Airport Extreme off a Router which provides DNS - Guest Networks

I am sure that I am not alone here.
I have a BTBroadband wireless ADSLModem/Router which provides DNS for the network.
Off tyhe router is a Netgear switch which has connected to it an Airport Extreme. Also off this switch I have many other peripherals - such as Time Capsule, iMac etc.
So the arrangement is simple in logical terms:
BT Modem------->Wireless Router (which allocates DNS)---------->Switch----------->Airport Extreme etc.
IP Settings as follows
192.168.0.1 for Wireless Router - which allocates DNS in range 192.168.0.2 to 0.150.
I have allocated a fixed IP on the Airport Extreme of 192.168.0.151
The devices thart run off this are all having DNS allocated by the router - not the Airport Extreme.
So - how do I set up (or can I set up) the Guest Wireless Network?
Let's assume Router Wireless Network is call MainWireless with a Password MainWord, The Airport Extreme is acting in Bridge Mode and has the exact same 'Create a wireless network' called MainWIreless and Password MainWord (as per best practices in using these to provide the best 'network hopping' capabilities for devices (I actually have 2 other wireless devices from TimeCapsules that operate the wireless in the same way).
All of this works fine.
However when I set up the Guest Network on the Airport Extreme - simply by enabling it - I provide a new Guest Network name of GuestWireless with a password GuetsPassword. In theory it should all work fine, however the devices connecting to the Guest Network cannot get to the internet (effectively I don't think that the 'iPhone for example' is being allocated a correct IP Address - in fact I know that it isn't as its a 169 range and a different subnet).
So - the only way I can think of doing this is to go into the Network Settings on the Airport Extreme, Change Bridge Mode Wireless to DHCP and NAT and then go into Network Options. Here I am a bit lost and need help.
To summarise - Main Router Address 192.168.0.1 allocates range 192.168.0.2 to 150, Airport Extreme Address (static) address 192.168.0.151.
Airport Extreme DHCP and NAT Network Options has:
IPv4 DHCP Range - I have set to 192.168.0.152 to 255
Guest IPv4 DHCP Range 10.0.0 152 to 255
NAT Port Mapping Protocol is switched Off
- This won't even save.
Should be simple I would have thought. Think again...
Please help - mwhat should I / can I do to enable a guest wireless network?

Thanks for all that - I suspected as much (and I did mean DHCP not DNS).
So - if I disable DHCP on the HomeHub3 IP 192.168.0.1, and set the Airport Extreme IP Address at 192.168.0.2, what do I do with DHCP and NAT settings to have a Main and Guest Wireless Network?
I can easily change the order of things if necessary to be :
BT Modem (192.168.0.1 with DHCP disabled)--->Airport Extreme (192.168.0.2 (set to get DNS from 192.168.0.1) )--->Switch---->Various wired and wireless devices.

Similar Messages

3 Airport Extremes, 1 as router 2 as APs, Guest Network

I have 3 Airport Extremes, all 5th Gen, all Wired with CAT6. I have the first one setup as DHCP and NAT, with wireless off(basically acting as just a router)...Then its connected to a gigabit switch whitch then the 2 other Airport Extremes are set in bridge mode to create the same network name and pass. What i am wondering is can i still create a guest network? the option shows up in wireless in AU 6, but i noticed there is no way to set the IP range as for obvious reasons (they arent in dhcp mode)...has anyone tried this or have any advice?

so the first AEBS has to have wifi enabled? in order for the other 2 AEBS to create the guest network?
Yes. If the Guest Network is not enabled on the first AirPort, then other AirPorts will not be able to extend a network that is not there in the first place.
what if i the 2 AEBS wifi stations are in dhcp only and guest network enabled
This will not work.
is the a way to have all 3 AEBS on the same wireless channel to create this?
The correct setup in a roaming network is for each AirPort to be separated by 4-5 channels from others. This will usually happen automatically if you use the default "Automatic" Radio Mode setting, or you can set channels manually. You would not want each AirPort to use the same channel.

