Airport Extreme base station no longer playing nice with Mac Pro

This is a strange problem...
I have an Airport Extreme base station (purchased in 2004) that I use with verizon DSL to get a wireless network going in my house, and I connect three computers wirelessly.
I have an ipod touch and toshiba PC laptop that are both able to connect to the network and run just fine. But lately (past 2 weeks or so) when I try to connect with my MacPro desktop I can go to a few sites, but after a few minutes the airport locks up. At that point none of my computers will connect and I have to unplug and then replug the airport. At that point the network will start up again and if I do not try to get on with Mac Pro then things run fine, but when I try to connect with desktop again, after another few minutes the same thing happens.
I know the problem is with the airport and my Mac Pro - I have done numerous connection experiments and have narrowed the problem down to that.
Is it possible that my MacPro might be drawing more power and causing the airport to overheat? (it is rather hot in the room with DSL connection)
Or should I accept that the current base it old, and bite the bullet and get a new base?
Any thoughts?

Could you post what you did in order to resolve the issue. I'm having a problem with the base station in that I cannot connect to the internet with my laptops (a mac and pc) while I can connect wirelessly to my network with my desktop (G4). The base station is not detected in the base statin admin utility or the aiport setup utility. If anyone else has a solution I would be much obliged to read it.
Thanks!

Similar Messages

  • Is my AirPort Extreme base station A1034 (802.11g) compatible with Comcast 50 Mbps internet service?

    Is my AirPort Extreme base station A1034 (802.11g) compatible with Comcast 50 Mbps internet service?

    The WAN port on the A1034 will handle up to a 100 Mbps Internet connection, so you are OK there.
    Wireless on the A1034 is limited to 54 Mbps tops, so things should work OK as long as wireless devices can receive a strong wireless signal from the Apple router.

  • Airport extreme base station no longer recognizes password

    Away from house for a week. Came back and none of our iPhones, iPads can connect to wifi network. Airport Extreme base station will no recognize my network password to check settings. Airport Epress will not join network either.

    Hi danny_A1A!
    I have a couple of articles here that should be able to help you troubleshoot this issue. The first is a quick assist article pertaining to Wi-Fi issues and can be found here:
    Wi-Fi Quick Assist
    http://support.apple.com/kb/ht1145
    We also have another article on troubleshooting Wi-Fi connectivity, and it can be found here:
    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    http://support.apple.com/kb/HT4628
    Take care, and thanks for visiting the Apple Support Communities.
    -Braden

  • Older airport extreme base station as a network extender with new time capsule

    I just bought a new time capsule (802.11ac). Can my older airport extreme base station (model A1143) be used as a network extender with it?

    Yes, although it maybe disappointing..
    There are two kinds of extending.. wireless repeater type which is poorest as it has to transfer all packets in two steps instead of one.. hence will halve the speed.
    Or using ethernet to the old extreme and set it in bridge.. You can then setup roaming network... this is much better.. but getting ethernet to the right place could be messy or expensive or both.
    http://support.apple.com/kb/HT4260
    wireless extend doco.. mind all of this is out of date.. the basics are correct.. the methods via the airport utility may be obsolete.
    http://support.apple.com/kb/HT4145
    Documentation has rather lagged lately.

  • About Apple AirPort Extreme Base Station?

