AirPort Extreme Base Station (Dual Band) vs Apple TV

I recently "Upgraded" my WiFi network from the original single band AEBS (802.11n) to the new Dual Band model. Since doing so, my TV cannot connect to the wireless network. The TV can "See" the network, asks for a password, but shows "Failed to connect" error message. I have tried changing the radio channels (using the "option" key and running through all possibilities). I have turned off "Security" and tried to connect as an "Open" network. It will not connect. iTune does not "see" the TV nor does WiFi utility AirRadar. I wonder if the 802.11n card in the TV is toast? Anyone have any ideas?

As suggested, I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.
Message was edited by: Mac MD

Similar Messages

Airport Extreme Base Station Dual Band

I just bought this base station to replace my old router. I downloaded and installed the airport utility on my vista laptop and ran the software and everything set up fine except a double NAT error which I ignored.
My laptop connects wirelessy just fine to the airport but no other devices can connect. I am using WPA and also tried without any security and no dice.
I am trying to connect 2 iphone 4s, xbox360, ps3, wii and none of them can connect. I have DHCP turned on and connection sharing set to share a single ip address.
The three game systems tell me that they cannot obtain an ip address and the iphone just say unable to cconnect. I have tried the WPA password I created and the HEX equivalent and no luck. I have also tried MAC filtering and added the MAC addresses of the devices and still no luck.
I am sure there a simple solution or sime box that is not clicked but I can not seem to find out what the problem is.
This is driving me crazy paying almost $200 for a router that gets nothing but great reviews and I cannot connect to it. Please help!

Bob: I am so happy to see you on this forum -- you recommended someone else come here for Airpor/Windows issues and so I did.
I have read all of your postings about setting up AX in client mode with my new Airport Extreme router. I did a factory reset on the AX, and the latest version of Airport Utility (OS= XP) can see it after the reset as well as the Extreme. I wrote down the network name and password type just like you recommended from the appropriate screen "Wireless" tab on the Extreme. But then when I login to the AX (right next to the router) the Extreme disappears from the Utility program side window. I put the appropriate info into the AX and it wrote to the unit and then said it would restart, just like you said it would.
BUT then it scans and can't find the AX only the Extreme. The Extreme is happily sitting there in the Utility side screen but no amount of scans will produce the AX. Which is also happily sitting there plugged in to the wall with its amber light flashing. I have done this over and again. I also checked to see if I had set up access control on the Extreme by mistake but it isn't turned on.
So I think I have ruled out interference, and I think since the AX works the first time before it disappears on the restart that the unit works. I have gone into the Windows firewall and added every possible relevant port including itunes in both the UDS and the N mode (those three letter acronymns). In any case the firewall is not alerting me to a block and it is set to tell me if it does block something.
I usually visit the genius bar but i can't really take in the Extreme as it wouldn't be connected to the DSL at my home. Plus I kind of like reading the forums as I learn so much.
And even if you don't answer this I want to say how much I appreciate your conscientious posts. If you set up as a consultant let me know.

Airport Extreme Base Station Dual Band has WiFi problems.

I can only connect my Droid X to the wifi network of my Apple Airport Extreme? I have an Ipad and another computer with a wifi dongle but none of them will connect. Only ethernet connected computers and my DroidX works. Any suggestions?

