AirPort Extreme Base Station is not Available in AirPort Admin Utility

I don't see my APEX Base Station in the list in AirPort Admin Util. I can configure by opening by IP. I have no software firewall. I have plugged in directly to base station, and have reflash with 5.7 firmware. I am using 4.2 of AirPort Admin. I've Tried everything I can find in forums. Anyone else have issues?
I'm using Mac OS 10.4.4

I have tried resetting it. It doesn't always work. Sometimes the base station is listed, and sometimes it is not. The base station is functioning though. I can access the newtork, It just doesn't show up in Admin Util.
I also have an AP Epress connected to AP Extreme via WDS. From the wired side, they either both show up or both do not, which is expected. When they don't show up on the Admin list, the Express also doesn't show up in iTunes from the wired side. Wireless clients don't seem to exhibit this problem.

Similar Messages

HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
Is there a way to resolve this issue?

How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

Once you have the drive connected to your Mac, click System Preferences (gear icon) on the dock
Click Time Machine
Click Options
Be default, the hard drive will be Excluded from backups. Click the drive to highlight it, then click the "-" (minus) button at the bottom of the list to remove the drive from Excluded items.
The drive will be backed up on the next Time Machine pass
Everything above assumes that the hard drive has been formatted in Mac OS Extended (Journaled) as Time Machine will only backup drives in that format.

Airport Extreme Base station does not 'see' Airport w/Airtunes. HELP!

I just purchased and installed an Airport Extreme Base startion (802.11n), and it does not 'see' my Airport Extreme with Airtunes. I have already tried re-setting the Airport + Airtunes to the factory settings, but since I installed the new Base station software, I no longer have the Airport Express Sett up assisstant?!?
What am I doing wrong?

Your Mac won't be able to communicate with your Airport Express until you reconfigure your Airport Express to join the wireless network now being created by your new Airport Base Station.
The "Airport Setup Assistant" has been replaced by the "Airport Utility". You can find that new utility installed in your Mac's Applications->Utilities folder.
What you should do now:
1. do an factory default reset of your Airport Express.
2. plug the Airport Express (temporarily) into power in the same room as your Base Station and your Mac.
3. on your Mac, run the Airport Utility. It should "see" your Airport Express. Click on the Airport Express icon, click to continue (your Mac will switch wireless networks temporarily), click Continue, and follow the instructions for configuring the Airport Express so that it "joins" the existing wireless network created by your Base Station.

Airport Extreme Base Station is not picked up by my Mac Bok Pro

I purchased a Airport Extreme Station, set it up, and everything worked fine.
We had a power outage and since then neither my Macbook Pro nor my other laptop sees the base station. I hard reset the unit, still no response. I hooked up the the base station to my Macbook Pro with the straight-through ethernet cable and yes there it was.
After I unplugged the cable, the airport could not locate the base station again. I have the latest firmware upgrade and Airport software upgrade.
I am running out of options and ideas - any help?
Message was edited by: marbmarc

Perhaps try downloading the latest update and reload it into the Extreme. It is possible that something was corrupted during the power outage that is causing things to be a little bonkers. Use the Search in the top right of this window and look for "Airport Extreme Firmware". You may have to dig a little bit to find the most current but its there. Download it and install while connected via ethernet.

Airport Extreme base station does not appear in Airport Utility

I cannot see the basestation that I am connected to via WIFI or Ethernet. I cannot see the basestation on ipad or iphone app either. Basestation is working fine and i have connection working fine with a green light but cannot configure the basestation to allow guest networks or connect my external storage drive.
any suggestions will be appreciated.

OK. That should be a third or fourth generation Extreme, plenty new enough. (The most recent OS X and iOS versions of AirPort Utility cannot configure the original Extremes, but they can handle my mid-2007 second generation Extreme.)
If two or three devices on the same network as the Extreme cannot "see" the configuration interface, I would guess that the problem lies in the Extreme itself.
Have you tried power cycling the Extreme?
Did you purchase AppleCare for your 2011 MBP? If so, and if you bought the Extreme less than two years earlier, the AppleCare should cover the Extreme also.

HT3500 I am trying to hook up my new Canon MG5320 printer wirelessly to my MacBookPro with OSX.8.2. The Airport Extreme Base Station does not have a WPS button and so I seem to be stymied even though the printer detects the Airport Extreme. Suggestions?

I am trying to set up my new Canon MG5320 printer to my wireless network. However, there is no button on the Airport Extreme to push when I get to that step in the set-up directions. I am using OSX.8.2. Suggestions please!

If the display shows the "Press and hold the WPS button..." message on the MG display, press the red Stop button on the MG and then select Standard Setup. The MG will search for networks and should display your Airport Extreme's network name. Select this and then enter the password to connect to this network.

Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
Thanks

The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
Assuming your AE is gen3 or greater.
You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
If your AE is G wireless or earlier model.. really the time has come for replacement.
If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

Certain web address not available when using Airport Extreme Base Station

Hello. To access my "secure" account at the local library, I must use a web address that contains a colon followed by a number. I believe that this is a port number, but I confess that all the discussions here regarding ports are going well over my head, and I may be incorrect with this assumption.
My problem is that while I CAN access this site by connecting to my DSL router directly via ethernet cable from my iMac G5, I cannot access the site when connecting to the internet in the mode: iMac Airport to Airport Extreme Base Station to DSL router via ethernet.
The format of the web address is: http://xxxx.yyyy.net:####/zzzzz/, where #### is the number I guess may be specifying a port and causing my problem.
Can anyone advise me, in simple terms, how to get to this address when in the Airport--internet connection mode? Will the solution have any adverse side effects?
Regards and Thanks
iMac G5, 2.5 year old AEBS Mac OS X (10.3.9) Westell 327W 4-port DSL Modem, not using wireless feature.

