AirPort Extreme and Fixed IP Address

Hi,
We've recently moved into a new apartment with pre wired internet - we basically connect via a Cat 5 port in the wall. Our ISP has provided us with fixed IP address, subnet mask, DNS information etc and this works fine when we directly connect via a cat 5 cable to the port, but as soon as we hook up the airport to the port in the wall and try to go wireless - we get no internet. We've used the airport set up facility and entered all of the data that we have, but we get nothing. The only information that we are not sure of is the router address - is this the address that the airport uses or is it a value that we need to get from our ISP? Thanks in advance

Try setting the Router Address as the IP address you are given except change the last number to a 1. For example, if the fixed IP address you are given is 74.63.128.33, try using the router address as 74.63.128.1 (this is how all my router addresses are given when using DHCP). If that doesn't work, call your ISP and ask what the router address.
As a note though, once you setup your AirPort for your static IP address you want to change the settings on your computer to use DHCP instead of that static IP address. The reason being is that the AirPort now is assigned that address and it is the AirPort's responsibility to assign private IP address to all computers on the network (basically all your computers on your AirPort are sharing that one IP address). That's not to say you can't use static IP addresses but if you are using the generic Apple setup your IP addresses would be something like 10.0.1.100. Unless you need to enable port forwarding I'd suggest just letting the AirPort act as your private DHCP server, and in order to do that you must make sure your computes are set to Configure IPv4 using DHCP instead of manually.

Similar Messages

IMac on Netgear X104 and Airport Extreme intermittently loses IP address

We have a Netgear X104 plugged into an Airport Extreme Base Station.
Another X104 (which carries network information through the household electrical wiring) is plugged in for a networked iMac with OS X v 10.5.4.
The network works flawlessly, but every few days, the iMac loses its IP address. All lights are working properly on the X104, indicating that it is seeing the network.
The only workaround on the iMac is to go to: System Preferences/Network/Advanced and click RENEW DHCP LEASE. The iMac then gets reassigned a new IP, such as 10.0.0.200 by the Airport Extreme.
The Airport Extreme, settings are as follows.
Wireless Mode: Create a wireless network
Wireless security: WPA/WPA2 Personal
Connect using: Ethernet
Configure IPv4: Using DHCP
IP Address: Provided automatically
Powering off and on the Airport Extreme and the Cable Modem have not fixed this recurrent problem.

Hi,
http://osxdaily.com/2009/12/22/mac-wireless-problems-guide-to-troubleshooting-ai rport-wireless-problems-on-your-mac/
Hope it helps.
Cheers.

Verizon Fios - Airport Extreme AND Airport Express drop IP Address

Hi everyone,
I am absolutely BEGGING for help here! I am so frustrated with Verizon Fios that I can hardly take it. The scenario - the crummy Actiontec router that Verizon provided us when we got service 10 months ago shot craps recently. So, I got out my Airport Extreme to see if that would work. After 30 minutes of tech support I got it working, only to have all kinds of trouble with what they told me after FURTHER hours of tech support, was that my router was dropping the IP address.
So, knowing that I can't possibly be the only Verizon customer using an Apple router, I thought it was the Airport Extreme unit itself. I went out and got an Airport Express, and again, I am resetting my router or calling Verizon tech support at least once a day, if not more, to break the lease and get a new IP address. It's killing me. I can't live life like this.
Can ANYONE help me figure out how to get this scenario to work without having to purchase another crappy, ugly Actiontec router? I don't have FIOS TV, just internet. I can't tell you how much I would appreciate the help. It's driving me insane!!
Thanks so much in advance.

