Airport Extreme, Apple TV and two Expresses

I have a network that runs between the Apple Extreme and the Apple TV. I joined two Expresses to that same network. The Apple TV disconnects now when I play music through the two Expresses.
Should I set up two different networks: Extreme to Apple TV (one network)AND Wireless G Adapter to the two Expresses (a second network)?
Thanks for your help,
Matt

This may work if your assumption (and mine) is that your existing wireless LAN doesn't have enough bandwidth to support an AppleTV and two Airport Expresses.
I assume you are thinking of having one cabled LAN with two wireless access points on it - one dedicated to communicating with AppleTV (using an Airport Extreme N base station) at N-only speeds, and another dedicated to communicating with the two Expresses (could use any wireless router or access point that supports b/g speeds). Yes - that will work and may well solve your problem.

Similar Messages

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

Network question / using extreme apple tv and airprt express

I have a wired airport extreme in my office on a pc( i also use it to run 2 mac books wireless) and apple tv in living room.
my question is!!!!
can i put an airport express in my loft and use the ethernet plug wire to connect a pc (it doesnt have wireless) and if so how?

Yes, you can use an express to create a network for presentations, your main concern would be configuring it, which you would need to connect it to a computer to do.

Airport Extreme, Apple TV and USB Drive Speed?

I've just purchased a new airport extreme and 1.5 TB external hard disk. I figured out how to mount the disk and share it over my home network. I also designated a folder on the disk as my iTunes music folder (I purchased the airport and HD for the express purpose of achieving this set up, because I've accumulated so much media through iTunes that my MacBook Pro's internal disk has long since been full and I've been storing TV shows, movies, etc. on an external drive). The set up works -- BUT it is SLOW, especially when my Apple TV is syncing with iTunes.
Is there an optimal way to set up these connections so that syncing is not so slow?
Any help would be much appreciated!

HI and Welcome to Apple Discussions ...
*"internal disk has long since been full"*
Right or control click the MacintoshHD icon on your Desktop, then click: Get Info. In the Get Info window, click the discovery triangle so it's facing down. You will see; Capacity and Available Make sure you have 10% available disk space, 15% is better. Insufficient available space, can cause performance issues, system corruption, and possible loss of data.
Carolyn

I am using an Airport Extreme for wireless and a Netgear VPN Switch for wired connections. How do I get the two networks to connect?

I am using an Airport Extreme for wireless and also have a Netgear VPN Switch (FV5318) for internal wired ethernet connections. How do I get the two networks to connect to each other?

Tesserax, I would like to keep the Airport Extreme in nplace before the Netgear FVS318 switch because I am using all of the 8 ethernet outputs distributed to 8 differerent locationsl This way I can just use one of the LAN outputs from the Airport to feed the FVS318. Here is what I think I am hearing you say:
Tne reason why the wired and wireless devices are not communicating is because the FVS318G is also a DHCP server and in conflict with the AEBS.
To remedy the situastion here is probably what I need to do in order:
1. Change the LAN IP Address of the Netgear FVS318G to be the same subnet of the Airport Extreme.
2. Then, disable the Netgear FVS318G as a DHCP server.
3. Make sure the ethernet cable from the LAN port of the Airport Extreme connectis to the LAN port of the Netgear FVS318G.
4. Restart everything.
Can you provide me the steps I need to take to get the right IP addresses from the Airport Extreme to put into the Netgear to fix the conflict? I have the Airport Utility. I also have two airport express hot spots, and two Apple TVs in addition to computers attached to the 8 ethernet lines.
Thank you.
Steve

Cannot create WDS with Airport Extreme 802.11n and Airport Express b/g

I have gone through all the steps to set up a WDS with my Airport Extreme Dual Band and my Airport Express b/g.
Every time I try to set it up and update the AX the AX disappears from the airport utility and I can no longer see it. I can however set it up to "join a network" just fine.
Anyone have any idea why I cannot do this? I haven't seen anything saying that the AE is not compatible with the AX.
Ideally what I would like to do is have the AX extend the network and then use an ethernet cable to connect it to an imac g4, thus giving the computer "wireless" internet.
Any ideas or suggestions?
Thanks

So just to clarify even if I was to buy a new "n" AX I would still be relegated to "g" speeds?
That's correct if you use the WDS settings on both the AEBS and AX.
But, if you had the "n" AX, you could configure it to "extend a wireless network" and maintain "n" speeds on the network. There would still be some bandwidth loss...10-15% or so...that's unavoidable unless you go to an ethernet connection method.
Do you think for my application it might be better to just buy a reputable wireless usb dongle?
If I understand correctly, you need an ethernet connection for a computer. Why not consider a pair of ethernet powerline adapters? One device plugs in near your AEBS and the other near the device that needs the ethernet connection. The pseudo ethernet signal is conducted over the AC powerlines in your home. This is the next best choice when you can't run an ethernet cable through the house.
This would be a faster and more stable connection than any type of wireless application. It's plug and play. In addition to the powerline adapters, all you'll need are two short ethernet cables to connect one adapter to a LAN port on the AEBS and another short ethernet cable to connect from the adapter to the G4's ethernet port.
Any electronics superstore will have a selection to look at. The cost is approximately $75-125 for a pair depending on how much speed you choose.

