Airport Extreme setup issue- Please help!

Hi,
I recently replaced our old router with an Airport Extreme. My HP Laptop has and 802.11 b/g Atheros wireless in it and i can get a 'Local only' connection. I read through help and tried to do the "allow client access to network" instructions, but there is not an option to "Add Wireless Clients" on the Base Station menu they refer to in the help instructions. I have tried using another laptop to access internet wirelessly, and it had no problem. Any help please or can you please refer me to corrected instructions? Thanks in advance.

Hello Andy Castillo. Welcome to the Apple Discussions!
I've used WPA/WPA2 Personal and the internet seems slower - like dial-up.
Unfortunately, the trade-off of using wireless encryption is the overhead that is required will reduce the overall bandwidth ... but it shouldn't do so dramatically. For example, my MacBook connects to a similar AirPort Extreme averaging around 270+ Mbps. Granted, to get that bandwidth, I typically use my MacBook in the same room as the Extreme, but I am using WPA2 Personal for encryption ... just to show that it is possible to achieve high bandwidths.
I clicked on 5ghz and that seemed better, but kept reverting back to Extreme without the 5ghz.
This would tell me that either the distance between the Mac and the Extreme is just out of the 5 GHz range or that there is some type of Wi-Fi interference preventing the Mac from getting a strong signal. As you know, the higher frequency radio offer greater speed, but less range.

Similar Messages

Airport Extreme / USB Disk - please help!

I have an Airport Extreme which is connected to my PC running Vista, and provides wireless access to my iMac.
Recently bought a new 2TB external hard drive. Partitioned it 3 ways - one partition was set up as HFS+ to back up my Mac using Time Machine, the other two partitions were set up as FAT32 to back up the PC and provide additional storage that would be accessible to both.
After formatting, connected to the Airport extreme, and was able to see all 3 partitions of the drive listed. Set it up to enable file sharing secured with accounts. Was able to get the Mac to connect to the drive and run Time Machine flawlessly over wireless. However, whenever I access the other disks through the PC, it is intolerably slow, with most attempts to move files onto the disk failing or timing out. Not sure what might be wrong - tried turning off Windows Firewall, but that doesn't help. Tried all different disk security settings too. Really want to be able to use this disk on both the PC and the MAC without having to disconnect from my network and hook it up directly. can anyone offer some advice or suggestions as to how I can get Windows to play nice with the disk connected to Airport?

FundRopher wrote:
one partition was set up as HFS+ to back up my Mac using Time Machine
I hate to have to tell you this, but backing-up that way is "iffy" and +*not supported by Apple.+* See [Using Time Machine with an Airport Extreme Air Disk|http://web.me.com/pondini/Time_Machine/Airport.html] (or use the link in *User Tips* at the top of this forum).
This forum, and the Time Machine forums, have many, many posts about it working for some number of days, weeks, or even months, then the backups suddenly turn up corrupted, often beyond repair.

How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

Once you have the drive connected to your Mac, click System Preferences (gear icon) on the dock
Click Time Machine
Click Options
Be default, the hard drive will be Excluded from backups. Click the drive to highlight it, then click the "-" (minus) button at the bottom of the list to remove the drive from Excluded items.
The drive will be backed up on the next Time Machine pass
Everything above assumes that the hard drive has been formatted in Mac OS Extended (Journaled) as Time Machine will only backup drives in that format.

HP LaserJet Pro MFP M125nw Driver Setup Error - Please Help - I can't Use My Printer

Hi,
I have just bought a new HP LaserJet Pro MFP M125nw Printer. But I can not install it. I can't use it, even one page written document.
This is the error when setup appears:
Please help me...

