Airport Extreme - printing problems with window desktops

Hello everyone;
I a mac book and 3 more pcs (window) at home. I recently bought a airport extreme router in order to able to print from my mac book via wireless. everything is nice when I print from my mac book buy I'm not able to print from the pcs. This is annoying. I really need to get this working. Please send me step by step how to this thing works.
thanks,

Hey there BobKier,
It sounds like you have a printer connected to your Airport Extreme and you cannot print from it. I suggest the troubleshooting steps from the following article to help troubleshoot the printer:
USB printer troubleshooting for AirPort Express, AirPort Extreme, and AirPort Time Capsule
http://support.apple.com/kb/ts1253
Check for software updates
Be sure that you have the most recent OS X or iOS software updates, and the latest firmware for your AirPortproduct before trying to print.
Note: Printing via an iOS device requires an AirPrint enabled printer. Refer to AirPrint Basics for a list of AirPrint enabled printers.
Disconnect and reconnect
Disconnect the AirPort Express, AirPort Extreme or AirPort Time Capsule from a power outlet.
Turn off the printer.
Be sure the USB cable from the printer is connected to the AirPort Express, AirPort Extreme or AirPort Time Capsule.
Turn on the printer.
Reconnect the AirPort Express, AirPort Extreme or AirPort Time Capsule to a power outlet and wait for it to become ready.
Try to print.
Check your printer driver
Check the website of the printer's manufacturer for the latest driver version.
Reset Printing System
Use these steps on your Mac if the above steps do not help.
Open System Preferences > Print & Fax preferences.
Control-click or right-click in the Printers section on the left.
Choose Reset printing system....
Click OK.
Click the + button to add your printer again.
Try to print.
Still not working?
If your printer still doesn't work with AirPort Express, AirPort Extreme or AirPort Time Capsule printer sharing, but does work when directly connected to your Mac, contact the printer manufacturer for additional information and to verify that printer sharing is supported.
Additional Information
Refer to this article for additional help setting up a USB printer on your Wi-Fi network.
Thank you for using Apple Support Communities.
All the very best,
Sterling

Similar Messages

Airport Extreme Printing Problem with HP Deskjet.

Hello ... I wonder if any helpful folks can assist me with my printing problem? I am using Tiger on a new Intel imac with a HP Deskjet 960C. This printer is listed as having the latest drivers included within Tiger and works perfectly when connected via USB so my problem I guess is not with the software....I have disconnected everything and plugged everything back together again. I also deleted the printer from the printer list within the Printer Setup Utility application.... The imac recognisies the printer and upon pressing the print button everything feels as though its just going to work. The blue barber shop scroll appears but the printer fails to kick into gear and I get the big red exclamation mark appearing in the status box .... I would really love to try and sort this annoying error ... Any ideas? Thanks. Book G4 Mac OS X (10.4.4)

Hello jds17. Welcome to the Apple Discussions!
Unfortunately, not all USB printers are compatible with AirPort base stations.
Take a look at one of these iFelix Unofficial AirPort Printer Compatibility links, depending on which AirPort base station you have:
o 802.11g AirPort Extreme Base Station (AEBS) or AirPort Express Base Station (AX)
o 802.11n AirPort Extreme Base Station (AEBSn)
If your printer isn't listed, it doesn't necessarily mean it won't work, but simply that it has not been verified. iFelix also provides the following workaround for printers not on the list that would certainly be worth a try.
Also, you may find the following Apple article helpful.

I have an Airport Extreme, 2 laptops with windows 7 and a wireless HP printer. I can connect the laptops to the printer. Any advise?

I have an Airport Extreme, 2 laptops with windows 7 and a wireless HP printer. I am not able to connect the laptops to the printer. Any advise?

