Airport extreme base station do i have to connect a modem

just bought a base station connected it to a BT home hub(which constantly dropped the wireless connection on both windows and mac)and it works really well fast and no drops
the only question i have is i thought it was a wireless router why do i have to connect it to a modem the guy in the Apple Store said i just had to connect it into the broadband plug but this didnt work??

The AirPort Extreme base station (AEBS) must connect to an Ethernet connection. Usually this is provided by an ISP's modem or ISP's modem/router combo device.
Typically you would connect the AEBS's WAN port to the Ethernet output of the BT home hub.

Similar Messages

  • If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

    Hi I'm from Australia.
    If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

    Any specific recommendations for a standalone ADSL modem though?
    Always a good idea to use the modem that your service provider supplies or recommends....often free....since you know that it will be supported in the event of connection difficulties.
    I have made the mistake of choosing the "best" modem based on test reports....only to find out later that the ISP would not offer any support when I was having connection difficulties.
    The ISP blamed the modem. The modem support folks blamed the ISP.

  • Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

    I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
    The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
    Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
    Thanks

    The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
    If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
    So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
    Assuming your AE is gen3 or greater.
    You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
    And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
    If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
    If your AE is G wireless or earlier model.. really the time has come for replacement.
    If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
    You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

  • DrayTek Vigor 120 + Airport Extreme Base Station?  I have queries.

    Ok, so my 3 or 4 year old USR 9108 router went down today-- again. I'm fed up and want a new one. It dies on me once or twice a month. It has decided it doesn't like my powerline adapters lately. and I'm fed right up. I run an internet radio station and what I need is stability.
    At the moment, I'm thinking of setting up a DrayTek Vigor 120 ADSL modem (modem-only) with the Airport Extreme Base Station for my router. (I already have an Express on my network.)
    First of all, can anyone please comment on whether they have this set-up and whether it's solid? I've heard good things about both of these devices, and I need something that's not going to flake out as regularly as my USR has been doing of late. Rock solid is a good thing for a 24/7 stream.
    Second, can I just confirm a few questions that I think I know the answer to, but want to be sure before shelling out?
    I am in the UK using an ISP that uses PPPoA; so I need to be sure the modem has a PPPoA to PPPoE bridge in order for the Airport to talk to the outside world. (Right?). I gather the DrayTek will do this. Will it therefore be just a question of setting the Airport to connect via PPPoE and then entering my ISP login settings in Airport Utility?
    I need a setup ideally that, like the USR, will allow me to assign IP addresses manually to some machines or devices on my network but allow DHCP on other things (like my iPhone). It's particularly important that the radio stream should have a static IP. I gather, from having a play with my Express's settings, that I'll be able to accomplish this either directly or by DHCP IP-reservation. Directly would be preferable. Therefore, if I, e.g., assign my computers an IP address on their local network settings and then just shift the Airport's DHCP range so that it starts with (say) 192.168.1.10, rather than, 192.168.1.2, will the Airport be happy with that?
    I also need port forwarding / port mapping. This should be o.k., right?
    Thanks for help, people.

    I'm running a very similar setup here in the UK. I use a Netgear DG834 rather than the Draytek 120 which I was looking at. I use a Time Capsule connected to the router which is in half-bridge mode and this allows me to connect using PPPoE, which is possible on the BT ADSL network, which I didn't know before! - there's no need to get an expensive PPPoA-PPPoE bridge. I guess the Draytek would do an even better job than the Netgear, but mine was the free solution
    I use the TC to give out addresses to a network of various kit, with one fixed IP for a specific device. I find the TC and my airport express very easy to set up and run, if slightly light on the details of what's actually going on. That said, if it doesn't work, then they're probably broken!
    Nothing you've asked for is out of the ordinary / impossible on the apple kit.
    Hope that helps!

  • HT3500 I am trying to hook up my new Canon MG5320 printer wirelessly to my MacBookPro with OSX.8.2.  The Airport Extreme Base Station does not have a WPS button and so I seem to be stymied even though the printer detects the Airport Extreme.  Suggestions?

    I am trying to set up my new Canon MG5320 printer to my wireless network.  However, there is no button on the Airport Extreme to push when I get to that step in the set-up directions.  I am using OSX.8.2.  Suggestions please!

    If the display shows the "Press and hold the WPS button..." message on the MG display, press the red Stop button on the MG and then select Standard Setup. The MG will search for networks and should display your Airport Extreme's network name. Select this and then enter the password to connect to this network.

  • How do I view a file from a usb hard drive connected to my airport extreme base station on my ipad 2?

    Hi,
    I just purchased the airport extreme base station.  I have a usb hard drive connected to the base station.  Is it possible to view this hard drive on my ipad 2?  I have been unable to do it.  Any help would be appreciated.

    You can't, not natively. An app like FileBrowser:
    http://www.stratospherix.com/products/filebrowser/
    may make this possible, though.
    Regards.

