Airport Extreme "Show Time Connected" Display

"SHOW TIME CONNECTED" problem
I have a relatively minor problem with my Airport Extreme. I have elected to have the “Show time connected” displayed in my menubar. For the last few months, and certainly since I upgraded to OS 10.7, the time connected display keeps resetting itself, sometimes actually back into negative time, showing as a negative time connected and gradually working its way up to zero. At other times it will seem to work accurately for a day or 2 and then reset itself back to 0.
This does not seem to affect my Airport Extreme function which does not disconnect or dysfunction. It seems that it is only the timer itself that keeps resetting itself. I know this is a minor issue but would be happy for any advice on how to correct it.
Thanks very much.

I ran OS 10.5 for 3 years with my Time Capsule and never saw a negative time. I recently updated to 10.6, but I don't think that that caused the problem, although I didn't check the apparent connected time on another computer.
"...only seems to affect a few users." is not a defense. Apple's job is to write software that always works, not that works mostly. I'm not sure that there would be a flood of reports. I think that most people don't turn this option on. It's an obscure setting (people ask where it is in other forum posts) and of little apparent value. I use it because it's the only reliable indicator that I am actually connected to the internet. I would not have upgraded the firmware on my TC except that the flashing yellow light (that I can't reset) made detecting other problems with the TC impossible.
I should also point out that on a recent trip I connected to a wi-fi router that does not support displaying the connected time. However, my computer continued to display the time that my TC had been connected when last it spoke to my computer. This does appear to be a 10.6 bug, as 10.5 never did this.

Similar Messages

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
Power off the AirPort by pulling the power cord
Wait a minute or two
Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
Release the reset button and allow a full minute for the AirPort to restart
Now try to configure the AirPort again. If you continue to see the same symptoms as before, the AirPort will need to be replaced.

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

Connecting to Airport Extreme w/ Time Capsule

How can I connect a MacBook Pro to an Airport Extreme w/ Time Capsule?
The computer does not have an ethernet connection.
I would like to perform the first backup to Time Capsule with the computer physically connect to the Airport Extreme.

You'll need Thunderbolt to Gigabit Ethernet Adapter - Apple Store (U.S.)

Make AirPort Extreme share internet connection with Time Capsule

Hello,
This is the situation: in one room there's an old Mac, the modem which delivers the internet and the AirPort Extreme which is connected to the modem.
In another room there's the Mac Pro, the Time Capsule which is connected to the Mac Pro with an ethernet cable and to a printer via USB.
I want the AirPort Extreme to wirelessly share it's internet connection with the Time Capsule so that the Time Capsule can share the printer with all three Macs (old Mac, Mac Pro and Macbook Pro), the Mac Pro can use the Time Capsule for Time Machine functionality and maybe the Macbook Pro too.
And just using the Time Capsule for internet.
How can I do this?
At the moment the AirPort Extreme is disconnected and the Time Capsule is used instead, but this way I can't share the printer...
Thanks!

Is that AirPort Extreme "flat" or dome-shaped? If it's flat (802.11n-capable), you should be able to configure the "main" router to "Allow this network to be extended" and the other to "Join a wireless network". If the Extreme is dome-shaped, then you need a more-complicated "WDS" arrangement. In either case it shouldn't matter much which router plays which role.
I'm not sure what you mean by "And just using the Time Capsule for internet."
Nathan-NL wrote:
At the moment the AirPort Extreme is disconnected and the Time Capsule is used instead, but this way I can't share the printer...
Is the printer connected to the USB port of the Time Capsule? Can you see the printer in the "Printer" panel of AirPort Utility? What happens when you try to use it from one of the Macs?

Airport Extreme won't connect with my cable modem (Time Warner)

OK, I'm tired of staring at a blinking amber light. I'm reaching out to anyone out there who's had this problem. I've got everything connected right, the software loaded, the connections set on my laptop (Macbok Pro). But still my Airport Extreme won't connect to the Internet. I've tried different cables, rebooting both my modem and my Airport. For the record, I've had a Mac IT guy from my advertising agency come by my house and make sure that everything's installed and hooked up right. But it still keeps saying that my IP address is invalid, even though I can connect (wired) using the modem.
I suspect I'll just have to take it to the Genius Bar or something. But anybody got any ideas? I really want to join the 'n' generation....
-neil

atotheb, Welcome to the discussion area!
Did you power off the cable modem when switching the Ethernet connection from laptop to AirPort Extreme base station (AEBS)? This is usually required.

My Airport Extreme and Time Capsule both cannot do not mount my Seagate USB external hard.

My Airport Extreme and Time Capsule both cannot do not mount my Seagate USB external hard.
I am running OS 10.7.5
Both the TC and AE are updated to 7.6.1
The Seagate drive in formatted: Journaled HFS+
I tried everything on Apple's Article: HT1331 and the basic reboots and restarts.
"Next"

It sounds like you may be confusing "mount" with "recognize".
Connect the drive to the USB port on the AirPort Extreme
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon, then click Edit
Click the Disks tab
Does the AirPort Extreme "recognize" your hard drive? If yes, it will be displayed in the window.
See example below of a WD 500 GB drive connected to the AirPort Extreme.
If your drive is formatted HFS+ and it does not appear here, then you will almost certainly need to use a powered USB hub with the hard drive.....even if the hard drive has its own power supply. The USB port on the AirPort Extreme and Time Capsule is under powered.
Post back when the drive is "recognized" and we will next "mount" the drive.....although you likely already know how to do this.