Hello garydicksonuk. Welcome to the Apple Discussions!
I have the Airport set up to "connect via ethernet" and "share a public ip address"? (I don't understand what this means, share public ip as not computer literate).
This would be the AirPort's default setting and what you will want 99.99% of the time. The "Share a public IP address" is referring to the fact that your AirPort provides a service that allow multiple clients on the local network to be able to access the Internet at the same time. This service is known as Network Address Translation or just NAT. Without NAT, only one computer could access the Internet and would be exactly what you would find if you connected the computer directly to the modem instead of the AirPort.
Anyway, all is working OK with the internet and wireless etc, playstation 3 connects to the PS network with an open NAT which is what I wanted, but I am worried I have no firewall or security?
Your AirPort's NAT service is one form of protection. The other is to enable wireless encryption (WEP, WPA, or WPA2) to prevent "uninvited guests" from accessing your wireless network ... and Internet connection.
Should the Airport extreme not be set to "distribute a range of ip addresses", it seems to be doing this anyways, who is giving out the ip addresses then?
No, you don't want to change the setting to "Distribute a range of IP addresses." This is intended for those unique situations where your ISP is providing you with one or more static IP addresses. This is typical with businesses, not consumers. In addition to NAT, your AirPort also provides another service: DHCP. This is how it provides IP addresses to clients on the local network.

Airport Extreme Base Station Dual Band MC340LL/A will not create a Wi-Fi network.

It will allow access to the internet only through the ethernet but not Wi-Fi. I downloaded the airport utility to set up the device and the yellow light keeps blinking. I use an ethernet DSL modem. This is the first Apple product i have bought and i got it off of Ebay as refurbished. Hopefully i don't have to return it because the router is the problem I don't know much else. Thx

FYI, i have reset the router many times with no new results.

AirPort Extreme Base Station and Windows Vista and Windows 7

I currently have a Belkin N+ Wireless Router and Belkin N+ USB Adapter Part # F5D8055. If I purchase the Airport Extreme Base Station dual band and replace my current router, will my current usb adapters connect and work with the apple extreme?

Yes.

Time capsule to extend airport extreme base station

I have an airport extreme base station dual band that I use to create a wireless network. I use a first generation time capsule single band to extend the wireless network. In the area of my home where the time capsule is my ipad and macbook the signal strength of the wifi is great and works great however my iphone 4 works horribly on wifi in the same room where the time capsule is located. Why is this? And is there a better configuration that would work better?

The AirPorts are all designed to try to extend the 5 GHz signal because that is the fastest connection. But, because 5 GHz signals are not as strong as 2.4 GHz signals, it's usually the 2.4 GHz network actually that winds up being extended because it's the stronger signal of the two bands and the extending device is usually located at some distance from the main router.
If your Time Capsule is extending the 5 GHz band, that's impressive. The AirPort Express would also probably extend the 5 GHz band if you placed it in the same area. Unfortunately, the iPhone cannot connect to that signal and must get it's connection from the main router. If you set things up so that the Time Capsule extends 2.4 GHz, then the iPad and your Mac will be running at significantly lower speeds.
It can be done by assigning a different name to the 5 GHz network and I can give you the steps. Is that what you want to do?
If you reversed the Time Capsule and AirPort Extreme, you'll have to set the Time Capsule up at 2.4 GHz and the AirPort Extreme will only extend 2.4 GHz. It cannot extend both 2.4 GHz and 5 GHz since it won't "see" that signal from the Time Capsule. No reason to do this really.

Airport extreme base station with Hp 3210 all in one printer

Just bought and hooked up the above. Using with iBook G4. Still dealing with dial-up unfortunately, but got online just fine. When I tried to print on the above, it immediately dialed up when I hit "print". ?? What's going on?

I have a pretty old HP all-in-one (G55) printer/scanner/copier device. Plugging it into my AEBS seems to not let me print to it. I have the most recent driver from HP.
Do you think it's my setup, or is the AEBS somehow not compatible with the older HP devices?
No the problem is with the HP driver.
Try using the HPIJS drivers.
For those with the older base station.
Use the process outlined here:
HP Printers (and others) not on compatibility list and Airport Extreme Printing
http://tech.ifelix.net/1300.html
Also, is it possible to fax, scan, etc through an all-in-one device plugged into an AEBS?
No, not via the USB port.
Can I scan using my all-in-one when it is connected to the USB port of an Airport Express or Airport Extreme Base Station?
http://discussions.apple.com/thread.jspa?messageID=610763&#610763

Airport Extreme Base Station with HP Printer problems

I have a pretty old HP all-in-one (G55) printer/scanner/copier device. Plugging it into my AEBS seems to not let me print to it. I have the most recent driver from HP.
Do you think it's my setup, or is the AEBS somehow not compatible with the older HP devices?
Also, is it possible to fax, scan, etc through an all-in-one device plugged into an AEBS?