Hi @NafirKeyh ,
I see that you are experiencing issues installing the printer on Windows 7. I would really like to be able to help you resolve this issue.
Try these steps to see if it will resolve the issue. Disabling the Startup programs and temporarily turn off the Antivirus Software should prevent any interference during the installation.
Fatal Error 'Error 1603. A fatal error occurred during installation' (MSI Error 1603) Displays Durin...
How is the printer going to be connected? (USB/Ethernet/Wireless)
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Mid 2010 15" MBP i5 A1286 POWER ISSUE-PLEASE HELP-

The MBP works fine when mains connected but the only issue is every time I take the charger out it shuts down on me!!! So I have checked with a multitester & looks good the only thing i find hard to check for power is the battery itself as its hard to get a good connection, also I took to local Apple store & they checked with a new battery but said its still same issue so the guy disconnected nearly all the connecters off to check if they causing issue & he said now the battery is charging.
So they still have the laptop to do further tests etc, but I’m not sure what could be the problem hear as maybe there is some component which is bad so the battery’s not charging or what else could be the issue please help & advice as I’m really confused as if it was something to do with the logic board then surely it would not even charge even after checking with the multitester or like Apple genius done by disconnecting other components...
ANY HELP OR ADVICE WOULD BE HELPFULL,
THANKS GUYS

THANKS FOR THE HELP GUYS!!! BEEN AROUND 5 DAYS & NOT ONE PERON HAS HELPED...
BUT YEAH THANKS AGAIN...
WASTE OF TIME THIS IS...

Trackpad Issue - Please Help!

Hi there,
Hope you can help me out here.
I've recently purchased a 15" i7 Macbook pro. The machine is but 3 weeks old &, of course, very well looked after.
A few days ago, the built-in trackpad started behaving eratically. Cursor moving by itself, not responding to touch, clicking and opening things involuntarily. Not good at all. Many users seem to have had this exact same issue.
These problems seemed to miraculously stop after a few re-boots and possibly a software update? I really couldn't tell you what resolved the problem.
Unfortunately I now have a totally different problem.
There is a thin, possibly 8 to 10mm horizontal strip across the centre of the trackpad that no longer responds to touch. If I move my finger from the botom of the trackpad upwards (or vice versa), the cursor will stop momentarily as it passes over the horizontal strip. The buttons are fine and the rest of the trackpad is fine. For the moment, I've increased the cursor acceleration so that I can at least navigate round the screen with a smaller area of the trackpad. USB magic mouse seems to work fine.
If anyone else has experienced this &/or found a solution for this issue, please help me out here. I have rifled through endless threads about MBP trackpad issues with little success & do not live close to an apple store/genius bar.
This is a 3 week old machine that cost me a small fortune. To be getting software/hardware issues so early on in it's lifespan is really rather worrying for the future.
Appreciate your help here.
J

I'm not sure what caused this, but I extended my lunch break and drove the machine down to the Westfield apple store. I didn't have an appointment with the Genius Bar but I managed to persuade one of the staff to speak to a technician in the workshop. She came back into the store and told me that they had replacement trackpads and that , considering the machine was only 3 weeks old, the technicians kindly sandwiched the repair into their timetable at zero cost. 2 Hours later, I now have a perfectly functioning trackpad/machine.
I can't thank them enough.
My only gripe is that I couldn't speak to a technician to find out what the problem was, how they resolved it or what causes these issues for future reference. Understanding why these problems occur often helps to build your own framework of understanding. Most of the threads i've read about trackpad issues are largely unresolved with people only speculating the problem/solution.
The initial issue I had with the trackpad's erratic behaviour seemed to be a well known problem that many are associating with a trackpad firmware update. Unless by pure coincidence I had an immediate & major hardware fault after it, which is unlikely, my personal guess is that the two issues were related.

Transport Issue Please help

Hello,
I have got a major prolen during transport.
I have GEMPLOYE1 Which is a time dependient master data. which has Attribute called 0COUNTRY_ID.
I have a custome attribute Called Actual PSGroup/Grade GPAYSCGR which has a compounpunding attribute 0COUNTRY_ID
Now when I am trying to transport PSGroup/Grade GPAYSCGR to QA that transport is failing , the log massage is
Characteristic GEMPLOYE1: Attribute GPAYSCGR compounded to 0COUNTRY_ID has a diff. time-dpdncy
If any one saw this issue, please help me to fix the same.
Samit