It appears that I am in same boat. I got FIOS last October and it worked seamlessly with my Airport Extreme/Express network for months. All of a sudden, we couldn't get to the internet after returning from vacation in late August. Reset, reconfigured, and tinkered with the Airport extreme and our computers, but could not get out to internet even though we could still print and see each other over the airport network. Contacted Verizon and they told me that they do not support the airport and that we have to use their Actiontec router for Internet access. Told them that we had been using our Airport, connected to their Actiontec, to access the Internet for months seamlessly and they said that that was not something they would recommend/support and that we had to go directly through their wireless router to get Internet support. I asked if they changed something in the last week that would prevent access and they would not confirm.
We also found that my son's older desktop with 802.11b wireless USB connection and MS OS can't even get out using the Actiontec router directly. Verizon site talks to 802.11b not necessarily being supported, but we had no issues when we were routing everything through the Airport. I just don't want to invest in all kinds of new network devices when we were fine until something happened over a weekend.
I am playing around with buying the latest Airport extreme (ours is a 802.11g model) to see if that works, but Verizon refuses to acknowledge that it's a viable solution and apologized to us that we have to switch between their network router and our Airport router to do routine printing, play music, etc., but they were not open to helping us prevent running multiple networks, either.
Obviously, this is unacceptable customer service, but Verizon techs that I spoke to do not feel that they have any obligation to support us with re-establishment of connectivity that we got with our original service. It sounds from this thread that other folks were getting disconnected or can't establish connectivity over the summer. Am wondering what Verizon is doing that is causing this and who else is getting impacted. Also wondering if upgrading to the latest Airport will help.

Airport Extreme and Canon Pixma MP610

I recently got a MacBook Pro. I wanted to print wirelessly so I also purchased a new Airport Extreme and Canon Pixma MP610 printer all from the Apple Store. I told the salesperson what I wanted to do and he did not indicate there would be a problem, he said make sure I had the most current printer drivers, which I have done. I tried everything but I am unable to print wirelessly using the USB connection between the Airport and the printer. Can anyone help me? Is this printer compatible with the Airport? This is very frustrating and expensive. I could have just kept my old base station and printer.

I am having the same problem with my MP610... I have connected the printer to the usb port on the AirPort Express and have tried installing various drivers to try and fix the issue but have had no success so far.
My Airport Express is setup correctly (green light) and is found in AirPort Utility... additionally, when I go to System Preferences -> Print & Fax, the printer is there and found wirelessly... yet whenever I try to print I receive a "error number : 306..." in my print queue... also, depending on which driver I use, I receive a "Unable to send 1 bytes of print data! (USB write error)" error message on top of the "error number : 306"... sometimes I also manage to avoid any error messages where the status shows it is 'Printing' but there is nothing being printed...
Now, obviously this is a wireless issue, as the printer works when connected via usb directly to my MacBook Pro...
I contacted Canon Support, and was told that I would not be able to print via any AirPort connection as the printer itself is a "Host Based Printer" and was not designed to support networking and that my only other alternative/option to wireless printing would be to purchase a "USB printer server" that supports IP Address forwarding... (on a side note: does the AirPort Express not support this?)
The whole reason why I purchased AirPort Express was so I could print wirelessly from a regular printer by connecting it to its usb port... and looking at the Airport support page on Apple's website, it clearly doesn't mention anywhere that the printer needs to be network capable or that there would be any compatibility issues with regular printers... After-all, it revolves around the idea that all you need to do is connect the printer to the AirPort via USB and that it will take care of the rest when setup correctly...
So ultimately my question is, has anyone had any success in setting up a wireless connection with their 'Host Based Printer'/ordinary usb printer...? if so, how?!! please describe in detail :P lol
Also is that doesn't work, is there any way I can use the AirPort Express to wirelessly print using an IP Address without having to buy a 'USB print server'?
Sorry about the very long description... any help would be really appreciated!

