Airport Extreme Base Station - Wireless AND Hardwired connections

I have an Airport Extreme Base Station. I am under the impression that I can connect a hardwire via ethernet to my iMac, as well as use my wireless connections on my iBook. I am connected to the internet via my local Comcast Cable system on a SurfBoard SB4100 modem. I have one Ethernet port on the back of the Base Station connected to a Farallon iPrint Adapter for my antiquated (yet far more reliable than ANY injet I've owned) laser toner printer. I have a McAlly 5-port ethernet hub. I have a variety of ethernet cables, some with 8 wire connections, some with 4 wire connections. (Currently a 4-wire cable connects from the base station to the iPrint adapter) My total system has been dismantled for some time and I have been sailing through with the wireless connection on my iBook. But now I have a need to have both computers attached to the internet. I would rather have the hardwire connection and the wireless at the same time - if possible. The iMac is still on system 9 (stop laughing!) and I cannot afford to upgrade to 10 at this time.
Can anyone help me?

I am under the impression that I can connect a hardwire via ethernet to my iMac, as well as use my wireless connections on my iBook.
Yes that is possible.
Insert the Ethernet hub between the Farallon iPrint Adapter and AirPort Extreme base station (AEBS).

Similar Messages

  • Airport Extreme Base Station Wireless Woes

    Hi,
    I just bought this dual band Airport Extreme Base Station on 3/10/2010. After I setup the Airport, I have difficulties connecting my iphone 3GS to the base station. My iphone 3GS is able to see the wireless network but not able to join it. Only my macbook pro is able to connect wirelessly. My windows PC and iphone 3GS could not.
    I wonder whats could be the problem?
    Some logs from the base station:
    Oct 06 23:00:04 Severity:5 Associated with station <mac address of iphone 3GS>
    Oct 06 23:00:04 Severity:5 Installed unicast CCMP key for supplicant <mac address of iphone 3GS>
    Oct 06 23:00:04 Severity:5 Disassociated with station <mac address of iphone 3GS>
    Oct 06 23:00:04 Severity:5 Rotated TKIP group key.
    Setting of Airport Extreme Base Station:
    Wireless Security: WPA/WPA2
    Wireless Channel: Auto
    Creating a new network
    Things I have tried:
    1) Changing the wireless channel
    2) Removing the wireless security
    Thanks

    I think I manage to find the problem on why my airport extreme keep on dropping connection.
    This is my connection.
    Cable Modem -> Airport Extreme -> Aztech Gigabit Homeplug 1-> Aztech Gigabit Homeplug 2 -> Dlink DIR-825.
    When I plug out the conenction from Airport Extreme to Aztech Gigabit Homeplug 1, I am able to connect to the wireless using iPhone 3GS. Once I plug back the connection and do a refresh the iPhone 3GS wifi connection, I am not able to connect the wireless.
    Hmm, anyone faces the same problem?

  • HT4145 I have an Airport Extreme bas station now and I want to know if I can use an Airport Express to extend my network or do I have to use another Airport Extreme base.

    I have an Airport Extreme Base Station now and I would like to know if I can use an Airport Express to extend my wifi network or do I have to use another Airport Extreme Base Station.

    This AirPort Express:
    http://www.apple.com/airportexpress/
    It is the only Express with 2 Ethernet ports. All others are "old"
    Apple does not specify a model number in their product information, but it is A1392 in the U.S. I do not know if Apple uses different model numbers in other countries.

