Airport Extreme base station and Airport Express

I have both the above but have real trouble getting them to both join the same network. I want to use the base station to hook up to he internet and the Airport Express to drive my stereo in another room Both work fine on their own and on separate networks, but I have to switch from one network to the other if I want to browse or listen to music. Very frustrating. I feel sure I should be able to have both airports on the same network but I just can't get it configured. I am a newbie with WIFI so any help gratefully accepted.

The main base station, the AirPort Extreme, needs to be set up to "Create a wireless network". The AirPort Express needs to be set up to "Join a wireless network", which will be network created by the AirPort Extreme.
Is this how you have them configured now?

Similar Messages

Difference between AirPort Extreme base station and airport express

What is the difference between AirPort Extreme base station and airport express

Please see this Apple comparision document for details. Post back on any specific questions including your specific requirements.
http://www.apple.com/compare-wifi-models/

Airport Extreme Base Station and Airport Express network

Should I be configuring my Airport Express to extend the network of the Airport Extreme Base station or to be joining that network?

"Extend" if you want the Express to provide more wireless coverage in the area where it is located. This is a good choice for most users.
"Join" if you you don't need any additional wireless coverage in that area.
In both configurations above.....AirTunes is enabled and the USB port is active use with a "remote" printer.

Using both Airport Extreme Base Station and Airport Express

I am using a Airport Extreme and a AX, my goal is to use the base unit on one floor of the home and they AX as an extender.
I have linked the AX unit to join the existing network, now how to do I enable WEP 128 bit?

Here are the WDS setup steps...
AEBSn - WDS Setup
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete.)
Main Base Station Setup (AEBSn)
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the main base station, and choose Manual Setup from the Base
Station menu, or double-click the base station to open the configuration in a separate window.
o Enter the base station password if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the MAC address of the base stations you want to connect to this base station.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup (AX)
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the remote base station, and choose Manual Setup from the Base Station menu.
o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the MAC address of the main base station in the WDS Main field. The MAC address is also referred to as the AirPort ID and is printed on the label on the bottom of the base station.
o Click Update to transfer the settings to the base station.
(ref: Pages 41-45 of "Designing AirPort Extreme 802.11n Networks.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
Thanks

The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
Assuming your AE is gen3 or greater.
You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
If your AE is G wireless or earlier model.. really the time has come for replacement.
If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

Which version of the AirPort Utility are you using?

Airport Extreme Base Station and 2wire Modem / Router

I have Yahoo DSL with a 2wire modem / wireless router combo. I have an iMac and a MacBook both running Leopard. I can't seem to get the Back to my Mac feature to work. I'm currently running the trial version of .Mac. I'd like to get a full .Mac account but I want to be sure I can utilize the Back to my Mac feature. If I were to bridge an Airport Extreme Base Station to the 2wire would that solve my issue with Back to my Mac. Additionally I like the idea of being able to plug a printer of external hard drive into the Airport Extreme.
Any advice is greatly appreciated.

I got it to work. I purchased the Airport Extreme Base Station and took the following steps which I found here http://forums.macosxhints.com/archive/index.php/t-68141.html
First connect directly to the 2Wire with the Ethernet cable.
Instructions from 2Wire:
1. Clear the HomePortal to Factory State –can be accomplished two ways
2. Go to http://homeportal/management
3. Click on Resets
4. Click on Reset to Factory State
5. Click Continue
6. Have customer press Hardware Reset button with paperclip (HG products only and BellSouth HWs)
7. Have customer unbend a paperclip
8. Have customer insert paperclip into recess for Hardware Reset button (outlined with Red circle) on back of HomePortal.
9. Hold paper clip in for ten (10) full seconds
Next steps:
1. Go to http://homeportal/management again
2. Click on Configure under Broadband Link
3. Enter VPI 0 and VCI 35
4. Click on Disable PVC Search
5. Set Connection Type to Direct IP
6. Click Submit/Save
7. Have cu go to http://homeportal/management
8. Click on Configure Services
9. Have cu Uncheck Enable Routing
10. Click Submit
Airport configuration:
1. Open the AirPort Admin Utility and select your Base Station.
2. Click Configure and enter your password.
3. Click the Internet tab.
4. Choose PPP over Ethernet (PPPoE) from the Connect using pop-up menu.
5. If required by your ISP, enter your user name, password and service name in the appropriate fields. ( Your name and password is you full email including the @sbcglobal.net part and your email password)
6. Click Update.
7. After the base station restarts itself, quit the AirPort Admin Utility.
If that doesn’t work call apple and they should be able to help with the airport configuration.
Back to My Mac now works. Hope this helps someone else.
Message was edited by: WalrusBoy

If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

Hi I'm from Australia.
If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

Any specific recommendations for a standalone ADSL modem though?
Always a good idea to use the modem that your service provider supplies or recommends....often free....since you know that it will be supported in the event of connection difficulties.
I have made the mistake of choosing the "best" modem based on test reports....only to find out later that the ISP would not offer any support when I was having connection difficulties.
The ISP blamed the modem. The modem support folks blamed the ISP.

