Airport Extreme in XP

Just installed Airport Extreme without a problem, but I can't get it to work in Windows xp Boot Camp). The Airport Base Station shows up in the available networks, but Windows can't connect and reports a 'may be out of range' error (its not out of range). The Airport Utility in XP also can't locate the Base Station.
Anyone have this problem?

http://discussions.apple.com/thread.jspa?threadID=859336&tstart=0

Similar Messages

  • How do I use my airport extreme with my FIOS router?

    How do I use my AirPort Extreme base station with my FIOS Router to extend my network?  I have hard disks connected to my AirPort Extreme and would lik to access them.

    Probably can't answer all your questions - but.... I use a Linksys (wired and wireless) router as my primary entry point for FIOS. I use a Time Capsule and an Airport Express as a common wireless connection. So I have two visibile wireless networks and use them both depending on where I am in the house. Both the TC and AEx can be seen either wirelessly or wired from the entire network. Note - the Linksys provides all the DHCP - you set the apple routers as "bridge mode."

  • Help setting up Open DNS with new airport extreme

    I cant seem to get Open DNS to work with a new airport extreme. The status says I am not using Open DNS and its not filtering anything. I have followed the exact steps for set up listed on their website, checked the dns settings, cleared both caches and restarted the computer, modem and router with no success. I set the airport up in bridged mode, although I tried the other option under setup, but not sure what I was doing? I picked up this router because I wanted easy set up and the apple store assured me it would work with Open DNS. Oh, and I also downloaded the latest firmware update on the router. Can anyone help me with the settings or what else I need to check?

    Sorry, I am not familiar with this product, so I checked online to pick up some information.  Here I am referring to the information found here:
    http://www.dslreports.com/faq/6096
    I found that your device is mentioned as follows in the intro under Section 1 of this document:
    The BellSouth supplied Westell 2100, 2200 and 6100 models (Models A90-210030-04, B90-220030-04, and B90-610030-06/C90-610030-06, respectively) share many features and functions.
    Next, I am referring to the information under Section 2, under the heading of Standard Default Mode Connection (separate hub or switch present).  Unless you have changed the configuration on the Westell, this is how your device is operating. In this mode, the Westell device is acting both as a modem and router in one unit.
    So, an attached router (AirPort Extreme) must be configured as a switch to work correctly. That is what Bridge Mode is....the AirPort Extreme is operating as a switch when it is in Bridge Mode (which would be the correct setting to use when the Westell is set to its Standard Default Mode).
    Any changes that you want to make regarding DNS settings would need to be made on the Westell device, since it is acting as the main router on your network.
    In Bridge Mode, the AirPort Extreme simply passes that information through to its connected devices. You will not be able to make any DNS related changes on the AirPort Extreme since it receives that info from the Westel device. Some service providers force you to use their DNS servers, so you might want to check with Bell South or AT&T for more information in this regard.
    If you want to be able to configure the AirPort Extreme as the main router on your network, and instruct it to use the DNS information that you want, you will need to refer to the section under the heading of Bridged Ethernet Mode ( separate router present).
    Please note that the first item under this heading specifies that "This is the preferred configuration when using a separate external router..." (which would be the AirPort Extreme in your case)
    So, it appears to me that this would be the way that you must reconfigure the Westell device to allow the AirPort Extreme to function as the "main" router on your network. In this type of setup, you will be able to enter the DNS information that you want to use under the setup for the AirPort Extreme and it will act as you instruct.
    The AirPort Extreme would not be configured in Bridge Mode for this....it would be configured to "Share a public IP address".
    The next item in the article specifies that you "Must use a PPPoE client on the Router." This means that the AirPort Extreme would be configured to Connect Using = PPPoE as follows:
    AirPort Utility - Manual Setup
    Click the Internet icon
    Click the Internet Connection tab
    Connect Using = PPPoE
    You would enter your user name (probably your email address), password, etc in this area. Leave the Service Area box completely blank. Set Connection to Always On, and Disconnect if Idle to Never
    Click Update to save the new settings. Power off the Westell device after this and then restart it so that it will pick up the new information that you have programmed into the AirPort Extreme.
    I want to stress that this is how I would try to configure the Westell and AirPort Extreme. But, as I said, have not used a Westell device, so I cannot say that this will work correctly for you.
    It might be an excellent idea to contact Bell South or AT&T Support to ask for their opinion on this before you decide to change the configuration of the Westel device and the AirPort Extreme.
    This type of thing can be intimidating for users, so you might elect to use the services of someone like the Geek Squad at Best Buy, or a similar service from a local computer firm. Perhaps the Apple store could help as well.
    If it is not critical that you use Open DNS, you might want to simply leave things "as is", with the AirPort Extreme in Bridge Mode.

