Airport extreme- can it join my current wireless network?
I'm trying to get the extreme airport up and running. The software wants to it to start it's own network. I have verizon FIOS internet with actiontec router already up and running. I was just going to use the router to hook up my external hard drive- I don't want to have to switch from my fios wireless over to the base station wireless to share a file- how do I get it to play with my current router?
zimm17, Welcome to the discussion area!
Sorry that is not possible wirelessly. The actiontec does not supports Apple's WDS.
The only way to make it work is to run Ethernet from the actiontec to the AEBS.
Similar Messages
-
I just installed Airport Extreme. It works as a wireless network on my Macbook. It won't connect with my Windows Visa PC. Message reads: "settings saved on this computer for the network don't match requirements of the network." I seem to need to enter a security key/passphrase to connect to the PC. Where do I find them?
Thanks for your help.I assume that you have Wireless Security enabled on your AirPort's wireless network. The issue maybe that the PC is unable to use the WPA password itself and will require using the Equivalent Network Password instead.
To get this password, you will use the AirPort Utility from the MacBook:
Start the AirPort Utility > Select the AirPort base station > Manual Setup
Now, before doing anything else, go up to the utility's menu bar at the top of the screen, and then, choose "Base Station," and then, Equivalent Network Password from the drop-down menu. You will see two items: 1) WPA Password, which should look familiar to you, and 2) WPA Pre-Shared Key. It should be a long hexidecimal set of numbers and letters. Jot down this second item.
You will want to use the value you just jotted down when entering the password from the Windows Visa PC. -
Can my older Airport Express 802.11g join an existing wireless network
I have a Airport Express 802.11g firmware version 6.3 . Using the most recent Airport Express Utility I can set it up as a base station on its own independent network but I cannot join it to my existing home wireless network. As I go through the wizard (or manual setup) It just does not detect/display any existing wireless networks. I have plenty of mobile devices in the house that can see the wireless network...and next doors network.
So, it begs the question ... is an 802.11g unit actually capable of joining another network or is this capability available on later models only. A search of apple support and the wider internet for "Airport Express 802.11g capabilities" yeilds a blizzard or useless info.
Thank youSorry, I cannot help on Windows since I do not have a Windows 7 machine here to test. I have used XP in the past and AirPort Utility appears to be virtually the same in Windows as a Mac. I assume that this is the case for AirPort Utility 5.6.1, and it should be able to configure the Express.
The older Express will join most wireless networks if the following conditions are met:
1) The Express is functioning correctly.
2) The wireless network name is 12 characters or less and it contains only normal letters and numbers. Avoiding blank spaces in the wireless network name will help improve the chances of the Express joining the network as well.
3) The wireless router is broadcasting a compatible signal that would allow the "g" Express to connect. If your network is broadcasting a wireless "n only" signal, the Express cannot connect to this network.
4) The wireless security on the network is set to a WPA compatible setting. That is because the older Express has difficulty joining 3rd party wireless networks using WPA2 Personal or WPA2-PSK-AES encryption. In other words, if your network is now using WPA2 Personal or WPA2-PSK-AES settings, the "g" Express will probably not be able to join the network.
5) If you are using MAC Address Filtering on your network, the MAC address of the Express will need to be included in your settings.
6) The wireless network password uses the same guidelines that appear in 2) above
The items noted above will provide the Express with the best chance of joining your network. Plan to use the Manual Setup option in AirPort Utility and be prepared to use the Option or Alt keys on the PC if needed.
If you are looking for a guarantee of success in advance for this task, I cannot provide that and you should wait for another user to post who might be able to meet your requirements in that regard. -
Airport Express won't join my existing wireless network...
I have Broadband in my house. I have a wireless modem also. I have spent hours trying to have Airport Express join the network so I can use the music streaming feature, but I have so far not been successful. I have seen a lot of references to it being very easy and straightforward to set up with it doing most of the work itself. As in, plug in AE to a power socket, open Airport Utility and follow the instructions... It doesn't appear to be that simple, not by a long shot. Can anyone outline how this can be done in simple steps? All of the online steps I have tried do not work, with many of them referencing aspects of the Airport Utility GUI that don't seem to exist...
