Airport Extreme Base Station as Wireless Adapter

I have a Verizon FIOS network coming into my house and connected to the supplied wireless router. Our three Macs are connected to it wirelessly, as our the iPhone and Touch.
I have a G5 in the basement that does not have a wireless adapter. I bought an older AEBS b/g model in hopes that I could connect to the G5 (with the LAN port) and wirelessly connect to my existing home network. Basically, I was hoping to use it as a wireless adapter.
Is this possible? I have been looking all over as well as in the documentation and cannot figure out how to do it.
Thanks for the help.
Jeff

I bought an older AEBS b/g model in hopes that I could connect to the G5 (with the LAN port) and wirelessly connect to my existing home network. Basically, I was hoping to use it as a wireless adapter.
Is this possible? I have been looking all over as well as in the documentation and cannot figure out how to do it.
Sorry, but no. Instead, the newer 802.11n AirPort Express Base Station (AX) could be used as an Ethernet bridge, which would basically do the same thing. With this type of bridge, you could connect your G5, by Ethernet, to the AX's Ethernet port and, in turn, the AX would connect wirelessly to your Verizon wireless network.

Similar Messages

Using Airport Extreme base station as wireless Cable router and airtunes.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
I would like this if it is a wireless standalone router as I want to but a pair of wireless airtunes router for music around the house keeping the Airport Extreme in my room where the airtunes routers would not be as I have the computer in my room and I have iTunes right there and would not need the airtunes routers in my computer room.
Leon.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
The AirPort Extreme Base Station (AEBS) does NOT have a built-in DSL/Cable modem. You will still require a Cable modem in order to access your ISP's Internet service.
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
The AEBS IS a wireless router, but it is NOT a combination wireless router & cable modem.

Airport Extreme Base Station as an wireless Extender to new Airport time capsule

After many months of time machine back up problems. (verify back up failing) I am considering biting the bullet and getting a new 2TB Airport extreme time capsule. Can I use the old (late 2013 801.11ac) airport extreme to extend wifi network?
A few other questions.
1.Does extending reduce wifi performance?
2. If using extreme as extender can I still plug in hard drive or hard drive to it?
3.
currently using imac 21.5 (late 2013) 1TB backing up to 6TB WD mybook live duo (connected to Extreme using ethernet), via airport extreme base station (ac wireless band to mac)
Any guidance appreciated.

Is it possible to quantify how much faster USB back up is compared to 802.11ac between mac and AirPort time capsule?
600GB should take 10 hours by ethernet. And it will be somewhat faster by USB3.. exactly how fast is difficult to predict as the first TM backup itself is slow due to many small files. In terms of raw speed maybe twice but it will depend on the disk used. USB you can use an SSD and get super huge speed. (not that I think you will be buying a 1TB SSD anytime soon).
In terms of raw speed it is cheese and chalk. The max speed of real world file transfer on AC wireless is around 430Mbps and that is using ideal world.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/113-5-ghz-dn-c?see=MAX
This has nothing to do with link speed.. this is how fast a file actually transfers. And that is assuming the iMac and the TC are in the same room. And everything is perfect with nothing else using connection.
The real world speed of USB3 is around 100MB/s to a spinning hard disk..
http://www.macworld.com/article/2039427/how-fast-is-usb-3-0-really-.html
which may indicate the limit is the actual disk speed. In bits per second you x 8.. so the USB3 is 800Mbps. The advantage of USB direct connection is that speed is available at all time. Not when your close or the load on wireless is low.
Further to your comments when extending. Is it only the area covered by extending that has reduced performance or all the wifi signal?
The speed will depend on hops..
So if the computer is using resources on a local router.. and only one wireless hop then it is fast.
If it is using resources via a second router so wireless goes.. computer--- router2----router1-- resource.
Your speed drops 50% at best.. at worst it is really bad.
For example.. computer 1 on router 1 accesses computer 2 hard disk on router2 with everything wireless.
Count the hops. C1-R1, R1-R2, R2-C2
That gives 3 hops. So each packet is transmitted.. along that chain.. each transmission can only begin after it is received in full. Now add some other computers using resources.. say C3 is using internet via R1.. that has to be time sliced. So you get 50% of 50% of 50% of 50%. It is obvious that wireless networks have a huge handicap.. they cannot transmit and receive at the same time.. nor can they talk to more than one client at a time.. so add time slicing to wireless hopping.
Now ethernet is entirely different. It can transmit and receive at the same time.. ie is duplex. And in a switch it can talk to several computers at the same time. That is why we say.. as much as you can ethernet.. and use wireless as the last single hop to a client that needs it.. ie iphone or ipad.. or laptop if you cannot plug in ethernet.
Can the ac wifi format be extended using AirPort Extreme and time capsule.
Over very short range yes. AC wireless is only on 5ghz and is poor penetration of solids.. so this will work but maybe only to the next room.

