Airport Extreme Flashing Amber - but internet connection is OK

I have the current generation of Airport Extreme, which has been working just fine, until tonight. It started flashing amber. My internet connection is OK, and in fact my desktop is connected to the internet thru the Airport Extreme via ethernet cable, so that pathway works (which rules out faulty cable between Airport and modem). But the amber light keeps flashing, and none of my devices that connect via WiFi can connect to the internet (to be clear, they can see my base station, but they cannot connect to the internet. The only device that can connect is my desktop, which again is connected to the base station via ethernet cable). I've done multiple power-cycles, and a hard re-set of the base station, same result. In Airport Utility, the error is "Your Apple Wi-Fi base station does not have a valid IP address", but assuming that this is the correct error (which I am doubting, since I am connected to the internet), there is no way for me to address it.
I have two Airport Express's on this network - needless to say, they are also showing up as problems in Airport Utility since their base station is amber.
BTW - I am running OSX 10.6.8 - OK, I'm a dinosaur. But just in case that was the problem, I tried to address this with the current Airport Utility from my iOS 7 iPad, but still no luck.
Any advice?

Thanks, landrefl. Airport Utility IS telling me that there is an error, and the error is ""Your Apple Wi-Fi base station does not have a valid IP address". But that's my problem - I'm writing this now because I am connected to the internet, through the wired connection thru my Airport Extreme. So, although it is telling me what it thinks is the problem (""Your Apple Wi-Fi base station does not have a valid IP address"), that a) seems to be incorrect, and b) I don't know how I can change or correct it anyway.

Similar Messages

Airport extreme flashing amber but still have internet

My airport extreme is flashing amber but I still have an internet connection. Should I be concerned?

When I opened Airport Utility, it gave me a message that firmware needed to be updated (to 7.6). However, clicking on continue or search for update (can't remember exactly what the option was), the utility searched endlessly for the update. I'd read on a previous discussion about unplugging the AirPort Extreme for 10 seconds. I did this while the airport was stuck in search mode. Sure enough that worked.

Airport Extreme Blinking Amber But Internet Working Fine Multiple Status Messages

I have Airport Extreme 5.6.1. It started blinking amber showing Airport did not have a valid Internet Address. I was concerned about with changing anything if I could still connet. Checked a forum and it suggested to go to sheck status and see the problem. I did and now I have a new mesage. No DNS server address. I am hesitant about doing anything because if I do and lose internet connection I am really up a creek without a paddle.

Just to update. I unplugged my modem for a short time. When it powered up the light was green on my Airport Extreme.

Flashing amber but is connected to the internet

flashing amber but is connected to the internet

Let's find out why that light is flashing, when it should be a nice solid green.
On your Mac....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click directly on the amber dot
A window will open to explain why the AirPort is complaining, along with suggested actions to remedy the issue.

Help setting up using my airport extreme to share my internet connection

I want to use my built-in airport extreme to share my internet connection with my PS3. I have a verizon aircard and have read on the internet that this can be done (but not necessarily with airport). I turned on internet sharing with airport and my ps3 reads my connection and obtains my ip address, but then it says could not connect to internet due to DNS server error.
Could someone run me down the process step-by-step so I can see what I'm doing wrong? Thanks for your help.
P.S. I have a iMac running on leopard if that matters.

ll959reds, Welcome to the discussion area!
Unfortunately the Internet Sharing provided by OS X does not provide nearly the configuration possibilities as even a very inexpensive wireless router.
Also if the firewall is enabled on the iMac, it applies equally to all ports including the AirPort (wireless) connection to the PS3. Therefore the firewall will block many of the requests from the PS3. To solve this issues, you would either need to disable the iMac's firewall or configure the iMac's firewall to allow connections via the AirPort side.
A much simpler solution is to use a wireless router instead of your iMac to provide the connection for the PS3.

Just purchased Airport Extreme ac and lost internet connection 3X. Reset to factory settings and worked for 2 days then lost connection and remedied by unplugging power supply. Anyone else having problems?

Just purchased Airport Extreme ac and lost internet connection 3X in less than one week. Fisrt time, reset to factory settings and fixed problem. Has occurred 2 additional times and connection re-established by unplugging AP extreme. Anyone else having these problems? Do I have a bad router? Thanks.