Any help would be greatly appreciated.
For the record, I DO NOT want to replace my existing wireless router, i just want AE to join the network...
Thanks...
RonanI have the same problem - the AE wont join my Draytek 2600 wireless network. I can stream music wired, but it refuses to join the wireless network. I have tried WEP, WPA, WPA 2 etc. Always get amber flashing light. Ive spent about 5 hours solid on it so far, and I'm a networking expert.
No other device on the planet has problems connecting to my wireless. currently I have:
1) Belkin wireless Skype phon (no problems)
2) SOHO wireless IP camera (no problems)
3) Intel Macbook pro (no problems)
4) G4 Macbook (no problems)
5) Dell D600 XP notebook (no problems)
Try to connect the AE? No chance. Its just broken.
I have tried every conceiveable manual setting on the device also.
If I manually set the ip (outside the DHCP range, but within the subnet), subnet, DNS sever, domain etc, I get a GREEN light, but nothing can communicate with it. The utility cant see it, and itunes cant see it.
The real problem is there is no way to know if the problem is with DHCP or the wireless. Does green light mean it has a wireless connection, or it has a valid IP?
Interestingly, if I start it with a wired connection, get a green light, then stream music to it, then pull out the wire, the green light stays, and music players for about another minute (presumably wirelessly, but who knows?) before the music stops and the device (replete with green light), becomes dead to the network.
APPLE desperately needs to sort this out. Its junk. -
Attempting to eliminate a dead spot in Wifi coverage [and implement AirPlay] have one Airport Extreme 802.11n and two Airport Express 802.11n's.
http://support.apple.com/kb/HT4145
The Airport Extreme is of course connected to cable modem and Ethernet switch, and one Airport Express is connected to the Ethernet network. As per instructions for creating a "Roaming Network", Airport Express is set to same SSID, security type, and Password.
Questions:
1. How does the client device know which Airport to connect to? In other words, will it switch to the closer WiFi transmitter automatically? The WiFi reception problem is intermittent in the fringe areas so what I do not want it for it to stick with the more distant Airport Extreme in the basement when the Airport Express which is closer will work better.
2. How can I tell which of the Airports the attached client device is using?
The third Airport Express will be in a third location - I was planning on using it also for expanding coverage but after reading the warnings about performance suffering when purely using WiFi for the expansion in this location ("Wireless Extended Network" without an ethernet connection) I have figured that the single wired Airport Express will be adequate and will use the third Express to do Airplay only.
http://support.apple.com/kb/HT4259
Question: Can I use this second Airport Express to extend the wireless network via "Extended Wireless Network" while the other two are in "Roaming Netowrk" configuration? Without bogging down??
Mitch1. How does the client device know which Airport to connect to?
The Mac computer will automatically connect to the wireless access point with the strongest signal...which is probably the closest AirPort. An iPhone or iPad may not do this and will tend to stay connected to one AirPort.
2. How can I tell which of the Airports the attached client device is using?
On a Mac, open Macintosh HD > Applications > Utilities > AirPort Utility. Click on one of AirPorts. In the area to the right, locate the AirPort ID and jot that down. Then do the same for your other AirPort.
Move your Mac near one of the AirPorts and log on to the wireless. Hold down the option key on the Mac while you click the fan shaped AirPort icon at the top of the screen. Look for the BSSID. That is the AirPort ID of the device to which you are connected.
If you are close to the "remote" AirPort, and you see the AIrPort ID of the "main" router when you are testing, then you know that the network is not configured correctly.
Can I use this second Airport Express to extend the wireless network via "Extended Wireless Network" while the other two are in "Roaming Netowrk" configuration? Without bogging down??