I have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

i have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

Read the user guide:
http://support.apple.com/manuals/#airport

Vonage, AirPort Extreme Base Station, and Comcast

I just picked up an Airport Extreme Base Station, and wanted to use it to get my MacBook Pro on my home network. However, I can't get it to actually provide an network connection to the MacBook. In the Network pane of System Preferences, under the Network Status, AirPort has a yellow icon, and the following message: "AirPort is connected to the network HulkNet. AirPort has a self-assigned IP address and may not be able to connect to the Internet."
Here's my current setup:
Comcast > Cable Modem > LinkSys RTP300 > PowerMac, PC, AEBS
I have the "Distribute IP addresses" disabled on the AirPort, and the internet for the PowerMac & the PC work fine. In the network status of the RTP300, the AEBS is listed as having an IP address of it's own.
Any gurus out there that can help me figure this out? I just want to be able to access my home network from anywhere in the house!

All,
I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes?

Airport extreme base station and expresses

Does anyone know how many airport expresses can work off of one base station? I have a airport extreme base station 802n about 2 years old. I currentoy have two expresses linked and would liek to add a third.
Also, is there any value in buying a current model base station --- in terms of wifi capability? It seems our movie download performance has signeificantly slowed in the last year as we hae more devices in our home that use wifi. Thanks

You might try asking this question in the Airport forum.
Here's a link for you:
https://discussions.apple.com/community/wireless/airport

Airport Extreme Base Station and Multiple Computer Access to the Internet

I have my IMAC connected to the internet via the Airport Extreme Base Station. When I am able to connect, my son's MacBook cannot. If I preform network diagnostics and reset the base station so he can connect (which appears to be luck on my part), I can no longer connect. When I first set this up, I had it working with all computers in the house. I tried to expand the system to boost the signal in our house with the airport express units. I have since removed them and started over, but still cannot provide internet access to more than one computer.
Help

Try this first...
Modem/Router Power ReCycling
- Power-off the DSL/Cable modem, Internet Router, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the DSL/Cable modem; Wait at least 30 minutes.
- Power-on the Internet Router; Wait at least 5 minutes.
- Power-on the computer(s)

Connecting Airport Extreme Base Station and HiTron CGN3

A recent installation of Internet/CableTV services by Rogers.ca replaced my Airport Extreme Base Station WiFi network with one based on the Hitron CGN3 Cable Modem/Router. Many of the WiFi enabled evices in the home were switched to the new network without too much hassle. However, my multiple NEST CO/Fire alarms failed to connect and after some hunting I established that the CGN3, although apparently ipv6 'compatible' has this protocol not enabled. There is no input facility in the modem setup to activate the protocol. The importer of the device seems to have chosen to not respond to such tech issues.
It now comes down to either using the CGN3 as a Modem/WiFi server or extending the network to include the Airport Extreme on the CGN3 (don't know how to do that) or vice versa, extending the Airport network to include the CGN3 (don't know how either).
QUESTION:
Does anyone have any idea on how to make the Airport Extreme and HiTron Modem/Router function together since the Extreme has the ipv6 protocol enabled and NEST (and other 'Internet of Things') devices will reconnect, no problem.
More Info:
The only reason for the CGN3 to remain as a WiFi server is its range which seems to cover the required service area with a more powerful, stable signal than the Airport. That is somewhat important since TV services come over the Internet and mobile devices apps available from the Apple store can be used as very capable program guides/selectors and remotes for the HDPVR and secondary HD boxes that feed the TVs, eliminating a remotes collection and associated programming and infra-red transmission hassles. I believe the Cable boxes would accept getting the TV signals from the CGN3 and function commands from the Airport Extreme networks. That remains to be proven. Level 2 Technicians at Rogers and NEST Labs have looked at this and can't access the CGN3's ipv6 function to activate it. They don't know much about the Airport Express.
Second Thought:
On the other hand, a second apple Airport base station would extend the network range to rival the CGN3 and the WiFi function of the CGN3 could be turned off. I tried to connect the two routers by LAN cable but they don't seem to see each other and I don't know enough about network settings to get any further.

Whichever airport you use.. express or extreme doesn't matter much..
It should be setup in bridge mode. Plug an ethernet cable from LAN port on the CGN3 to WAN port on the Apple router.
Go into the airport utility and run through the setup. Don't be too worried if it chooses the wrong setup.. you can go back and edit it after the setup is complete.
You will want to open the Edit.
Then go to the various tabs to ensure it is setup the way you want..
On the Network tab.. bridge mode.
On the wireless tab, create a wireless network.
I recommend you use names that are short, no spaces and pure alphanumeric. eg AEwifi In my case with Time Capsule I use separate wireless names for the two bands. TC24ghz and TC5ghz but that is up to you.. it can make life easier.. then set channels can also make things easier.
Ensure your IPv6 is setup correctly.
The actual internet option will be dhcp.
You will have two wireless networks.. but both will use the CGN3 as router.. the airport if it worked in the past should work. Even if it is not the dhcp server. BUT let me add there is another way to fix this if this setup doesn't work.. please post back your result.. no luck then I will show you how to setup a static IP with the Apple router.

Airport Extreme base station and Airport Express

Similar Messages

Maybe you are looking for