  • 2 airport extreme base stations later and still no internet connection-

    Sorry - yet another beginner with internet connection troubles! (I have read all the posts I could find relating, but without any help).
    I have had a Demon broadband account now for about a month (I’m in the UK) and in that time I have purchased a D-Link DSL-300T Ethernet modem and an Airport Extreme Base Station. I got wireless internet working relatively easily – with a powerful range over the whole house and garden, but then one Sunday night, the internet connection via the base station suddenly ‘died’.
    I spent the following 3 days scrutinising all of my settings of both the Modem and the Base station, re-setting both, and bought new Ethernet cables / micro filters etc but with no luck. (I’ll point out at this stage that my broadband account is still active, and if I connect the Ethernet modem directly to my iBook [wired] I can still get my broadband connection. Alternatively, I tried daisy chaining the modem to the base station and then via an Ethernet cable to an iBook, but no connection could be made).
    When wireless, Airport Admin recognises there is a modem there, and under preferences > network under Airport it states I am connected to the internet – but I’m not.
    I then phoned D-Link and they confirmed my firmware was up-to-date for use with Apple products and talked me through all of the modem settings and tweaked a few things, but there was still no connection to the base station. I then phoned Apple. They were incredibly helpful (as ever) and after 35 min. came to the conclusion the base station might not be re-setting itself properly. The replacement one came yesterday, and again I spent a number of hours trying to get it connected to the internet, but there is still no internet connection via airport and I can confirm this from both my eMac and iBook.
    Reading through the forums on here, I understand that my particular modem is problematic with the base station, but I can’t work out why it use to work and now it doesn’t! One theory I have investigated is that the firmware of the base station is two advance for the modem following an update, but after reinstalling the original firmware I started with, I still have no luck.
    - The eMac is running 10.3.9 / iBook is running 10.4.3. The base station is reinstalled with the latest firmware via system update. The first base station and the modem were delivered to me 31/10/05.
    Any help or suggestions would be really appreciated if anyone has any ideas
    Thanks for your time
    Will.
    UK.

    http://discussions.apple.com/thread.jspa?threadID=2316
    78&tstart=0
    I think if you follow the instructions I gave in this
    link you will be fine.
    Remember, If you for any reason loose your
    connection, it is normally always a Power Issue..Your
    ISP is down for service ..or some other anomoly, If
    you were good before your settings will still be
    good...Good Luck...Don
    Hi Don,
    Thanks for you quick response. I printed off the instructions you posted on the support forum before, and ran through your procedue exactly, (twice) but I'm sorry to inform you that I haven't been able to re-establish my wireless internet connection. Would it be safe for me to assume at this stage that my modem is indeed fualty? It contines to work fine independantly, (I'm using it right now) but it can't seem to make contact with the basestation.
    Will.

  • IMac does not see Airport Extreme Base Station wirelessly

    Trying to use my existing PC hooked up to Airport Extreme BS via ethernet cable, which works fine. I then open Airport Utility on my iMac and it scans for wireless devices but it can't see the AEBS (located beside it). Opening Base Station tab and there are no solid headers to click on, just the soft grey headers. I am fairly new to Apple product so if I've left any info out to further troubleshoot please let me know.
    Eventually I would like to connect my Apple TV, located downstairs, wirelessly as well as use an Airport Express (wirelessly) to boost the signal if need be due to concrete walls and floors in construction of house.
    I have OS X Version 10.5.8 (up to date), Intel, Airport Extreme Wireless Card.
    Thanks for any help out there.

    Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
    Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
    Any help would be greatly appreciated.

  • Airport Extreme Base station wireless setup problem with Zyxel 2602HW d1a

    Hi!
    Just bought a new Airport Extreme Base Station and it just doesn't work. Probably my fault, your help is very welcome!
    My router Zyxel 2602HW D1A is the main router/modem. I can only connect to it wirelessly with my AEBS (so not via Ethernet/WAN). But, it doesn't seem to connect to this Zyxel in the wireless way. After I setup the AEBS to connect with this network I have to reset it to factory settings. Is it possible to connect only via wifi? Is it possible to this Zyxel? How can I setup the Zyxel to have everything ok to be ready for communication?
    Firmware is up to date btw.
    Thanks!
    Bjorn

    Hi Tesserax,
    Thanks for replying. I would like to share USB attached printers and hard drives just with my 'own network' attached to the AEBSn. The other network I use just for the internet connection. Preferably the other network can't access my AEBSn network.
    Am I clear? I am not sure
    Message was edited by: BoMacBook

  • Recovering Old Datas on New Drive + Setting Airport Extreme Base Station old and new ones