The problem is not the router.. the issue is the vpn has put your computer in a different IP range with a different gateway. When you turn off the vpn the computer returns to local lan and can print.
Some vpn software allows you to set gateway to use local net instead of remote gateway or access to other webistes or local lan.
Read up the issue.
http://stevejenkins.com/blog/2010/01/using-the-local-default-gateway-with-a-wind ows-vpn-connection/
Cisco vpn client..
https://supportforums.cisco.com/thread/239113
I did not search much.. just grabbed the first article I could find that explains the issue.
The whole point of the vpn is whilst it is connected your computer is NOT part of the Local Lan .. it is part of the Remote LAN via the vpn tunnel.
It is also a security risk using split tunnelling so often it will not be allowed.
Plug the printer directly into the computer via usb or whatever.. Local connection will work.. not local lan.

How can I set up the airport extreme base station with windows computer

how can I set up the airport extreme base station with windows computer

Hi - you need Airport Utility version 5.6.1 for Windows 7 - go to http://support.apple.com/kb/HT1547 to download it to your computer - the setup depends on what kind of modem you have and if you have another router connected - post back with this info to proceed - thanks

Printer Sharing with Windows Desktop

I wanted to share my HP Printer over the Wi-Fi network.
The printer is connected to my HP Pavilion Windows PC.
I added the network printer and when i print, it displays error message:
"Connection Error: NTSTATUS_BAD_NETWORKNAME"
How can i fix this problem?
Thanks!
P.S. I tried plugging the printer to my iBook directly via USB, and of course, it worked perfectly without installing any drivers. But it's nicer if i can print via network without pulling and plugging out cables everytime. Also, the iBook can "communicate" with my PC, as both can share files.

I've had a similar problem with my HP Printer, I don't get an error message printed but I do when I try to print- it just hangs. Again, when attached there are no probs and the iBook and desktop PC can communicate fine. I looked into it a bit more and found out that HP knew about the problem and were working on driver updates. It may be that this is the problem with your as well and until HP do something about it we're stuffed! Try going to the HP website and downloading the most upto date drivers for ur iBook and PC. It may help! Sorry to be the bringer of bad news!
Jack

Airport extreme configuration problem with Netgear DG834PN

Good morning,
I have a problem. I bought an AEBS via the WAN port to connect to my Netgear DG834PN.
I turned off the WiFi on the Netgear, I connected the AEBS in bridge mode, but with the iMac and other iDevice there are no problems.
On the contrary my Acer Travelmate (Win 7) does not want to connect ... fact is connected, the card tells me that is connected and has access to the internet, but does not show mewhen I browse any web page, Skype does not connect ...
Do you have suggestions for configuring the Netgear or dell'AEBS?

The Windows Firewall may be blocking the connection attempt. I have not used Windows 7, but on an XP machine, the Firewall settings are in the Control Panel. Check to see if this might be the case so you can "Allow" an "Exception".
The anti-virus software may also be blocking the connection. You may need to turn it off for the configuration, then turn it back on.
It will often help to try to configure the device using Ethernet, not wireless. Connect a spare Ethernet cable from your PC to one of the LAN <-> ports on the AirPort Extreme. Restart both the PC and AirPort Extreme, then open AirPort Utility again.
If still no luck, click the AirPort Utility File menu at the upper left hand corner of the screen and select Configure Other. Enter 10.0.1.1 into the address box and "public" (without the quotes) in the password box.

Airport Extreme Connection problem with new MacBook

Help-
For the past 2 years, I have had no problems with my Airport Extreme. My MacBook Pro (2006), My wife's iBook G4 and two AirPort Express units used as remote speaker connections have been rock solid. Both iPhone and one iPod touch work like a charm.
I just got my wife a new MacBook and since it came in and was connected, my Air Port Extreme has been nothing but a problem, requiring a hard reset every couple of days. As long as that MacBook is not connected, everything is fine.
Anyone have any ideas? Only the MacBook is using 802.11n. It is so frustrating, that my wife want to use her old iBook so if this can't get fixed, the MacBook is going back to Apple.