I have a pretty old HP all-in-one (G55) printer/scanner/copier device. Plugging it into my AEBS seems to not let me print to it. I have the most recent driver from HP.
Do you think it's my setup, or is the AEBS somehow not compatible with the older HP devices?
No the problem is with the HP driver.
Try using the HPIJS drivers.
For those with the older base station.
Use the process outlined here:
HP Printers (and others) not on compatibility list and Airport Extreme Printing
http://tech.ifelix.net/1300.html
Also, is it possible to fax, scan, etc through an all-in-one device plugged into an AEBS?
No, not via the USB port.
Can I scan using my all-in-one when it is connected to the USB port of an Airport Express or Airport Extreme Base Station?
http://discussions.apple.com/thread.jspa?messageID=610763&#610763

Apple TV vs Apple AirPort Extreme Base Station (Simultaneous Dual-Band)

I have an original 40 GB TV that connects to my new ( (latest model)) Apple AirPort Extreme Base Station (Simultaneous Dual-Band) (MC340LL/A). Since upgrading to this new AEBS, my TV will not connect via its internal Airport card. The TV will "see" my "Home-LAN" but always gives the error message, "Connection Failed".
I have tried to Reset and Restore the TV, even the "Restore to Factory Defaults"! I have changed the security settings on my AEBS from an Open Network (no security) to WPA/WPA Personal, WPA Personal. I have changed the "Radio Mode" from "802.11a/n - 802.11b/g" to "802.11a - 802.11b/g". The TV will not connect! I now have it connected to my "Home_LAN" via Ethernet, and it works fine.
Anyone with a similar problem and a suggestion or solution? Do you think the internal Airport Card is the problem? Thanks

As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

Why does the new Dual-Band AirPort Extreme Base Station act as a proxy?

The previous thread
http://discussions.apple.com/thread.jspa?threadID=1531675
has been archived and nothing came of it, but after testing, I'm certain that their findings are true.
The Dual-Band AirPort Extreme Base Station (AEBS) with firmware 7.4.1 acts as a proxy for TCP ports 21, 554, and 7070 when NAT is turned on. This can be verified by using Nmap on any external server known to NOT have the ports open and having Nmap return that the ports are open. You can telnet to these ports to verify that they're "open," even though they are not on the server.
This functionality appears to be undocumented and as far as I can tell, the only way to turn it off is to put the AEBS into bridge mode and having some other device do NAT further upstream.
As a computer professional, this functionality extremely undesirable, particularly since it is not documented and doesn't have an "off switch." I wasted a bunch of time with one of my network engineers because of this, thinking that some network router was spoofing our server. I also wasted a bunch of my time trying to detect whatever "stealthy rootkit" had opened a FTP server and some other botnet related ports on our server, when in reality, it was simply my AEBS tricking me.
Disabling NAT-PMP ("Enable NAT port mapping protocol") does not affect this.
Is it too much to ask to have a checkbox in the "Advanced" section of the AirPort Utility to turn this feature off?

Welcome to the discussions forum Michael Bennett2.
Thanks for investigating this odd behavior.
If you want your work to be noticed by those who can effect change, you'll have to tell Apple via their feedback link. It won't do any good to post it here.
http://www.apple.com/feedback/

AirPort Extreme Base Station (New one) Dual band problem

Hey, I just got an AirPort Extreme Base Station, simultaneous dual-band today.
Anyone else having some problems with the 5GHz network? Seems my Transmit rate is very unstable. It changes between 7-54. It's 802.11n (5GHz) profile setting.
My 2.4GHz is staying at 54 (Since I set it for b/g).
As well, my MacBook Pro keeps connecting every time i update the airport base station, to the 2.4GHz one.