I definitely think this is a Mavericks issue. My iMac running Mavericks is the ONLY system in the house that drops the network randomly while all other systems never lose the network. No idea how to resolve this, but here is the workaround I'm posting:
I've had the 'network drop' issue with my Airport Extreme for the last 2 months. It reconnects when I pull the ethernet cable and plug it back in. I've tried downgrading the AE firmware, resetting to factory, etc. Nothing worked. I finally threw in the towel and created a script that monitors my network connectivity and restarts my interface if it senses it has dropped:
#!/bin/ksh
while true
do
yup=`ping -c1 -t2 www.google.com|grep from`
if [[ -n $yup ]]
     then echo "Internet is connected!"
else
        ifconfig en0 down; ifconfig en0 up
        echo "Down at `date +%m%d%Y%H%M%S`">>./dropped.out
fi
sleep 5
clear
done
I know its a workaround, but its saving me the headache of constantly pulling my cable and putting it back in!
Good luck!
-Mike Gray

AE Flashing Amber (Status: Internet Connection) but Internet Green

Apologies if this has been asked before, I couldn't find an answer.
I'm on an AE with a Motorola SB6120 modem, paying for Comcast service.
My AE worked fine two weeks ago when I was on Centurylink at another address.
Problem:
AE is flashing Amber.
Status says "Internet Connection", yet...
AirPort Utility tells me that Internet is Green. Plus, I'm typing this through my wifi/internet, so it appears I'm online.
The other major issue is that none of my other wifi-capable devices can connect to my network. Only my MacBook. Not my iPhone, nor my wife's Dell laptop or Droid phone, nor my Nest thermostat. All can see the network, but none can connect to it. They either time out or, in the case of the Dell, say they can't find an IP address.
I have factory reset the AE, unplugged and re-plugged everything in every order I can think of. I've shut down my computer a half dozen times.
When I factory reset the AE, it was green/green for a moment, then went back to flashing Amber. At that point, it had two "Status" issues: Internet Connection and DNS Servers. I entered the DNS default: 75.75.75.75 and 75.75.76.76. DNS "status" went away, but "internet connection" remains.
When I click on the AE icon on the AirPort Utility, it gives the network name I chose, IP address is blank, the serial number is there and the version is 7.6.1. It lists one wireless client.
If I drill deeper, the "internet" menu says I'm connected using DHCP. IPv4 Address is blank. Subnet Mask is 255.255.255.0 and Router address is 192.168.100.1. I gave the DNS servers above, and IPv6 servers and domain name are blank. On the wireless menu, the network mode is "create a wireless network", the network name is correct, it's WPA2 Personal security. On the "Network" menu, the Router Mode is "Off (Bridge Mode). All else is greyed out.
If anyone can help, it would be greatly, greatly appreciated. I am at wits end, my wife cannot connect to our home network, and I am questioning why I bought an AE when every other router seems to work better.
Many thanks.

Vagabond0079 wrote:
I entered the DNS default: 75.75.75.75 and 75.75.76.76. DNS "status" went away, but "internet connection" remains.
Not sure what you mean by default, as those are Google DNS addresses. The default would be to not enter anything and allow Comcast to provide them. In a perfect world Comcast would provide you with the fastest, most reliable DNS service, but that is often not the case, which is why there is OpenDNS, Google Public DNS, etc. In any case, that's not your current problem and now that you have that part working you can decide if that's what you need later.
On the "Network" menu, the Router Mode is "Off (Bridge Mode). All else is greyed out.
There's the problem. It should be "Share a public IP address". Bridge Mode just short circuits the router, which is why only one device is connecting.

PLEASE HELP!!! AIRPORT EXTREME IS GREEN BUT NOT CONNECTING TO INTERNERT!!!

Please, I'm begging of fellow man, women and children to help me figure this out!
What Happened:
I had my Internet and everything working before I went to work at 3 PM. My girlfriend got home around 4 PM and all of a sudden the my Internet was not working. I had to call my ISP, Comcast, and we had tested Internet connectivity which worked perfectly fine which is how I am typing this now. After that, I looked up some things that would remedy the situation. Power cycling the modem for minutes, seconds and hours. Also, I have tried to plug both the modem and router without plugging any Ethernet cord in to both of them, wait for them to power up, hook up the Ethernet cord and nothing. I have done factory resets on both the modem and routers and created a totally new network to see if that was the problem and noting. I have also changed the IP addresses, Subnet Masks, Router numbers, DNS servers and Domain names and nothing. I was stupid and did not get a protection plan on it, and my warranty JUST expired a couple of weeks ago, so I have barely had this router for a year. As all indications go, it is saying that it's connecting to the Internet, but when I go to my Macbook Pro and check the system preferences it's saying its connected to the airport, but when I do the assist me function and go to diagnose or assistant and test everything, the Internet and Server are yellow and everything else is green. I DON'T KNOW THE ISSUE!!!
Hardware:
Modem - Motorola Surfboard: Model SB6121
Router - Apple AirPort Extreme 802.11n Wi-FI
Any and all advice would be greatly, greatly appreciated. I do not want to have to purchase a brand new router after just purchasing this one last year for over $150. I'll be eagerly awaiting your help. Thank you in advance.