Hi Venu,
We can't add authorisation objects on Individual servers.We need to add authorisations on BWD ie Dev system and transport to BWI QUA system.This is the Process we need to follow as per our rule set.
So,As the problem mentioned above if i add some auth. objects on BWD DEV system and transport it to BWI QUA system,it is getting transported Successfully to BWI,but the auth.objects what i have added on BW DEV system is not found on BW QUA system.
What could be the problem for that,Is that the problem with transports like TP error or is it related with some tables of auth.objects...................
Could u please analyse the problem and tell me the solution for this..........
Thanks Much
Swapna.D

Headerrenderer issue -Please help

Headerrenderer issue -Please help
hi
I have a datagrid and I am doing a custom sorting on the grid(by getting data from DB).
I achieve this by capturing the headerrelease event of datagrid .In thee venthandler I will query from DB and do event.preventdefault to prevent standard grid sorting.
Now I need to display my own custom ascending/descending arrows in the header.i have created an header renderer for this,
In the headerrenderer I am lsitening to the headerrelease event of datagrid and in the eventlistener, as per the sortfield, i am trying to make the sort arrow visible/invisible.
But somehow making the sort arrows visible/invisible is not working.The initial arrow works fine.it is shown the correct column(Name) as done in the init() method.
The eventhandler is invoked on clicking the column headers and all the alerts are shown.
Please see the headerrenderer code below and help me.(code is not complete only the relevant part is included)
<?xml version="1.0" encoding="utf-8"?><mx:HBox
xmlns:mx="http://www.adobe.com/2006/mxml" width="100%" height="100%" horizontalScrollPolicy="off" creationComplete="init()" implements="mx.controls.listClasses.IDropInListItemRenderer">
public function init():void{
headerLabel = dataField.label;
_dataGrid.addEventListener(DataGridEvent.HEADER_RELEASE,sortChanged,false);
if(_dataField.localeCompare('Name')==0)asc.visible=true; }
private function sortChanged(e:DataGridEvent){
var dg:DataGrid=e.currentTarget asDataGrid;
varcolumn:DataGridColumn = DataGridColumn(e.currentTarget.columns[e.columnIndex]);if(_dataField.localeCompare(e.dataField)==0)
if(asc.visible ||(!asc.visible&&!desc.visible))
Alert.show(
'in..');
asc.visible=false;
desc.visible=true;
else if(desc.visible){
asc.visible= true;
desc.visible=
false;
else{
asc.visible=
false;
desc.visible=
false;
]]>
</mx:Script>
<mx:Text text="{_headerLabel}" />
<mx:Image source="{ascIcon}" id='asc' visible="false">
<mx:Image source="{descIcon}" id='desc' visible="false"/>
</mx:HBox>

I got the solution!!
i need to assign the headerrendereer to the columns dynamically inorder for this to work:
if anybody wants to know details of solution let me know

Airport Extreme setup problems on existing WDS network - Please help!

I just bought a Time Capsule and have setup a WDS network for the house. The Airport Express joins the network just fine as a remote WDS device. I cannot get the Airport Extreme (v5.7) to join the same network. It just continues to make a *separate network with the same name* despite the Channel being the same, the WDS being set to remote, and the main ID of the Time Capsule has been put in correctly. In other words, since I setup the airport Express correctly, I cannot figure out for the life of me why the Airport Extreme is not joining correctly.
PLEASE HELP. I've been trying this for 6 hours now and countless total restarts by hard resets of all the equipment.

Hello arthung. Welcome to the Apple Discussions!
Let's double-check your WDS setup ...
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. Also, jot down the AirPort IDs for each of the base stations to be used in the WDS.)
o Perform a "hard" reset on the Time Capsule (TC) and a "hard" reset on the 802.11b/g AirPort Extreme Base Station (AEBS).
Main Base Station Setup - TC
o Click the AirPort status menu in the menu bar and choose the wireless network created by the TC.
o Open AirPort Utility.
o Select the TC, and then, choose Manual Setup from the Base
Station menu.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the AirPort ID of the AX.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup - AEBS
o Click the AirPort status menu in the menu bar and choose the wireless network created by the AX.
o Open AirPort Utility.
o Select the AX, and then, choose Manual Setup from the Base Station menu.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of the main base station in the WDS Main field.
o Click Update to transfer the settings to the base station.
(ref: Pages 42-46 of "Designing AirPort Networks.)