    I Need A Wireless Router & i'm looking for Apple AirPort Extreme Base Station cause I Need a Wireless Router cause I Have at Home a Sony DVD Wireless Blue-Ray Player & i'm trying to Connect to The Internet on The Device but it's not letting me cause it say's I Have No Wireless Router to Connect to or Something? but I Connected The Sony DVD Blue-Ray Player to My 15inch Coby L.E.D LEDTV1526 HDTV & it Play's Blue-Ray Movies Excellent  it just I Cannot Connect to The Internet on there cause I Need a Wireless Router & I Wanted to know if Apple AirPort Extreme Base Station is The Right Wireless Router for Me? cause I Like Apple & I Would like to Get The Apple AirPort Extreme Base Station if it's ok with what I Need it for? I Never had a Wireless Router before, I Love Sony & I Love Apple they both have Great Products on My Sony DVD Wireless Blue-Ray Player I Can Stream Movies From The Internet & I Wanna do that let me know if Apple AirPort Extreme Base Station is ok for me Please?
    in My Bed Room I Have My 15inch Coby L.E.D LEDTV1526 HDTV & I Have My Optimum Cable HDTV DVR Cable HDTV Ready Connected & My Sony DVD Blue-Ray Player Connected to My 15inch Coby L.E.D LEDTV1526 HDTV But I Need a Wireless Router & is Apple AirPort Extreme Base Station right for me? all I Need now is Apple TV Next then i'm really Loaded Up.
    in My Home I Have Optimum Triple Play Package Deal, I Have Cable HDTV Silver Package with Optimum DVR & Optimum Online Boost Plus for Internet & I Have My Regular Optimum Phone Service all 3 from Cablevision in My Bed Room & I Have over 2000+ DVD Movies & Music CD's & on Apple iTunes I Have almost 1000 Music & Music Video's & Almost 1000 App's for My Apple iPhone 4 32GB & Future Apple iPod Touch 64GB & I Have 32 Movies on Apple iTunes & 4 TV Shows on Apple iTunes & I Have 70 Mac App Store Mac App's from The Mac App Store
    & in My Bed Room I Have My 2009 Apple 24inch iMac Computer & My Canon PIXMA MP480 All-One Photo Printer & My Apple Mouse & Apple Keyboard & My G-Technology G-Drive 1TB Drive & My Canon Powershot A2100 IS Digital Camera & My Apple iPhone 4 32GB From Verizon Wireless Connected To My 2009 24inch Apple iMac Computer so I Have lots of things going on in my Room. so have a Very Merry Christmas & Happy Holiday's & Happy New Year
    If Someone did not like the way I Made this Thread i'm Very Sorry I Did it in the wrong way, I'm Sorry & I Won't do it if it was the wrong way i did it? & i'm sorry I Made the Mistake & I Just thought i would get Help on the Apple AirPort Extreme Base Station I Needed help with & I'm Sorry what i did if You did not like it, I Have not been on here often & I Only come here if I Need help with something so maybe you could let this thread slide but if not? then it's ok & i'm still Sorry I Made it & I Did not mean to make it in a bad way if thats what you thought? so have a Very Merry Christmas & Happy New Year & Happy Holiday's from your Online Friend & Costumer Byron.
    Peace.

    Ok after Christmas was Over I Went to PC Richard & Son & was looking for an HDMI Cable & I Found it so then I Asked them about My Sony DVD Blu-Ray Player & told them about the situation that I can stream Movies from the Internet to The Sony DVD Blu-Ray Player & then I also talked to them about a Router so after that they had Showed me The BELKIN Share N300 Wireless N' Router & they said this is The Cheapest 1 & it was $29.99 plus tax, they said that I Can Connect that to My Sony DVD Blu-Ray Player to The BELKIN Share N300 Wireless N' Router & Connect The Belkin Share N300 Wireless N' Router to My Cable Optimum Online Modem then Connect The Wire from The Optimum Cable Modem to My Computer so now My Sony DVD Blu-Ray Player can Stream Movies from The Internet & also I Have everything Conected & working great & I also have Netflix on My Sony DVD Blu-Ray Player & I Can also watch Movies on Netflix on My 24inch iMac Computer to, everything is working fine so now 1 Very Last Question & i'll leave you alone
    if I Were to Buy Apple TV Can I Get a Wireless Home Networking Connection on The BELKIN Share N300 Wireless N' Router? or is it only can Work on an Apple Airport Extreme Base Station?
    I Hope you had a Happy New Year ok take care from Byron.

  • Configure TC and Airport Extreme Base Stations with different channels

    I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap.  I thought I would post my results here since I didnt' find a good article online.
    Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup. 
    Setup is a 3 flloor house where the 3 wired network locations have wireless overlap.  The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel.  In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
    Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels.  I am writing this from memory, so feel free to ask questions and I will track this topic:
    Procedure
    Setup time capsule as your base station.  Do all the setup for your wireless and guest networks.  Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
    Plug your first airport extreme/access point into your wired network.  Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
    Use the airport utility to first configure it to "extend" your wired network. 
    Then, go in and reconfigure it manually in the airport utility.  Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
    Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137). 
    Now go to the top tab and click on the "internet" icon
    Go to the DHCP tab and change it to "bridge mode."  This will tell the AE to not give out IP addresses (the TC will do this for you).  If you get an error that the IP ranges conflict, you have not done this
    Note that if you have a guest network setup, you will need to set this up on the AE as well. 
    Now test your airport setup.  Take your client (macbook, iOS device) and connect to your network.  Move to a spot near the TC and pull up a web page.  Keep an eye on the signal strength and beginv moving toward the AE.  Refresh the page as you move around.  You should at some point see the signal strength increase.  Refresh your page again.  You should be now connected to to the AE.  I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
    Another test you can do is to start backing up on your TC and then test the move.  The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
    If you need to setup another AE, simply follow setups 3-10.
    I hope this helps others.  I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products. 

