questions regarding the set up of my airport extreme and an external hard drive.
What I want to accomplish is using the airport extreme to ONLY share a hard drive for backup and sharing other files through out the house. My housemates already have the internet going through their router, so there is for the airport extreme. Can a macbook pro (13in intel) receive two wireless signals, one that is the internet and the other from my airport extreme (that shares my hard drive)? If so, how is this done?
Any assistance would be more that appreciated!!
Thanks!!

Hello njoza. Welcome to the Apple Discussions!
The simplest way to accomplish this would be to connect the 802.11n AirPort Extreme Base Station (AEBSn) to the Internet router by Ethernet; reconfigure the AEBSn as a bridge, and disable its wireless radios.
In this configuration, you can still share out the hard drive and only need to connect to the Internet router's wireless network for both drive & Internet access.

2wire wireless- Airport Extreme- ethernet connection to iMac - how?

I have AT+T's DSL router that has wireless capabilities (802.11g, not n). I'm trying to use the new (802.11n version, although I'm not using n for this obviously) airport extreme to extended my wireless network to give me a wired access point to my old iMac (no wireless card).
So far the best I can do is get the airport extreme on the wireless network with a green light, but I can't get a wireline connection to land on this network. I'd even be ok with the airport extreme was a router that made the wired ports on a different network that would then route out to the wireless network.
When I connect a wired device to the airport extreme, it comes up with a 169.254.94.121 address. The wireless network is 192.168.1.x. The airport extreme does get it's 192.168.1.68 address on the same network as the 2wire. I've even forced my iMac into having an 192.168.1.80 address, but it can't ping the airport extreme's 192.168.1.68 address, so obviously the airport extreme isn't behaving how I would like. I even fired up WireShark on the connection, but it looks like the airport extreme won't even talk to it in any way; I was hoping to find the IP address on the wired side of the AX.
Basically I'm trying to use the airport extreme completely backwards from the usual setup. Wireless to wired instead of wired to wireless.
Here's what I have:
Airport Extreme - Join a wireless network, security is WPA2, and it's on the network (as seen by 2wire)
Can I get the wired connections on the airport extreme to be an extension of the wireless network or even as another NAT routed connection?
DSL router (2wire) that sends wireless-> Airport Extreme (join a wireless network) -> wired connection to iMac.
Why am I doing this? No phone line connection even close to my iMac.

I had to jump straight into the manual configuration, but it does show Wireless mode: Join a wireless network. And the 2wire shows it as a device connected to that network.
Connect using: Wireless Network
Ok, I'm still a bit confused. On the AEBSn, the only options available for Connect Using (found on the Internet > Internet Connection tab) are: Ethernet or PPPoE; For Wireless Mode (found on the AirPort > Wireless tab) are: Create a wireless network, Participate in a WDS network, Extend a wireless network, or Off. Unlike the AirPort Express or Time Capsule, there should NOT be an option for "Join a wireless network."
So at this point I think it is extending my wireless network. I just can't figure out how to get the wired ethernet ports to be on that same network.
Regardless, when configuring for "Join a wireless network," the base station would join as a wireless client, not as a means to extend the wireless range of the exiting wireless network. Since this is not the way to set up a WDS, the Ethernet ports on the AEBSn would not be enabled for sharing Internet connectivity.
WDS is not an option as the 2wire router doesn't seem to be able to handle that.
Then it appears that there will not be an option to create a WDS no matter which vendor's router you try to configure the 2Wire to work with. Sorry!