Time Capsule & Airport Extreme Speed Issues

Hello everyone!
I hope to be able to have a solution to my home network problems..??!! (hopefully!)
My Home Network Setup & Problem
I have my ADSL modem hard wired into a 1st generation Airport Extreme, I also have a 3rd Generation 2TB TimeCapsule extending the wireless network.
One iMac & one MacBook Pro (new(ish) ones) use the network for home use.
All softwares and firmwares are upto date. My house is relatively small with excellant wireless coverage throughout.
My problem is that when I transfer files wirelessly across the network either to my TimeCapsule or computer to computer it peaks at about 2mb/sec and is "sporadic" at best!
I monitor the wireless traffic with iStat Pro and see a graph which goes up and down continuously, it obviously is not happy. The same happens with downloads from the web but this might not be a network issue, but maybe it is?
It is not normal to wait 4hrs for a 7Gb transfer, surely!!
Any suggestions would be most helpful. I've reset everything, started from scratch and had no success. I can answer any questions you may need to know to help with this, i'm not an expert with computers but I have an alright knowledge.. Please don't confuse me with too much technical lingo but I understand the basics!!
All machines have OSX Lion also
Matt

Possibly, but I would venture to guess that the TC is not in the optimal location to maintain the highest data transfer rates on the extended network with the AEBSn.
To help locate where that would be, we will need to make Signal-to-Noise Ratio calculations to measure the signal quality of the AEBSn at the location the TC.
SNR (in dB) = Signal (in dBm) - Noise (in dBm)
You can easily find the Signal and Noise value using System Profiler on your Mac laptop.
ref: Click on the Apple icon on the menu bar > About This Mac > More Info... > Contents > Network > AirPort > Interfaces > en1 > Current Network Information > Find your wireless network > Signal / Noise
While your still in the System Profiler, note the value for Transmit Rate.
These values should be negative numbers. For example, mine currently read: -67 dBm / -95 dBm, with a transmit rate of 27 (Mbps). Plugging in these numbers yield: SNR = -67 - (-95) = 28. My Mac Mini is about four rooms away from my AEBS with about five walls between them. As you can see, the signal is still quite useable ... but the bandwidth is minimal, especially for streaming.
SNR Guideline
40dB+ SNR = Excellent signal
25dB to 40dB SNR = Very good signal
15dB to 25dB SNR = Low signal
10dB to 15dB SNR = Very low signal
5dB to 10dB SNR = No signal
Again, what we are interested in is the SNR value of the AEBSn at the current location of the TC. Since we only want to measure the AEBSn, you will need to (temporarily) power-down the TC. With your MBP near the TC, take the signal & noise measurements. Since we are trying to find the best location for the TC, move the MBP to the next possible location that you can place the TC and take the same measurements. Repeat this as many times as you require to build a good sampling of data for different potential locations. Now that you collected the data, plug them into the SNR formula to come up with the SNR value. Note these values and determine which location provides the highest SNR value ... this, theoretically would be the best location of the TC. You will want SNR = or greater than 25dB.