Airport Extreme and external HDD - cannot be found under Windows (XP/Vista)

Dear All,
I am about to loose it. I have an Airport Extreme (7.4.2), most recent version (802.11n)connected to my cable modem. Attached is a 2TB HFS+ Formated HDD. I have a number of machines. My primary machine is a Dell XPS with Vista and MacDrive installed.
Now: On my AirPort utilities through the Dell the different HDD's connected via USB (I have tried half a dozen) are all visible. They are shared and I have tried all options, e.g. "with Disk Password" etc, tried to give and deny access to guests etc.
I have tried various things incl. switching off the firewall has not been a success either. I am basically ready to buy a Mac now, but I am worried that the problem will persist for all my Windows based PC's.
Who can help with a step to step guide? tried the TCP/IP settings on the XP machine as well (entering the IP address of both Airport Extreme and Express).

Hi!
I've got the same problem as of Friday when I upgraded my Notebook from XP to Windows 7.
It does not recognize the HDD anymore, neither on the Windows7 Notebook nor on 2 different XP- PC's.
I disabled the password functionality and removed the HDD several times, no change.
When I look to the data volumes overview in the system settings, all internal HDD's and the CD partition of the Toshiba drive are shown. The HDD partition of the drive is shown as "non allocated".
Is there any workaround to get access to the data????
Best regards,
Helmut

New Airport Extreme and iPhone Issues

I've had the networking day from ****. I previously had a 3rd Gen Time Capsule at our restaurant, connected to a Cisco 26port gigabit POE switch and Comcast digital voice and internet. Over the past few days, employees have reported trouble accessing the the Wifi network. After several restarts and firmware upgrades (including the dreaded "firmware problem" to fine update), nothing worked. I changed channels, back to auto, back to specific channels, back to auto. Made open guest networks. Nothing worked consistently. My iPhone might connect and my friend's might not. Nor his laptop consistently. Our Axis network cameras might take a bit extra time to connect. All quite random and quite frustrating.
So I swap out an older Airport Extreme (4th gen I believe) using the same configuration as the TC (Time Capsule). It works fine, except for the last port not working as expected. No matter, I plug the mac mini into the Cisco switch and off we go. Nevertheless, I'm still told we are suffering random Wifi issues. So I buy a brand new AE (5th gen) today to replace that one. Should work like a charm I thought. Right....
Several hours later, I finally have the new AE working, but only after doing several hard resets/factory restores, the works. For some reason, the mac mini could not successfully update any of the connected AEs - whether connected directly into the same AE, or if the Mini was connected to the switch. Nothing worked. Every time I tried to update the AE, it would hang and force me to unplug and plug it back in. It would also never save setting changes. I finally resorted to a friend's macbook to be able to restore it successfully. And once that worked, the mini was able to update the AE flawlessly. Our Point of Sales (POS) machines connect fine, our cameras connect fine, wifi printer connects, and the mini connects, and everything has internet.
Except my iPhone 5. Of course. It gets a signal fine (full bars). It gets an IP address. But I can't surf the web. Or download email. Or iMessages. Anything. No internet access. I try hard restarts on my iphone. I try assigning IP addresses by MAC address. I try resetting the AE. I try renaming the WiFi name. Nothing. I can make a guest network that works (on a different IP table, btw - 172, not 192.) But other than that, no access. Grrrr.
So I have a "working" AE router where some devices successfully connect (through wifi and ethernet) and some dont' (wifi iPhone). My iPhone connects fine to my home TC. So shouldn't be anything to do with that. But I'm at a loss. I'm going to go back and restore everything and power cycle everything tonight or tomorrow night. I don't know if that will help, but it's worth a try. Lord knows it feels like I've tried everything else.
Anyone have any good ideas of where to start besides voodoo dolls and baseball bats?

I took mine back, because I was having these very same issues. We use contivity too. I was able to connect only to one of three of the servers we manage (in Europe). I couldn't connect to the servers in Asia or here in the USA.
Replaced the Airport Extreme with my trusty old d-link 624, and no issues connecting to any of the three hubs.
Otherwise, I liked the Airport Extreme, and I'll consider buying it again when and if they address this VPN issue. I work at home so its obviously a "deal breaker" for me.