Airport Extreme Base Station - Wireless AND Hardwired connections

I have an Airport Extreme Base Station. I am under the impression that I can connect a hardwire via ethernet to my iMac, as well as use my wireless connections on my iBook. I am connected to the internet via my local Comcast Cable system on a SurfBoard SB4100 modem. I have one Ethernet port on the back of the Base Station connected to a Farallon iPrint Adapter for my antiquated (yet far more reliable than ANY injet I've owned) laser toner printer. I have a McAlly 5-port ethernet hub. I have a variety of ethernet cables, some with 8 wire connections, some with 4 wire connections. (Currently a 4-wire cable connects from the base station to the iPrint adapter) My total system has been dismantled for some time and I have been sailing through with the wireless connection on my iBook. But now I have a need to have both computers attached to the internet. I would rather have the hardwire connection and the wireless at the same time - if possible. The iMac is still on system 9 (stop laughing!) and I cannot afford to upgrade to 10 at this time.
Can anyone help me?

I am under the impression that I can connect a hardwire via ethernet to my iMac, as well as use my wireless connections on my iBook.
Yes that is possible.
Insert the Ethernet hub between the Farallon iPrint Adapter and AirPort Extreme base station (AEBS).

Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network with newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

My Power Book G3 Pismo with an Airport wireless card running Mac OS X 10.4.11 will not connect to my new Airport
Extreme Base Station using WPA Personal/WPA 2 Person encryption. The Airport firmware is version 9.52. From
posts I've read online at different places indicates the Airport card should support the WPA encryption. Perhaps the problem
is the Base Station is using a combination setting and the fault is in the base station?
Thanks for any suggestions

Perhaps an inexpensive usb wireless adapter would work as well?
This is probably the simplest way to get the G3 connected to the wireless network.
I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
The new AirPort Extreme is broadcasting a wireless signal.
A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable.
This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
I do have an old Linksys Wireless G router. I wonder if that would work?
In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

Problem consistently printing via new (summer 2011) AIRPORT EXTREME BASE STATION and Brother wireless printer (model HL5370DW). What am I doing wrong?

Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
My theories:
- true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
- The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
QUESTIONS:
- Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
- I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
Rule out:
- wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
Any help will be greatly appreciated.
Thanks in advance!

13 ASCII characters = 104 (aka 128)-bit WEP
encryption
If turning off WEP works, then you just need to
provide the cameras with the "Equivalent Network Password".
One of the problems with WEP is that the actual
standard relies on a 10 character HEX key for 40bit
WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier, vendors use certain
algorithms to convert simple alphanumeric passwords
(or passphrases) into HEX keys, thus enabling the use
of simple easy to remember WEP password rather than
lengthy HEX keys. The problem is that different
vendors use different algorithms to generate the HEX
key and therefore a ASCII password on an AEBS will be
hashed differently on a non-Apple client and vice
versa.
You may find the following article helpful:
- Apple article, especially the part about
"Third-party client to Airport".
Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
Thanks again for your help and suggestions... I really appreciate it.
geoff

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

HT4259 How do I set up an Airport Extreme Base Station (v. 7.6.1) to allow wireless network extension?