Airport extreme connection issues

Yesterday, I bought a new Comcast-compatible modem (Motorola SB5101) and an airport extreme. These replaced an old (5 years or so) SB5101 and an equally-old airport express, which was too old for my new MacBook Pro to be able to manage it through airport utility.
I replaced both components because I got sick of my internet connection dropping constantly, many times a day for the last few years. (I know, but it's true!)
Comcast insists that the signal coming into the house is fine and is constant, so it's not the ISP dropping the connection.
The cable comes into the house, into the modem. Ethernet goes from the modem into a Sprint AirRave (Sprint says that must be how it's set up). From the AirRave, the ethernet goes to the airport express. From there, I can connect computers and devices wirelessly, but from the airport express, an ethernet also goes into my home distribution panel, so that in each room of the house you can plug directly into the ethernet (about 8 outlets).
The problem happens whether or not the AirRave is installed.
Sometimes the connection drops for a few seconds and re-connects. Most often when it drops, and I go into Network Preferences Diagnostics, Wi-Fi = green light; same with Wi-Fi Settings, Network Settings, and ISP. But Internet and Server = yellow.
Sometimes running the diagnostic fixes it and it re-connects. Other times you must reset the airport and/or the modem. Sometimes it will not re-connect even after multiple times re-setting those deivces.
Since installing the airport extreme yesterday, sometimes I get a message on my Macbook Pro that says my MAC address is being used by another device (?).
I have no knowledge about networks AT ALL, no idea how my computer can have the same MAC address as anything else, no idea what specific settings I should be using -- I always have let the setup happen automatically.
If anyone has any idea how to solve this I'd be very grateful. I'm not sure whether I've given enough details, like I say I lknow NOTHING about how to set up a Network.
It was a nightmare setting it up yesterday, once I got it up according to instructions, I was in an endless loop -- every time I tried to open a page in my browser, I was taken to the Comcast Setup page instead, asking for my phone number and account number. Entering this took me to a new page saying "unable to connect with our system." I was on the phone with Comcast forever trying to fix it, resetting the modem and airport over and over again. Eventually somehow it worked, but later that night (and again already this morning) the connection has dropped a number of times.
I thought getting new components would fix the problem, now I'm so frustrated I don't know what to do.
Anyone?
Thanks!!
-- Craig.

Since installing the airport extreme yesterday, sometimes I get a message on my Macbook Pro that says my MAC address is being used by another device (?).
This usually indicates that there may be something amiss with the NAT service or that each network client cannot access it properly.
To verify that the 802.11n AirPort Extreme Base Station (AEBSn), Motorola modem, or Internet service is NOT the issue, we will temporarily remove the AirRave from the network equation.
To do so, please power-down the modem, AirRave, AEBSn, and computer(s). While they are all powered-down, disconnect the Ethernet cable going to the AirRave.
Next,
Disconnect the AirPort base station from the AirRave and Ethernet distribution patch panel.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Temporarily connect the Ethernet cable coming from the modem to the WAN port of the AEBSn.
Reconnect the Ethernet cables coming from the AEBSn's LAN ports to the Ethernet Distribution Patch Panel.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Airport extreme hub -- lost password help

My husband set up our new Airport Extreme a few weeks ago and things worked fine. The device recognized our printer, and we had no issues -- other than the scanner didn't work with the printer.
I resolved the print issue by downloading a new driver, but when I did that (it required removing all printer info from the computer and then doing a clean install), the reinstall wiped our printer out of the Airport Extreme configuration.
No biggie. I'd run the Airport Extreme share-USB-printer procedure again.
No go. My husband either mistyped or cannot remember the password to the hub, so not only can I not upgrade the Airport Extreme, I can't do anything with it. At all.
Does anyone know what I should do? I'm an admin on this computer, so I should be able to do what's necessary; I just don't know what that is.
I am also a new Mac user (new in December, after decades on a PC), so a resolution isn't coming readily to mind, and I would appreciate any help I can get. We only bought a service plan for our iMac, so the apple store wasn't much help, either.

Ah, never mind.
I just discovered the Airport Extreme user guide online, and I think I have what I need. Apparently I can reset the system with a paper clip. Of course I can't find a single paper clip in the house. <sigh>

MBP running at a snail's pace, and a myriad of other interrelated issues, please help :'-(