  • Can't get PC laptop to connect to Airport Extreme base station. Help!

    I've spent a lot of quality time on the phone with support staff at Apple, Earthlink, and Netgear. Now I turn to you fine folks.
    I have an Airport Extreme base station. My G4 is connected to the base station via ethernet, and that works fine. My problem is with the wireless networking with our Dell laptop running Windows XP SP2. Wireless card is a Netgear WG511 with updated firmware. I've configured the network on the PC end using the Netgear Smart Wizard, rather than Windows (I don't know if that makes any difference).
    Smart Wizard says the PC is connected to the network, and says that signal strength is excellent. However, there is no connection. I've tried pinging, but get no reply.
    The status bar in the Smart Wizard window switches every 2 seconds from "Connected" with excellent signal to "Searching" with virtually no signal. The log shows that it's constantly connecting to and disconnecting from the network.
    I've gone over IP and MAC addresses and whatever other settings I could check with all of the respective phone support people. I'm using WPA/WPA2 Personal security, and have double-checked the 13-digit password on both ends. I'm connecting using PPPoE, per Earthlink's settings.
    This is maddening! Any suggestions? I'd really appreciate it.
    G4   Mac OS X (10.4.10)  

    See if iFelix's suggestions work for you.
    http://www.ifelix.co.uk/tech/1000.html
    Remember all the smart wizard stuff is strickley for PC Hadrware and Software and does you no good at all with a Mac.
    Don

  • Airport Extreme Base station and speedtouch modem router

    hi
    i was wondering will my speedtouch(THOMSON ST585v6sl) modem router (wireless) work with the Airport extreme base station? or do i need a modem only?
    thanks in advance

    Welcome to the discussions, dood!
    The Thompson ST585 appears to be a combination modem and router, so you could use one of the LAN ports on that device to connect an ethernet cable to the WAN port on the Airport Extreme. In this configuration, the Extreme would act as a "bridge" to the Thompson, which would function as the main router and supply the IP addresses for the network. You would be able to create a wireless network with the Extreme in this setup, but only the "main" network would be active. In effect, you have two routers in this setup.
    If you connected the Extreme directly to a modem only, then it would serve as the main router for your network and you would be able to make use of the "dual band" wireless capability of the Extreme to create a "main" and "guest" wireless network. There are 3 LAN ports on the Extreme that you can use for ethernet devices.

  • Mac book cannot find airport extreme base station

    Hi
    Basicly, the airport utility cannot "discover" the base station. Ever so occasionally it finds it but when i click on continue it says "there was an error connecting to the network"
    I have tried restarting the airport extreme several times.
    Please help!!
    Tom

    Have you tried doing a hard reset of the AirPort Extreme base station (AEBS)?
    Have you tried temporarily connecting to the AEBS via Ethernet to configure the AEBS?

  • Comcast HSI, AirPort Extreme Base Station issues

    Recently, I've been having some connection issues with my Comcast High-Speed Internet and my AirPort Extreme Base Station. I'll be connected fine one minute, and the next my AirPort monitor drops to 2 bars of signal and nothing will connect. Resetting the base station and the modem works about 50% of the time, while just sitting here "dealing with it" works the other half of the time.
    I rent my cable modem from Comcast, and I believe it is the Terayon TJ715. I went to the Apple Store San Francisco and had my base station replaced, thinking it was the culprit, but alas, the problem is continuing, only less frequently.
    I've replaced all my ethernet cables, tried it with my AirPort Express (which works more often, yet has the same problem occasionally), yet my connection uptime and signal still drops to 2 bars and essentially disconnects.
    Even stranger, the computer I have connected to the LAN port seems to work fine even when the computers connecting wirelessly are having issues.
    I'm going down to a Comcast Support Center on Friday to (hopefully) replace my modem with a newer model (someone told me that older Comcast modems "kill" AirPort Base Stations), but other than that, any ideas? Anyone have this type of issue with Comcast in the past?
    The 3 machines im running are:
    Dual-Core 2.3Ghz Power Mac G5 via AirPort
    867MHz PowerBook G4 (Titanium) via AirPort
    800MHz iMac G4 (Flat-Panel) via Ethernet
    Thanks,
    Alexis
    Dual-Core 2.3GHz Power Mac G5   Mac OS X (10.4.3)  

    Don,
    Thank you for the link. However, it did not seem to solve my issue.
    It's not that I haven't been able to connect to the internet at all using wireless. I will be connected fine (all 3 computers connecting to the internet simultaniously) when suddenly, any machine connected via AirPort (specifically my Dual-Core Power Mac G5) will receive two bars of signal and will no longer connect to the internet. The only remedy I've found is to reset both the cable modem and AirPort Extreme Base Station, and this only works about 50% of the time.
    I am going to have Comcast replace the modem (and in the meantime, get new Ethernet cables) tomorrow, so hopefully I won't be having this issue anymore, but I'm more curious what may be causing the issue. Have you heard anything about older Comcast modems causing latency issues with AirPort Extreme Base Stations?
    Thanks again,
    Alexis

  • Purchase of new Airport Extreme Base station??

    have i wasted money on purchase of NEW Airport Extreme base station? i have fios with actiontec router and tv service.  the Guest network does not work nor does Actiontec have ability to provide guest network. I am about to return the AEBS as I dont see any reason to keep it other than the 2.4 and 5GHZ network ability.  Oh yeah, the 802.11 ac too.

