Airport Extreme missing IP address

I have never had so much trouble with anything from Apple before. Then again I am not good at networking. I have set up the AEBS as per the instructions using Airport Utility but I get an error saying the IP address cannot be found. At the moment I am using an Alcatel modem which is shared through a Belkin wireless router. I've got 2 macs and a pc linked to it via ethernet and a laptop and another imac G4 linked to it wireless. I upgraded to the AEBS to try get a better signal strength around the house and to share the printers. However, I am making no head way at all. If some one knows of the exact fix, please help. Thanks

Hello The Swagman. Welcome to the Apple Discussions!
Is your intent to replace the Belkin wireless router with the new 802.11n AirPort Extreme Base Station (AEBSn), or as an addition to the Belkin?

Similar Messages

  • Airport Extreme No IP Address

    Airport Extreme No IP Address & Self Assigned IP Address Issue, RESOLVED:
    Re: Airport Extreme IP Address Issue
    After hours of trying everything else, this worked!!!
    From: Comcast Networking/Router/Wifi Gateway:
    Re: Airport Extreme IP Address Issue
    11-20-2012 07:11 PM
    MyComputerGuyJo:
    I just wanted to add what Apple Support walked me through. Worked perfectly. Similar to some of the posts here. This assumes you have finished the setup of the Airport using DHCP to obtain the IP automatically from Comcast and it says the IP is invalid.
    Power off\on Sequence
    1, Power off Comcast Modem. Remove Battery back up, if it has one. Disconnect the coax cable.
    2. Power off Airport Extreme
    3. Let both sit for 3 minutes.
    4. Reconnect coax cable to Comcast modem and replace battery and power up.
    5. Wait a minute or two to make sure the Comcast modem is completely up and then Power on the Airport Extreme.
    (When AP asks for DNS, Type in both addresses below)
    Re: Airport Extreme IP Address Issue
    11-01-2012 03:07 PM
    Freyfisher: I had the same problem whenn I switched to the Airport Extreme yesterday.  Here is what I did:
    1:  uplugged modem for 30 sec. and detached all ethernet cables.  Plugged back in and reattached airport extreme cable after all lights were solid on the modem. Then, I went into Airport Utility and selected, "Base Station"> "restore default settings".  Then" Base Station"> Restart.  Then go through setup assistant again. If no luck, try setting IPv4 to 10.0.1.2, subnet to 255.255.255.0, router to 10.0.1.1. IPv6 set to OFF if having trouble.  DNS adresses: 75.75.75.75, 75.75.76.76, search domain hsd1.ST.comcast.net where "ST" is your two-letter State abbrev. Hope this helps someone....

    I have also looked through other threads about this same problem, but none of the solutions (e.g. posts by Tesserax, followed to the letter) so far have worked.
    Here are other things I have tried:
    1. Called Cox to have them reset my modem, internet works through Ethernet directly from the modem
    2. Downgraded AEBS firmware to 7.6.1 (oddly enough, now I cannot for the life of me update the firmware back to 7.6.4, always says cannot connect to update server)
    I ran through the various solutions from this thread: "No DNS servers" and "Internet connection" problems with Comcast?
    Still getting that pesky blinking amber light.

  • How do i find my airport extreme's ip address

    How do I find the ip address for my AirPort Extreme?

    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click on the AirPort Extreme icon
    If the AirPort Extreme is performing as the main router on the network, Info will be displayed about the Internet, or public IP address, and also the private LAN or local IP address of the AirPort Exreme.
    If another device is performing as the main router on your network, only the local IP address of the AirPort Extreme will be displayed.

  • Airport Extreme invalid IP address, no DNS server

    Hardware: Motorola SURFboard SB6141, Airport Extreme A1408
    I recently set up a new internet service with Cox, plugged in the SB6141 and A1408 and everything set up perfectly, solid green light and wireless was flawless. However, electricity to my house had to be reset, and when the power came back on the green light on the Airport Extreme started to flashing amber. I did several hard/factory resets of the Airport Extreme as well as unplugging the modem and leaving everything unplugged for several minutes and then plugging everything back in. No matter what combination of things I try to do, the Airport Utility always tells me the same 2 errors: invalid IP address and no DNS server. Why was the Airport Extreme able to automatically set up the first time, but not now? Any ideas of what I can do? Thanks!

    I have also looked through other threads about this same problem, but none of the solutions (e.g. posts by Tesserax, followed to the letter) so far have worked.
    Here are other things I have tried:
    1. Called Cox to have them reset my modem, internet works through Ethernet directly from the modem
    2. Downgraded AEBS firmware to 7.6.1 (oddly enough, now I cannot for the life of me update the firmware back to 7.6.4, always says cannot connect to update server)
    I ran through the various solutions from this thread: "No DNS servers" and "Internet connection" problems with Comcast?
    Still getting that pesky blinking amber light.

  • Comcast & Airport Extreme Correct IP Address?