Hello, my MBP is running very slowly, MS Office for Mac constantly freezing, Safari constantly freezing, various little issues are arising with many different functions/programs when I try to use them; i.e., the enter key will just stop working in Excel or my Adobe Acrobat will shut itself down out of nowhere, Finder freezes and/or won't relaunch; these are just a few examples, but the overall theme is that I am experiencing problems in usability and functionality with my MBP across the board. There is no rhyme or reason to any of it, and all programs and apps seem to be affected. I first began noticing the problems upon installation of the Yosemite upgrade so initially thought that was the issue, but I have since found that malware items have added themselves to my Safari extensions. I found instructions to remove them entirely, but could not find them anywhere on my computer other than the Safari extensions when I followed the steps provided. I tried clicking "uninstall", but had no luck, which is not surprising since I am pretty sure the "uninstall" option listed with the extension is just part of the malware. I have "disabled" the extensions, but that didn't do anything. I'm sure that they have implanted themselves elsewhere and are lurking in the shadows of my operating system and wreaking havoc throughout my computer.
The whole situation is making it extremely difficult to get anything done, and if I don't fix it soon it is going to be the major contributing factor to my complete mental collapse.
PLEASE HELP!!!
I tried to find suggestions in other areas of the Apple Support Community, and found the EtreCheck tool in one of the discussion threads. I ran the report on my system, and it looks like my MPB is riddled with problems. I don't even know where to begin in order to correct them. I am not sure if the malware has just taken over and is behind all of these, or if I am dealing with several different sources of trouble.
Any help with this would be much appreciated, the EtreCheck report is as follows:
Problem description:
MBP usability decreased significantly after installing Yosemite. Computer constantly freezing and completing any task in any program/using any function of MBP takes 5-10x as long as it used to.
EtreCheck version: 2.1.8 (121)
Report generated February 8, 2015 at 7:53:07 AM EST
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
    MacBook Pro (13-inch, Late 2011) (Technical Specifications)
    MacBook Pro - model: MacBookPro8,1
    1 2.4 GHz Intel Core i5 CPU: 2-core
    4 GB RAM Upgradeable
        BANK 0/DIMM0
            2 GB DDR3 1333 MHz ok
        BANK 1/DIMM0
            2 GB DDR3 1333 MHz ok
    Bluetooth: Old - Handoff/Airdrop2 not supported
    Wireless: en1: 802.11 a/b/g/n
    Battery Health: Normal - Cycle count 364
Video Information: ℹ️
    Intel HD Graphics 3000 - VRAM: 384 MB
        Color LCD 1280 x 800
System Software: ℹ️
    OS X 10.10.1 (14B25) - Time since boot: 4 days 17:53:1
Disk Information: ℹ️
    ST9500325ASG disk0 : (500.11 GB)
        EFI (disk0s1) <not mounted> : 210 MB
        Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
        Macintosh HD (disk1) / : 498.88 GB (332.61 GB free)
            Encrypted AES-XTS Unlocked
            Core Storage: disk0s2 499.25 GB Online
    MATSHITADVD-R   UJ-8A8
USB Information: ℹ️
    Apple Inc. FaceTime HD Camera (Built-in)
    Apple Inc. BRCM2070 Hub
        Apple Inc. Bluetooth USB Host Controller
    Apple Inc. Apple Internal Keyboard / Trackpad
    Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
    Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
    Mac App Store and identified developers
Kernel Extensions: ℹ️
        /Applications/Kies.app
    [not loaded]    com.devguru.driver.SamsungACMControl (1.4.26 - SDK 10.6) [Click for support]
    [not loaded]    com.devguru.driver.SamsungACMData (1.4.26 - SDK 10.6) [Click for support]
    [not loaded]    com.devguru.driver.SamsungComposite (1.4.26 - SDK 10.6) [Click for support]
    [not loaded]    com.devguru.driver.SamsungMTP (1.4.26 - SDK 10.5) [Click for support]
    [not loaded]    com.devguru.driver.SamsungSerial (1.4.26 - SDK 10.6) [Click for support]
        /Library/Extensions
    [loaded]    com.sophos.kext.sav (9.2.50 - SDK 10.8) [Click for support]
    [loaded]    com.sophos.nke.swi (9.2.50 - SDK 10.8) [Click for support]
Problem System Launch Agents: ℹ️
    [killed]    com.apple.CallHistoryPluginHelper.plist
    [killed]    com.apple.CallHistorySyncHelper.plist