Airport Extreme with ATT Router for Open DNS use

I'd like my whole home network to have a filter on it so all computers and hand devices are protected. I get my internet with an ATT router which I can not change the DNS servers. ATT says they can not be changed. But I have an airport extreme directly connected to the ATT router. The extreme supplies wi-fi to the house. I can not change the DNS settings in the extreme. They are grayed out. I'm assuming it has something to do with the connection to the ATT router. Does anyone know how I can put a DNS address in the extreme?
Some of the settings on the extreme are:
Internet Tab: connect using DHCP, DNS Servers "grayed out", Domain Name "grayed out"
Network Tab: Router Mode (off (bridge mode))
thanks!

Does anyone know how I can put a DNS address in the extreme?
Not sure what you mean that you cannot enter the DNS numbers on your AirPort Extreme configuration page.
Open up AirPort Utility and select the Internet tab
Look at the first DNS entry there. There should be a cursor at the beginning of the DNS Server Box. If not, click to set the insertion point at the beginning of the box.
Simply start typing in the DNS server number that you want to use.....208.67.222.222...... and it will overwrite the grayed out values there.
Do the same for the second DNS box....208.67.220.220.
Click Update at the lower right and you are all set.

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router
1. I’m writing from a rural town in Southern Nepal, very close to India. I’m planning to create a new WI-FI network at a small monastery here. Ideally, we will have two parallel wireless networks: the first network produced by an ADSL router/modem and a second network produced by another router in “repeater” mode.
2. Earlier, someone suggested that, when I post a question, I should provide as many details as possible about the situation here. Forgive me if there is “too much information”. I have to make a trip to the US to buy new networking equipment, so I very much want to get this right. Once I return here, I’ll be pretty much stuck with whatever I get in the US.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX). An Apple router would be ideal because my experience with Apple routers is happy: they are easy to set up, reliable, and secure. Moreover, we use Apple computers and iOS devices here (and the new AX has the “ac” thing which will be preferable as we replace old machines with new ones).
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
6. Our current, super-crappy 2wire 2701hg-t (ADSL modem/router) covers the 100-foot distance without a problem when it is working and there is Ethernet flowing to us. Frequently, our connection is very bad, and I may be unfairly judging the 2wire 2701hg-t. But, based on user reviews on the America Amazon.com, the 2wire 2701hg-t is pretty terrible: first it is simply old and second, among other problems, it seems to have a poor quality power supply unit. I do observe that it frequently seems to be recycling from scratch as if it had turned off and restarted. In any case, we are replacing it since it may be about 4 or 5 years old.
7. In previous posts on this forum, “LaPastenague” responded to some of my earlier questions about AX and ADSL. Among other things, he pointed out that (1) line-attenuation may be contributing to our poor connection and (2) we must choose a modem/router that is suitable for “long lines.” I’ve looked at our current modem/router statistics page; however, there are no statistics for line-attenuation or noise. (As you will see below, my strategy is to get the “better” modem/router that is suitable for long lines.)
8. Concerning our ADSL service, these are the facts I’ve gleaned from looking at the current router’s configuration pages:
Connection Type: PPPoE
Currently, the router is configured to use WPA-PSK security.
Connection Speed: Incoming: 1024 kbps & Outgoing: 509 kbps
(The following information may be unimportant at this time.)
Broadband Link Diagnostics:
DSL Synchronization: UP
G.DMT Signal: UP
PVC Connection: UP
PPPoE Service: UP
PPP Authentication: UP
IP Connection: UP
DNS Communication: UP
9. The ISP (Nepal Telecom) doesn’t supply a modem/router; however, they do have a list of (at times ancient) hardware and hardware vendors:
http://www.ntc.net.np/internet/adsl/adsl_vendersConf.php
10. Concerning what equipment is available here, what I have observed is that generally the ADSL modem/routers for sale locally, and in the far-away capital Kathmandu, and in nearby India are often also available in the United States, but they are the cheaper, older models. I will have to buy the new equipment in the US this year. At a different institution nearby, they are using the TP-Link modem/router td-w89016 which they purchased locally, I believe.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
13. In fact, does connecting them with a cable help alleviate some of the problems that can occur between the Apple device and the ADSL modem/router?
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
I think there are a lot of good reasons to use an AX router. Of course, if it is just going to be very cumbersome then, we would be loosing one of the best parts of using Apple products. So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple. Apple can rest assured that I will buy other things from them!
In that case, I’d likely buy a second TP-Link device to create a second network:
TL-Wa801NP [AP Mode Multi-SSID Mode AP Client Mode Repeater Mode (WDS / Universal) AP+ Bridge mode (point-to-point / point to Multi-point)].
Thank you in advance. Long live Apple!
Message was edited by: Jess1911

