AirPort Extreme not visible in the airport utility installed on my Imac

My AirPort Extreme is suddenly not visible in the airport utility installed on my Imac. After numerous rescans I am bordering to give up as the connection seems to be working fine when I connect it to the Imac through the ethernet cable. Any advices further than restarting the devices?

For the app Airport Utility you have to be connected to the AE wifi.
If you are not talking about the AU App, but the Airport Antenna you can do following:
disconnect AE form power, wait 10-15 seconds, turn off the Airport Antenna in your mac. Then connect the AE to power, wait till it is fully started, then turn the Airport Antenna to on again.

Similar Messages

Airport Extreme not reconnecting to the Internet

Hello,
I have a problem with my brand-new Airport Extreme 802.11n Base-Station.
In my network there are 3 Windows-PC's with a wired connection, 1 MacBook Pro with 802.11n (also brand-new), 3 Windows-Laptops with 802.11g, an AppleTV with 802.11n (again, brand-new) and last but not least my iPhone 3G.
I set up the Airport Extreme basestation to connect to the Internet via my DSL-modem with PPPoE (the modem is a 25mbit-modem from Devolo and works flawlessly).
This works fine at first and all devices can access the Internet, the HDD connected to the basestation and so on... I was a happy user.
My Provider requires me to reconnect to the internet at least once every 24 hours.
Now when the connection reaches its 24 hour limit, it is disconnected by the provider.
This worked fine with my previous basestation, every morning at 3am it reconnected for 5 seconds and I had no problems.
But my Airport Extreme wont re-establish the connection automatically.
It doesnt reconnect right after the connection is cancelled and it doesnt reconnect when a computer wants to access the internet.
The only way to reconnect to the internet is via the Airport Utility and clicking on the "update"-button to cause a reboot of the basestation.
After it has rebooted the connection will work for 24 hours and then the basestation needs another reboot.
How can I get my basestation to reconnect to the internet without rebooting it every time.
I would prefer a reconnect right after the connection is dropped but I'd settle with an automatic reconnect once a device requests a connection.
However, since most users are not very experienced, all of this would need to be automatic once i set it all up.
Thanks for your help in advance...
Jochen

I have asked my ISP but they said it was an unknown issue to them and that they are not responsible if my things dont work the way I want them to...
And they are absolutely right in saying its my device that acts strange since the previous router (with integrated modem) didnt have this issue.
I will try to use QuickKey and contact the Apple-Support directly.
A friend of mine works in an Apple-Store and will need to look at this later, but he is on holidays...

Airport extreme not showing up in airport Untility

My airport extreme is not showing up on my mac in airport utilities, was blinking amber I unplugged it back to green but still not showing up in airport utility

Suggest that you restart the entire network by powering everything off...order is not important...and starting the modem first, then AirPort Extreme, then each device one at a time.
Temporarily, connect a spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule.
Check to see if AirPort Utility can see the AirPort Extreme
If this works, when you have completed checks or adjustments on the AirPort Extreme, you can disconnect the Ethernet cable.

HAAALP!!! AIRPORT EXTREME NOT SHOWING UP ON AIRPORT UTILITY

I have two airport extremes one to make network and one to expand it. the one i have to make the network is working fine and is a FINE peice of machinery. but the second one i have to extend my network will not show up on airport utility. and no i am not a stupid and didnt plug in the wires right everything is in perfectly and i use to be able to configure it then one day it just stops so i reset and configure it with airport utility. but after it restarts the airport and updates it. it will not show up on airport utility. PLZ help i have tried everything reset it a millions time and some times it will show up then i will change the settings again!! and it will not show up again!!!!! plzz plzz HELP

they are already in the same room and i am doing it on the same computer and it feels like it has gone into a land it can not come back from. also i just realized that it stays amber constantly like its in its startup process. and after a while the light just goes OFF. so idk and i have hard reset it and isnt it supposed to flash lights (cause it doesnt) when i hard reset it. well idk its weird its like it take forever to startup or something cause all of the sudden it will show up on airport utility but after i configure it again it restarts and can not be found again. ;{

Radius, Server App, and Airport Extreme (not visible)

In the help system online it states "In the Server app sidebar, select your AirPort device. The AirPort device is listed in the Hardware section of the sidebar. If you want users to log in to your wireless network with their user account credentials, select “Allow user name and password login over Wi-Fi". Well, that is nice, but nothing I can do allows it to show up in the hardware section of the sidebar! Now I have configured it through the "Server Admin" tool, but it is kind of frustrating that all of the documentation points to the Server App and right clicking on the Airport device... Thoughts? Is there something I missed on the Airport configuration to allow it to be seen by the Server App?

Your Airport Device has to have the right configuration to show up in the server.app sidebar. Otherwhise server.app can´t manage the airport device.
Here is an support page where you can find out how the configuration has to be, if you want to manage your airport device with server.app: http://docs.info.apple.com/article.html?path=Server/10.7/en/t_ManageAirPort.html

Airport Disk not visible on finder after Leopard install

On Finder, my Airport extreme appears but I can't see anything on my HD attached.
But if I open a terminal, I can browse my Airport disk.
Anybody have a solution?
Thanks

Go to Finder = Preferences
"General" icon and check [x] Connected Servers
I had to reboot to make this work. Your mileage may vary per when the disk icon is visible.