    Hello All,
    Situation:
    -iMac 24" Alu/2008/2.8 Ghz Intel Core 2 Duo/ 2Go DDR2 SDRAM
    -2 Airport Extreme Base Stations mushroom type,
    -1 Airport Extreme Capsule Model: A1143
    The original 320 Go Hard Drive of my iMac crashed few months ago. A "technician" installed a new Hard Drive 235 Go while trying to recover all datas from old one. Failed.
    No back up. The old disc needs to be unlocked in a dustless atmosphere. Quite expensive at the moment.
    I decided to install OS X from sratch with the original Install Disc delivered with my iMac.
    OS X is 10.5
    Once on line I updated all pre-installed softwares. Among which Aiport Utility 5.6.1 today.
    Problem:
    I would like to get bigger hard drive disc, 1To for example. Does this still exist for this iMac 2008 Alu ?
    How can I do to get my iMac again to OS X 10.9 ?. Does this mean I need to buy all intermediate levels again ?
    How do I get my softwares (the ones on the original Disc: Pack office, Pages, Numbers, etc ...) back on track again, since my iMac is now more like down to factory level ?
    Extending my internet provider from the WiFi router via my 3 Airport Extreme Base Stations: 2 mushroom type that need OS X + Airport Utility softwares at a certain level, while the Capsule might need another level. Right now I tried to set up the 3 of them with this Aiport Utility and though they all recognize the provider network, I can never conclude to extend it with the Base Stations: it drops the case. (WDS trouble which I don't even know what it is, or the Base Station simply desapears from Airport Utility scan, ...)
    Thank you all for you attention.
    Your comments are welcome especially if you have any knowledge on these various subject.
    Can't wait to read your piece of advice.
    Lionnel From Paris (France).

    me too... i connected my hard drive with all my music but i cannot see any of the music that used to be in my itunes... i checked and its there (when I connect the HD directly to my computer) but not when is plugged into the Airport Extreme... Please help!

  • What is Error 2813 while trying to install  my Airport Extreme Base Station? and How can I fix it? Thanks

    What is Error 2813 while trying to install  my Airport Extreme Base Station(A1143/MA073LL/A)? and How can I fix it? Thanks

    Did you remember to completely power cycle the entire network?
    You would want to do this after any update or change to the network.
    If you did not do this yet......things are out of sequence.
    Power off everything on the network.....all devices.....power down order is not important
    Wait a few minutes
    Start the modem first and let it run a minute or two by itself
    Start the next device connected to the modem the same way
    Work your way out on the network starting each device about a minute apart
    Check the network

  • Airport Extreme Base Station N and Buffalo Linkstation

    I want to set up a Buffalo Linkstation with my Airport Extreme Base Station
    I have two options on the linkstation
    1. ethernet
    2. USB (female port)
    Can I use the NAS over ethernet? Or do I have to use USB? If I use USB will it work if both the linkstation and the base station have female ports.
    Will a USB with both male ends work? Who makes that?

    I've decided to use the drive as a network drive and I've gone into the control panel and changed all the folders to Mac/PC
    Can I use Backup to backup to a network drive? Or is there a better program?

  • I own an Airport Extreme Base Station with a HDD connected. Can I copy my iTunes Library to this HDD and play it on my iPad?

    Now I use Home sharing. This works well, but I have to keep my computer running with iTunes open. I like to shut down my computer.

    Hans Brinker wrote:
    I like to shut down my computer.
    currently i know of only one way to achieve that. using FileBrowser on iPad, you can access media files stored on
    a NAS
    an external HD connected to an airport extreme
    a time capsule

  • Airport Extreme Base Station- wireless printer- wired computers able access the printer

    Airport with a wireless printer- will wired computers be able to access the printer?

    Yes.
    A printer on your network is accessible to any computer on the same network. Wired or wireless makes no difference.

  • Airport Extreme Base Station Portscanning my System?

