Airport extreme card with G4 ATI emac (1GHZ)

I've purchased a previously used airport extreme card for my emac and installed it following the instalation guide on the apple website. But with the card inserted my emac wont boot. I just get the usual apple noise then a black screen and the caps lock lights up.
The card seems to be in properly as i got the "little click feeling" you have when something goes all the way in and the antena is also connected properly.
The emac boots up fine when the card is removed.
any ideas?

Thanks, I think i'm going to send it back as i thought that it was the card at fault but thought i'd better check all options first.
The card was correctly installed and there's nothing wrong with my emac so it must be the card.

Similar Messages

I have an imac g4 purchased Dec 2003 runnung OS 10.5.8. It runs fine with airport off, but when I turn airport on it freezes with the black page, "restart by holding power key . . ." I swapped the airport extreme card with the one in my ibook G4 (purch

i have an imac g4 purchased Dec 2003 runnung OS 10.5.8. It runs fine with airport off, but when I turn airport on it freezes with the black page, "restart by holding power key . . ." I swapped the airport extreme card with the one in my ibook G4 (purchased same date and running same OS). No change in operation.
I am running wifi from verizon. Recently changed from mifi2200 to jetpak 4620 in a 3G location. Ibook running fine, desktop freezes. If I can boot desktop in safe mode and get airport turned off in time. then I can reboot regularly and imac runs flawlessly with no wireless.Have run disk utilities and TechTool Pro rebuild etc, but nothing has worked. How do I fine the culprit?

the power logix thing was really sad. apple changed so much after 10.4.8 that there wasn't a viable way to patch the software.
That statement is precisely why I don't believe in blindly updating the OS, especially in a non-standard machine.
We can't expect third parties to support us forever, and it is shameful to break something that works fine, except that we updated the OS....
I think that any upgrade or modification to a machine or the OS greatly increases the risk of trouble or incompatibility with current configuration and "new" system files.
After all, the component or software could only be tested as far as the current OS version when the component or software was released.
Beyond that, we are all "beta testing".
Following a beta tester protocol, and applying updates to a cloned system drive first, is a prudent way to approach updates, and not only for older, heavily modified machines.
After 10.4.8 and moreso with Leopard, the focus is primarily on Intel architecture, not PPC architecture.
Like it or not, we are all updating to the abyss of the extinction of our machines, unless we can be satisfied with the last stable version of OS that works well with our hardware and software.
I wish they would include the latest pkgs at least with software update.
Yes, having individual packages, rather than lump "OS X 10.x.x" updates would be nice.
This way, one could update as one sees fit. That is to say, for example, fix the Quicktime, but leave my Network alone, etc., etc.
In all fairness, Apple does provide for some breakdown of updates, but I believe there is much room for improvement, especially, as you point out, with regard to the core services portion of the OS.
Until then, I'll leave Software Update disabled.......

Will Airport Extreme Card work on all eMacs?

Will an Airport Extreme Card work on all eMacs?
Thanks,
Chase

Here are the computers that use Airport Extreme Cards.
http://docs.info.apple.com/article.html?artnum=107440
Cheers Don

Airport Extreme Card with iBook G4 against Linksys WRT54GC

I am having massive problems with connections from my iBook G4 to my Linksys Wireless Compact Router. I'm getting perfect connections with our other computer's wireless card (linksys), even with my Nintendo DS.
I've searched(googled) for answers, but all I'm finding is a lot of unanswered questions, and the ones that are answered are about the Base Station. Any firmware updates I try to find are all Base Station.
The specs are;
Wireless Card Type: Airport Extreme
Wireless Card Locale: USA
Firmware Version: 404.2 (3.90.34.0.p16)
Worst case for me is the antenna is busted. That would be horrible, since I've only had this for a year (not even).
Currently, the network will come on, but annoys me to no end with "Cannot connect to airport network".
Is there any way to fix this without resorting to buying a whole new card?

Vitality, Welcome to the discussion area!
I use a Linksys WRTP54G with no problems.
Currently, the network will come on, but annoys me to no end with "Cannot connect to airport network".
Are you using a MAC control access list on your router? If so, you need to add the MAC address of the AirPort card in your iBook.

Emac does not recognise airport extreme card.

I bought my emac less than a year ago and its running on the newest version of Mac osX. I also have a PC with broadband and a wireless router which is emitting. I was told that i needed to get an airport extreme card to let my mac use this internet aswell. I have bought the card and i installed the software on the disc and i then fitted the disc into my mac and i have checked to see that it is in firmly and so is the aerial. This said when i turn my emac on it does not search for available networks like it supposedly should and when i go into system profiler it says no information available for the airport card. I am not convinced that the disc actually installed anything onto my mac however since i cannot find any files that i would have thought would have come from the disc. Please any help would be greatly appreciated.
Emac Mac OS X (10.4.7)

P.O.R.G, Welcome to the discussion area!
There is no need to install the software from the disc. OS X contains all of the software needed to support the AirPort Extreme card.
The early eMac's require the original AirPort card instead of the AirPort Extreme card.
If you are using the correct card and the card is not recognized in System Profiler, there are only 3 possibilities:
The card is not installed properly.
The card is defective.
The eMac's motherboard is defective in the area interacting with the AirPort Extreme card