    [killed]    com.apple.cmfsyncagent.plist
    [killed]    com.apple.coreservices.appleid.authentication.plist
    [killed]    com.apple.EscrowSecurityAlert.plist
    [killed]    com.apple.Maps.pushdaemon.plist
    [killed]    com.apple.rcd.plist
    [killed]    com.apple.recentsd.plist
    [killed]    com.apple.SafariNotificationAgent.plist
    9 processes killed due to memory pressure
Problem System Launch Daemons: ℹ️
    [killed]    com.apple.AssetCacheLocatorService.plist
    [killed]    com.apple.awdd.plist
    [killed]    com.apple.coresymbolicationd.plist
    [killed]    com.apple.ctkd.plist
    [killed]    com.apple.emond.aslmanager.plist
    [killed]    com.apple.GSSCred.plist
    [killed]    com.apple.ifdreader.plist
    [killed]    com.apple.installd.plist
    [killed]    com.apple.nehelper.plist
    [killed]    com.apple.periodic-monthly.plist
    [killed]    com.apple.periodic-weekly.plist
    [killed]    com.apple.sandboxd.plist
    [killed]    com.apple.softwareupdate_download_service.plist
    [killed]    com.apple.tccd.system.plist
    [killed]    com.apple.wdhelper.plist
    15 processes killed due to memory pressure
Launch Agents: ℹ️
    [not loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
    [running]    com.adobe.AdobeCreativeCloud.plist [Click for support]
    [running]    com.canon.MFManager.plist [Click for support]
    [unknown]    com.oracle.java.Java-Updater.plist [Click for support]
    [running]    com.sophos.uiserver.plist [Click for support]
Launch Daemons: ℹ️
    [loaded]    com.adobe.fpsaud.plist [Click for support]
    [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
    [unknown]    com.oracle.java.Helper-Tool.plist [Click for support]
    [running]    com.sophos.common.servicemanager.plist [Click for support]
User Launch Agents: ℹ️
    [loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
    [loaded]    com.adobe.ARM.[...].plist [Click for support]
    [loaded]    com.divx.agent.postinstall.plist [Click for support]
    [loaded]    com.kodak.KODAK AiO Firmware Updater.plist [Click for support]
    [loaded]    com.kodak.KODAK AiO Software Updater.plist [Click for support]
    [running]    com.kodak.StatisticCollection.plist [Click for support]
User Login Items: ℹ️
    iTunesHelper    Application Hidden (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
    Dropbox    UNKNOWN (missing value)
    bomgar-scc-20140103-113305    UNKNOWN (missing value)
    KiesAgent    Application Hidden (/Applications/Kies.app/Contents/MacOS/KiesAgent.app)
    fuspredownloader    Application Hidden (/Users/[redacted]/Library/Application Support/.FUS/fuspredownloader.app)
Internet Plug-ins: ℹ️
    AmazonMP3DownloaderPlugin1017277: Version: AmazonMP3DownloaderPlugin 1.0.17 [Click for support]
    OVSHelper: Version: 1.1 [Click for support]
    Default Browser: Version: 600 - SDK 10.10
    AdobeExManDetect: Version: AdobeExManDetect 1.1.0.0 - SDK 10.7 [Click for support]
    AdobeAAMDetect: Version: AdobeAAMDetect 2.0.0.0 - SDK 10.7 [Click for support]
    AdobePDFViewerNPAPI: Version: 11.0.10 - SDK 10.6 [Click for support]
    DivXBrowserPlugin: Version: 2.2 [Click for support]
    FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
    Flash Player: Version: 16.0.0.305 - SDK 10.6 [Click for support]
    QuickTime Plugin: Version: 7.7.3
    Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Click for support]
    SharePointBrowserPlugin: Version: 14.4.7 - SDK 10.6 [Click for support]
    AdobePDFViewer: Version: 11.0.10 - SDK 10.6 [Click for support]
    CANONiMAGEGATEWAYDL: Version: 3.2.0.1 - SDK 10.6 [Click for support]
User internet Plug-ins: ℹ️
    WebEx64: Version: 1.0 - SDK 10.5 [Click for support]
    Google Earth Web Plug-in: Version: 7.1 [Click for support]
Safari Extensions: ℹ️
    Saveonmac
    iMedia Converter Deluxe
    MacVeXe
    DivX Plus Web Player HTML5 <video>
3rd Party Preference Panes: ℹ️
    DivX [Click for support]
    Flash Player [Click for support]
Time Machine: ℹ️
    Time Machine not configured!
Top Processes by CPU: ℹ️
        16%    WindowServer
        11%    SophosAutoUpdate
         8%    com.apple.WebKit.Plugin.64
         8%    Safari
         2%    SophosUIServer
Top Processes by Memory: ℹ️
    120 MB    Safari
    116 MB    SophosWebIntelligence
    43 MB    SophosScanD
    43 MB    InterCheck
    39 MB    WindowServer
Virtual Memory Information: ℹ️
    44 MB    Free RAM
    751 MB    Active RAM
    724 MB    Inactive RAM
    1.21 GB    Wired RAM
    60.34 GB    Page-ins
    819 MB    Page-outs