I am not sure if there are different interfaces but my 2wire does an excellent job with line info.
I get into this from browser.. using main IP.. in my case 10.0.0.138/MDC
In your case it should be whatever the IP of the 2wire is, followed by /mdc
Give it a try.
As you can see it shows vendor and loads of info about the line.
I rate it the best domestic modem for line info.
A good modem actually albeit a lousy router.
MDC is the diagnostics and Management Console.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
You are not repeating.. you are simply setting up two routers which are interconnected, so one is dependent on the other.. ie one is your adsl modem router and that will take the main router function. Your second router is really not working as a router, but as wireless access point (and switch if you plug things in).
That is perfectly fine. You are not roaming in this case since both routers are running different wireless names and networks.. but they are actually using same IP range.. all devices are on the one IP network with two different wireless access points.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX).
Apple router is fine for this. Easy to configure out of the box.
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
The problem arises when you try and interconnect using wireless extend or repeater.. you are not using wireless to extend, you are using ethernet. Wired has no issues.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
It is a good choice.. It should be fine considering how poor your line is.. this modem is proving to have a couple of bugs.. it does not handle torrents well but I would suggest your system is not being used for that purpose. It has some port forwarding issues. Again you are probably not going to overload it.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
Absolutely best.. only decent method.
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
Bridge. Although if it gives issues there is another method, although rather complex to setup.. not something to worry about now.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
Only the adsl modem has the ISP authentication.. it is the box that does the link. The TC just piggy backs.
The passwords on the TC are for its Admin, wireless and disk access.
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
For ADSL you must have the PPPoE authentication username and password.
So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple.
hmmm.. I am biased because I see the issues not all the good stories..
The latest airport and Time Capsule seem to have a few pretty severe bugs.. if they happen to hit you, they are extremely hard to fix if you are in the middle of Nepal. And Apple service centre is a long long way away.
I cannot answer your question from the point of view of a person on the ground in remote area. If the economics of the purchase works for you, great. Go for it.
In terms of wireless coverage.. the Asus AC models or Netgear R7000 kill the Apple. Sorry but it is just fact.
See reviews here.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/113-5-ghz-dn-c
That is average.. if you look at the apple router in the worst location by changing the filters, it comes out worse again.
I cannot post the URL to our local forum here.. (apple doesn't allow it). But in testing with apple clients the asus still beat Apple router soundly.
Pure wireless range is not the only consideration.. but in a mixed environment and since the wireless on the 8980N is not too bad.. then buy Apple router for apple client devices makes good sense.
Maybe the older Gen5.. or two of them.. would do a better job.. with a bit more tested and known hardware.
One thing you do need to check.
Routers from every other brand allow you to select country. Any country from anywhere in the world. Apple routers do not.
If you buy an airport in North America it is coded to North America and offers just a few countries.. USA, Canada I suppose.. what else is North America??
You cannot change it to Nepal.
To get the one for Nepal you must buy the model that covers, South Asia I guess.. I am not sure which it is.
See what the license information is for wifi in Nepal as it might be very different to US and therefore illegal for you to run it in Nepal.
If only the whole world would just bow to America.. we could all follow the FCC regs..
http://en.wikipedia.org/wiki/List_of_WLAN_channels
This only applies to the Apple.. the TP-Link etc allows you to choose Nepal or correct country regulations for wifi.
Buying modems has one tricky bit.. that the actual adsl ATM channel is different in different parts of the world. No modem is usually impossible to setup but some can be difficult if it is pre-configured for US.. this is easy to overcome generally as you can download a firmware for another locality, so you can have local settings.