Welcome to the discussion area!
From your description, it sounds like the wireless communications between the AirPort Extreme and your wife's MacBook are picking up some sort of wireless interference from another source such as a cordless phone or another nearby security system.
I suggest that you try different channels for your wireless to see if you can find a setting with less interference. To do this, you would:
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme and then click Manual Setup below
Click the Wireless tab below the row of icons
Look for the Radio Channel or Channel setting
You may need to hold down the option key as you click on the selection box to display all available choices.
Start at the highest channel and work your way down, or start at the lowest and work your way up.
Click Update at the lower right of the window to save your current setting and the AirPort Extreme will restart in 20-25 seconds.
It will take some time to find the optimum channel for your network, so proceed slowly and take a few notes as you go.

Airport Extreme Utility problem with Vista (works with XP, MacOS)

Hi,
I just setup a new Airport Extreme network at my house, and most things are working fine. I have wirelessly connected at various points an Airport Express (using WDS), a MacBook Pro (OSX) and an IBM Thinkpad. I have several wired machines as well.
My problem: The wired machine I use to configure and setup everything is a Vista Ultimate machine. Unfortunately, the Airport Utility won't connect to the Airport Extreme (or Airport Express for that matter) from Vista. The utility works fine from XP or OSX, but not from Vista. Note that I'm using this in a wired capacity. The Vista machine is directly connected to the Airport Extreme, while several other machine are connected through a GBit switch.
Any help would be much appreciated? Is this a Vista security problem or an Airport Utility problem with Vista?

It's most likely a security issue with Windows Vista. Vista has the ability to set "compatibility modes" for applications.
Try:
1. right mouse clicking the Airport Utility's .exe file.
2. Click the Compatibility tab. Change the Compatibility mode to Windows XP (Service Pack 2).
3. Now go down to "Privilage Level" and check the "Run this program as an administrator"
Apple never tells you this but you must connect to the Airport Extreme wirelessly. Now run the Airport Utility. You should see it.

Airport Extreme printing problem w/ HP7 410 all-in-one

I just purchased a HP officejet 7410 all-in-one.
I can print using USB cable connected to printer.
However, I CANNOT print connecting the USB cable from printer to Airport Extreme and using Bonjour printing? The print job spools than just stops?
Any help would be appreciated....
macbook pro Mac OS X (10.4.8)

Hello HevnLgh,
Thank you for your input. I tried to follow your instructions but had trouble right from the start. I got to HP uninstaller and clicked continue but there was no printer listed. It just said "device" and uninstall was greyed out. I decided to just continue so I reset the printing system and repaired the disk permissions.
It took me a couple of tries to reinstall the printer from the Apple website because at first it couldn't find the device to add so I tried using the IP address on the next tab and that seemed to do something but it still wouldn't print. The printer was found after I went back and tried again and everything seemed to work this time (whew).
I tried the update procedure on the printer itself and it still can't connect with the server, but the original problem with the duplicate copy on shut down seems to have resolved itself.
The bottom line is my printer is working like it's supposed to (for now anyway) and I didn't get two copies of my printout so thank you again for your help. It's good to know I can go somewhere for help when I have a problem.

Airport extreme A1143 problem with mountain lion

what airport extreme software version works with mountain lion

I have an A1143 here and it works just fine with AirPort Utility 6.2 in Mountain Lion.
It also works fine with AirPort Utility 5.6, which I have on another Mac here.
All you can really do is try a Factory Default Reset on the AirPort Extreme to clear out all the old....and possibly conlficting.....settings and try to configure it again.
If you continue to experience problems, I would suspect a less than perfect AirPort Extreme....although I am sure that the seller claimed it was perfect.
Resetting an AirPort Base Station or Time Capsule FAQ
AirPort Extreme 802.11n (1st Generation) - Setup Guide

Airport express printing problem with Snow Leopard

I am no longer able to print to my shared printer after upgrading to Snow Leopard. I get a message that starts with "communication failure the computer is no longer able to communicate with your printer". My network consists of a dual-band Airport extreme and an Airport Express. The dual-band Airport Extreme creates the network and is connected to the internet. The printer (HP LaserJet 1012) is connected to the AirPort Express. The AirPort express joins the dual-band Airport extreme network for the sole purpose of turning the HP LaserJet 1012 into a shared wireless printer. Everything was working fine before the upgrade to Snow Leopard. When I connect the printer directly to my MAC via USB, it prints fine. I can "see" the printer fine through bonjour when it is connected to the AirPort express, but I get a failure whenever I try to print to it. I have tried plugging and unplugging the device. I have effectively redownloaded the print-driver by connecting the printer directly to my MAC. It sounds like a Snow Leopard bug. Any suggestions for a work-around? Thanks.