My Airport Base Station does not appear in the Airport Admin Utility

I cannot see my airport extreme base station in the Airport Admin Utility nor in Airport Setup Assistant via Airport. It worked yesterday but when I was trying to set up a network something must have changed but I don't know what it is. (The setup didn't work so I am only using one base station right now.) The only way I can configure/reconfigure the base station is by physically connecting via an ethernet cable. Then no problem. I have two computers and neither can access the base station with Airport Admin Utility via Airport. I have installed the latest Airport Update but nothing has changed. What happened?

You should be able to use the second Airport Extreme
Base Station as a wireless print server. What I
suggest you do is:
1. run the Airport Admin Utility and clean up
settings on your existing Base Station:
- under the Airport tab, make sure you have not
selected to "create a closed network"
- under the Access Control tab, clear out all
settings
- under the WDS tab, clear out all settings
- under the Network tab, make sure the box is checked
to "Distribute IP addresses" and "Share a single IP
address using DHCP and NAT".
- update settings to the Base Station if you changed
anything.
2. do a hard reset of your second base station per:
http://docs.info.apple.com/article.html?artnum=107451
3. for now, put both base stations and the Mac in the
same room. Run the Airport Setup Assistant, and use
its guidance to configure the second base station as
a new base station that "extends" the wireless
network of your main base station.
That should do it.
Thanks very much. The printer works great from both computers via my second airport base station. And I can see both my base stations in the Airport Admin Utility.

Recently bought airport Extreme and have connected the device to the modem. WIFI works. However when I connect the LAN port to a switch I do not see the LAN printer and my NAS. Which setting do I miss?

I have installed my Airport Extreme and have conencted it directly to a modem. WIFI works fine. However I do not see my LAN network (printer. NAS,..).
Analysis:
Scen#1: When I connect the LAN port of the Airport Extreme to a switch (as input) and connect the other LAN devices also to the switch, those LAN devices do not have access to the internet. Also connecting the iPAD with WIFI to the Airport Extreme I cannot find my LAN printer and other devices.
Scen#2: When I connect the LAN port of the Airport Extreme to a router X (as input) and connect the router X to the same switch, and the LAN devices to the switch, those LAN devices do have access to the internet. Also connecting the iPAD with WIFI to the router X I can find my LAN printer and other devices in the LAN network.
Question what has impacted the behaviour of the Airport Extreme, not to detect the devices in the LAN network. Why is the use of a switch directly behind the Airport Extreme not working (no internet access for the other devices and Airport Extreme is not the basis station for the LAN network)?

Your scenario #1 is a correct configuration and should work. It seems as though your Extreme is not acting as a router as I believe you intend.
Most likely, you need to reset your modem. Power it down and let it rest for a few moments. Some need longer than others. Then, I recommend you "hard reset" your Extreme (see below) and configure it again, after the modem has been reset. From then on do not change what is connected to your modem without powering it down first.
Once configured, confirm your Extreme's wireless network works as expected and that your iPad and every other wireless device can load web pages. Then, connect the printer directly to one of the Extreme's LAN ports and confirm that it works as well. After that it should work equally well with a switch between it and the Extreme, as should every other wired device connected to the switch. This assumes your switch is an unmanaged device requiring no specific configuration.
Scenario #2: Having a router connected downstream of another is not a normal configuration, so don't pursue that as a solution. It will only distract you from determining the problem. If you want to repurpose Router X as another device do so only after everything else is working to your satisfaction.
To "hard reset" an AirPort Base Station: make sure it's powered up, then press and hold its tiny reset button and keep it depressed for five to ten seconds, long enough for its LED to flash amber rapidly. Release the reset button. Then, the LED will glow amber steadily for about a minute. Then, it will flash amber, slowly, about once every second or two, waiting for you to configure it with AirPort Utility.

Brand new airport extreme not found on utility on iPad

I Just purchased the AirPort Extreme. My first Apple router but all of our devices are apple products with the exception of our pc. Extreme is flashing Amber light and is not found in the airport utility app. I want to enjoy this apple product as much as the others but it's becoming difficul.

OK, thanks for clarifying that for me.
If you have the Setup Guide handy that came with your AirPort Extreme, please head for page 12 and locate the heading to......
Setting Up AirPort Extreme Using an iOS Device.........To Set It Up
The steps here are pretty clear, and we rarely get a question about this but, we'll go through this in case you might have missed something.
1. Tap Settings on the iPad home screen. Settings is the gear looking icon there. Then, tap WiFi. WiFi is on the left side of the screen.
2. Tap the name of the AirPort Extreme. AirPort Extreme is located just under the heading of SET UP NEW AIRPORT BASE STATION there.
In the example below from an iPhone screen, I am setting up a new AirPort Express. So, I would tap on AirPort Express. You will see AirPort Extreme on your iPad screen, so you would tap on AirPort Extreme.
When you do this, that will start up the setup wizard.
3. Follow the onscreen instructions to create a new network or extend an existing network. The setup wizard will analyze the network and suggest the correct setup for you.
Once the AirPort Extreme has been set up, then you can use AirPort Utility to edit or modify any of the settings that you might need to adjust.