Slow Speedtest results with Airport Extreme Card

Hi,
We just upgraded our internet to a 5G network with TWC. All the devices in our home are now speedtesting at 100 mb/s wonderfully.
Except one.
My Mac Pro 8 Core 2009 4,1. Running OSX 10.8.5
The mac pro is speedtesting at only 30 mb/s while everything else (MBP, MBA, iphone 5) all speddtesting at 100 mb/s. Alla re connected to the new network.
Is the problem the older airport extreme card? Or is there something I can do in settings or firmware upgrade to sort this?
Here are the specs of the Airport extreme card on the MP:
Card Type:    AirPort Extreme (0x14E4, 0x8E)
Firmware Version:    Broadcom BCM43xx 1.0 (5.106.98.100.17)
Locale:    FCC
Country Code:    US
Supported PHY Modes:    802.11 a/b/g/n
Supported Channels:    1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
Wake On Wireless:    Supported
AirDrop:    Supported
Status:    Connected
Thanks!

tek_uk, Welcome to the discussion area!
(a) Did you connect the external 'T' AirPort shaped antenna to the back our your G5? This antenna shipped with your Power Mac G5.
(b) Compare the antenna wire connection at the AirPort Extreme card with the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card.

Computer won't recognize Airport Extreme Card

Okay, I need a little help. I bought an Airport Extreme card for my eMac today, which is what my manual told me I'd need to connect to a wireless Internet connection.
I followed the instructions to install it exactly, but the computer won't recognize that it's there. It still says "no information available" when I go look at the Airport card settings.
I'm not sure if it's a fault of mine, the card's, or the computer's. When I insert the card, should it snap into place? Should it slide out easily? How can I tell if it's in properly?
If anybody can help out, it'd make my year. I am dying to get this high-speed Internet set up. Thanks.

surfingbaku, Welcome to the discussion area!
Use the information in KB 86325, eMac: How to locate the serial number and identify your model to identify which type of eMac you have.
If you have one of these eMacs
eMac (ATI Graphics)
eMac (USB 2.0)
eMac (2005)
you require the AirPort Extreme card.
Any other eMac requires the original AirPort card.
If you are using the correct card and it is not being recognized, one or more of the following must be correct.
The card isn't installed correctly.
The card is defective.
The eMac's motherboard is defective and not recognizing the card.

How do I know if my Airport Extreme Card is going bad?

I have 3 computers on a home network. I have the router (Airport Extreme) in my guest house and it is working properly. The tenant is able to get her email and browse just fine. I also have a Airport Express in the front house that extends the signal via WDS. I have a 24 inch Intel iMac 2.4 that is connected to the network and runs fine. When I check in the Airport utility the iMac can see both routers. I have a Power Mac G5 2.0 that has a Airport Extreme card in my studio which is behind my garage. It shows that it is connected to the network and at full strength but I cannot browse or get mail. I tried to run diagnostics but when I do it does not find my network. I also cannot find either one of the routers from the Airport Utility even though the Mac is about one room away from the main router. I tried renewing the DHCP. I also even uninstalled and reinstalled the Airport Extreme Card with no luck. I can see my network from the Status Bar where the Airport Signal Strength is but again...cannot find the routers in Airport Utility nor find the network within the Networking Diagnostics.
Any advise?

Little antenna is still intact. Everything looks good on that part. If I take it out the bars go grey. Yes this system was working fine with very good download speeds up to 1mb/sec (usually 400 to 700 kbps) up until a few days ago.

Buying an airport extreme card

hi guys,
i just bought an airport extreme card with my new imac 3.06 ghz...
i was wondering did i waste my money on this or what...
does the imac come with a wireless card or o... thnx

mohsan, Welcome to the discussion area!
Your iMac already has built-in wireless so you do not need that card.
BTW, this is the discussion area for the much older iMac G4.
Since you have an Intel-based iMac in the future you should post in the Intel-based iMac discussion area.

Can i use an airport extreme card in a powerbook 400MHz ?

i have an older powerbook 400MHz which is second hand and i have no manual for it. does anyone know if i can install an airport extreme card?
powerbook G4 Mac OS X (10.3.9)

wcslingsby, Welcome to the discussion area!
No you can not use an AirPort Extreme card with your PowerBook.
Your PowerBook G4 400 MHz requires the original AirPort card.

Will airport extreme card work with my emac?