How to setup a network with a time capsule, airport extreme and an airport express?

Hello.
First I want to make it clear all my knowledge off wireless networks is going on forums on the internet, before a couple of months ago I didn't realize wireless networking was so intricate so forgive my lack of experience.
I just bought a time capsule (today, 4th generation), I have an airport extreme bought in January 2011 (they just got refreshed so mine is now one generation old) and the same with my airport express (bought in January).
I originally bought the airport extreme and setup a wireless network using the dual band setup. I have no issues with the 5ghz network and most of my devices run on wireless n so I had no issues with them. my only two wireless devices that can not use the 5ghz network is my iPhone 4's which use wireless n but it has to use the 2.4ghz signal. Problem is in my apartment I am bombarded with other peoples 2.4ghz networks so my signal is terrible 10-15 feet from the airport extreme. Near my extreme I am getting signal ranges around 15mb to 20 mb. When Im about 15 minutes away in my bedroom (so one wall in between) my signal plummets to 1-2 mb. sometimes as low as 0.17mb which is not good. I got the airport express to extend my range and placed it in my bedroom. . After setting up the airport express the signal still was terrible. I researched and realized that if the signal strength ***** then the airport express cant boost the signal as much which makes sense in hind sight. I then researched setting up a roaming network or a WDS network. Per research a WDS network was not recommended b/c I was not using a wireless g network. I attempted to create a roaming network and then realized that you can not use an airport express in a roaming network. This has led me to now buy a time capsule.
First, in my setup do I or should I have the time capsule as the primary? I believe its more powerful than the airport extreme but Im not sure if that matters in a network that is distributing wifi from ethernet (thats how I am connected the extreme and the time capsule)
so can I do
cable modem ETHERNET Airport extreme(in the living room where its always been and works great in that immediate area) (3rd generation) ETHERNET Time Capsule(in the bedroom where I usually get poor signal) (4th gen) and then an airport express connecting to the 2.4ghz signal in the bedroom where the time capsule also is EXTENDING the wireless range?
or should it be the time capsule first bc its more powerful?
I tried setting up this setup and everything is green but I don't know if what I am doing is actually working on full cylinders b/c I am confused on some aspects. mainly on the airport extreme which is the primary device I have under the wireless tab selected create a wireless network and on the time capsule it also is on create a wireless network with the network name being exactly the same. Should it be changed to extend a wireless network? and then bridge mode? Should I have different channels for the different devices that are on 2.4ghz?
I am open to hear ANY suggestions, or ideas to improve my setup. PLEASE PLEASE HELP!!!!!!!, lol its been 5 long months of poor internet in my bedroom where my wife has her setup with a roku box and wifi tv (I have those hardwired for now) but mainly for her iPad and iPhone b/c its so bad sometimes she has to turn wifi off and use 3G. I have same issue in my bathroom, sometimes Im getting decent signal and sometimes its so bad I can't open the link on an RSS feed in safari which I have to assume doesn't require that much bandwith?
I have no wireless g devices. The only device I need 2.4ghz for is my iPhone 4's but they both use n also. All my other deivices connect on 5ghz and my 5ghz network is decent, a lot better than the 2.4ghz network atleast.

You wrote so much that I find it hard to address all your concerns. However, here are some thoughts:
1) I'd configure the Time Capsule as the "main" router, connected directly to your cable modem. Configure it to "create a wireless network" and to "Allow this network to be extended". Configure the other devices to "Extend a wireless network".
2) Put any device that's extending the network half way between the main router and the wireless clients. If the signal from the main router is weak at the cllient's location, then the extending device will also receive a weak signal.

I have a airport time capsule, an older airport extreme, and an airport express. I want to hard wire my Mac Mini to the network. What is the best arrangement of the devices? which ones should be hard wired to optimize extending the network?