I upgraded to Snow Leopard and had difficulties connecting to my HP Photosmart 7150 printer through Airport Express. Apple setup found a 3rd party printer driver by Gutenprint, which I downloaded and the printer works. But like it did under Leopard. Under the 10.5 OS, a print command would send a wake up signal to the HP, which automatically turned off after a period of idleness, and then print. Under 10.6, there is no wake up and I need to manually activate the printer. I went to the HP web site hoping to find a "new" driver for 10.6 and HP has posted a message saying it does not and will not be providing print driver for 10.6. It then has a long list of HP devices that cannot or will not print with Snow Leopard. So those with no-printing issues should check your model against the HP driver listing. I believe this is a neat way for HP to force Mac users who upgrade or install 10.6 to buy a new printer for which HP has a 10.6 driver. At least I can print and the only inconvenience that I can see if the lack of that wake up signal. My wife says it won't hurt me if I have to get up and walk to the room with the printer to turn it on!

Printing problem with Windows : Win32PrintService

Hi,
I wrote a program which I run under Windows, and prints a .gif image with some text.
I have tested it vith various printers, and it works well.
But with a specific printer (Datamax Allegro, driver by Seagull) I get this exception :
java.lang.ArrayIndexOutOfBoundsException
at sun.print.Win32PrintService.getDefaultAttributeValue(Win32PrintService.java:785)
at sun.print.Win32PrintJob.printableJob(Win32PrintJob.java:414)
at sun.print.Win32PrintJob.print(Win32PrintJob.java:343)
I have downloaded the whole source for j2sdk 1.4.0, but did not find the source for
Win32PrintService and Win32PrintJob, so I can not run it in debug mode
Does anyone know where I can find that source ,
... or has any idea on how to avoid that exception ?
Thanks for any advice
Michel Clabon
[email protected]

Hi,
But with a specific printer (Datamax Allegro, driver
by Seagull) I get this exception :
java.lang.ArrayIndexOutOfBoundsExceptionHi have the same problem with a Seiko smart label printer 240
I have downloaded the whole source for j2sdk 1.4.0,
but did not find the source for
Win32PrintService and Win32PrintJob, so I can not run
it in debug mode
Does anyone know where I can find that source ,j2se\src\win32\classes\sun\print\Win32PrintService.java
AFAIR you have to download the sources separately somewhere from sun.
... or has any idea on how to avoid that exception ?it tries to access an elment of a non-existing array.
(guessing: the array should contain some media information and the printer driver does not report any media data?)
from memory, something like:
aset.add(MediaSize.ISO_A4);
may help, if this does make sense for you.
I posted a bug to sun, so lets wait and see...

Network Printing Problems with Windows 8.1 and HP 8600 Officejet Pro

I can not print or scan from my Dell 2720 after the system has gone to sleep. My printer shows as connected to my network. Most time I have to completely restart my PC to get it to work but even that doesn't correct the issue most time. I have removed and reinstalled the printer at least a dozen times and updated the drivers several times. Also another oddity - my router is a dual-band (2.4 & 5 GHz) and my printer only connects to the 2.4 GHz connection which I understand is normal but any device attempting to print must be connect to the 5GHz band or nothing will print. So essentially I have two problems. Any suggestions?