If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

Hi I'm from Australia.
If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

Any specific recommendations for a standalone ADSL modem though?
Always a good idea to use the modem that your service provider supplies or recommends....often free....since you know that it will be supported in the event of connection difficulties.
I have made the mistake of choosing the "best" modem based on test reports....only to find out later that the ISP would not offer any support when I was having connection difficulties.
The ISP blamed the modem. The modem support folks blamed the ISP.

I changed my Airport Extreme network name and password, now I can't access my Airport Express speakers. Help please.

I changed the network name and password associated with my Airport Extreme and now my system is not recognizing my Airport Express speakers.
Can someone help me get my speakers and sound system back online?
Thanks in advance for any assistance.

You will need to think in reverse here.
Change the network name and password back to where it was on the AirPort Extreme and get things working that way.
Then, change the name and password on one AirPort Express, then the second. Both Expresses will be blinking amber at this time. Power them off.
Now, change the name and password on the AirPort Extreme.
Power up both Expresses and they will now join the AirPort Extreme network correctly since you have programmed them with the new network name and password.

Difference between AirPort Extreme base station and airport express

What is the difference between AirPort Extreme base station and airport express

Please see this Apple comparision document for details. Post back on any specific questions including your specific requirements.
http://www.apple.com/compare-wifi-models/

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

Airport Extreme Base Station and 2wire Modem / Router

I have Yahoo DSL with a 2wire modem / wireless router combo. I have an iMac and a MacBook both running Leopard. I can't seem to get the Back to my Mac feature to work. I'm currently running the trial version of .Mac. I'd like to get a full .Mac account but I want to be sure I can utilize the Back to my Mac feature. If I were to bridge an Airport Extreme Base Station to the 2wire would that solve my issue with Back to my Mac. Additionally I like the idea of being able to plug a printer of external hard drive into the Airport Extreme.
Any advice is greatly appreciated.

I got it to work. I purchased the Airport Extreme Base Station and took the following steps which I found here http://forums.macosxhints.com/archive/index.php/t-68141.html
First connect directly to the 2Wire with the Ethernet cable.
Instructions from 2Wire:
1. Clear the HomePortal to Factory State –can be accomplished two ways
2. Go to http://homeportal/management
3. Click on Resets
4. Click on Reset to Factory State
5. Click Continue
6. Have customer press Hardware Reset button with paperclip (HG products only and BellSouth HWs)
7. Have customer unbend a paperclip
8. Have customer insert paperclip into recess for Hardware Reset button (outlined with Red circle) on back of HomePortal.
9. Hold paper clip in for ten (10) full seconds
Next steps:
1. Go to http://homeportal/management again
2. Click on Configure under Broadband Link
3. Enter VPI 0 and VCI 35
4. Click on Disable PVC Search
5. Set Connection Type to Direct IP
6. Click Submit/Save
7. Have cu go to http://homeportal/management
8. Click on Configure Services
9. Have cu Uncheck Enable Routing
10. Click Submit
Airport configuration:
1. Open the AirPort Admin Utility and select your Base Station.
2. Click Configure and enter your password.
3. Click the Internet tab.
4. Choose PPP over Ethernet (PPPoE) from the Connect using pop-up menu.
5. If required by your ISP, enter your user name, password and service name in the appropriate fields. ( Your name and password is you full email including the @sbcglobal.net part and your email password)
6. Click Update.
7. After the base station restarts itself, quit the AirPort Admin Utility.
If that doesn’t work call apple and they should be able to help with the airport configuration.
Back to My Mac now works. Hope this helps someone else.
Message was edited by: WalrusBoy

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

Airport Extreme (4th generation) and "Wireless Client Mode"

Hello All,
I am using an Airport Extreme (4th generation) and I wonder why in "Wireless Client Mode" I am unable to connect my network using the Ethernet connection.
Basically, what I wish to do is a bridge between a Base Station Wireless N <--> Base Station Wireless N (Airport Extreme) distributing the connection via its integrated Ethernet ports.
Thanks,
Sebastian

I wonder why in "Wireless Client Mode" I am unable to connect my network using the Ethernet connection.
The Ethernet ports are not enabled if you configure the AirPort Extreme to "Join a wireless network". Oddly, the USB port is enabled.
If you have another Apple "n" wireless router as your main base station, you could configure the AirPort Extreme to "Extend a wireless network". This would provide more wireless coverage and enable the Ethernet ports on the device.
Ironically, the less expensive AirPort Express 802.11n will do what you want.
When the Express is is manually configured to "Join a wireless network", there is a special feature to "Enable Ethernet clients", which will activate the Ethernet port.

Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
Thanks

The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
Assuming your AE is gen3 or greater.
You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
If your AE is G wireless or earlier model.. really the time has come for replacement.
If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

I have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

i have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

Read the user guide:
http://support.apple.com/manuals/#airport

Airport Extreme, Apple TV and two Expresses

Similar Messages

Maybe you are looking for