Installing airport extreme after a router

when connecting an airport extreme to a router (AE after the router), should the wire from the router go into the WAN or LAN port of the AE?

It won't matter which port you use if you configure the AirPort Extreme in Bridge Mode, which is the correct setting when you have another router ahead of the AirPort Extreme.
All the ports become LAN ports in Bridge Mode.
AirPort Utility > Manual Setup
Internet icon > Interner Connection tab > Connection Sharing = Off (Bridge Mode)
Be sure to restart the entire network after you change the Extreme to Bridge Mode.

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except join not extend and I can not get a network on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Rout/

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except "join a wireless network (which it does) not "extend a wireless network" (Led turns yellow and I can not get a network working on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Router.
Airport gets it address DHCP.

Funny how I can ping the Extreme but the Hard Ethernet ports dont seem to work correctly.
When the AirPort Extreme is configured to "Join" a wireless network, the Ethernet ports are not enabled.
Oddly, the AirPort Express has a special feature that will allow it to to "Join" virtually any wireless network.....and the Ethernet port can be enabled. So, an Express would work for your purpose to provide an Ethernet connection to the media player. This assumes that the Express is located where it can receive a strong wireless signal from your main router.
Note that the Express will not provide any additional wireless coverage when it "Joins".

Can I increase the range of an AirPort Extreme by a router other than AirPort Express?

Im using an AirPort Extreme as my primary wireless router extended by an AirPort Express at home. We are primarily using macs at home and I'm overall satisfied with the quality of the product. However a lot of online reviews (including pcmag and cNet don't list the extreme or the express) amongst the list of top 10 wireless routers. The ones listed are much cheaper and has received very positive user reviews as well. However I need to setup a new network at my new office and I have some questions regarding setting up a wifi network in regard to AirPort Extreme:
1) Can I extend the wireless network setup via AirPort Extreme Base Station by another wireless router other than Airport Express?
2) I've heard of many cheaper alternatives (Cisco and NetGear being chief) to AirPort Extreme. I've also heard that the network set up by the AE is not as compatible with a windows based environment (which could be an issue as I'm going for an IBM server). In that case which would be the best wireless router for me?
3) Any other specific reason for which I should prefer AE over any other wireless modem?
Any help would be appreciated. Thanks.

1) Can I extend the wireless network setup via AirPort Extreme Base Station by another wireless router other than Airport Express?
Apple appears to have designed their "extend a wireless network" feature using proprietary software, so it would be extremely unlikely that a router from another manufacturer would work with the AirPort Extreme....if you are trying to extend wirelessly.
In that case which would be the best wireless router for me?
That depends on your requirements, and whether you are going strictly for specifications rather than features, or even ease of installation and use. In any case, I can't answer that question.
If you subscribe to industry publications with test reports on products, there always seems to be a new "best" product, so expect that whatever you buy will be superceded by another "best" product within a month.
As far as use with a PC, I've had no issues using several PCs with Apple routers.
3) Any other specific reason for which I should prefer AE over any other wireless modem?
Apple routers are for mom and pop at home. While the product would provide basic functionality in an office, the product was not designed, nor does it have the type of features that most businesses would require.
For example, if I were using a business router, I would expect it use a high grade firewall for security purposes, and for the router to provide reports that track Internet use for each computer, along with a record of what Internet sites were being visited by each employee. Apple routers won't do that.

HT4145 Airport Extreme no valid IP address, no DNS addresses

I have Uverse. I've disabled the wireless feature of the gateway and wired into my airport. I've created a network, and I have all my deviced connected to it. Everything was working fine. Then one day it started losing connectivity everyday. The light was green, but no internet access for the network. A quick restart would fix the problem. Now the light stays amber, and I get two problems: no valid IP, no DNS addresses. Please help.