I have an Airport Extreme Base station (purchased in 2009) and an Airport Express base station (purchased in 2011 - the model that plugs directly into the electrical outlet) (both version 7.6.1 according to the Airport Utility info). I want to use the Airport Express to extend my wireless network. Using Airport utility setup I have a software option on the Airport Express to set it up to extend the network but I do not have an option on the Airport Extreme wireless setup screen that I can check to allow my wireless network to be extended.
All of the documentation I can find on Apple Support states that I should have an option I can check to allow the wireless network to be extended while in the wireles setup section for the Airport Extreme in Airport Utility; but, that check option isn't there. Is this a case of my Airport Extreme base station being too old to offer that option? Incidentally, when I try to select the extend wireless network option on the Airport Express from the Airport Utility wireless setup menu I get an error message (no details - just an error message). The same Airport Express sets up fine if I select join a network (not what I want to do). Am I just dealing with outdated equipment or does anyone have a suggestion? Thanks.

Close AirPort Utility if it is open.
Temporarily, move the Express to the same general area as your AirPort Extreme and power it up and wait a minute.
Hold in the reset button on the Express for 9-10 seconds and then release. Give the Express a full minute to restart to a slow, blinking amber light.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear
Click on AirPort Express just below that and AirPort Utility will automatically open
Wait a minute while AirPort Utility analyzes the network and announces that the Express will be configured to "Extend" the AirPort Extreme network.
Enter a device name for the AirPort Express and click Next
Wait another minute to allow the configuration to occur.
When you see the Setup Complete message, click Done.
Now move the Express to a location that is approximately half the distance from the AirPort Extreme and the general area that needs more wireless coverage
Power up the Express and you are all set. Trash those old instructions.

How do I configure an Airport Extreme base station to receive and distribute a wi-fi network from a broadband wireless router?

I have recenly upgraded my broadband service and now have a wireless router. My old network configuration was a router connected by ethernet cable to an Airport Extreme base station which then broadcast my wireless network (I also had an Airport Express base staion set up as a wi-fi booster elswhere in the house).
I now have two networks (my original network and the new network from the wireless router) and wish to amalgamate these into one.
Ideally I wish to use the Airport Extreme base station as the "remote" booster (I have purchased Powerline adapters for this purpose) but don't know how to configure the Airport Extreme base station in order to to this.
Can you advise on the best set up for this please?
My Mac is running OS X 10.8.2 and the Aiport untility is version 6.1.
Thanks in anticipation.

The AirPort Extreme should be configured to "create a wireless network" with the same WiFi network name, security type (usually WPA2 Personal) and password as your existing router. It should be configured as connection type Ethernet and be in bridge mode.

How can I extend a wireless network with my AirPort Extreme Base Station?

Today I purchased a brand new, dual-band base station to replace my Belkin N router, as I have had a handful of firewall, coverage, and other networking problems in my house lately. First off, I really like this router and it was very easy to setup. My MacBook Pro could use both bands and established a 300 Mbit/s link very quickly. After tweaking various settings to my liking, I was also able to maximize the connections on many of my non-Apple machines and devices. I noticed that the range of its network was better than my Belkin's, but unfortunately, it failed to completely saturate the area sufficiently. Since the Belkin still works well enough, I was hoping I could bridge them together one way or the other.
The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct? I would like to place them at opposite ends of my home so I can get strong WiFi signals everywhere inside. However, when I try to get the base station to connect to my preexisting WiFi connection, it tells me that I can't extend the network and fails to join.
So is this possible? And if it is, how would I go about setting it up? I know it would probably be easier if I had a simple range booster such as an AirPort Express, but I didn't buy one while I was at Fry's since I hoped I could make use of the older Belkin. This is its product page, if needed. Thanks for any suggestions.
-MacUser

The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct?
Sorry, but no. The AirPort Extreme Base Station cannot "join" a network like the AirPort Express or Time Capsule, but you wouldn't want to do this anyway because in this configuration these devices will only perform as wireless clients ... not routers.
Instead, the AirPort Extreme can either be extended or can extend another 802.11g or 802.11n AirPort ... or a very very few non-AirPort devices.
One option for your Belkin would be to connect it to the AirPort Extreme by Ethernet but this may not meet your requirements or be a desirable situation. Otherwise, you would need to get another AirPort to extend your current one.