There will be a modest 10-15% bandwidth loss with the "extend" setup, assuming that the Express is located where it can receive a strong wireless signal from the AirPort to which it is associated. You can avoid the bandwidth loss if the Express is also connected via Ethernet as part of the roaming configuration. -
How many Airport Extremes can I use to create a network?
Hi all.
I've taken to using two of the dual-band Airport Extremes whenever I need to create a wireless network over a larger than usual space, obviously using one as base and using the other to extend the network.
Can I add a third or fourth Apple Airport Extreme to further extend the network?
ThanksCan I add a third or fourth Apple Airport Extreme to further extend the network?
If you are asking about wireless only extension, it is important to remember that the "extend a wireless network" setup works like the hub and spokes of a wheet. Your "main" AirPort Extreme is the hub and the remotes reside at the end of the spokes.
You can have multiple remotes if you wish, but keep in mind that each remote communicates directly to the hub....not to another remote at the end of another spoke.
For this reason, you want to lcoate the "main" AirPort Exteme as centrally as possible within you home so the extending devices will operate correctly.
If you are asking about extending by connecting the "remote" devices to the "main" AirPort Extreme using an Ethernet cable, you can have as many remotes as you wish....up to about 250. -
How to get this Airport Extreme base station to produce a wireless network?
I had this Airport Extreme base station working fine at the house that I moved from a couple of days ago.
After my house move, however, it seems that the AE base station isn't producing a wireless network. My wireless laptop isn't detecting a wireless network. Also, the left hand side light on the AE base station is not lit.
The AE base station was softly cushioned during house the move.
Regarding configuration:
My non-wireless iMac (running 10.3.9) connects to the AE base station via an ethernet cable.
Before my house-move, I regularly connected wirelessly via the AE base station from a couple of wireless-equipped laptop computers.
I was using AE software version 5.6. (In desperation, I have just updated to version 5.7 - but that hasn't improved or changed situation.)
At the new house, I found that I had to reset the AE base station back to factory settings before I could successfully connect to the internet through the AE base station from the (non-wireless) iMac.
Since resetting the AE base station at the new house, I can also print via a USB printer that's plugged into the AE base station.
I just cannot pick up any sign of a wireless network from the AE base station.
G4 Powerbook Mac OS X (10.3.9) Problem started while I had Airport Extreme software v5.6. No improvement/change after v5.7 update.Sorry for my delay in closing this issue.
I got the wireless network running again - though I'm not sure which of a "litany" of separate actions (which I gleaned from dialogs in several similar postings for similar issues to mine) was the solution. I suspect it was one of the following two actions, which have stuck in memory:
1) I relocated a nearby cordless phone cradle/charger/base-station from alongside the Airport Extreme base station to about seven feet (two meters) away. However, the cordless phone is about eight years old, and I believe its radio frequency is far out of the range that I have read (in similar postings) can interfere with the Airport Extreme base station.
2) I re-set the Airport Extreme base station, (a) by depressing the tiny reset button at the rear of the base station for more than 5 seconds (until the led started blinking), (b) from Utilities/AirPort Admin Utility/Configure/Restart. However, I had reset the Airport Extreme base station those ways previously without that restoring the wireless network. Also, I didn't record the sequence of the multiple resets and the configurations at the times of the resets. -
Airport Utility cannot see Airport Extreme Device even though connected to wireless network
I'm trying to set up a Macbook Air for my wife. I have a home network of four Airport Extremes that were configured in bridge mode with an authenticated SSID and one that is open for guests. On my PC my airport Utility sees all of the base stations and can configure them fine. On the Macbook air the utility cannot see any of the base stations no matter how many times I scan. The strange thing is that it can see both wireless networks. A fact that may be related to the problem is that the Macbook Air cannot authenticate into the secured SSID. The password is correct. Other machines (PC/Mac) all have no problem. Apple TV 2's, iPad's, and iPhone's all have no problem. I'm stumped.