  • How do I open the same ports on an Airport Extreme Base Station for multiple computers at the same time?

    As the title suggests...
    I have a mix of five Mac and PC's at home using an Airport Extreme Base Station as the router.   I need many ports opened on the AEBS for all of the computers- not just one computer.  (for example: three people want to play TF2 on Steam at the same time; each machine needs the correct ports open on the router).   Port forwarding  only allows me to forward a given port to a single IP, yet I need that port open for five differnt IP's, all at the same time. 
    How do I do that on an AEBS?
    In the same way, I have a small office of four iMacs using an old airport with the same exact issue.   I would like to be able to connect to all of them remotely with Apple Remote Desktop, but the port forwarding on the airport only allows a port to forward to a single IP.   I want to be able to tunnel into the office network and log onto any machine behind the Airport extreme... not just a single IP.    I currently have it set up where I can tunnel into the office from my house, I can find the one machine that the port forwarding has been assigned to, I can log on and everything is just fine... with one machine.    How do I open the firewall for the other machines? 
    TL,DR version:  How do you open ports on an Airport Extreme Base Station instead of forwarding ports?   Forwarding ports doesn't work for multiple IP's.  

    You can open a single or multiple ports to a single device or different ports to different devices, but you cannot open the same port to multiple devices via the AirPort Utility for the Apple routers.

  • How do I add an airport extreme to a cable modem with only one ethernet port, while keeping that port connected to my Mac?

    I have a mac pro connected by ethernet to a cable modem via ethernet.    There is only one ethernet port on the modem.   
    I want to keep the Mac connected via ethernet for speed.    Is there a way that I can add an airport extreme to this set up - for my ipad and roku, and for guests to use - or do I need to buy a router to put between the modem and the mac?
    If I need a router, what kind?
    Thanks.

    The modem connects to the WAN "O" port on an AirPort Extreme router.
    The Mac Pro connects to one of the three LAN <-> ports on the AirPort Extreme router.
    Or if you do not need the ability to connect a hard drive to the USB port on the router, you can save a bit by using an AirPort Express.
    The modem connects to the WAN "O" port, the Mac Pro connects to the LAN <-> port
    Either the AirPort Extreme router or AirPort Express router will allow up to 50 wireless device to connect.
    There are many other wireless modems offered by other manufacturers as well.

  • Airport Extreme no longer recognizes or provides internet to wired devices

    Not sure if it was the power outage or an update that is the problem; but, I had a 5th generation Airport Extreme as the center of my home network with a solid connection to the internet for both my wired and wireless components.  A few days ago, after a power flicker (all components on surge protectors) my wireless internet would not stay connected more than 45 seconds before dropping and oddly, none of my wired components we showing up on the network or getting an internet signal from the AEBS.  After two hours with my ISP technical support personnel we deduced that the problem was the AEBS and the modem was fine.  I bought a new AEBS yesterday (the new long cube one) to use until my appointment to have the 5th gen looked at.  Plugged that in and instantly my wireless network came back up - rock solid.  However, anything I connect directly to the AEBS via ethernet does not get an internet connection or show up in the network.  I searched for two days in these forums for a similar problem - but, have gotten nowhere.  I used my wired connections for internet phone service and really need to get this fixed soonest.  Much thanks for any help anyone can throw my way.