The minimum requirement is 2GB, but most people think 4GB is the bare minimum.
I primarily buy from Crucial, Other World Computing, or MemoryTen. As long as they have a "configurator" where you pick you exact Mac from a list and it lists all the compatible memory for that Mac, AND it has a lifetime warranty on the RAM, it should be ok. Macs are very picky about the RAM because they use it to its full capacity. If there are any faults in the modules, it will crash.
There are suggestions for sites in other parts of the world on the EveryMac website. Look down in the Section for RAM where you'll find links to their sponsors (OWC is the US-based one).
In Apple's world, there is a difference between and "Upgrade" and an "Update." Updates should generally be installed as they patch vulnerabilities and fix bugs.
Upgrades on the other hand are an entirely new Operating System (OS). A change in the OS can cause many problems with your installed software as it may not be compatible with the changes. It may rely on programming interfaces that have been removed. They should know that they will be removed as Apple publishes those facts many years prior to removing the features.
An Upgrade takes you to a major, new version of software whereas and Update just makes changes to the same major version of the software.
Yosemite was an Upgrade, not an Update.

Verizon Fios and Airport not working. PLEASE HELP!

Ok, so I have been trying to get my Airport Extreme and Express to work with my new verizon fios service for about 5hours now. incrediably frustrating becasue with my old service provider it took about 5min.
Here is what i need to do.
extend the fios network using my airport extreme. I need to wirelessly print and use it in my office which is far away from the Verizon MI24WR router. cords are not an option. I need this to be wireless.
I also need to extend my network downstairs to my airport express in order to use itunes to wirelessly listen to music on my speakers.
I have tried other things described in message boards but I need both the extreme and express to be wirelessly connected to the verizon router. Is this possible and if so how! Please explain in the simplest of terms.
I am beyond frustrated! PLEASE HELP!

do you have printer driver v6.12, if not here's the link
http://www.epson.com/cgi-bin/Store/support/SupportLeopardDetails.jsp?BV_UseBVCoo kie=yes&oid=54861#stage1
did you contact epson? try them too..

Airport extreme setup. Airport express reset to factory settings. Light stays blinking amber. Utility won't recognize

AIrport extreme is setup. Airport express reset to factory settings. Light continues to blink amber. Utility will not recognize express to setup

Thanks. We understand that you want to use the Express to set up a separate wireless network with another modem, is that correct?
Unfortunately, we did not receive an answer to the questions that we asked above and have repeated again below regarding the AirPort Express and AirPort Utility. We asked these questions because not all versions of the AirPort Express are compatible with all versions of AirPort Utility.
What model of AirPort Express do you have? If you are not sure, please locate the model number on the side or bottom of the AirPort Express. It starts with an "A" followed by four numbers. It might be something like A1264 or A1392.
What version of AirPort Utility are you using? If you are not sure, please open AirPort Utility, click on the AirPort Utility menu in the upper left corner of the screen, and then click on About AirPort Utility.

Airport Extreme setup issue- Please help!

Similar Messages

Maybe you are looking for