Any help is appreciated! Thanks.As usual in recent years, Apple creates and ships a problem (latest MacBook Air + Airport Extreme N + Airport Utility 6.1), and when multiple users encounter the problem, and post about it, nary an Apple supoort person to take ownership, so threads just die, like this one did. I'm having the same problem, and as a committed Apple customer, I just want to find any oither company to do business with.
(I'm sure connecting by wired Ethernet would work, but THE AIR DOESN'T HAVE AN ETHERNET JACK!!)
Love this community. Have had it with Apple.
Sincerely,
Marc -
How do I set up wireless network extension/expansion adding Airport Express to existing Airport Extreme Network??
OK, thanks for the clear information, this really helps.
Locate the AirPort Express about half way between the AirPort Extreme and the general area that needs more wireless signal coverage. The more that you have line-of-sight between the AirPort Extreme and AirPort Express, the better the performance will be.
Power off the AirPort Express for a few minutes
Hold in the reset button firmly...and keep holding for an additional 10 seconds while you simultaneously plug the power cord back into the back of the AirPort Express
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light
This process is tricky.....you almost have to have 3 hands to do this.
If you have an iPad or iPhone, the setup is almost too easy to be true. In that case.....
Tap on Settings (gear icon) on the home screen
Tap on WiFi
Under the heading of Setup a New AirPort Base Station....
Tap on AirPort Express
The utility will analyze things for a minute, then suggest that the Express be configured to extend the AirPort Extreme network
Type in a device name that you want to use, then tap Next
The utility will set up everything for you automatically. When you see the message of Setup Complete, tap Done and you are good to go.
If you want to use the Mac running (10.6.8) for the setup.......
Make sure that the wireless is turned on at the Mac
Open Macintosh HD > Applications > Utilities > AirPort Utility
Select the AirPort Express and click Manual Setup
Click the Base Station tab under the row of icons
Enter a device name for the AirPort Express
Enter a device password for the AirPort Express
Verify the device password
Adjust the Time Zone setting
No other adjustments are needed here
Click the Wireless tab below the icons
Set the Wireless Mode to Extend a Wireless Network
Click on the Wireless Network Name box and your AirPort Extreme network name should appear as a choice. Click to select that....or manually enter the exact name of the AirPort Extreme wireless network
Make sure that Wireless Security is set to use WPA2 Personal
Enter the wireless network password for the AirPort Extreme
Verify the wireless network password for the AirPort Extreme
Click Update at the lower right of the window and wait a full minute for the Express to restart. A green light on the Express at this point will be a very good sign that things are up and running correctly.
Your Mac will automatically select the AirPort with the best signal quality. If you have an iPhone or iPad, you may need to manually turn off the WiFi when you move the device near another AirPort, and then turn WiFi back on to get the iOS device to connect to the best signal.
Good luck, please post on your results with the method that you choose. -
Hello there!
I've been looking for this info, but have as yet been unable to find it. Here's my scenario:
I have two Airport Extreme Base Stations (both are dual band) and 3 airport expresses. The main internet connection in my house is in one room, where I have an AEBS as the main wireless router. In another room, I have a bunch of ethernet-only devices. I'd like to use the 2nd AEBS in this room, plug the ethernet devices into it and have the 2nd AEBS act as a wired <--> wireless bridge (connected to the same wireless network as the 1st AEBS). I've attempted this via "extend a wireless network," but the ethernet devices don't get past the AEBS they're plugged into. Should I instead be implementing WDS?
I mention the airport expresses as I'd like to have airtunes & wireless signal in other areas, but would like to keep the set-up as simple as possible (i.e., not config the AXes for WDS unless it's required).
Thanks in advance for any help!Unlike the 802.11n AirPort Express Base Station (AXn), the 802.11n AirPort Extreme Base Station (AEBSn) cannot be configured as a wireless Ethernet bridge.