    I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap.  I thought I would post my results here since I didnt' find a good article online.
    Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup. 
    Setup is a 3 flloor house where the 3 wired network locations have wireless overlap.  The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel.  In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
    Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels.  I am writing this from memory, so feel free to ask questions and I will track this topic:
    Procedure
    Setup time capsule as your base station.  Do all the setup for your wireless and guest networks.  Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
    Plug your first airport extreme/access point into your wired network.  Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
    Use the airport utility to first configure it to "extend" your wired network. 
    Then, go in and reconfigure it manually in the airport utility.  Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
    Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137). 
    Now go to the top tab and click on the "internet" icon
    Go to the DHCP tab and change it to "bridge mode."  This will tell the AE to not give out IP addresses (the TC will do this for you).  If you get an error that the IP ranges conflict, you have not done this
    Note that if you have a guest network setup, you will need to set this up on the AE as well. 
    Now test your airport setup.  Take your client (macbook, iOS device) and connect to your network.  Move to a spot near the TC and pull up a web page.  Keep an eye on the signal strength and beginv moving toward the AE.  Refresh the page as you move around.  You should at some point see the signal strength increase.  Refresh your page again.  You should be now connected to to the AE.  I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
    Another test you can do is to start backing up on your TC and then test the move.  The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
    If you need to setup another AE, simply follow setups 3-10.
    I hope this helps others.  I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products. 

  • Airport Extreme Base Station and Win 2000

    I have a new Airport Extreme Base Station. All is well with my Mac but my company laptop uses Windows 2000 Pro. The software that came with my AEBS will not install I get an error that I can not install as Win XP SP2 is required. Anyone got a work around or know where I can find compatable software?

    All,
    I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
    I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
    My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
    The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
    I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes?

  • Purchase of new Airport Extreme Base station??

    have i wasted money on purchase of NEW Airport Extreme base station? i have fios with actiontec router and tv service.  the Guest network does not work nor does Actiontec have ability to provide guest network. I am about to return the AEBS as I dont see any reason to keep it other than the 2.4 and 5GHZ network ability.  Oh yeah, the 802.11 ac too.

    Find a way to disable DHCP on your Actiontec router, making it a modem. Call Verizon and ask them for instructions: "I have my own router, and want to disable the Actiontec's router. How do I do that?"
    Here is one such question, from Verizon's support forum: http://forums.verizon.com/t5/FiOS-Internet/Disable-Actiontech-DHCP/m-p/281653#M1 9622 Try that.
    The AirPort Extreme can be configured as a bridge, i.e. not performing any router function, but you will be losing most of its advantages by doing so.
    Guest Network must be created by your router.

  • Airport utility no longer recognizes my Airport Extreme Base Station, which had been set up to extend a wifi network

    Hi.  In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds.  Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended.  I folllowed all the directions from the apple support pages, and finally got it to work.  I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension.  Then a week or so ago I noticed that my laptop would no longer connect to my base station.  I did not have time to look into it until this week.  Airport utility, either on my Mac or iphone no longer recognizes my base station.  My mac is running OS X 10.10.1  and my iPhone is running iOS 8.1.2  I have tried both hard, soft and factory resets of my base station to no avail.  The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before.  I can't actually connect to it, but it does try.  Then after approximately 5 minutes, it disappears from my list.
    Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c?  airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software.  I am attaching an image of that.
    Thank you,
    John
      Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?

    I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
    Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
    Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
    Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
    Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
    Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature.

  • HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
    Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
    As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
    Is there a way to resolve this issue?

  • Why can I no longer print from my Windows XP computers to my Bonjour connected Canon printer thru an Airport Extreme Base Station (f/w 7.6.4, model A1301)?