I have a airport time capsule, an older airport extreme, and an older airport express. I want to hard wire my Mac Mini to the network. What is the best arrangement of the devices? which ones should be hard wired to optimize extending the network?

I am using TM Unifi with an ASUS RT-N18U Wi-Fi router. I would like to know could I use Apple AirPort Time Capsule to extend (repeater, booster) my Wi-Fi to a part of the house where the Wi-Fi signal is poor
Yes,, if you plan to connect the AirPort Time Capsule to the ASUS router using an Ethernet cable connection that will remain fixed and permanently installed at all times.
No, if you were planning to have the AirPort Time Capsule connect wirelessly and extend the Asus WiFi signal, since it would not be compatible with another manufacturer's router for that purpose.
Another way of saying the same thing here would be that if you want to extend the network wirelessly, it will take two Apple routers to do so

802.11n AirPort Extreme and Express

Hello,
Thank you in advance for all your help and replies, I truly appreciate it.
I'm looking to purchase an 802.11n Airport Extreme and AirPort Express. I want to setup the Extreme next to my DSL modem and setup the Express in another room and have it extend the wireless network. The Express will also serve as an ethernet port from my DVR unit. I have read different posts that indicated that if I setup the Express to wirelessly connect to the Extreme, via WDS, or some other method, the wireless network will be downgraded to 802.11g. I currently have a 802.11g wireless network. I have one Buffalo Technology 802.11g wireless router and one Buffalo Technology 802.11g router (setup as an access point) and can do everything I need except connect a external HD via USB.
If at all possible, I would like the entire network (Extreme and Express) to use the same SSID and password. Have the Extreme perform the MAC filtering, provide DHCP address, and service a guest network.
So, do I understand what I have read correctly, that connecting an 802.11n Extreme and 802.11n Express via wireless (WDS, or other method) will downgrade the network to 802.11g? Are there any other recommendations on how I should connect these two devices and provide 802.11n service?
Again, thank you in advance.
--GMReed

When using the "extend" feature with the new 802.11n base stations, the extended wireless network operates in the 802.11n mode. I believe you may be referring to one of two things that may have led you to that conclusion: 1) When extending a network with the older static version of a WDS, the extended network operates in the 802.11g mode. This is true when either or both base stations are 802.11g models, and 2) Non-"n" wireless clients, connected to a "n" network, will bring the network down to the lowest bandwidth level of the oldest standard. Although connecting these types of clients does affect the overall bandwidth available to "n" clients, it does NOT bring the overall wireless network down to "g" or "b" level.
>If at all possible, I would like the entire network (Extreme and Express) to use the same SSID and password.
By default, both base stations must uses the same Network Name or SSID and wireless password to work properly.
>Have the Extreme perform the MAC filtering, provide DHCP address, and service a guest network.
For MAC filtering in an extended network, both base stations must be configured with the same MAC addresses for all clients that you want access to the extended network. The Extreme would provide DHCP service, but (unfortunately) you cannot extend the guest network.

Airport extreme and express & apple TV

I have an airport extreme and express & apple TV. I'd like to do the following:
1) Extend the network via the express
2) Enable the express to stream music to the stereo from the apple TV
I am sure someone has figured this out but I can't find the answer...
Thank you

Firstly, the easiest bit (although I don't believe you need to do this):
I would try "downgrading" the Extreme station's network type to only b/g (excluding n entirely), but I don't see that option in the radio settings anymore
You will get additional settings if you hold down the option key while browsing the radio settings drop down menu.
Moving on: Unfortunately a dropped connections seems to be a problem with umpteen causes and not only is it difficult to troubleshoot with someone in a forum it can also be made even more difficult because many problems are associated with network settings on a router that the person who is trying to help is unfamiliar with.
However you seem to be convinced your problems arise when your express is running which may narrow things down a little if correct, if not it may actually lead us away from the answer to your issue.
Is it the kind of security I'm running? Should I try WEP or... none at all?
I use WPA and have no problems (password = 8 Characters)
Should I attach it a different way? Perhaps manually set it to "participate in a WDS network" or "extend a wireless network?
I have my expresses set to participate in a WDS network, but that's because I use them for other things other than itunes, I would have thought 'join a network' would be fine.
You could check that all your devices are using independent IP addresses and all are using the same subnet. You could also check that no two devices have the same mac address, I've been told a million times this can't happen, but I've seen it. You may be wise to check these things before and after your devices have been 'kicked off the network", you may even want to write them down to see if any are changing.