I want to put an airport extreme card in my Emac. Please let me know if it will work in my machine. My Emac specs:
Power PC G4
CPU Speed: 800MHz
L2 Cache: 256 KB
Memory: 1Gb
Bus Speed: 100MHz
Purchase year: 2002 (before USB2)

According to:
http://docs.info.apple.com/article.html?artnum=107440
Only the eMac ATI Graphics model and USB 2 models could take Airport Extreme.
According to:
http://www.designedinca.com/macs/emac/may2003/800cd/
the ATI Graphics model replaced the August 2002 to May 2003 which was also 800 Mhz.
Thus your machine was the one before the Airport Extreme became available:
http://www.designedinca.com/macs/emac/aug2002/800/
So no, you can't put an Airport Extreme card in it. You can though get Airport Extreme speeds via a LAN capable WiFi access point via its 10/100 ethernet port.
You can also buy the original Airport card from:
http://www.a1acomputing.com/usorapaicam7.html
Message was edited by: a brody

Airport extreme card for eMac Ati

Is it possible to make an Airport extreme card react like a Base statrion.

You can use Internet sharing and make your eMac act as a base station. Unfortunately it has no options and therefore isn't as useful as a dedicated base station.

Airport Extreme card installed, eMac stuck on gray Apple screen at start-up

I just installed an Airport Extreme card on my eMac (USB 2.0). When I try to boot, it gets stuck on the gray Apple screen, with the spinning gray "spokes." The card is pushed as far as it will go into the slot, and the antenna is all the way in as well. When I take the card out, the computer boots up fine. I tried installing the software first, but it doesn't appear to be installed after it does the required restart for new software. I'm not sure if I have the software already...
At any rate, the biggest issue is that it won't boot past the gray screen. Any thoughts? (I have a version of Tiger, though I'm not sure exactly which because I'm sick of the un/install process at the moment, and am staring at the gray screen.)

The card is pushed as far as it will go into the
slot, and the antenna is all the way in as well. When
I take the card out, the computer boots up fine. I
tried installing the software first, but it doesn't
appear to be installed after it does the required
restart for new software.
Hi, I have a 1GHz eMac ATI and had a problem installing my Airport Extreme card as well. It would boot fine, but the card would not connect. It turned out that the card was not seated properly and maybe this is something for you to look at.
If you look at the Airport slot with the card and cover removed you will see the end of a black plastic guide bar on the right of the slot when viewed from the front of the machine. (Assuming the ATI eMac and USB 2.0 are the same in this regard) When the card and the aerial are fully seated home, the silver top of the aerial plug should be just about level with the front end of the black plastic bar, just a whisker or 2 sticking out. If it is more than this (more than say 1-2mm - 1/16th inch) then your card is not far enough in to be connected properly. Believe me I found this out through trial and error and there is not much difference between the right position and not.
It is not just a matter of pushing harder, you need to wiggle it slightly up and down and push firmly with 2 fingers, one on each side so that the force is evenly distributed. Mine needed just a smidgeon more force than what it took to slide the machine back - try it a little bit at a time. Put it up against a wall so it doesn't slide back, but don't apply excessive force. Part of the problem is that is hard to get your fingers in there to do the job.
Hope this helps.

My eMac can't find installed airport Extreme card

Hello everyone,
Having bought a netgear wireless modem for a wi-fi connection, I was told to install an airport extreme card on my eMac, which I did - several times. But the eMac says he can't find when I look for it, either in the internet setup or in the general information about the hard and software. I also installed the accompanying software. Why can this be ? Thanks for your advice!
eMac Mac OS X (10.4.7)

It's an eMac (USB 2.0) model. I'm not certain I should try to push the card in more ? Are those cards defective frequently ?
Which eMac do you have? You can use KB 86325, eMac: How to locate the serial number
and identify your model to determine which model
you have.
If your eMac is the "eMac (ATI Graphics)", "eMac (USB
2.0)", or "eMac (2005)" the AirPort Extreme card is the correct
wireless card.
If your eMac is the "eMac", it requires the original
AirPort card and is not compatible with
the AirPort Extreme card.
Assuming that your eMac is compatible with the AirPort Extreme card, one or more of
the following must be true if the eMac is not
detecting the card.
The card is not installed
correctly.
The card is defective.
The
eMac's motherboard is defective.
eMac Mac OS X (10.4.7) 1.25 GHz / 768 Mo DDR SDRAM

How to install AirPort Extreme card in eMac?

I just recently acquired a 2005 G4 eMac (the top-of-the-line model with the SuperDrive and 160 GB hard drive), and I am trying to install an AirPort Extreme card into it. Apparently I think the instructions must differ from this one:
http://support.apple.com/kb/HT2596
Since this is for the older AirPort cards.
I pushed the card in all the way, logo facing downward, screwed in the antenna, etc., but the Mac still won't recognize it! What should I do to get it working?

Numerous eMac users who installed Airport Extreme cards in the past have brought up that the Extreme card is a very tight fit in the eMac Airport slot, especially compared to the original Airport card. Often, the card appears to be fully seated, but is actually some fraction of a millimeter out. After seating the card according to all the instructions, you have to push hard on the edge of the card to get it to really seat all the way, hard enough to just start to push the 50-lb eMac away from you (don't try this with the eMac on the very edge of the table or desk!). I ran into exactly that putting an Extreme card in my in-law's eMac, and I had already read other's warnings; that may give you some idea how firmly you really need to push the card once it feels as if it's seated.

Airport extreme card with G4 ATI emac (1GHZ)

Similar Messages

Maybe you are looking for