However, there are at least two ways to configure it to provide wired clients access:
Connect the second AEBSn back to the first by Ethernet; reconfigure the second AEBSn as a bridge and disable its wireless radios, or
Reconfigure both AEBSns into an extended wireless network. For 802.11n AirPorts, this would be called a dynamic WDS. The AEBSn, connected to the Internet would be the "main" base station and it would only require that you enable the "Allow this network to be extended" option in the AirPort Utility. The extending AEBSn would need to be configured with the option, Wireless Mode = Extend a wireless network, enabled.
In both configurations, the second AEBSn's Ethernet ports would be enabled for wired clients. -
Airport Express can't connect back to wireless network
Here's the situation. There was a power glitch in our neighborhood that knocked our linksys wireless router offline. We have since gotten that back up and running. Meanwhile, our 2 Airport Express (used for iTunes only) went yellow and wouldn't rejoin the network with a hard reset. I have been trying to do the factory reset. The lights do their 4 green blinks but when the Airport Utility (not Airport Setup Utility - is that gone?) tries to rejoin the expresses to our wireless network we get the following error:
AirPort Utility was unable to find your base station after restarting.
The settings for this base station have been successfully updated, but there was a problem re-joining the wireless network or finding the base station. You may need to select your network from the AirPort menu and try again.
I am confused. We are using WPA2 personal encryption and I have included that info in the Airport Utility so it's not a password problem. I am sure I'm missing something completely stupid.
Any ideas?
Thanks in advance.Hi @KenHp14,
Thank you for visiting the HP Support Forums! I see you are running into some problems getting your HP Officejet 7410 connected to your wireless network, you have attempted a USB to Wireless connection but it does not locate the network.
I would like you to start here: Installing the Printer Software on a Wireless or Wired (Ethernet) Network, please click on the Windows 8 section and complete the steps listed there.
Please let me know the outcome, I will watch for your reply.
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping! -
Airport Express can't find D-Link wireless network
Hi all,
I'm on my third AirPort Express. I'm trying to use it in client mode to connect to a D-Link DIR-655 WAP, so I can run AirTunes. The first unit was a Best Buy refurb that I was able to configure fine, but it kept dropping the connection and having other issues, so I returned it. The next two units were fresh from the Apple Store. NEITHER has been able to even find my D-Link SSID - it's not listed in the list of networks to join in client mode, and entering the SSID directly doesn't work either. I've tried resetting both the Airports and D-Links multiple times, changed SSID/broadcast/channel settings, tried turning wireless security on and off... ALL my other wireless devices have no issues whatsoever finding and connecting to the D-Link. This includes a '06 iMac, iPhone 3GS, iPhone 4, iPad, iPad2, PowerBook G4, MacBook Pro, Sony VAIO laptop, the first refurb AirPort Express... you get the point. I put in a call to Apple for the 2nd unit, and they said the radio must be broken, so I exchanged for the 3rd unit, and it still doesn't see the D-Link. Losing my mind here! Any suggestions would be greatly appreciated.
Cheers,
MarcWelcome to the discussion area, bob36!
To do what you want, you'll need the AirPort Express 802.11n. The model number, visible in the fine print on the side is A 1264.
Is this the model you have? If so, post back for some configuration tips to enable the ethernet port.
If...you have the older version of the AirPort Express, model A 1084, unfortunately this version will not allow you to do what you want to do unless your main router is also an Apple device and you re-configure both devices to particapte in a Wireless Distribution System (WDS).
The downside to the WDS is that it will drop your entire network down to "g" level speeds and cut the bandwidth by 50%. -
Airport problems - can't connect to home wireless network
I am stumped. i made the upgrade to quicktime ( it's not 7.4.5?) and suddenly airport didn't work. i input the wep password, and it returns, There was an error. When I try through Network Assist it says that the password is incorrect. Which of course, is not true. This same upgrade seems to have also created keychain issues.
I can connect without problem when hardwired through ethernet, however, I need the wireless to work.
Thanks, Thomas
ps. I'm using the same Linksys BEFW 11S4 that I have for years...First of all, I want to say that i"m surprised in 24 hours or so, no one had anything to say on this subject. To help anyone else who has this problem, I will give the answer for I have solved the problem ( desperation has a way of forcing one to figure it out by the old trial and error method).