    Apple Support had to help me setup my new Airport Extreme Router, as it turned out, due to a Comcast Internet problem in my area. Everything appears to be working correctly now, however, what is the correct default Apple Extreme IP Address?  I found an article that stated 10.0.1.1 is not a valid IP address.
    Please note, I am able to connect to the internet with my 2 laptops (wired or wireless), plus my iPhone, plus my Printer (USB connected to Airport Extreme), plus my DVD player and ROKU.
    Thanks

    Thanks for that quick response.  Trust me, after the poor Apple Tech person had to work with me for an hour to get this working correctly, I am NOT touching it!
    We couldn't get the Airport Extreme to recognize a valid router address - had to unplug the Comcast Ubee modem, take out the battery & we finally also disconnected the coax cable on the 3rd try.  3rd try was a charm & this has been fantastic for 3 days now. Then I found out there had been an issue with Comast Internet in my area, which may have caused us the setup heartache.
    So thanks for answering and I am happy with the setup as is.

  • Airport Extreme missing, blinking yellow

    I'm in the middle of setting up my AEBS, when suddenly it dissapeared from the Airport Utility scan.  Now I only have a blinking yellow light, and no base station to choose (or configure).  I've powered down, and resent via the reset button on the back of the AEBS.  Still no base station in Utility.  How do I "see"my base station again????

    When the AirPort Extreme (AEBS) goes missing, try an Ethernet cable connection from your Mac to one of the LAN <-> ports on the AEBS to establish a direct connection, rather than wireless....which can be problematic
    You may need to perform a Factory Default Reset again to get things back to a starting point again.
    To do that....
    Pull the power plug from the back of the AEBS
    Wait a moment or two
    Hold in the reset button and continue to hold it in an additional 8-10 seconds while you plug the power back in to the AEBS
    Release the reset button and allow 25--30 seconds for the AEBS to restart to a slow, blinking amber light
    You can keep the Ethernet cable connected to the AEBS until you have it updated with new settings, then you can remove it if you wish
    Post back if you need a few more setup tips

  • ARD vs Airport Extreme - flaky 3283 addressing?

    I have a MacPro and MacBook Pro behind an Apple Airport Extreme b/g/n (non-dual mode wireless). I use ARD 3.3.2 to access several servers. When I open ARD behind the Airport only a few machines show up as 'fully accessible' with a valid status entry and ability to do things like file copying. The rest of the machines show up as either 'Offline' or 'Screen Sharing Only', but in all cases those machines are fully accessible if one removes the Airport Extreme and connects directly to the internet.
    Has anyone found a way around this bug?
    Thanks!

    Sorry, but there is no alternative to forwarding the ports; that's the way TCP/IP works with NAT (which the AE is using to give your laptop it's IP address). Forwarding is no less secure, though, than if the system has a native IP address.
    But if you've turned off ARD in the Sharing preference on your laptop (I presume it's your admin laptop you're referring to), the ARD administration app will still work, but it will be impossible for anyone to access your laptop through ARD (and all but impossible though anything else), so you really don't need to worry. If you're truly concerned, you could run a traffic monitoring utility such as Little Snitch which can alert you to any attempts to access your system.

  • HH3 Airport Extreme DNS / router address issues

    I have a HH3 hard wired (ethernet) from HH port 1 to the small circle port on the Airport Extreme.  The AE extends the network around the house via Airport express and we have done this by creating a new network so we can connect either to the HH or to the AEBS network.  The AEBS is set to bridge mode but wrong DNS and router addresses are given out by both HH and AEBS when the AE is turned on (192.1.68.1.2 instead of 192.168.1.254).  We can bypass the issue by setting these manually but would prefer not to have to.  If I turn the AE off, the HH issues the correct DNS and router addresses.  I am asking the same question on the Apple forums but not everyone there is familiar with the HH.  

    Bizarrely, having tried every configuration on the AE, reminded of something vofsanity said to me in a previous thread, I unplugged a powerline extender and the problem seems to have fixed itself!

  • Airport Extreme changing MAC address

    I have a very frustrating situation. One of the UFO airport extremes on our network is spontaneously changing it's MAC address. In the server logs, there is a message that IP address "xxx.xxx.xxx.xxx moved from MACaddress1 to MACaddress2". The IP address is for the airport base station and one of the MACaddresses is the WAN port of the of the base station. There are times when the MAC address changes back and forth several times in a span of a few minutes. Needless to say, this is causing severe problems with our wireless network.
    I have flushed the routing table on our servers. I have done a hard reset and reconfigured the base station.
    Let me know if more information is needed.
    Any assistance would be greatly appreciated.

    cdated, Welcome to the discussion area!
    Since there is no way to change the MAC addresses used by theAirPort Extreme base station (AEBS), I would suspect that another device is acquiring/using the AEBS's IP address.
    Have you tracked down the device/port using this 2nd MAC address?

  • AirPort Extreme LAN IP Address, where?