    I would find it odd that you would have a replacement AirPort and still not have Ethernet connectivity ... but, of course, anything is possible. The DHCP service on the AirPort provides IP addresses to both wired and wireless clients by default so it shouldn't work for either if there was something amiss with it.
    At this point, I would suggest that you try the following:
    Perform a "factory default" reset on the AirPort. After it resets it will default to its "out-of-the-box" configuration which is a wireless Internet router that will broadcast an unsecured wireless network with a Network Name of something like: Apple Network NNNNNN.
    Without making any changes to the AirPort, try connecting any of your wired devices to it. If it still does not get the proper IP address and network connectivity I would suggest that you try performing a complete power recycle of your networking hardware. Please check out the following AirPort User Tip for details.

  • Time machine can no longer see USB drive connected to airport extreme

    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?

    bradleydad wrote:
    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?
    what exactly do you mean when you say that TM doesn't see the drive? do you mean you can not choose it as the destination TM drive in TM system preferences? do you see the airport drive mounted in finder? if yes, connect it directly to your mac and repair the disk (not permissions) with disk utility. then move it back to AEBS. see if that helps. if not try the following terminal command
    defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1
    it should not be necessary with drives connected to AEBS but it might work.

  • USB HDD not ejected properly...no longer recognized by Airport Extreme

    I'm hoping someone can help.  I'm quite desperate as all of my DVDs are on this drive.
    I have a 2 TB WD USB harddrive that I connect to my airport extreme to use as my iTunes storage.  Up until 2 days ago there have never been any issues.  I was messing around, cleaning up around the router and hard drive and the USB cable was pulled out of the harddrive.  Now when I plug the USB cable back into the drive, it is not recognized in the Airport Utility.  I installed an older version of Airport Utility and it shows the volume, but I cannot do anything with it.  It is also not recognized in finder.  If I plug the drive directly into my MBP, it mounts fine and is totally accessible.  What could have meesed up with the drive?  I have another 1TB drive that I tried and this is recognizable in Airport Utility and finder along with a USB stick I have laying around.  It is only the drive that has all my stuff on that is no longer usable.
    If anyone has any suggestions I would be very greatful.
    For what it's worth, I've tried everything I can find on here and the web short of reformatting the entire drive.  I can't do this as I'll lose all my "stuff".
    Thanks in advance.
    Marc

    This is a user to user discussion area. So it is unpredictable as to when someone with a suggestion will respond to your post. An hour in the middle of a work day isn't a long time.
    Since the card is recognized, there isn't anything wrong with that side of the card. If the card isn't receiving a signal, either the RF side of the card has failed, the antenna wire isn't connected properly, or the antenna in the PowerBook has failed.

  • Airport Extreme Printing Problem with HP Deskjet.

    Hello ... I wonder if any helpful folks can assist me with my printing problem? I am using Tiger on a new Intel imac with a HP Deskjet 960C. This printer is listed as having the latest drivers included within Tiger and works perfectly when connected via USB so my problem I guess is not with the software....I have disconnected everything and plugged everything back together again. I also deleted the printer from the printer list within the Printer Setup Utility application.... The imac recognisies the printer and upon pressing the print button everything feels as though its just going to work. The blue barber shop scroll appears but the printer fails to kick into gear and I get the big red exclamation mark appearing in the status box .... I would really love to try and sort this annoying error ... Any ideas? Thanks. Book G4   Mac OS X (10.4.4)  

    Hello jds17. Welcome to the Apple Discussions!
    Unfortunately, not all USB printers are compatible with AirPort base stations.
    Take a look at one of these iFelix Unofficial AirPort Printer Compatibility links, depending on which AirPort base station you have:
    o 802.11g AirPort Extreme Base Station (AEBS) or AirPort Express Base Station (AX)
    o 802.11n AirPort Extreme Base Station (AEBSn)
    If your printer isn't listed, it doesn't necessarily mean it won't work, but simply that it has not been verified. iFelix also provides the following workaround for printers not on the list that would certainly be worth a try.
    Also, you may find the following Apple article helpful.