Multipmultiple Airport Extreme Base Stations: WDS Or "Extend Wireless Network" To Have Wired -- Wireless Bridge?

Hello there!
I've been looking for this info, but have as yet been unable to find it. Here's my scenario:
I have two Airport Extreme Base Stations (both are dual band) and 3 airport expresses. The main internet connection in my house is in one room, where I have an AEBS as the main wireless router. In another room, I have a bunch of ethernet-only devices. I'd like to use the 2nd AEBS in this room, plug the ethernet devices into it and have the 2nd AEBS act as a wired <--> wireless bridge (connected to the same wireless network as the 1st AEBS). I've attempted this via "extend a wireless network," but the ethernet devices don't get past the AEBS they're plugged into. Should I instead be implementing WDS?
I mention the airport expresses as I'd like to have airtunes & wireless signal in other areas, but would like to keep the set-up as simple as possible (i.e., not config the AXes for WDS unless it's required).
Thanks in advance for any help!

Unlike the 802.11n AirPort Express Base Station (AXn), the 802.11n AirPort Extreme Base Station (AEBSn) cannot be configured as a wireless Ethernet bridge.
However, there are at least two ways to configure it to provide wired clients access:
Connect the second AEBSn back to the first by Ethernet; reconfigure the second AEBSn as a bridge and disable its wireless radios, or
Reconfigure both AEBSns into an extended wireless network. For 802.11n AirPorts, this would be called a dynamic WDS. The AEBSn, connected to the Internet would be the "main" base station and it would only require that you enable the "Allow this network to be extended" option in the AirPort Utility. The extending AEBSn would need to be configured with the option, Wireless Mode = Extend a wireless network, enabled.
In both configurations, the second AEBSn's Ethernet ports would be enabled for wired clients.

Wirelessly Connecting HP Laserjet P3015 to Airport Extreme Base Station

Hi, I just purchased a new Airport Extreme Base Station, and was able to establish an internet connection to it. I'd like to find out if it's possible to connect the HP Laserjet Enterprise P3015 to the Extreme, wirelessly rather than via a USB Cable. I've looked at the HP page for this printer, but I'm baffled by all the lingo. I believe it's a newer model of HP printer (or maybe it isn't?) but I bought it new from HP recently.
http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=S upportFAQ&lang=en&cc=us&docIndexId=64178&taskId=101&prodTypeId=18972&prodSeriesI d=3815797&printver=true#10
Is there a term for the type of printer that can be wirelessly connected? Should the printer, by default, give off a signal that I can pick up? I don't see anything popping up in Airport Utility 6.3
I'm using OS10.7.5 by the way.
I'm off to post a message on the suitable HP forum (if I can find it ) but I'm so used to the Apple Community knowing what's what, that I was hoping that some kind soul here might just have experience with this.
Thank you.
PS. From what I can understand from the "Trouble-shooting FAQ," wireless printing is possible, but I just don't see an option for syncing it up with a MAC? Maybe it only works with Windows?