@Mark Scott, are you referring to my cable modem or the apple router. I'm currently connecting to the internet just fine connecting the ethernet cable to my Macbook Pro laptop directly and having everything connecting just fine. Its when i try to connect wirelessly to the AirPort Extreme router is when I am unable to connect. If you were referring to the connecting the router directly to the computer and seeing if there is an internet connectin, I don't think that would help anything at all. Please let me know if this is what you meant and I will try it anyways.

Airport is flashing amber, but I can't fix it

Hello all,
My Airport Express, which I use in a WDS as a music relay, is flashing amber (which means that it can't connect) and whenever I try to access it using Airport Setup Assistant or Airport Admin Utility, it says that it can't connect or just hangs. Airport Setup Assistant gave me this message:
http://i198.photobucket.com/albums/aa187/adam_0/Picture1.png
There is absolutely no way that I know of to access it from my computer, and unplugging it and replugging it back in doesn't work. What is wrong???

When I went back to try to directly connect to the AX, I noticed that the light was solid amber, not flashing anymore. Supposedly that means that it's starting up, but it's been that way for a while... I have a location specifically for the ethernet connection to ABSs, but Airport Admin Utility couldn't detect any AXs. So is something wrong, or am I not able to connect directly to the AX?

Airport Extreme keeps dropping the internet connection to my mac

Hi, for a while now my airport extreme has been dropping my internet connection to all my mac computers. Its just the internet that drops i still have connection to the airport because i have a external HD hooked up to it and i can still access it when the internet drops. I dont think it has anything to do with my macbook because i have taken it friends places that have a wireless router and it never drops there. The airport usually drops when im on youtube watching videos. It always seems to drop when the video is less then half way done loading. I would extremely appreciate the help. Thank you for your time.

My problem is gone!!!!! I found what my problem was! So... after many days of being frustrated with the dropping. I phoned apple. They said it might be the service provider. Ok, well Apple said that some internet service providers don't like it when people use wireless routers. Because of people stealing internet and such. And since there is a lot of computers running off of my wireless router there are a lot of IP addresses connected to the internet opposed to just one set if you were connected to one computer by ethernet. So after my chat with apple, I phoned my internet service provider, Tbaytel. I told them that i have been losing internet connection for 5 months, and i would like it they would tell me what's going on. I told this guy what apple told me about the IP addresses always changing and he started to laugh at me and he told me that they don't know what there talking about.. After they told me to do the stupid shut everything off... now turn it back on.... is that light flashing?? Ok... now plug in the router.... All ******** basically. So after this guy being all confident telling me what to do and thinking that the problem will be gone, we wait 5 min and the internet drops again. So i tell him. There was a long pause....Ok ill try and do a reboot of the connection. He does this reboot thing and i have connection again. It doesn't drop. 3 hours later it drops again... So the problem came from the internet service provider, which was not a very good one. 2 months ago we swithed to SHAW and guess what? We haven't dropped yet!

Airport Express flashing amber, but shows normal in airport admin utility

I just replaced a Microsoft wireless router with an Airport Extreme base station. I've had 2 airport express stations on the old wireless network working fine with solid green lights - 1 streams airtunes and the other is a print server. I installed the extreme base station and now the 2 airport express stations appear as normal / working in the airport admin utility but have flashing amber lights. the print server actually works - I can print. The airtunes streams, but it cuts out every 5-10 seconds. Can't figure out how to get rid of the flashing amber and can't find the error since the airport admin shows them as green and working normal.
Any ideas??

Hi ...... I am having the same problem but am having difficulties finding out why.
How did you solve it ?
Many thanks in advance

Airport Extreme Cannot see Live Internet Connection from Cable Modem

Hi,
When I run a cable directly from my cable modem to my MacBook everything works fine. In fact, that is how I am connected to the Internet right now.
However, when I run the same cable into my Airport Extreme (AE) and then connect my MacBook to the AE (wired or wireless), the AE reports a problem connecting to the Internet. This is a new situation as everything has been working fine for months. I have changed nothing in this set-up for it to stop working.
I can only assume the at the AE is broken: the Internet connection is live, it was working fine for months and then stopped working. Is there anything I should try before I throw the AE in the garbage?
Thanks in advance.