Problems with AirPort Extreme and connecting to personal ftp

Hi all
I seem to be having a problem with connecting to my personal server outside of my network. When I connect using a static IP within my network(192.168.1.x) I can connect fine using my Mac and PC so I've ruled out improper server settings. I've mapped a port (21) to the same static IP as my server, but I cannot connect. I am prompted with "An FTP Connection to "xxx.xxx.xxx.xxx" could not be opened because the FTP server dropped the connection" I think I've toggled every option in the Airport Utility but nothing seems to work. Has anybody been successful in making this work?
Thanks for any help offered

OK, thanks for the info, which really helps.
Your AirPort Extreme is in Bridge Mode, so the IP addresses that your devices need are being assigned by the Cradelpoint router, not the AirPort Extreme.
Either the Cradlepoint router is not allowing more than 3 devices to connect, or it is your service provider that is limiting the number of devices that can connect....probably because of very limited bandwidth.
I'm not sure whether you want to try to contact support at Cradlepoint or your service provider to try to find out who is actually responsible for the maximum number of connections allowed, since they will likely each blame the other for the problem.
The workaround...if you want to try it, since it bends networking rules a bit....is to configure the AirPort Extreme as a router, not a bridge.
The upside to this is that all of your devices will be able to connect and get a valid IP address.
One downside is that this will introduce what is known as a Double NAT error on the network, but that is rarely serious on a home network, and Apple does provide you with the option to "ignore" the error, so you get a nice green light on the AirPorts.
Another downside may be....depending on the bandwidth that your service provides....that your connection is really slow....as in dial up speed slow....when you have a number of devices all connected to the network simultaneously, since they will all share the available bandwidth is provided.
I never had any problems in the past with wireless connections when I configured the AirPort as the router. But I also was very careful to avoid downloading large files using the Cradlepoint connection since the bandwidth was quite limited.
Not sure how you want to proceed.
We can tell you how to configure the AirPort as the router in this type of setup if you will let us know what operating system you used to configure the AirPorts, but we cannot guarantee that things will work for you if you try it.

Airport Extreme and connecting through ethernet port to Windows XP Pro SP3

I have today had the sad experience to loose network connection to My Windows XP Pro SP3 using the ethernet port on Airport Extreme Base station, the newest one.
It seems it won't pass an IP address for XP using DHCP, and to make things worse My wireless access using My is working okay!!!
Why do I only have this problem through ethernet ports on the Airport Extreme Base Station for XP, but wireless connectivity for My Mac's works????
If others have similar problems and have found a solution please let Me know.
Yes, I have twice today contacted My ISP provider but as the Mac's can connect the problem seems to lie with the Airport Extreme Base Station.
I will check this forum tomorrow and hopefully a response has been given to solve My problem
Kind regards
Engineer
Preben Duus
Denmark, Europe

You can access the AirPort Disk via normal file-sharing connection options, such as selecting the server from any Finder window’s sidebar in the Shared section. AirPort Disk uses two standard methods: AFP (for Macs) and Samba (for Windows or Linux).
Leopard accesses AirPort Disks through the Finder, just like any other network volume. Open any Finder window, and look in the sidebar for a list of servers in the Shared section. You should find your AEBSn.
To mount an AirPort Disk volume, follow these steps:
1. Select the AEBSn in the Sharing section of the sidebar.
2. To connect as a Guest user, you need take no more steps; To use a named account, click the Connect As button in the upper right and enter your credentials.
3. Double click a volume that’s shown to mount it on your system.
For both Windows XP and Vista, open the network browser by double-clicking Network on the Desktop. The base station name should appear in the Network browser.

Can time capsule connect to ethernet through airport extreme and then send wifi on a different band ?

Hope this makes sense.
At the moment, an Airport Extreme (n) is connected to a single wall outlet by ethernet and sends wifi signals at both 2,4 and 5 GHz.
I would like to add a Time Capsule (also n), position it immediately next to or above this Airport Extreme and connect to the AE with a very short ethernet cable (so not extending the Extreme's wifi signal since that could reduce the signal's strength by half).
This way both are connected to the internet by ethernet (the AE directly to the wall outlet, and the TC to the AE's ethernet out), hence both should be able to send wifi at full signal strength.
In order to achieve full wifi strength I would then set the Extreme to (only) send at 2,4 GHz and the Capsule to (only) send at 5 GHz.
Please note that the house has an open (loft style) floorplan, so there's no reason to position the AE and the TC at a distance from each other for wifi reach throughout the house.
Dear Bob, what do you think? I've been reading up but didn't find a directly related post.
Is this the right way to go about it?
KInd regards.