    I open the AirPort utility and over the AirPort Extreme you get the list of computer connected wireless, but what about the wire (LAN Ports) I could not see any of the 3 computers connected. How or where its possible to fine the computers IP address connected trough the LAN Ports? I mean the DHCP List for the wire and wireless divice.
    AirPort Extreme 7.6.1
    AirPort Utility 6.0

    i just set mine up right now...
    open airport utility...manual...internet...DHCP... then change to the IP you like. i set mine to be DHCP range of 192.168.0.100 to .150 and AE set itself to 192.168.0.1

  • Airport Extreme Internal IP Address

    I just purchased an Airport Extreme. I am trying to manually set the internal IP address, but do not see an option to do this. The current internal IP is 192.168.10.1. Can this be set manually (i.e. to something like 192.168.10.254), or am I stuck with x.x.x.1? Thanks!
    MacBook Pro   Mac OS X (10.4.9)  

    You are stuck with .1 on whatever private network you choose.

  • AirPort Extreme LAN IP address

    Hi
    Is it possible to set the LAN IP address of an AE (Simultaneous Dual-Band II)?
    As the AE is my gateway I would prefer to have it's LAN IP address set to 192.168.x.254 rather than 192.168.x.1 which seems to be the default.
    Cheers
    Smudger

    Hi William
    I don't see any way to do that in Airport Utility either.
    The reason I want to do it is that I'm a network admin from way back (as the saying goes "when Pontius was a pilot") and .254 has always been the default for gateways. When I changed to the AE I had to edit a bunch of config files to cater for the gateway selecting .1 instead!
    If it can't be done, it can't be done. But I think it's a shortcoming of the unit.
    Thanks anyway.
    Smudger

  • How do I open ports on my airport extreme and assign a fixed IP Address for a device connected to my network?

    I recently had a security system installed in my house.  One of the features is an EPAD which enables me to have a virtual keypad on my iphone, and computer to operate the alarm system.  The technician was not familiar with Mac's and Airports.  How do I open port 80 to 80 in my airport and assign a fixed IP address for the EPAD?  Apparently this is what is needed to make this work.

    There are three ranges of "strictly local" IP addresses reserved for local Network use:
    192.168.xxx.yyy
    172.16.xxx.yyy
    10.xxx.yyy.zzz
    What your Router does for you is to act as your agent on the Internet.Your requests are packaged up and forwarded on your behalf, and only when a response is expected is the response returned to your local IP address.
    Directing Network Traffic to a Specific Computer on Your
    Network (Port Mapping)
    AirPort Extreme uses Network Address Translation (NAT) to share a single IP address with the computers that join the AirPort Extreme network. To provide Internet access to several computers with one IP address, NAT assigns private IP addresses to each computer on the AirPort Extreme network, and then matches these addresses with port numbers. The wireless device creates a port-to-private IP address table entry when a computer on your AirPort (private) network sends a request for information to the Internet.
    If you’re using a web, AppleShare, or FTP server on your AirPort Extreme network, other computers initiate communication with your server. Because the Apple wireless device has no table entries for these requests, it has no way of directing the information to the appropriate computer on your AirPort network.
    To ensure that requests are properly routed to your web, AppleShare, or FTP server, you need to establish a permanent IP address for your server and provide inbound port mapping information to your Apple wireless device.
    To set up inbound port mapping:
    1) Open AirPort Utility, select your wireless device, and then choose Base Station > Manual Setup, or double-click the device icon to open its configuration in a separate window. Enter the password if necessary.
    2) Click the Advanced button, and then click Port Mapping.
    3) Click the Add button and choose a service, such as Personal File Sharing, from the Service pop-up menu.

  • How can I change my IP address in airport extreme?

    I have an airport extreme and I would like to change the IP address.  There is a renew DHCP tab next to IPv4 Address in Airport Utility, but if I click it doesn't change anything.  I'm very green on IP addresses, how can I change the IP address?

    I am currently connecting using DHCP.  The reason I want to change my IP address is for security.
    I see, thanks for the explanation.
    Every time you connect to a website, any website, your IP address is sent along with the content you request. There is no avoiding that. It's the method by which the content is delivered to you, analogous to a return address on an envelope you send in the mail. It's not required for websites to maintain a log your IP address or the content you requested. Most of the time it's discarded.
    That IP address sent with your web page request is the address of your ISP's router - not your AirPort Extreme. Its address can be used to identify only a broad geographical area, and only your ISP will know the location of the specific equipment it's using. To truly obscure your location from even that broad category requires connecting through a web proxy server, of which there are many to choose from. The only IP address that could be "tracked" using one of them could be anywhere around the world, and would change so often as to be useless to anyone wanting to locate you.
    In any event specifying a fixed IP address for your Extreme will not accomplish anything in the way of security or privacy, and would be no different than using DHCP.
    If you are concerned about privacy in general that is a very wide-ranging subject. I'll start by suggesting you avoid Google and all its products and services, for obvious reasons.

  • How do I obtain a valid ip address for my airport extreme?

    When setting up my airport extreme, the ip address it always attempts to ue begins with 169.  i know this is not a valid ip address; I shoud have 1 that begins with 174.  How do I resolve this?

    Thanks for the info. I am not familiar with this model, so will need to read up a bit.
    Just to confirm......does this appear to be your "modem"?
    DDW3611 | Ubee Interactive
    If yes, you might be interested to learn that it is a modem/router....also known as a gateway device.....quite different from a simple modem.....so the requirement to connect will be different from a simple modem.

Maybe you are looking for