  • Internet - AirPort Extreme (b/g) - Time Capsule - File Server

    I've got a small office network where files are served off a Mac mini, and iMacs connected via 802.11n wifi to the wired mini via Time Capsule. I have a spare AEBS (b/g) that I was thinking of setting it up for iPhone and guest access of internet. To keep the mini and iMacs secure, the set-up would be:
    Internet -> AirPort Extreme (b/g) -> Time Capsule -> Mac mini and iMacs
    The only issue I'm contemplating - the slower Ethernet ports on the Extreme - which I don't think is a problem for connecting to the Internet. Is there anything else I should be concerned about regarding network performance?
    Thanks in advance for the collective wisdom!
    Message was edited by: openarchitecture

    That would work. The Ethernet ports on the AirPort Extreme base station (AEBS) is faster than your internet connection so you shouldn't have a problem.

  • Connecting HDD to Airport Extreme causes orange death light...

    I am in a small office network with mix of pc and mac (7 pc's, 1 iMac, 1 wireless iMac, and 3 wireless macbook pro's). Internet connection comes into building directly to airport. Airport then feeds a couple of systems directly and a Dlink 24port ethernet switch which connects all other hardwired network connections.
    I just purchased a Seagate Freeagent Desk 1.5TB external USB2 drive to be used as a network storage drive (not with time machine just grabbing and dumping files for interoffice sharing). Removed preloaded software and formatted fat32. Disk will be mounted and recognized when connected to any mac directly. When connected to the usb port on the airport extreme it begins to initialize and then bombs. Airport gives the orange death light and there is no connectivity to the router for all (ie internet connection, etc.) When you unglug the HDD the router reboots and then goes back to green light of peacefulness. What am I missing? Setting? Order of connection? Not hitting it hard enough on the ground with a large 10lb sledge hammer? Help me out...

    you may need to restart the AEBSn with the drive plugged in.
    since it might have been long since the AEBSn was restarted and anything else attached to it.
    or a restore to factory settings...
    i know not the best you want to hear, it should just work.
    make sure all the AEBSn updates are there...etcetc
    i was having this problem the past month or so and it started working again flawlessly after a few restarts.

  • I'm having a hard time setting up my external hard from with my AirPort Extreme and Time Machine Backups.

    I have been using a Mac Mini with an external hard and Time Machine.  I bought an Airport Extreme and have had problem setting up the hard drive using the USB port on the Airport Extreme.  I also just recently bought a Mac Book Air and hope to have both computers back up to the external hard drive using Time Machine and Airport Extreme.  I have been using the optical drive from the Mac mini to load programs into the Mac Book Air.  I think I'm just getting confused in Finder.  I am just not seeing the hard drive.  I ended up plugging the hard drive back into the Mac Mini and that is work fine again.  How do I setting the external hard drive up to the AirPort Extreme and use for both computers?  Or at least to start with the Mac mini.

    It's critical to understand that Time Machine (TM) stores backups differently between local and network drives. That would mean the TM backup on your locally attached USB hard drive will not be directly useable when it is connected to the AirPort Extreme Base Station (AEBS). There is a way to copy a local version to a network version, but it is not fool-proof. When you do connect this drive and point TM to it, TM will start a brand new backup, leaving your existing backup as is.
    If your current backup is critical to you, you may want to consider getting a second USB drive to attach to the Extreme and use your existing one as a backup ... or use TM's multi-backup process to backup to more than one destination drive alternatively.
    So, at this point, you may want to make a decision on how you want to go forward to help provide a solution for you.
    To directly answer your question, when you go to select a destination for a Time Machine backup, the drive(s) that show up under "Backup Disks" are those that TM already recognizes and has backed up to. Those listed under "Available Disks" are drives (either local or on the network) that TM can back up to.