I just purchased an airport extreme router to increase the range of my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

I just purchased an airport extreme router to increase the range of my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

sylviafromhanover wrote:
So I assume that the original modem stays installed with the coaxial cable and the Exrtreme is in addition to that.
Yes, that is correct.
Did you have the instructions that came with your Airport Extreme? Are you sure you have it setup properly? Here is the setup guide:
http://manuals.info.apple.com/en/airportextreme_802.11n_userguide.pdf
Ensure you have everything setup properly. Once you do this and if you are still having trouble, follow Star's instructions.

I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

I'm not sure how to post a message. I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I have an older Airport Express, would it help to install it? would it work best if it was installed in the same room? should it be installed half way in between? Get another Extreme? The Mac Book Pro on the middle floor can see 11 networks in the neighbourhood if that might be causing a problem or would if I installed the Express. Thank for your consideration.

Thanks for your time ... I appologize for the font and colour, I compossed the question in pages and failed to notice the font colour as grey ... there are a variety of computers of various ages so I think it is using a setting that allows both 5G and 2.4 ... the connection to the Airport is thru a cable modem and cable does run throuhout the house ... maybe those hard wires would be a place to look at ... do you think that putting the 'Express' on the second floor might help ... thanks again ...

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more information."

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Any thoughts?

This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

Airport extreme not showing in airport utility

I am running osx10.7 server and am attempting to port remap my airport extreme. When i open airport utility, it says that there are no airports in range, when i'm actually connected to an airport via wifi. I cannot figure out what the issue is. If someone can help me fix this issue and instruct me how to remap my rounter so i can use it to host websites and the like, it would be greatly appreciated.
Thanks a lot for your help in advance.
Zach Russell

grimstad wrote:
My Airport Extreme is working just fine, but I want to add Airport Express. The first step in my manual says to open Airport Utility, but I get the message "Airport Utility was unable to find and AirPort wireless devices.
This may happen if your system accidentally switch the radio band.
Try this first:
Disable WiFi in the Menu Bar
Enable again
Check if the Airport Extreme shows up in Airport Utility
If so, choose the Airport Extreme
Click Manual Setup
On there:
If possible disable "Guest Network" (it cause trouble by switching constantly radio band for user convenience)
Give the 5GHz wireless a dedicated name
If you have no 802.11g (iPhone, iPod Touch) in the network:
Set radio mode to: 802.11n only (5GHz) - 802.11.n only (2.4GHz)
If you need 802.11g
Set radio mode to: 802.11n only (5GHz) - 802.11b/g
You will reach these settings by holding option key (alt) while clicking on the Radio Mode pulldown.
Click Apply and wait for the Extreme to come back
After that,
check that your 5GHz capable systems use only the 5GHz name (SSID) when joining wireless.
For that, delete the 2.4GHz name (SSID) from the list of known networks in Systems Settings - WiFi - Advanced
Move the preferd network in the List at first place.
Rejoin wireless
Lupunus
PS ... to configure the Express, best connect a laptop via Ethernet to them. This eases the process a lot.

I cannot add a Wi-Fi guest network. Gone to Utilities Airport Utilities and all get is an image/browser of my Airport Extreme. Looking for the browser which has the title Wireless but cannot find anywhere. I need help?

I cannot add a Wi-Fi guest network. Gone to Utilities>Airport Utilities and all I get is an image/browser of my Airport Extreme. Looking for the browser window which has the title Wireless but cannot find anywhere. What am I doing wrong?

Open AirPort Utility. The first screen looks something like this:
Click on the AirPort Extreme and another screen will appear. Click Edit, then the window with the Wireless tab will appear.
If you do not see these screens, you will need to start over and configure your AirPort again.

Can I use an Airport Extreme Base Station from the USA in Europe ?

A friend of mine gave me an Airport Extreme Base Station from the USA to Germany. When I hook it up to my PB by ethernet cable the Computer can't find the Base Station at all. If I use my Sonnett Aria Extreme PCI card it finds the station but in the pop-up menu asking in which country I want to use the airport station it only offers North and South American countries. How do I go from here and why is my PB not finding the station when I'm using cables ? Has it something to do with different models for different countries ? Any idea ? Thanx

Here you go ...
Changing the Radio Channel on the AEBSn
Either connect to the AEBSn's wireless network, or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN ports of the AEBSn, and then, using the AirPort Utility in Manual Setup, check these settings:
AirPort - Wireless
o Channel: <Use Automatic or select a preferred channel>

AirPort Extreme not visible in the airport utility installed on my Imac

Similar Messages

Maybe you are looking for