    Find a way to disable DHCP on your Actiontec router, making it a modem. Call Verizon and ask them for instructions: "I have my own router, and want to disable the Actiontec's router. How do I do that?"
    Here is one such question, from Verizon's support forum: http://forums.verizon.com/t5/FiOS-Internet/Disable-Actiontech-DHCP/m-p/281653#M1 9622 Try that.
    The AirPort Extreme can be configured as a bridge, i.e. not performing any router function, but you will be losing most of its advantages by doing so.
    Guest Network must be created by your router.

  • Maxtor Personal Storage 3200 and Airport Extreme Base Station

    I recently purchased an external hard drive and the newer Airport Extreme Base Station. I have two computers. 1 Macbook Pro and 1 PC running Windows Vista. I am having trouble downloading files from the HD over the Base Station to my Vista Machine. I can connect the drive directly over USB to my vista machine and the problem disappears. But when downloading files to Vista over the AEBS i get an error about the Path not existing. I then tried it on my Macbook Pro with no difficulties. I then fired up Parallels and installed the software on my Windows XP image and it works fine. My question is has anyone come up with a fix for this interaction between the AEBS and Windows Vista.

    You said you are "using the express to extend my range and play tunes using air tunes". How did you manage to set that up, if neither the Airport Admin Utility nor the Airport Setup Assistant won't allow you to configure these two devices?
    Two suggestions:
    1. try using another Mac or PC
    2. look hard to make sure you don't have some sort of third-party firewall software or VPN client software running on the Mac than is unable to configure your Airport devices.

  • Airport Extreme Base Station Internet Connection issue

    I have a connection question for Airport Extreme Base Station.
    I have Comcast cable broadband. I connect that to a Linksys router for
    use with my Vonage phone, and then from the Linksys router I connect
    via Ethernet to my iMac. I like the direct Ethernet connection for
    performance reasons.
    In order to set up a home network to connect my Tivo's (and eventually
    my PC and printer), I have set up an Airport Extreme Base station and
    connected it to the Linksys router from it's ethernet connection to the
    WAN (cable modem) input on the Extreme.
    I have connected to the Airport network with my iMac, but since I am
    connected to the Internet via Ethernet, I cannot tell if my Airport is
    connected to the Internet so that I can use it for my Tivo. My PC is
    still in storage from a move, so I can't check with that.
    My question: How can I tell if my Airport is connected to the Internet
    without disabling my Ethernet connection on my iMac?
    A few more info points/questions in case it helps answer:
    1) I previously used this Airport to connect this iMac wirelessly.
    2) Should I be connecting it to the LAN port since it's coming out of
    the router?
    3) If the connection issue is because I am going through the Linksys
    first, can I connect the modem to the airport and then use the LAN port
    to connect to the Linksys router?
    4) If I have to disable the ethernet connection to test the Airport,
    how do I do it? Just unplug it?
    I appreciate any help as the online and manual help from Apple is not
    quite up to par with such a complex configuration.
    Regards
    Bill

    2) Should I be connecting it to the LAN port since it's coming out of
    the router?
    No, connecting to the WAN port is fine.
    3) If the connection issue is because I am going through the Linksys
    first, can I connect the modem to the airport and then use the LAN port
    to connect to the Linksys router?
    The issue is that you have two routers which effectively creates two networks. Unless this was your original intent, you will want to setup the AEBS as a bridge.
    To set up the AirPort Extreme Base Station (AEBS) as a bridge, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, make these settings:
    Network tab
    - Distribute IP addresses (unchecked)
    - Apply the new settings.
    - Wait at least 5 minutes.
    4) If I have to disable the ethernet connection to test the Airport,
    how do I do it? Just unplug it?
    Well, that's certainly one way, but an easier way is to temporarily disable the "Built-in Ethernet" in your network configuration.
    System Preferences > Network > Show > Network Port Configurations
    - Built-in Ethernet (unchecked)

  • Have 2 airport extreme base stations connected in chain.  Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink.  Anyone have any ideas?

    Have 2 airport extreme base stations connected in chain.  Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink.  Anyone have any ideas?

    Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
    As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
    Power off the AirPort by pulling the power cord
    Wait a minute or two
    Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
    Release the reset button and allow a full minute for the AirPort to restart
    Now try to configure the AirPort again.  If you continue to see the same symptoms as before, the AirPort will need to be replaced.

  • I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

    I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

    Which version of the AirPort Utility are you using?

Maybe you are looking for