Welcome to the discussions!
It appears as if you may not be aware that cable modems must be completely reset whenever the device that they are connected to changes. The reason for this is that the cable modem "remembers" the device that it has been connected to. In your case, it's "remembering" your computer and looking for it when you plug it in to the AirPort Extreme.
You need to make your modem "forget" your computer. Here's how:
o Push the reset button on the modem if there is one on your modem
o Power the modem down immediately after you push the reset button
o Pull the battery in the modem if it's easily accessible
o Leave the modem powered down at least 20-30 minutes (Some ISPs take longer)
Power down the rest of your network as well.
After the power down period, start the modem first and let it run 3-4 minutes by itself
Then start the Airport Extreme (you may need to "hard reset" the device again to start over on the configuration) and let it run a few moments
Then start your computers one at a time
Please post back on your progress. Remember, if you need to connect your computer directly to the modem again, you must reset the modem again because it will "remember" the AirPort Extreme if you have reset it correctly.

I have an airport extreme for my main internet connection, an express to listen to music on my home theatre, another express to extend the network upstairs, and one more express for my wireless printer. whats the best way to setup the express stations?

So basically I would like to know if its best to have them setup on "join a wireless network" or "extend a wireless network"
Obviously the one I use to extend the network is setup that way, the other 2 are set on "join a network"
is this the optimal configuration? or should I have them all on "extend a wireless network" ?

There is really no "best" setting here for the AirPort Express devices. If you need more wireless coverage in the area where an Express is located, then it makes sense to configure the Express to "extend" a wireless network.
If you already have good coverage in an area where an Express is located, then the "join" configuration makes sense.
I've yet to meet the first user who felt that he/she had too much wireless signal coverage in their home, but you never know.

How do I connect Airport Extreme to U-verse Internet Gateway: Motorola Model NVG510

I tried to set up a new network with the Airport Extreme and get no Internet connectivity from the AT&T gateway. The Extreme network sets up fine and I can access it from all my devices, but no Internet.
What am I doing wrong?
Thanks,
Mick Jones

It will only take a minute to check the Ethernet cable. Just connect it from a LAN <-> port on the Uverse gateway to the Ethernet port on a computer. Turn off the wireless on the computer and see if you can get a good Internet connection that way.
If you can, great. You cannot, then you either have a bad Ethernet cable or the port on the gateway may not be working correctly.
Power up the AirPort Extreme for a few minutes
Then, hold in the reset button on the AirPort Extreme for 10-12 seconds and release
Allow a full minute for the AirPort to restart
Connect the Ethernet cable from a LAN <-> port on the Uverse gateway to the WAN "O" port on the AirPort Extreme
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on Other WiFi Devices
Click AirPort Extreme
The utility will open up automatically, take a minute to analyze things, then suggest that the AirPort will be configured to create a new network. The window will look like the example below, except that you will see an AirPort Extreme instead of an AirPort Express.
Network Name......type in a short, simple name that you want to call your wireless network
Base Station Name.....type in a short, simple name that you want to use to identify the AirPort Extreme
Password......type in a password that will be used for both the Base Station and Wireless Network
Verify the password
Click Next
You should have a green light on the AirPort Extreme in a minute or two, and you should be able to log on to the new network and get an Internet connection.

Just bought new AirPort Extreme did everything on manual and light still flashing amber , it is connected to an Arris TM822 from optimum cable company , help please

Just bought new AirPort Extreme did everything on manual and light still flashing amber , it is connected to an Arris TM822 from optimum cable company , help please

Any luck with the suggestions mentioned by Bob Timmons?
I am having pretty much the same issue.
Got a new modem Arris SB6141 and a new Airport Extreme ME918LL/A. Activated with my ISP (Comcast). Worked with a savy tech who knew the modem and Airport Extreme. Ensured all items were correct from the ISP side.
I follow the instructions as indicated for Airport Extreme by it fails to detect the internet and dns servers. Comcast suggested I call apple. Reading posts above I will:
-Reset the airport extreme
-Unplug the modem for 30min
Airport Utility 6.3.4 (634.17)
Airport Extreme ME918LL/A Firmware Version 7.7.3
MBP - Yosemite Mid 2012
Appreciate the assistance folks.

Airport Extreme Flashing Amber - but internet connection is OK

Similar Messages

Maybe you are looking for