Airport Extreme and Airport Express on Ethernet Wired Network

I recently did work on my house and now have the house hard-wired for ethernet. I have an AirPort Extreme in my home office. That signal does not reach past the old part of the house (brick apparently blocks some of the signal). So I want to use my Airport Express in the new part of the house to have wireless in the new part as well.
Currently, I have the Airport Extreme plugged into the network, with the Airport Express plugged into the network in the new room. I get wireless connection in the office, but not in the new room.
I am not sure how to configure the base stations.
-- Do I need to use WDS? I am not currently, because each wireless router has its own independent wired link to the network.
-- Do I need to call the wireless networks by different names? Currently I have them both called the same thing.
-- Do I need to set the Airports for a different channel? Currently I have one on 10 and one on 11.
This should be very simple. Unfortunately, my experience has been that the Express base station is very difficult to configure, very quirky and not for the average user.
BTW, the Express is hooked up to the stereo and iTunes plays through that-- but remember it is a hard wired connection. Also both Airports show up in the Admin Utility, so no problem there.
Thanks.
~aviduser
1. Macintosh SE (1988)
2. PowerBook 180 (1993)
3. PowerMacintosh 7600 (1996)
4. PowerMacintosh G4 (2001)
5. PowerBook G4 12" (2003)
(Oh yeah, and there was the Newton MP2k)
G4 867 Quicksilver Mac OS X (10.3.9)

Do you have another router?
If not:
Connecting them together via Ethernet should be done like this:
Internet -> [WAN] AEBS [LAN] --> AirPort Express
The AirPort Express should so that the option to distribute IP addresses is disabled. The AEBS and Express should have the same network name and encryption configuration. The AEBS and Express should be on different channels.
This configuration will put all the computers on the same subnet. All of the computers will get IP addresses from the AirPort Extreme base station (AEBS).
OR connecting them via wireless should be done through WDS. The hardware connection should be done like this:
Internet -> [WAN] AEBS
The AirPort Express should not be connected to Ethernet.
See KB 107454, AirPort Extreme and Express: Using WDS to create a network from multiple base stations.
If you do have a router, then both AEBS and Express should be configured so that the option to distribute IP addresses is disabled. The hardware connections should be set up like this:
Internet -> router -+-> [WAN] AEBS [LAN]
....................|-> AirPort Express
The AEBS and Express should have the same network name and encryption configuration. The AEBS and Express should be on different channels.
This configuration will put all the computers on the same subnet. All of the computers will get IP addresses from the router.

Setup a wired network between Time Capsule, Airport Extreme and Express

I currently have a Time Capsule, Airport Extreme N and an Airport Express N. They are currently connected wirelessly via the "extend network" mode. So I do have wireless connection throughout my home but I notice that it is slow especially compared to gigabit Ethernet. I now like to do the same but then connect the three devices over Ethernet as I have on each floor also Ethernet connections available that are connected via a wired switch.
How can I configure the three devices in such a way that they use the gigabit Ethernet wired connections as their "backbone" and then give wireless access to each floor as if it is one wireless network, and where I can connect other wired gigabit devices via the time capsule and airport extreme Ethernet ports?
I have one Internet connection that comes via Ethernet from my cable modem. This is now connected to my time capsule who creates the internal network and assigns internal IP addresses.
Can anybody advise how to configure each device? And to which ethernet port I should Airport Extreme?
Thanks
Alexander