I would like to add a Time Capsule (also n), position it immediately next to or above this Airport Extreme
The position immediately above is poor.. and next to each other is even worse.. you are blocking the antennas from one side or the other..
Please use a patch lead of around 2M (6feet) min.. and place them that far apart.
very short ethernet cable (so not extending the Extreme's wifi signal since that could reduce the signal's strength by half).
Having the devices link wirelessly causes the speed to drop by half which is caused by double hop wireless.. it does not reduce signal actually.. but you can have interference issues.
In order to achieve full wifi strength I would then set the Extreme to (only) send at 2,4 GHz and the Capsule to (only) send at 5 GHz.
Please note that the house has an open (loft style) floorplan, so there's no reason to position the AE and the TC at a distance from each other for wifi reach throughout the house.
The gap between two radio transmitters is so they don't flood the receiver on the unit next to them.. It has nothing to do with the room. If I stick two transmitter/receivers next to each other they need some space. It is also to give full access to the antennas which are spaced around the sides on the older N models.
You also cannot turn off one band.. If they are dual band models.. ie Gen3 AE and later. Gen2 TC and later.. they are permanently dual band. You cannot do anything about it.
You can simply set the channels.. although auto should work.. there are 11 channels for 2.4ghz.. set one to channel 1 and the other to 11.
At 5ghz there are heaps of channels.. set one to 36 and the other to 149.. or whatever is available.
You are not going to achieve anything much doing this unless you have more clients than bandwidth.. ie both boxes can fully service internet to up to 10 clients.. maybe more if each band is used properly.. you will gain nothing using two routers next to each other.
Beaten by your preferred forum eggs spurt.. !!

Airport Extreme and Time Machine. Despite now being officially supported, does it work?

The subject says it all. After purchasing the new tall Airport Extreme and connecting a WD 2TB drive (as I had with the earlier AE) I have yet to have a backup execute properly. It will be fine for a few days then TM will announce it's done a verification and a new backup is required. Thank goodness I have offsite backup since TM is doing absolutely SFA for me at the moment.

Yuri van Hoof wrote:
Now I connected this USB External Disk to the Airport so I can use it as an network disk. This is working as well. I can get it mounted and read and write on it. Nice...so far.
Now I want TIme Machine to update/compleet my latest back-up, and here the problems start.
I hate to have to tell you this, but backing-up that way is unreliable and not supported by Apple. See: Using Time Machine with an Airport Extreme Air Disk.
But then I got the message; disk is full. Hmm?
Yes, because Time Machine stores backups differently when done over a network, it doesn't see the ones made while directly connected. See the blue box in #17 of Time Machine - Frequently Asked Questions.
Does anybody now how to get the old 'Backups.backupdb' connected ore recognized as the ONE which TM should compleet?
Realistically, you have two choices:
Knowing the considerable risks, as detailed in the first link, if still you want to back up wirelessly, connect the disk to your Mac and erase it. Then connect it to your Airport and let Time Machine start fresh.
To return to backing-up while directly-connected, delete the <Computer Name>.sparsebundle from the top level of the drive.

Airport extreme and original Time Capsule

I currently own an original Time Capsule. I am considering purchasing a new Airport Extreme and connecting the two together. I would like to be able to use all the Ethernet ports on both, but the wireless on the new extreme. What would be the best way to connect them with my cable modem?
Billy

You can elect to connect either the Time Capsule (TC) or the new AirPort Extreme Base Station (AEBSn) directly to the modem.
If you desire to get use of the maximum number of Ethernet ports on the AEBSn, then I would suggest connecting the TC to the modem. Also, note that you can always add an Ethernet switch or two to either router as well to expand the number of available Ethernet ports for wired clients.

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

How do you connect Airport Extreme and share HP Photosmart 3210 Printer?