wuzradioman
I don't see where the P3015 printer is wifi capable. Therefor, you cannot use wifi to directly communicate with it.
Thanks for the reply Wuzradioman. I dug around (several) of HP's sites and it looks like the info was slightly different for the same printer listed on both the Home and Business sites. I did find a link on a 3rd HP page (which I've since misplaced!) that indicates that the P3015 requires a wireless card to be installed. But when I clicked the link for "accessories and additional hardware" a link to the card was nowhere to be found. I'll try to dig up that link in the event that some other poor soul has the same printer and a similar question.
Vernon Alexander
I find the HP printers (they're called wireless printers by the way) to be cumbersome to connect wirelessly. there's a lot of manual work involved that can be time-consuming. For example, I found it incredibly irritating to enter the wireless access passcode.
Thanks for the reply. After talking to some other people, this seems to be the consensus on wireless printing. I guess there's a reason, esp. in enterprise environments, that printers are often hard-wired.
Bob Timmons
you can run an Ethernet cable over a much longer distance than a USB cable, so Ethernet might be the best option, and the one I would prefer.
As far as wireless, If you connected an AirPort Express to the printer and disguised it near the printer, then you could locate the printer anywhere you want and have it connect using wireless to the network.
Instead of installing a wireless "card" inside the printer, you use an outboard device to accomplish the same task.
Thanks Bob. I did end up hooking up via a Cat-5e cable from printer to Airport Extreme base. Previously, I had the printer hooked up via USB cable (at a shorter distance) to my Airport Express, which the Extreme now replaces.
Unfortunately, I can't seem to get the HP Laserjet P3015n printer recognized after having connected it via Cat5e cable to the Airport Extreme. 1) there's still somethign about it being attached to the old Airport Express (which is now used to extend my network. 2) The P3015 is identified as a P3010 - which is a carry-over from when I had originally set up the printer on my (then) main base station which was the Airport Express. I didn't (or rather "stopped") questioning the fact that the P3015 was recognized as a P3010 just because it was the only way I could get the printer to be recognized at the time.\\
But I suppose this new challenge merits a separate thread, which I'll start after I do a search of the support forums. Maybe there's something obvious I'm not doing to get the printer sorted out.

I have a Cisco wireless router. Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

Using Airport Extreme Base Station As A Wireless Card?

Hi,
I don't know if this is even possible but here's what I'd like to do:
I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station. So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
Here's my real question:
I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
If this is possible, how can I do it?
Thank you in advance for any help with this.

Ernest Lohrer wrote:
Hi,
I don't know if this is even possible but here's what I'd like to do:
I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station.
She has an "integrated" modem/router/access point.
So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
Here's my real question:
I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
If this is possible, how can I do it?
Set up the AEBSn as a "bridge" and connect the G4 Mini to one of the "wired" internet connections.

How to get this Airport Extreme base station to produce a wireless network?

I had this Airport Extreme base station working fine at the house that I moved from a couple of days ago.
After my house move, however, it seems that the AE base station isn't producing a wireless network. My wireless laptop isn't detecting a wireless network. Also, the left hand side light on the AE base station is not lit.
The AE base station was softly cushioned during house the move.
Regarding configuration:
My non-wireless iMac (running 10.3.9) connects to the AE base station via an ethernet cable.
Before my house-move, I regularly connected wirelessly via the AE base station from a couple of wireless-equipped laptop computers.
I was using AE software version 5.6. (In desperation, I have just updated to version 5.7 - but that hasn't improved or changed situation.)
At the new house, I found that I had to reset the AE base station back to factory settings before I could successfully connect to the internet through the AE base station from the (non-wireless) iMac.
Since resetting the AE base station at the new house, I can also print via a USB printer that's plugged into the AE base station.
I just cannot pick up any sign of a wireless network from the AE base station.
G4 Powerbook Mac OS X (10.3.9) Problem started while I had Airport Extreme software v5.6. No improvement/change after v5.7 update.

Sorry for my delay in closing this issue.
I got the wireless network running again - though I'm not sure which of a "litany" of separate actions (which I gleaned from dialogs in several similar postings for similar issues to mine) was the solution. I suspect it was one of the following two actions, which have stuck in memory:
1) I relocated a nearby cordless phone cradle/charger/base-station from alongside the Airport Extreme base station to about seven feet (two meters) away. However, the cordless phone is about eight years old, and I believe its radio frequency is far out of the range that I have read (in similar postings) can interfere with the Airport Extreme base station.
2) I re-set the Airport Extreme base station, (a) by depressing the tiny reset button at the rear of the base station for more than 5 seconds (until the led started blinking), (b) from Utilities/AirPort Admin Utility/Configure/Restart. However, I had reset the Airport Extreme base station those ways previously without that restoring the wireless network. Also, I didn't record the sequence of the multiple resets and the configurations at the times of the resets.

Airport Extreme Base Station as Wireless Adapter

Similar Messages

Maybe you are looking for