Welcome to the discussion area, Alexander!
+How can I configure the three devices in such a way that they use the gigabit Ethernet wired connections as their "backbone" and then give wireless access to each floor as if it is one wireless network, and where I can connect other wired gigabit devices via the time capsule and airport extreme Ethernet ports?+
You will be setting up what is known as a "roaming" network using the etherent backbone for your network. This will produce the best possible bandwidth on your network for both ethernet and wireless connections.
_On the Time Capsule_
Open AirPort Utility - Click Manual Setup
Click the Wireless tab below the row of icons
Remove the check mark next to "Allow this network to be extended" (This is only checked if you are extending your network using wireless only and you will be using ethernet to connect your devices, not wireless).
Update to save changes and the Time Capsule configuration is complete.
_On the AirPort Extreme_
Connect an ethernet cable from one of the LAN <-> ports on the Time Capsule to your ethernet switch. Then connect another ethernet connection from the switch to the WAN (circle icon) port on the AirPort Extreme.
Open AirPort Utility - Click Manual Setup
Click the Wireless tab below the row of icons
Wireless Mode = Create a wireless network (Not extend as you might think. Extend is only used if the Time Capsule and AirPort Express are connecting using wireless only)
Wireless Network Name = Exact same name as your AirPort Extreme wireless network
Radio Mode = Same setting as your AirPort Extreme
Channel = Automatic
Wireless Security = Exact same setting as your AirPort Extreme wireless network
Wireless Password = Same password as your AirPort Extreme wireless
Confirm Password
Click the Internet icon
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Update to save changes and configuration is complete
_On the AirPort Express_
You can connect an ethernet cable from the switch..or..from one of the LAN <-> ports on either the Time Capsule or AirPort Extreme, whichever is easier.
Set it up exactly the same as the AirPort Extreme above and update to save changes.
Power off the Time Capsule, AirPort Extreme and AirPort Express for a few moments. Then power up the Time Capsule first and let it run a moment, then power up the AirPort Extreme and then the AirPort Express.
If you have a laptop running Leopard or Snow Leopard, you can move your computer around and check to see which device it is connecting to for wireless. Hold down the option key while you click on the fan shaped AirPort icon at the top of the screen and look for the BSSID. That is the AirPort ID of the device to which you are connected at the time.
To get the AirPort ID of each of your Apple routers, open AirPort Utility and click on a device on the left. On the right, you'll see the AirPort ID for that device.
For ethernet connections, you can plug into an available port on the switch, the Time Capsule, or the AirPort Extreme.
You should be all set. Please post back on your progress.

I have airport extreme and just purchased a D-Link DCS-932L home network camera. D-Link says I need UpNp but the extreme doesn't support this. Can I use port mapping? if so anyone know how to set that up? thanks

I have airport extreme and just purchased a D-Link DCS-932L home network camera. D-Link says I need UpNp but the extreme doesn't support this. Can I use port mapping? if so anyone know how to set that up? thanks

Since the D-Link DCS-932L is accessible on the local network via a web browser, you should be able to access this camera from the Internet if your router has a publically accessible Public IP address. If your ISP provides you with a dynamic Public IP address, you may want to use a DDNS service to make it easier for you to locate your camera whenever your ISP changes your IP address.
Start the AirPort Utility > Select the 802.11n AirPort Extreme Base Station (AEBSn).
Select Manual Setup.
Verify that Connection Sharing = Share a public IP address is selected on the Internet > Internet Connection tab.
Select Advanced, and then, select the Port Mapping tab.
Click the plus sign to add a new port mapping.
For Service, leave the default; this will change to "Custom" once you start entering port values.
In the Public UDP Port(s) and Public TCP Port(s) boxes, type in a 4-digit port number (e.g., 8888) that you choose. In the Private IP Address box, type the internal IP address of your camera. In the Private UDP Port(s) and Private TCP Port(s) boxes, enter the appropriate port values that should have been provided to you by the camera manufacturer. Click Continue.
In the Description box, type a descriptive name like "Internet Camera Access," and then, click Done.
Click on Update.
To connect to the shared Camera from a remote location using a Mac or PC:
Start your favorite web browser.
Enter either your Public IP address or DDNS-provided Domain Name, followed by a colon and the Public port number that you choose in step 7 of the previous procedure. For example: http://123.123.123.123:8888 or http://www.mydtdnsdomainname.com:8888