Very likely the embedded firewall that comes with your AirPort blocks the port you are trying to use.
In order to solve this, best way is to modify the AirPort settings (open the AirPort maintenance app):
Click at the tab "port forwarding" and add the desired port as "public port" to the list. "private IP" is the IP of your Mac and for "private port" type in the port number again.
If you are unsure about the IP of your Mac, look at the network maintenance application.
Well, one side-effect is that you have an open port in your configuration which could cause security issues... but only if you are paranoid So there is nothing to care about (note that without the AirPort inbetween your Mac and your modem, this port would be not blocked and freely accessible

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
Power off the AirPort by pulling the power cord
Wait a minute or two
Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
Release the reset button and allow a full minute for the AirPort to restart
Now try to configure the AirPort again. If you continue to see the same symptoms as before, the AirPort will need to be replaced.

AirPort Extreme Base Station with Modem not recognized by airport utililty,

My Apple M8799LL/A AirPort Extreme Base Station with Modem and Antenna Port is no longer recognized by the airport setup utility, nor will it allow internet connection. Has worked fine until last weekend when I did a full disk utility on all of my drives. Now I get a message, none of your trusted networks are available would I like to join (my network name)? Airport looks fine, can connect locally, lights up as usual.
How can I make it trusted again and get dial up internet to work again?

resetting has worked for months with no return of the problem.

HT1218 Airport Extreme base station is working, but not visible on network?

My Airport Extreme base station is working: all devices are able to connect to the internet, but Airport Utility shows no connection. Only one computer even shows the device-- greyed out-- saying "Device not Found." The airport utility shows version 6.2; OS X version 10.8.3. How do I update the base station to version 7 if the device can't be found? And how do the devices connect to the internet without "seeing" the device?

Thanks for checking. This model should be visible in AirPort Utility in Mountain Lion.
If you have not already done so, I suggest that you perform a complete power cycle on the entire network as folllows:
Power off every network device....in any order you want
Wait a minute or two
Start the modem first, and let it run a few minutes by itself
Start the AirPort Extreme next, the same way
Continue starting devices one at a time about a minute apart until everything is powered back up
Check the network again using AirPort Utility
You can also temporarily connect an Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Extreme to see if a connection is established that way.
If still no luck, try another Mac if you one handy. After that, all that I can suggest is that you perform a Factory Default Reset on the AirPort Extreme and configure it again.

Airport Utility does not see Airport Extreme Base Station

Purchased Airport Extreme yesterday at Apple Store to replace old Netgear Router. Wanted wireless network to work with 2 identical HP Laptops running XP with SP3 and 2 iPod touches, and possible future purchases of iPad 2 and Apple TV. Installed Airport Utility software from CD on Dell Studio running Windows 7. Connected Airport Extreme to cable modem and Dell Studio. Ran Airport Utility software to configure Base Station but it did not recognize the Base Station. Base Station had blinking amber light. Did have internet connectivity on Dell Studio, and wireless internet connectivity on 2 iPod touches, and on one HP Laptop. No wireless internet on other HP Laptop. But wireless internet connection was unsecured and Airport Utility did not see Airport Extreme so could not configure it to make it secure. Contacted Apple Customer support. After 30-40 minutes of attempting several different possible fixes only able to use Airport Utility to configure Airport Extreme remotely, wirelessly, from one HP Laptop, not the Dell Studio that is directly connected to the base station. Now that the base station is configured the network is secure. However, second HP Laptop cannot connect to primary wireless network. I created password protected "Guest" network using Airport Utility, and laptop is able to connect to this Guest network. From reviewing forums am now able to configure Airport Extreme with Airport Utility by using "Configure other" on Dell computer. But utility cannot find device by scanning. Would like to find way to (1) have Airport Utility on Windows 7 Dell see Airport Extreme by scanning and not using "configure other," and (2) have 2nd HP Laptop connect to primary network and not "guest' network. Any assistance would be greatly appreciated. Thanks.

Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
Any help would be greatly appreciated.

Macbook does not see airport extreme base station

Hi
I set up my airport extreme several years ago. I recently noticed that, under "security," the guest network says "WPA2 secured," but the main network says "none." Is this a problem; i.e., does the main network lack security? Further, when I open the airport utility, it cannot find a base station.
What am I doing wrong?
Thank you!
ron

Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
Any help would be greatly appreciated.

Airport extreme base station detecting someone elses network but not mine.

Sorry if this subject has already been discussed but I couldn't see it anywhere.
I have an airport extreme base station set up and it works fine but this morning i noticed that I had very little signal which has never happened before so upon further investigation I noticed that my computer was hooked up to a Netgear network amd not my own usual airport "home" network.
I got my own network back again and my signal is now full strength. The worrying thing is that my computer couldn't seem to find my airport "home" network when I searched for it. I had to start again from scratch and reset it.
Is there a way I can tell my computer to use only my airport network and no other? Someone obviously has an open network nearby.
Message was edited by: lispiers

Try the steps indicated in Mac OS X 10.4 Help: Choosing preferred AirPort networks.

AirPort Extreme Base Station is not Available in AirPort Admin Utility

Similar Messages

Maybe you are looking for