  • I am unable to see my Airport Extreme/Express on my MacBook via Airport Utility

    I have two issues:
    1. I am unable to see my Airport Extreme and my Airport Express via my MacBook Air's Airport Utility when I scan for Base Stations. However, the computer is happily connected to the wireless network of my Extreme (the Express is used to extend range)
    2. I am unable to see a HDD that is connected via USB cable to the Airport Extreme.
    Any suggestions welcome.
    Thanks

    Further info:
    Setup
    MacBook Air running OS X 10.5.8
    AirPort Extreme Base Station
    AirPort Express used to extend range
    AirPort Utility v5.5.3
    The MacBook Air is actually connected to the wireless network provided by the two AirPorts!
    Oddly, I see both AirPorts just fine when using my older PowerBook G4 with an older version of the AirPort Utility.
    In addition, I cannot see the external HDD connected to the AirPort Extreme Base Station, and my wireless printer (HP D410a) suddenly stopped working via the MacBook Air. However, it works just fine from my iPhone, which is connected to the same AirPort Extreme/Express wireless network.
    Recently, at the request of Sky Broadband, I switched to fixed IP addresses instead of DHCP, as I was having issues with the DHCP set-up.

  • How to connect old aiport express to my new Airport Extreme? My Ipad says "base station e5713b cannot be configured" and my AirPort tool on my PC will not permit me to add my new Airport Extreme network (no network names to choose from)

    How to connect old aiport express to my new Airport Extreme?
    I have a PC running with Win7 and just replaced my Jensen With a brand New Airport Extreme.
    I have set up the Airport Extreme to the internet, Iphones and Ipads and it work as it should.
    I have downloaded latest Version of Airport tool on my PC. In addition i have downloaded the airport tool for Ipad.
    I have reset one of my airport Express and it now shows up both on the Ipad and on the PC airport tool.
    My Ipad says "base station e5713b cannot be configured."
    I have wired the airport Express to my Ethernet to be able to "see it" on my Airport tool.
    My AirPort tool on the PC will not permit me to add the airport Express to my new Airport Extreme network (no network names on the drop-down list to choose from). I wished for an easy set-up, but nothing seems to be plug and play as the Commercial says.. can you please help me?
    Sigve

    Hi
    Thanks for Swift reply.
    Yep - I in fact have two A1088 and one A1264
    I actually bought the new router because the Jensen
    router always lost connection to the Airport Express after some hours or days. I
    always needed to restart my Jensen to play music and that was driving my wife
    mad. The hope was that the Extreme should fix this. Both A1088 have been set up
    to only stream music to two of my stereo amplifiers from my PC’s Itunes library.
    Are the A1088 now useless?
    The A1264 has been set up to feed internet into a Denon Reciever that needed Ethernet cable.
    Please advise
    Regards
    Sigve

  • How to set up my airport extreme to share my net connection. i have a ethernet cable from my isp which when i use in my mac, i have to enter username

    I access net through ethernet cable from my isp. so i just plug in the cable in my mac and in the browser it put the username & password. now i want to use my airport express to create a wireless network so i can access net from ipad and mac simultaneously. when i use airport express both my mac & ipad gets connected to airp exp but each of them ask for isp's username and password. i can only login from either one of them and access net in that one only. Pls advice???

    To allow your Mac to "see" the HDD attached to an AirPort Extreme Base Station (AEBS) that is configured as a bridge, just be sure to assign a static Private IP address to the AEBS. By default the AEBS is a DHCP client and will get a dynamic IP address from the upstream router that is acting as the DHCP server. Since this address can change over time, it would make it more difficult for network clients to find the HDD.

  • How to set-up new Airport Express to extend range of Airport Extreme

    Purchased a new Airport Express to use it as a range extender on existing home network with an operating Airport Extreme base station. While I've read instructions, I'm unclear whether the Express needs to be connected by ethernet cable for its initial setup, or can I simply plug it and initialize it wirelessly onto the same household network? (I've tried the latter but without success).

    to edex67 and Bob Timmons:
    My objective is to extend the wireless range of the Airport Extreme base station wirelessly - so I do appreciate that the Airport Express would needsto be located haflway between the base station and the "dead zone" area.
    The suggestion of using a Powerline ethernet connection to the Airport Express has merit (especially as I have one available).
    I continue to use OSX 10.6.8 - does this affect my set-up in any way?
    My problem had been - and remains - how to configure the Airport Express in range extend mode - I did click these boxes on both the Extreme base station and the Express, however the Express still has flashing amber lights and error codes - one indicating no internet availability on the Airport Express.

Maybe you are looking for