How do you connect Airport Extreme and share HP Photosmart 3210 Printer?

Hello,
I have a Mac and PC Network composed of:
iMac 24'' Leopard 10.5.2 (main computer)
2 PC Fujitsu Pentium 4 on Windows XP
2 PC HP Pentium 4 on Windows XP
my network/connections are done via Airport Extreme and 2 hubs (other devices connected to the network like Wii, XBox etc.)
I am trying to share my HP Photosmart 3210 using the USB connector on Airport Extreme but I am experiencing strange problems while printing from the iMac. I can print an e-mail or a "light" document however if I want to print a Mac powerpoint (Mac office) largest document, the problem starts after the second or 3rd page, the printer goes on pause at the middle of the page and the interface indicates "problem communicating with the printer" or something like that.....unique possibility is to turn the printer off and start again but the problem persists. However, it seems that the printer works ok from the PC's.
I have tried to install the latest versin of the HP driver on my iMac but while configuring, the printer doesn't appear....I have checked on the printer settings and the IP address is 0.0.0.0.
I am now thinking about connecting the Printer via one of the Ethernet port on Airport Extreme.
Questions:
1. Any help on the above ? Any advice ?
2. Is it normal to have no IP address on the printer when connected via USB on Airport Extreme ?
3. Why HP config doesn't recognize the printer on the network ?
4. Why does it work from the PCs and not from the iMac and why does it print light documents and not big ones ? Is this a memory7buffer problem on the printer ? What can I do if this is the case ?
5. On the Airport Extreme Utility, do I need to share the printer via "Bonjour"?
6. I am willing to plug an extrenal HD on the Airport Express USB port. Is it possible to put first a multi USB port on the Airport Extreme USB or is it going to cause problems ?
Thanks a lot for your help.
P.
Message was edited by: vador300
Message was edited by: vador300
Message was edited by: vador300
Message was edited by: vador300

NCBob, Welcome to the discussion area!
If I understand correctly you are replacing the Linksys. It should be a simple replacement. Connect the cable modem to the WAN port on the AirPort Extreme base station (AEBS). Connect your Ethernet devices (including the switch) to the AEBS LAN ports.

AirPort Extreme and Time Warner RoadRunner Service Issue

I have Time Warner's RoadRunner Turbo Internet service, which promises a minimum bitrate of 15 Mbps for downloads and 1 Mbps for uploads. Recently, my measured throughput has crashed on uploads, to well below 100 Kbps (0.01 Mbps) while going through my AirPort Extreme over 100/1000Base-T cable (system 7.4.2). When I directly connect my Mac to the cable modem, I get a consistent 28 Mbps down and 1.7 Mbps up and a ping time of 20 ms. I've tried cycling power, soft resetting, and even hard resetting to factory settings, but nothing seems to fix this throughput issue. I'm going to try a cheap 3rd party router (D-Link or Linksys) to see if I can get my throughput back up, but is there something I'm missing on my setup? I have opened SSH, IMAP and Apple Remote Desktop through the AirPort Extreme, and have enabled Bonjour on it. I can't figure out why this change has happened so suddenly.

power down the network and the modem. connect modem to the extreme wan port. connect pc to ethernet lan port. power modem up first then the router. use Airport Utility to configure your network.

AirPort Extreme and Fixed IP Address

Similar Messages

Maybe you are looking for