Hello,
I have a Mac and PC Network composed of:
iMac 24'' Leopard 10.5.2 (main computer)
2 PC Fujitsu Pentium 4 on Windows XP
2 PC HP Pentium 4 on Windows XP
my network/connections are done via Airport Extreme and 2 hubs (other devices connected to the network like Wii, XBox etc.)
I am trying to share my HP Photosmart 3210 using the USB connector on Airport Extreme but I am experiencing strange problems while printing from the iMac. I can print an e-mail or a "light" document however if I want to print a Mac powerpoint (Mac office) largest document, the problem starts after the second or 3rd page, the printer goes on pause at the middle of the page and the interface indicates "problem communicating with the printer" or something like that.....unique possibility is to turn the printer off and start again but the problem persists. However, it seems that the printer works ok from the PC's.
I have tried to install the latest versin of the HP driver on my iMac but while configuring, the printer doesn't appear....I have checked on the printer settings and the IP address is 0.0.0.0.
I am now thinking about connecting the Printer via one of the Ethernet port on Airport Extreme.
Questions:
1. Any help on the above ? Any advice ?
2. Is it normal to have no IP address on the printer when connected via USB on Airport Extreme ?
3. Why HP config doesn't recognize the printer on the network ?
4. Why does it work from the PCs and not from the iMac and why does it print light documents and not big ones ? Is this a memory7buffer problem on the printer ? What can I do if this is the case ?
5. On the Airport Extreme Utility, do I need to share the printer via "Bonjour"?
6. I am willing to plug an extrenal HD on the Airport Express USB port. Is it possible to put first a multi USB port on the Airport Extreme USB or is it going to cause problems ?
Thanks a lot for your help.
P.
Message was edited by: vador300
Message was edited by: vador300
Message was edited by: vador300
Message was edited by: vador300

NCBob, Welcome to the discussion area!
If I understand correctly you are replacing the Linksys. It should be a simple replacement. Connect the cable modem to the WAN port on the AirPort Extreme base station (AEBS). Connect your Ethernet devices (including the switch) to the AEBS LAN ports.

Can I connect a 4 TB USB drive to the airport extreme and use it as a network drive for Time Machine

Can I connect a 4 TB USB drive to the airport extreme and use it as a network drive for Time Machine

Yes, if the drive is formatted in Mac OS Extended (Journaled).
The USB port on the Time Capsule is under powered, so you may need use a powered USB hub with the 4 TB drive...even if it has its own power supply.

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

Extending using a wireless connection always results in a performance compromise.
If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
Post back to let us know which way to you want to go.

I have my Time Machine on an external drive (not connected to Airport Extreme) and I have an external HD attached to airport extreme. Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme. How?

I have my Time Machine on an external drive (not connected to Airport Extreme) and I have an external HD attached to airport extreme. Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme. How?

Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme.
Sorry, but no.
Time Machine will backup your Mac, but not the hard drive attached to the AirPort Extreme.
Time Machine will back up a hard drive only if it is attached directly to your Mac via USB or FireWire.

I already have a hard drive connected to my airport extreme, and ws wondering if i could use it as a network storage device

I already have a hard drive connected to my airport extreme, and ws wondering if i could use it as a network storage device. If so would I have to format it with two partitions , one for time machine and the other for network storage. Aprreciate any advice

If you have the hard drive connected to the AirPort Extreme....it is a network storage device.
One issue that you may want to think about is that Apple does not support Time Machine backups to a hard drive at the USB port at the AirPort Extreme.
In spite of this, some users who try this are able to make it work. Others have some limited success and some have no success.
It's not supported....so there will be no help from Apple in the event of problems.
If you decide to proceed with this, make sure that the partition for Time Machine backups is formatted in Mac OS Extended (Journaled) as other formats will not work with Time Machine.
Having a secondary backup plan would also be something that you might want to consider.

Can I connect an external hard drive to one of the ethernet port of the airport extreme and access it from my Mac or PC?

Can I connect an external hard drive to one of the ethernet port of the airport extreme and access it from my Mac or PC?

If this hard drive is part of a NAS device, then yes it should be accessable from either a Mac or PC while connected to the AirPort Extreme Base Station (AEBS) by Ethernet.

Airport extreme and connection to imac

Similar Messages

Maybe you are looking for