    Something has changed recently and I haven't figured it out.  My 2 Windows XP computers are no longer able to print via Bonjour.  I have tried removing and reinstalling Bonjour.  Upgrading the firmware on the AIrport Extreme Base Station and comparing Port settings from an able to print Windows Vista laptop.  Port settings match and Bonjour says it sees the printer...but the communication is not happening between the computer and the networked printer, it times out and produces an error in the print que.  Both XP computers have no problem using the internet via the Base Station.  One is wired and one is wireless.  Thoughts?

    Sounds a bit like a problem being discussed in this thread:
    http://discussions.apple.com/thread.jspa?threadID=2651093&tstart=0
    I suspect some kind of update is at fault. Like you, my printer/base station setup had been working fine until recently.

  • Solution to Airport Extreme Base Station + Airport Express networking probs

    I've been investigating this for 3 straight days after inadvertently destabilizing my network. There are tons of posts discussing a variety of issues, all of which seem related. My goal here is to provide links to other relevant posts and explain what I ended up doing to get things to work.
    First, the background. You can skip below to SOLUTION if you don't really care... However, I highly recommend you take the time to read everything, as you'll get other useful information in the BACKGROUND section. I'm guessing many of you have similar, related problems so BACKGROUND might help provide context (and solutions) to some things you are seeing...
    MY SETUP:
    AirPort Extreme Base Station (AEBS) of type b/g (round one, not square one), connects to the cable modem, and creates a WDS network that is then shared across two standard AirPort Express (AEX) units (100megabit, not the gigabit ones). One AEX serves as a relay unit that accepts clients, the other serves as a remote unit that also accepts clients. The intent is to show a single network throughout the house and let users log on to one network and move between networking units without having to switch from network to network.
    I have a variety of networked devices throughout the house all running on the same network (2 Mac Pros, a Powerbook G4, a Mac Mini, an Apple TV, a Windows XP laptop, two iPhones, two wifi printers, and a 5-unit Sonos system, plus the AEBS and two AEXs). Yeah, I'm a geek.
    The Mac Pros are both running 10.4.11, and the Powerbook is running 10.5.2.
    AEBS is running firmware 5.7
    AEXs are running firmware 6.3
    All Macs were initially accessing configs via the recently released AirPort Utility 5.3.1. More on that later.
    BACKGROUND:
    I've had this network setup working for about a year now. Recently, I've been having poor network performance problems and came to the conclusion it was a LAN problem (ie. problem with my home network, as opposed to with my ISP). Upon initial investigation, I began by looking at my networking logs (via AirPort Utility 5.3.1). You get to those by selecting the unit in question, choosing "Manual Configuration", the selecting the "Advanced" tab up top with the "Logging and SNMP" sub-tab. Click the "Logs and Statistics" button therein for log details from that unit.
    The first thing I noticed was "Administrative access denied to ff80::xxxxxxxxx" messages - a lot of them. I didn't recognize the ff80:: address in question, and so became concerned it was someone outside the network trying to hack one (or all) of the AEBS/AEX units. You can see threads discussing that investigation here:
    "Hack or panic?" - http://discussions.apple.com/thread.jspa?threadID=1438486
    "Administrative access denied" - http://discussions.apple.com/thread.jspa?threadID=1438865
    Long and short of it is that the recent AirPort Utility 5.3.1 release (current as of March 13) seems to have problems (keychain) when attempting to access the AEBS and AEX units. The "Administrative access denied" logs actually refer to the client machine you are using when you try to read the logs. The ff80::xxxxxx address is simply the IPv6 address for the machine you are using; if you turn off IPv6 on your client machine, that address should switch over to begin showing a regular IP address instead (something like 10.0.1.xxx), which makes it easier to associate the IP to the machine. I explain how to deactivate IPv6 on both Tiger (10.4.x) and Leopard (1.5.x) here:
    http://discussions.apple.com/thread.jspa?messageID=6814978#6814978
    Anyway, in the process of investigating the "Administrative access denied" problem, I began tinkering with my AEX settings. Specifically, I ended up performing a hard factory reset (unplug unit, plug back in while holding down the little button with paper click/pen for ~10-15 seconds until light flashes green 4x then reverts to amber/yellow/orange). I began reconfiguring my entire WDS network using the newly updated AirPort Utility 5.3.1, and that's when the trouble started.
    (If you are having problems seeing either your AirPort Extreme Base Station or AirPort Express, read this:)
    In short, each time I thought I had properly configured things and then confirmed settings (kicking off a reboot on the AEX unit) the unit would restart with new settings but not properly join the WDS and not show up in the AirPort Utility list of units. More specifically, I would start with a "wiped" AEX and see both the AEBS and the AEX in my AirPort Utility list, but upon confirm/reboot the AEX would disappear and the AEBS would remain. However, that's not 100% correct. It seems that sometimes I would end up with the AEX and NOT the AEBS. Because both the AEX and AEBS were theoretically "hosting" the same network name (remember, WDS shares the network name across units) my auto-login feature for my client computer's wifi seemed to "jump on" whichever unit it first saw hosting the default network name for my house. In other words, it seems what was really happening was that I was ending up with two separate networks in my house, both with the same name but not talking to each other (as opposed to two units sharing the same network name and internet connection). The AEX would continue to blink orange/amber/yellow (whichever color it is to your eyes ) because it could not grab an internet connection -- and if I was on the network through that AEX unit I would not get internet. But if i was connected through the AEBS I would continue to have internet access. As far as my client computer (my Mac Pro) was concerned, I was on the home wifi network even if I was on the AEX rather than the AEBS -- it would show the home wifi network name as the name of the network it had connected to. But when I opened the AirPort Utility 5.3.1 I would see only the AEX (if I was connected through it) or the AEBS (if connected through it) -- a clear indication that the units were not truly sharing the same network.
    I tried rebooting and reconfiguring the AEBS and AEX about 50 times (literally). I even tracked down an older version of the AirPort Utility 5.2.1 via this thread (see Tesserax post):
    http://discussions.apple.com/thread.jspa?threadID=1067565
    One interesting thing re: 5.2.1 is that the "Administrative access denied" errors summarized above disappeared. As explained in a post reference above, the going theory is that this a permissions/keychain problem new and unique to AirPort Utility 5.3.1. However, even though 5.2.1 does have a slightly different interface with different settings, I still couldn't get the WDS to work.
    EVENTUALLY, I came across this post:
    http://discussions.apple.com/thread.jspa?threadID=1422527
    MuaddibOfArrakis walks through setting up a WDS from scratch, and the workflow is different than what is possible with either AirPort Utility 5.3.1 or 5.2.1. He's doing it with the old version of AirPort Admin Utility, which I fortunately saved a copy of many moons ago when I had somewhat-related problems with my WDS (since forgotten). In fact, it's a lot easier. What's nice about this older app is that it literally does the heavy lifting of "connecting" the AEBS and AEX units during the configuration -- it reboots both at the same time as the config is happening, and lets you choose from a list of available units to "add" to your WDS network. In short, it's a FAR SUPERIOR workflow even though some of the GUI isn't as intuitive as the newer AirPort Utilities that were designed to replace it.
    SOLUTION:
    If still have a copy of the AirPort Admin Utility follow the instructions from MuaddibOfArrakis here:
    http://discussions.apple.com/thread.jspa?threadID=1422527
    If not, try setting up your WDS network using AirPort Utility (hereafter AU), with these configs (take from my now-working network), as viewed through AirPort Utility 5.3.1.
    I. Configure your AEBS.
    Select the AEBS from AU, and choose "Manual Setup"
    1. Under the AirPort tab up top:
    a. Under "Base Station" sub-tab:
    i.) assign a name for that specific unit, so you can later identify the specific unit from the list of units -- this is the name that will show up beside the unit in the AU list of configurable units. You can name it something like "kitchen", or "office". I have mine numbered, so XXXXXv1, XXXXXv2 etc where the XXXXX is the name of the shared network and the numbers help me tell the units apart. Just be sure you name each uniquely, and if you have several you might write the name on the unit itself.
    ii.) pick a password for logging into that unit. This is different from the network password, its a security check to get in and change the configs on this unit later. Be sure to remember it in your keychain for the sake of simplicity, and write it down somewhere secure.
    iii.) if you choose to set time automatically, pick a location that you will use consistently across all your units. I use time.apple.com.
    iv.) uncheck "Allow configuration over Ethernet WAN port" unless you want to be able to remotely mess with settings -- which you almost certainly do not need to do.
    v.) I left the "Options" button alone - no settings there.
    b. Under the "Wireless" sub-tab:
    i.) Wireless Mode: "Participate in a WDS network"
    ii.) Network Name: this will be the name of your wifi network shared by all units, so be sure to remember what you pick. If you are already connected to this AEBS via wifi while you are making these changes, then you can use the same wifi name you already have set up -- you don't have to change it. Note that if you DO change it, after reboot your will LOSE connection to the network and have to reset your wifi settings on your client machine to match the new network/password in order to be able to access the network.
    iii.) pick a Radio Mode. I'm using b/g compatible. You'll want to do the same, unless you are on the new gigabit AEX. I'm pretty sure about this, but not 100% -- others post if I'm wrong.
    iv.) choose a Channel. This can be a more complicated procedure, but for now just pick something consistent across all your units. If you get everything working and find that you're having intermittent network problems, you could later try changing your Channel -- it can pick up interference from phones, microwaves, etc and changing it can help.
    v.) I have wireless security set to WPA/WPA2 Personal.
    vi.) Wireless Password is the password for access to your wifi network (not your unit itself). If you are connecting to your AEBS via wifi while doing this config, then you can use the same password you have already set up. Pick a good one unless you want other folks jumping on your wifi and stealing your bandwidth and/or credit card numbers . Remember it in your keychain and write it down someplace secure, because you'll need it for the other units too. As noted above, note that if you DO change it, after reboot your will LOSE connection to the network and have to reset your wifi settings on your client machine to match the new network/password in order to be able to access the network.
    vii.) Click the "Wireless Options" button. I have my multicast rate set to 2mbps, transmit at 100%, timeout at 1 hour, and i have checked the "Create a closed network". This last step keeps your network from advertising itself to the outside world. Users can only find it by explicitly typing the network name into their wifi settings (e.g. AirPort -> Other... then enter Network Name, Security and Password). I leave interference robustness unchecked.
    c. Under the "WDS" sub-tab:
    i.) the AEBS should have it's WDS Mode set to "WDS main".
    ii.) Check the "allow wireless clients" box on the AEBS; this lets you connect client machines to it directly too.
    iii.) hit the plus button to add the Remote system (AEX). There are two types of configs for the AEX's - "remote" and "relay". Assuming you have 3 units like me (2 AEX and 1 AEBS) the key question is whether you will place each AEX within direct reach of the AEBS (remotes), or if you will have one AEX in the middle connecting to an AEBS on one side and an AEX on the other -- where the furthest AEX is out of reach from the AEBS (remote) and connects only to the AEX in the middle (relay). I'm using a relay setup. If you are using relay, you can still set up the AEX relay to serve client computers too -- it doesnt have to JUST relay. More on that later. For now, you want to add only AEX units that will talk DIRECTLY to the AEBS. So if you have a setup like mine, just add one (the one in the middle - the relay). If you have two remotes connecting directly to the AEBS, you will add them both here. When you hit the '+' button it will ask for both an ID and description. For description I use the name I'm assigning to each unique unit (as above, "kitchen" or XXXXXv1 or whatever you use). For AirPort ID, use the number listed on the AEX unit itself (not the number for "Ethernet", also on the AEX unit).