Welcome to the discussions, dwig365!
With a good connection, the Transmit Rate at 5 GHz should be in the 200-270 range. One of the perplexing issues with 5 GHz is that the much higher frequencies used in this band are absorbed by walls, ceilings and any obstructions much more quickly that 2.4 GHz signals. In other words, there is much less "power" with 5 GHz signals.
I've found that unless I almost have line-of-sight between the router and my laptop a few rooms away, the 2.4 GHz signal is stronger and more stable...hence faster. Taking it another step further, although it is not as "fast" as "n", "g" level signals penetrate and saturate much more effectively. It's a question of trade offs as in return for speed, you must give up penetration power.
It is not likely that you are encountering interference in the 5 GHz band, but it might help to experiment with some different channel settings. Make sure "use wide channels" is enabled under the options button on the Wireless page in AirPort Utility as well.

Mac Book pro can't connect to Internet through Apple airport extreme base station

I had problems connecting to the internet in the past with my macbook pro. One day it suddenly started working again but then I bought a second apple TV I lost connectivity. I have tried changing the IP address manually and while it shows me connected to the wifi I am still with out internet. When I hooked up the new Apple TV that I bought it booted my computer from it's ip address. The apple TV though wouldn't work and now nor would my computer. I ended up setting the Apple TV's ip address manually and now it works fine. My computer on the other hand does not no matter if I set it manually or not. Even if I plug in the ethernet cable from the base station it doesn't work. It show that it has a self assigned IP address. After I set it manually it shows that I am connected both via wifi and the ethernet cable but I can't connect to the internet. If I plug the modem directly into the computer bypassing the base station I get internet and it is using the IP address that worked originally.
It has something to do with the connection from the base station to my computer but this is odd considering every other device I have: iPhone 4, apple tv, apple tv, apple mini with retina display all work perfectly via wifi (newest apple tv had to be set manually as I stated above but now works fine). When I check the ip of the base station itself it seems to be different from the ip of the computer when the computer was connected directly to the router. I don't understand why my computer now can't connect to the internet via the base station whether it be wifi or by ethernet. Can you please help me trouble shoot this?
I have an AirPort Extreme base station which allows up to 50 users and a 30 meg connection speed.
I have a MacBook Pro (17-inch Early 2009), OS X Mavericks (10.9.2)

It has something to do with the connection from the base station to my computer
I don't think so..
I just posted a reply which totally vanished.. strange strange website now.
Please post some screenshots of your AE setup from the airport utility.. I want to see the summary page, then the network and internet tab.
Please tell us what modem you use.. is it a router??
If you have satellite or 3G wimax etc service they often are limited to 5 IP addresses... the AE takes one and then 4 more devices can join .. no more.
You need to also give us the screenshot of the IP you are getting in a computer that works.
EDIT
Sorry this is half double post.. the previous page refused to display.. now it has returned..

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

Hi I'm from Australia.
If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?

Any specific recommendations for a standalone ADSL modem though?
Always a good idea to use the modem that your service provider supplies or recommends....often free....since you know that it will be supported in the event of connection difficulties.
I have made the mistake of choosing the "best" modem based on test reports....only to find out later that the ISP would not offer any support when I was having connection difficulties.
The ISP blamed the modem. The modem support folks blamed the ISP.

I have an Apple AirPort Extreme Base Station (Simultanious Dual_Band) (MC340LL/A), and updated the software. After updating no devices can connect via wifi. Any suggestions.

I have an Appl,e AirPort Extreme Base Station (Simultaneous Dual_Band( MC340LL/A. After updating the software, no devices can connect via wifi.

As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

AirPort Extreme Base Station (Dual Band) vs Apple TV

Similar Messages

Maybe you are looking for