Re: Airport Extreme IP Address Issue
After hours of trying everything else, this worked!!!
From: Comcast Networking/Router/Wifi Gateway:
Re: Airport Extreme IP Address Issue
11-20-2012 07:11 PM
MyComputerGuyJo:
I just wanted to add what Apple Support walked me through. Worked perfectly. Similar to some of the posts here. This assumes you have finished the setup of the Airport using DHCP to obtain the IP automatically from Comcast and it says the IP is invalid.
Power off\on Sequence
1, Power off Comcast Modem. Remove Battery back up, if it has one. Disconnect the coax cable.
2. Power off Airport Extreme
3. Let both sit for 3 minutes.
4. Reconnect coax cable to Comcast modem and replace battery and power up.
5. Wait a minute or two to make sure the Comcast modem is completely up and then Power on the Airport Extreme.
(When AP asks for DNS, Type in both addresses below)
Re: Airport Extreme IP Address Issue
11-01-2012 03:07 PM
Freyfisher: I had the same problem whenn I switched to the Airport Extreme yesterday. Here is what I did:
1: uplugged modem for 30 sec. and detached all ethernet cables. Plugged back in and reattached airport extreme cable after all lights were solid on the modem. Then, I went into Airport Utility and selected, "Base Station"> "restore default settings". Then" Base Station"> Restart. Then go through setup assistant again. If no luck, try setting IPv4 to 10.0.1.2, subnet to 255.255.255.0, router to 10.0.1.1. IPv6 set to OFF if having trouble. DNS adresses: 75.75.75.75, 75.75.76.76, search domain hsd1.ST.comcast.net where "ST" is your two-letter State abbrev. Hope this helps someone....

I have Verizon FiOS service for phone, internet and TV but I only have one TV hooked up for it for just basic cable service with no DVR and no need for widgets. Can I use an Airport Extreme as my router and not use the FiOs router?

I want to use an Airport Extreme as my router. I currently have a Verizon FiOS router. I have Verizon for phone, internet and TV. However, TV-wise, I just have a basic service for one TV with just a regular box. No HD, no DVR. Don't need access to a menu, widgets, on-demand. Can I eliminate the FiOS Router and just use the Airport Extreme and still have phone and internet?

I know that it will increase my wireless coverage in my house but will it increase the speeds?
Not sure what you are asking here. The AirPort Extreme is only going to be as fast as the Internet connection that it receives.....which is 75/75. It cannot take a 75/75 connection and make it go any faster.
If you locate the AirPort Extreme in an area where you need more wireless signal coverage, the AirPort Extreme would deliver 75/75 in that area. But, keep in mind that the AirPort Extreme must connect to the FIOS router using a permanent, wired Ethernet cable connection.
If you are asking if the AirPort Extreme can wirelessly connect to the FIOS modem router, and extend the FIOS wireless network, the AirPort Extreme would not be compatible with a FIOS product for that purpose.

Connect Airport Extreme to existing router without ethernet cable

I am looking to connect my Airport Extreme to an existing router without the use of the ethernet cable. The existing router is on the ground floor whilst I would like to install the Airport Extreme in the first floor to improve WiFi range on the 1st floor. I am able to connect Airport Extreme to the router with the ethernet cable (in which case both the devices have to be close to one another on the ground floor) but unable to get Airport Extreme set up without the ethernet cable. Is it possible to connect Airport Extreme to the existing router on a non-wired basis (i.e. without the ethernet cable) and if yes, how would be I able to do it. Any help would be appreciated.

The AirPort Extreme can connect wirelessly.....IF.....your existing router is also another Apple router.
Is that the case here? If yes, what model number is your existing Apple router?
If no, you will need to continue to connect the AirPort Extreme using a wired Ethernet connection.

How can I set up an Airport Extreme as a router, in conjunction with my AT&T modem/router?

I am trying to set up an Airport Extreme as my router, and I am currently using an AT&T modem/router combo. I am wondering what would be the easiest way to do this. Any help would be appreciated. Thanks!