Hi @mhmost,
I would be happy to help you print to your 8600. Running the Print and Scan Doctor might help. The HP Print and Scan Doctor is a free utility (tool) that helps to quickly resolve common printing, scanning and connectivity issues including but not limited to:
Connectivity:
USB: Verifies that the USB connection from your computer to the HP product is working correctly.
Network: Verifies that the network connection between your computer and your network is working correctly.
Device Status Test: Checks for device errors such as out of paper, paper jams, carriage stalls, and paper feed issues, and then provides instructions for fixing the error.
Driver Check: Checks for missing or corrupt driver files.
Device Manager: Checks for problems in Device Manager that would prevent printing.
Device Online: Checks if the product has been paused or set to offline, and then sets the status back to online if necessary.
Print Queue: Checks for and clears pending print jobs in the print queue (a log of print jobs waiting to print).
Port Match: Checks the port settings for the HP product.
Device Conflicts: Checks for conflicts with other drivers, such as other printer brands.
Ink Issues: Checks the cartridges and ink levels for issues that affect print quality.
Print Settings: Checks and adjusts the print quality settings.
Test Print: Prints a test page for print quality evaluation, and provides options for cleaning and aligning the printhead if necessary.
Scan Tests: Checks the scan mechanism, drivers, and registry entries.
Source:Try the HP Print and Scan Doctor for Windows
Click here to download and run the Print and Scan Doctor> >>>>> www.hp.com/go/tools
If that does not resolve the issue, post back and let me know if there are any symbols other than green check marks and what they are next to of course. The wrench is not always easy to spot as the wrench and the check mart are in the green circle.
If you see only green check marks (), the tool did not find any problems.
If you see green wrenches (), the utility identified an issue and corrected it automatically.
If you see yellow exclamation points (), the test failed and required user action, but the step was skipped.
If you see a red X (), follow the on-screen instructions to resolve the issue.
As for the frequency, you are correct, the printer will not work over the 5.0GHz frequency, only with the 2.GHz.I suggest disabling the 5.0 frequency, and running on only the 2.4.
Thanks, I look forward to hearing back from you.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Airport Extreme Base Station with HP Printer problems

I have a pretty old HP all-in-one (G55) printer/scanner/copier device. Plugging it into my AEBS seems to not let me print to it. I have the most recent driver from HP.
Do you think it's my setup, or is the AEBS somehow not compatible with the older HP devices?
Also, is it possible to fax, scan, etc through an all-in-one device plugged into an AEBS?

I have a pretty old HP all-in-one (G55) printer/scanner/copier device. Plugging it into my AEBS seems to not let me print to it. I have the most recent driver from HP.
Do you think it's my setup, or is the AEBS somehow not compatible with the older HP devices?
No the problem is with the HP driver.
Try using the HPIJS drivers.
For those with the older base station.
Use the process outlined here:
HP Printers (and others) not on compatibility list and Airport Extreme Printing
http://tech.ifelix.net/1300.html
Also, is it possible to fax, scan, etc through an all-in-one device plugged into an AEBS?
No, not via the USB port.
Can I scan using my all-in-one when it is connected to the USB port of an Airport Express or Airport Extreme Base Station?
http://discussions.apple.com/thread.jspa?messageID=610763&#610763

Airport extreme base station with Hp 3210 all in one printer

Just bought and hooked up the above. Using with iBook G4. Still dealing with dial-up unfortunately, but got online just fine. When I tried to print on the above, it immediately dialed up when I hit "print". ?? What's going on?

I have a pretty old HP all-in-one (G55) printer/scanner/copier device. Plugging it into my AEBS seems to not let me print to it. I have the most recent driver from HP.
Do you think it's my setup, or is the AEBS somehow not compatible with the older HP devices?
No the problem is with the HP driver.
Try using the HPIJS drivers.
For those with the older base station.
Use the process outlined here:
HP Printers (and others) not on compatibility list and Airport Extreme Printing
http://tech.ifelix.net/1300.html
Also, is it possible to fax, scan, etc through an all-in-one device plugged into an AEBS?
No, not via the USB port.
Can I scan using my all-in-one when it is connected to the USB port of an Airport Express or Airport Extreme Base Station?
http://discussions.apple.com/thread.jspa?messageID=610763&#610763

Airport Extreme - printing problems with window desktops

Similar Messages

Maybe you are looking for