What occurred was that some how, the keychain document for my computer ( the home document, not login nor system) was inadvertently taken out. It was in another folder, but, I didn't realize what it was since it did not have .keychain in the name. Just my computer name. I got a hunch and put it back into place. And, suddenly Safari asked for the keychain password ( which had not been working either) and i put in the computers password and it was accepted. Airport was still not connect, but, when I manually input the wep password, it accepted it and turned on. What puzzles me is why the fact that there was no keychain home document, interfered with the manual inputting of the correct WEP password in airport. That I don't understand. Nonetheless, I am thrilled to be done with this all. And to have learned yet another mac secret. ( what ever that is). So, thanks to myself and I hope that someone is helped by what I have written here. -
How to add airport express to my current wireless network
Hi guys.
I have a dlink router (ac) configured as NAT and a friend of mine gave me an airport express (ac) to extend my current wireless network.
I believe that i should configure the airport express as bridge mode in order to mantain my current ip range.
I'm trying to configure the airport express but i can't even loggin to it.
The question.
Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
Thanks so much and any help would be really appreciated.
Regards.
Francisco.Can i use this device to extend my current wireless network or do i need an airport base station to do this?.
Unfortunately, the answer is that neither an AirPort Express nor an AirPort Extreme is compatible with a D-Link router....or any other 3rd party router for that matter.....if you are trying to have the the AirPort device extend the signal using wireless.
The AirPort Express can extend a signal from another Apple router.
'm trying to configure the airport express but i can't even loggin to it.
You may have received an older version of the Express that is not compatible with the newer Mac operating system that you are using.
Look for the model number of the Express on the side of the device.....hard to see in the faint print.....you may need a magnifying glass. If you see model A1084 or A1088, these older versions are no longer supported by Lion, Mountain Lion or Mavericks operating systems.
The workaround is that you must use a Mac that is running Leopard or Snow Leopard, or a PC to be able to administer the older versions of the AirPort Express models. -
Joining an existing wireless network with airport express
Ok, am almost to the point of throwing my AX across the room
AM trying to join an existing wireless network, its from a 2Wire gateway
one of three things happen
it won't find the AX in the first place
it recognizes it, but i can't connect to it
it goes through the configuration and when it restarts the AX, it can't reconnect to either the router or the AX and it fails. if this happens i can't reconnect to my wireless network without deleting it and re-adding.
it doesn't show up in my available wireless networks at all
protected via WEP, and i have tried using all the security options.The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.
Are you using MAC address access control in addition to WEP?
Turn off WEP and see if that makes a difference?
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
WEP is now considered not to be secure and therefore it is advised you use WPA.
"WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
iFelix
Maybe you are looking for
-
Camera raw opening in a weird language
when I try to open CR2 files in Camera Raw through Bridge or Photoshop it appears in a foreign language (looks arabic or something). I have checked prefrences in all areas to make sure they are set to english and have also tried to re-install all of
-
Dublicated datasection in MS Excel from BeX
Hello All, When Im from BeX Query Designer 7.0 display the query in Internet Explorer (portal) I want to save the resulting report in MS Excel. When I do this (push the Excel button), I get the report header once and the report datasection twice. An
-
Hi; Iam very confused about the use of the key word return. I understand its functionality when it returns some value.But what's the case when we use it in the following way: if(some testcase) return; Also where will return leads to when we use only
-
I get this error--"Microsoft Visual C++ Runtime Error, Program: c:\programfiles\mozillafirefox\firefox.exe, abnormal program termination" any ideas??? no specific web site causes this to happen.
-
SUDDEN DISAPPEARANCE OF ALL FOLDERS FROM FOLDER PANEL
I use LR5, iMac ans 10.8.5. Have done so sucessfully for some years. Suddenly all the folders listed in the folders panel have vanished. The photos all appear to be present, but there is absoultely no folder tree. I was dragging an image from one fol