Connect an Ethernet cable from one of the LAN <-> ports on the ATT modem/router to the WAN "O" port on the AirPort Extreme. This cable must remain in place permanently.
Open Macintosh HD > Applications > Utilities > AirPort Utility on your Mac
Click on Other WiFi Devices
Click on AirPort Extreme xxxxx
The utility will take a moment to analyze the connection, then a screen similar to this will appear with your AirPort Extreme instead of an AirPort Express
Type in a short simple name that you want to use for the wireless network
Type in a device name for the AirPort Extreme
Enter a password that will be used for both the AirPort Extreme and wireless network
Verify the password
Click Next
The utility will setup everything for you. When the message of Setup Complete appears, click Done and close AirPort Utility.
The AirPort Extreme wireless network is now available.

Does Airport Extreme support Static Routes?

I have client using an Airport Extreme as their Router. They currently connect to another device outside their network using AppleTalk.
It is planned to put this device onto TCP/IP but on a different subnet (e.g. their subnet is 192.168.5.X and the device will be on say 192.168.25.X). Does Airport Extreme support (like other Routers) the ability to set up a static link to a device on a different subnet (can’t find any information in a doco or the utility) or do they need to replace this with a “real“ router?

Sure, I could do something like route add -net 10.100.10 192.168.0.100 on every client machine on the subnet, but there is no such way to configure a web cam and similiar devices
Any idea, Apple?

I am experiencing network failures with my Airport Extremes: the main router is a 2nd Gen, the extension a 5th Gen. The 5th Gen keeps on losing connection with the main router. Any ideas why?

I am experiencing network failures with my Airport Extremes: the main router is a 2nd Gen, the extension a 5th Gen.
The 5th Gen keeps on losing connection with the main router and thus with the internet.
Any ideas why?

Is the second Extreme configured to "extend" the network created by the first? If so its position must be such that it has a strong wireless connection to the first Extreme. If it is at the limits of the first one's wireless range its connection will be tenuous. Place them closer together and determine if that makes a difference.

Airport Extreme Card (will not automatically connect to home network)

Running OSX (10.4.7) on a G5 2.0 DualCore. I just had an Airport Extreme Card installed by Apple a week ago. Everything was working fine with WiFi ( I use a Lynksys Router. But oddly now when I cold boot up, the Airport Extreme will not automatically connect to my home network. The little Airport icon on the upper right is always greyed out ( even though clicking on the icon... says that Airport is "On" ). So I now have to manually select my home network everytime I boot up. The first week or so though, I didn't have to do this...it just automtically connected to my home network. I made no changes to the router settings, nor the Network prefs.

I have been able to get my home network running with simultaneous access to the internet with the MacMini and the PB G4 via a WL router (Netgear WGR614v4 with four ethernet ports).
This was the process:
1a) Turned off airport on both computers.
1b) Turned off both compters and
1c) disconnected the router from the cable modem.
a) Disconnected ethernet cable from WL router to Macmini.
2b) Powered down the router for 10 seconds.
3a) Keeping both computers unpowered,repowered router and pressed the reset button (behind an unmarked tiny hole in the back of the router) then re-connected it to cable modem. Waited 30 - 40 seconds until internet service lights flickered green.
3b) Reconnected ethernet cable to MacMini and turned on power for MacMini. No Airport running. With administrator privilege I configured in Syst. Prefs. "Sharing" folder Internet access using "Built in Ethernet" port for computers running "Airport".
4) Turned Airport network on in MacMini and started browser.
Result: Internet connection established.
5a) Powered up PB G4 and then turned Airport on.
5b) In Syst. Prefs. in "Sharing" folder turned Internet Sharing off. But set "Share your connection from Airport" to computers using: Airport with check-mark. (No Built-in Ethernet and no Built-in FireWire!)
5c)Started browser. Result: Internet connection established.
6a) In the Finder window of both computers I clicked on "Go" in toolbar and looked for the name of the other computer, which were listed as alias besides the "Library" and "Servers" aliases. Clicking on the computer alias brought up the 'Networked Globe' and a control button "Connect".
6b) Clicking on "Connect" brought up the mounted drive of the other computer.
Result: Wireless network operational.
PS: I don't dare yet using encryption for the airport network. That's for another day.
Power Book G4, MacMini Mac OS X (10.4.7)

Airport Extreme off a Router which provides DNS - Guest Networks

Similar Messages

Maybe you are looking for