    d. Under the "Access" sub-tab:
    i.) I have it set to "Not Enabled". I'd suggest you start that way too, and you can go change it later if you get everything working correctly.
    2. Under the "Internet" tab up top:
    a. Under the "Internet Connection" sub-tab:
    i.) Connect Using: Ethernet
    ii.) Configure IPv4: Using DHCP
    iii.) Ethernet WAN Port: Automatic (Default)
    iv.) Connection Sharing: Share a public IP address
    b. Under the "DHCP" sub-tab:
    i.) DHCP Beginning Address: 10.0 . 1 . 2
    ii.) DHCP Ending Address: 10.0.1.200
    DHCP Lease: 4 hours
    c. Under the "NAT" sub-tab:
    i.) nothing should be checked;
    ii.) nothing under Port Mappings either
    3. Under the "Printers and Advanced" tabs up top:
    Nothing special needs to be configured there.
    THAT'S IT.
    =============
    I. Configure your AEX(s)
    Select the AEX from AU, and choose "Manual Setup"
    1. Under the "AirPort" tab up top:
    a. Under "Base Station" sub-tab:
    i.) pick a unique name for this unit, same logic as for AEBS
    ii.) pick a password specific for accessing this unit, same logic as for AEBS
    iii.) Set time automatically: be sure to use the same settings used on your AEBS
    iv.) Options: no need to set any
    b. Under "Wireless" sub-tab:
    i.) Wireless Mode: Participate in a WDS network
    ii.) Network Name: same name used for AEBS, this is the name of your wifi network
    iii.) Channel: same as AEBS
    iv.) All settings here (those above, plus Security and Password & in Options button) should be the same as for AEBS settings on this tab
    c. Under the "WDS" sub-tab:
    ...if AEX is "in the middle" (as described above):
    i.) WDS Mode: WDS relay
    ii.) Allow wireless clients: check (unless you only want to bridge between the edges without letting folks connect on this AEX in the middle)
    iii.) WDS Main: set to the AirPort ID (aka MAC address) for the AEBS. You can find it on the bottom of the AEBS, either labeled as such or at the bottom beside the logo of a wireless signal (square logo, with semi-circles mimicing a radio signal).
    iv.) WDS Remotes: click the '+' to add any AEX's that will connect to this relay rather than directly to the AEBS. Same deal as above, use the name in the description and use the AirPort ID from the side of the AEX (not the Ethernet ID).
    .....if AEX is connecting to a relay ("on the end", as above) or if there is no relay and AEX connects directly to the AEBS:
    i.) WDS Model: WDS remote
    ii.) Allow wireless clients: checked
    iii.) WDS Main: if connected to a relay, use the AirPort ID of the relay AEX. If connected to the AEBS directly, use the AirPort ID of the AEBS
    d. Under the "Access" sub-tab:
    i.) MAC Address Access Control: Not Enabled (for now, you can change later)
    2. Under the "Internet" tab up top:
    a. Under the "Internet Connection" sub-tab:
    i.) Connect Using: AirPort (WDS) -- should be selected and gray'ed out.
    ii.) Configure IPv4: Using DHCP
    iii.) Ethernet WAN Port: Automatic (Default)
    iv.) Connection Sharing: Off (Bridge Mode)
    3. Under the Music, Printers and Advanced tabs up top:
    Nothing special needs to be configured there. You can worry about AirTunes settings later...
    That should be it. I'd recommend setting up the AEBS first, then the relay (if applicable), then the remotes. Initially, you can bring each unit in the same room with you for configuring. After configured and restarted the AEX should blink then turn solid green. If it turns green you should be good to go.
    HOPE THIS HELPS. As noted above, I did not config through AirPort Utility 5.3.1 so I haven't tested this procedure through that app. However, after getting my network to work I went back and transposed all settings into this post to help others. Please provide feedback on whether or not this is working, so we can collectively try to move towards a setup procedure that works for everyone....
    Good luck!
    Message was edited by: b.byrd