    Bought the AEBS today and got it set-up in about five minutes; very nice. I then moved on to another (and completely different) problem, which involved opening system.log. What I discovered thousands of messages that read along the lines of:
    "Aug 3 17:13:13 My-Computer kernel[0]: Stealth Mode connection attempt to UDP xx.xx.xx.3:51539 from xx.xx.xx.1:192"
    where xx.xx.xx.3 is my G5 and xx.xx.xx.1 is the AEBS. I don't know which port number the AEBS started with (hopefully not 1), but it is clearly incrementing by one.
    I was able to learn that 192 is used by the base station for PPP status or discovery, but could not find anything more. (If it is of help, I'm connected to the net via Verizon and a DSL modem. I set up the AEBS using the wizard, which defaulted to PPP over Ethernet.) My questions are:
    - What exactly is it doing?
    - Will it stop once it gets through the full range of port numbers?
    - Can I make it stop? (I realize it's not really hurting anything, but it certainly seems like bad behavior to me.)
    - Will it do this each time I boot my system?
    Any other information is appreciated.
    Thanks,
    David
    iMac G5 Mac OS X (10.4.7)

    Will the airport extreme base station work with WD my cloud 3 tb drive?
    Yes it should work with your AirPort Extreme base station.
    Would I connect it to the airport extreme or could I connect it to my imac ethernet connection.
    You'll want to connect it to one of the available LAN (opposing arrows) ports on the AirPort Extreme.

  • Wireless connection to internet with mac pro tower and airport extreme base station?

    Hi, I have an airport extreme base station and a mac pro tower without a airport card. My internet wireless router is a great distance from my computer so I can't connect the base station directly to the router. I've attached the airport extreme base station to the tower via an ethernet cable, the base station seems to be wirelessly connected to the home network but the browser is showing "not connected".
    Please help.
    Thanks

    Shouldn't the Airport base station be able to connect to it wirelessly?
    It might be possible, but the Ethernet ports on the AirPort Extreme would not be enabled, even if it did connect to the Thompson' WiFi signal.
    As Tesserax notes, among the Apple routers, only the 802.11n versions of the AirPort Express have the capability to "join" a wireless network with the Ethernet port being enabled.

  • Problem consistently printing via new (summer 2011) AIRPORT EXTREME BASE STATION and Brother wireless printer (model HL5370DW). What am I doing wrong?

    Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
    Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
    Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
    Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
    My theories:
    - true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
    - The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
    QUESTIONS:
    - Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
    - I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
    Rule out:
    - wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
    Any help will be greatly appreciated.
    Thanks in advance!

    13 ASCII characters = 104 (aka 128)-bit WEP
    encryption
    If turning off WEP works, then you just need to
    provide the cameras with the "Equivalent Network Password".
    One of the problems with WEP is that the actual
    standard relies on a 10 character HEX key for 40bit
    WEP and a 26 character HEX key for 128bit WEP.
    In order to make things easier, vendors use certain
    algorithms to convert simple alphanumeric passwords
    (or passphrases) into HEX keys, thus enabling the use
    of simple easy to remember WEP password rather than
    lengthy HEX keys. The problem is that different
    vendors use different algorithms to generate the HEX
    key and therefore a ASCII password on an AEBS will be
    hashed differently on a non-Apple client and vice
    versa.
    You may find the following article helpful:
    - Apple article, especially the part about
    "Third-party client to Airport".
    Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
    I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
    Thanks again for your help and suggestions... I really appreciate it.
    geoff

  • How do I configure an Airport Extreme base station to receive and distribute a wi-fi network from a broadband wireless router?

    I have recenly upgraded my broadband service and now have a wireless router. My old network configuration was a router connected by ethernet cable to an Airport Extreme base station which then broadcast my wireless network (I also had an Airport Express base staion set up as a wi-fi booster elswhere in the house).
    I now have two networks (my original network and the new network from the wireless router) and wish to amalgamate these into one.
    Ideally I wish to use the Airport Extreme base station as the "remote" booster (I have purchased Powerline adapters for this purpose) but don't know how to configure the Airport Extreme base station in order to to this.
    Can you advise on the best set up for this please?
    My Mac is running OS X 10.8.2 and the Aiport untility is version 6.1.
    Thanks in anticipation.

    The AirPort Extreme should be configured to "create a wireless network" with the same WiFi network name, security type (usually WPA2 Personal) and password as your existing router. It should be configured as connection type Ethernet and be in bridge mode.

Maybe you are looking for