    I'm not convinced that the problem lies in Airport Utility. This same thing was happening to me, nearly exactly as you describe it. The thing is that with me, the problems clearly started when I updated the firmware in my Airport Express (n). That's when all the wacky stuff started happening. Sometimes it would show up in AU, sometimes it didn't and even if it didn't, I could still access the internet through it.
    But as you said, the problems got really bad when another Express (b/g) was put on the network with it. Even when it did work, the (b/g) would make it impossibly slow.
    You know more about this than me, and clearly have more patience if you've restarted the network fifty times. I gave up at about ten.
    In any case, your solution is more of a work around and if you're still having that slow connection problem, I'm not sure you've got it. But thanks for your reporting of this. At least I know I'm not crazy.

  • Airport Extreme Base Station - I am ready to throw this thing...

    Dear All,
    I'm about ready to throw this thing out the window, along w/ everything else from Apple I own... Sorry, at my wits-end and have finally had it with this thing.
    My g/f and I live in an apt with an Airport Extreme Base Station (AEBS), 10/100baseT Switch, Xbox 360, PC clone tower (PowerSpec), and two Centrino Laptops... The topology our network is the following
    DSL == Modem => AEBS => 10/100 Switch => (XBox 360, Powerspec)
    Every other day, the AEBS drops out for no obvious reason. Not only for no reason, it DROPS the connection and causes interference on our wired network. If I'm playing Call of Duty 2, for instance, and using Skype at the same time, anywhere from 10-30min later, the WiFi connection will drop altogether and the wired network will go down too.
    I've done multiple hard-resets and the issue persists. Apple wants $80 to talk to me (after we paid $150 for it because it's supposedly "the best") after only owning it for a little over a year. It seems that this problem has been persistent.
    My g/f finally cracked down and bought a Verizon EVDO card and uses it while she is out, but in the house because she cannot use our home network reliably.
    I've tried using it on WPA2, WEP, and even left it open but the thing still drops for no reason...sometimes within hours, or two two days. I'll come home, boot up my laptop, and the WiFi is completely gone...non-existant. Boot hers, same thing... I doubt it's interference because we have 1 cordless phone and it's a 900mhz, which we rarely use anyway.
    Does anyone else have any of the problem(s) we're having? This has been semi-often since we got it, and all Apple told us was "interference" and won't help us because we use PC (I used to own a Mac, hence why I got this).

    Update: Well, the AEBS 'bombed' out again when I got home on Friday, no access whatsoever.
    I unplugged my DSL modem from it, plugged it in directly to my HP notebook, and was surfing the 'net w/out a problem. Power cycled the AEBS and it worked fine. That was just over one day on firmware v5.5.1, longer than it lasted on v5.7.
    Here's my conclusion...
    I'm 'convinced' that v5.7 is buggy and it's known, or well documented. It will cost more money to fix it, or release a new firmware version that repairs the bugs from v5.7, than to just leave it alone and hope people either downgrade to v5.5.1 or purchase a new AEBS (w/ 802.11n).
    After countless hours of dealing w/ this, of which I feel like a complete and utter fool, I went out and bought a competitor's product (Linksys) and installed it on Saturday morning. As of this writing, I've had no drop-outs and the access seems to be more punctual, or responsive than when I was accessing under my AEBS. Therefore, I'm happy to say my problem of unreliable WiFi access in my apt is solved, but only after spending $50 to purchase a new router.
    I spent $180 on the AEBS and I can remember the first time I had to call AppleCare about printing issues I was having with it; I could print from Windows XP (both wired and wireless), but not from Tiger OSX 10.4. No-one had a clue, but was only told that the issue was my "printer" not the AEBS or my Mac. Despite repeated attempts to re-inform that it works just fine under Windows XP with both my Lexmark and Canon inkjets, it would not print properly (bombed out half/way through the page) under Mac OSX.
    So, here on my shelf, sits the Airport Extreme Base Station that I paid $180 for, and it is basically useless. Apple could care less about it, but then again, why should they--after all, it had a 1 year warranty and despite trying to resolve issues I had w/ it while it was in fact within the warranty period, that time has come and gone.

  • Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

    I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
    The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
    Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
    Thanks

    The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
    If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
    So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
    Assuming your AE is gen3 or greater.
    You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
    And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
    If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
    If your AE is G wireless or earlier model.. really the time has come for replacement.
    If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
    You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

  • How do I open the same ports on an Airport Extreme Base Station for multiple computers at the same time?

    As the title suggests...
    I have a mix of five Mac and PC's at home using an Airport Extreme Base Station as the router.   I need many ports opened on the AEBS for all of the computers- not just one computer.  (for example: three people want to play TF2 on Steam at the same time; each machine needs the correct ports open on the router).   Port forwarding  only allows me to forward a given port to a single IP, yet I need that port open for five differnt IP's, all at the same time. 
    How do I do that on an AEBS?
    In the same way, I have a small office of four iMacs using an old airport with the same exact issue.   I would like to be able to connect to all of them remotely with Apple Remote Desktop, but the port forwarding on the airport only allows a port to forward to a single IP.   I want to be able to tunnel into the office network and log onto any machine behind the Airport extreme... not just a single IP.    I currently have it set up where I can tunnel into the office from my house, I can find the one machine that the port forwarding has been assigned to, I can log on and everything is just fine... with one machine.    How do I open the firewall for the other machines? 
    TL,DR version:  How do you open ports on an Airport Extreme Base Station instead of forwarding ports?   Forwarding ports doesn't work for multiple IP's.  

    You can open a single or multiple ports to a single device or different ports to different devices, but you cannot open the same port to multiple devices via the AirPort Utility for the Apple routers.

Maybe you are looking for