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.

Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

Have to reboot my airport extreme every time i restart my PC.

Hello,
Why is it that i have to reboot my Airport Extreme every time i restart my PC? I am able to connect to the network but not the internet, unless/until i restart my base station.
My phones and tablets are connected to the internet, so i know the my ISP is not the issue.

It is impossible to work this out without lots of details.
Like what PC OS do you run?
What connection, wireless or ethernet?
What you use test with the other if possible. Does it work for example swapping from wireless to ethernet??
I presume wireless as it is the most trouble prone.. When you start the PC does the wireless connect? Do you get IP by DHCP .. if so does it match what you get after a reboot.. look particularly at dns and gateway addresses.
Is the PC showing location as home or work/public.. it must be home to work properly.. also firewall might matter.
Also what type of wireless card is used.. poor windows drivers abound.. particularly Intel cards in laptops.
Is the wireless name SMB compliant.. ie short, no spaces and pure alphanumeric?
Is the wireless password mix of only case and numbers.. nothing non-alphanumeric?

Airport Extreme and Time Warner Roadrunner...

Hello,
I have never had so much trouble with my computer...
I currently have one PC, one iMac and a macbook pro. Both iMac and mbpro have been connected to airport extreme through wireless connection. PC is connected to extreme through ethernet. Yesterday, the Time Warner tech (actually third party company) showed up to switch me from Windstream DSL to Time Warner cable internet. Unforunately, I was not here. What he did was disconnect my extreme completely and connected PC to cable modem and left all Apple products off of internet. He said it was my responsibility to connect third party routers, etc.
I spent over four hours last night trying to successfully connect my extreme to the cable modem. No luck! Does anyone have a straight forward answer as to how this can happen?!? I can get it to where my airport is showing connected up to isp on imac, but it then fails with the internet. the ip address it shows is 169... When I check my ip address to the cable modem when directly hooked up through PC, it says it is 76...
At this point, I am totally lost and ready to just give up! Any help would be appreciated!!
Thanks!!

power down the network and the modem. connect modem to the extreme wan port. connect pc to ethernet lan port. power modem up first then the router. use Airport Utility to configure your network.

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network? I have an ISP provided wireless Router that has to remain as the base station. I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

My airport extreme will not connect to the Internet

My airport extreme will not connect to my toshiba router. I connected it to my office internet this morning but when I hooked it up at home it simply will not connect. I have tried resetting all the settings and have had no luck. It did work once upon a time. I currently have my airport express hooked up so I know there is connectivity.

I could never figure it out after trying everything I could and going to the genius bar I ended up just purchasing another extreme. The really funny thing is that I can set up a network between the two and it works fine. I am using it at work now with out any problems so I guess there is really no loss :-?

Issues with Airport Extreme and Time Machine

I have a Airport Extreme that is connected to a cable modem, that airport extreme is then hardwired connected to a time machine.
Recently, I have had trouble connecting wirelessly to the airport extreme. Even more troubling is that I can no longer can connect via ethernet to the time machine directly. In other words, the only way I can connect is by directly connecting to the airport extreme.
Any help would be great. Oh I have a MBP with the latest updates and a MB that is not connecting to the time machine or wireless to the extreme

angelop wrote:
I have used the following for about two years.
-MBP, Airport Extreme, External HD (1TB) for my time machine.
You probably know, that's "iffy" and +*not supported by Apple.+* See the Using Time Machine with a USB drive connected to an Airport Extreme *User Tip,* also at the top of this forum.
To get around this issue, I have switched off the Time Machine, and am only turning on once a week or so, to grab any changes or additions I've made. I've been doing this for about 6 months now with no problems.
Now whenever I do this, (It should only be backing up an album or two from iTunes,) it tries to back up my whole system again. EVERY TIME. It did not do this before.
If you go too long between backups, Time Machine will do a new, full backup. And once it decides to do that, it will keep trying until it succeeds. There are some other possibilities as well. See #D2 in the Using Time Machine with a USB drive connected to an Airport Extreme *User Tip,* also at the top of the +Time Machine+ forum.
If none of those seem to explain it, see #A1 there; download the TM Buddy widget, copy and post the messages here.
Why are you only backing-up once a week? Time Machine was designed to back up changes hourly, as long as your Mac is awake and the TC is in range. It will protect you best that way, and unless there's a problem, those backups will usually be very quick.
But if you're only going to back up once a week or so, then Time Machine is not the best app for you. See Kappy's post on Basic Backup, complete with links to the web sites of each product.

Cisco router RVS4000 with Airport extrem and Time capsule.

Problem droping connection to internet when is Time capsule in extended wifi mode. When I turn off wifi on time capsule Airport extreme work fine.
Airport extreme and Time capsule is conected via ETH.
Any idea ?
Thaks
B.

If you use ethernet to connect the AE and TC .. you must NOT extend wifi.. you use Create a wireless network. And setup with same name and security. You are using roaming network.. not extended wireless.. if you want to use extended wireless no ethernet
see http://support.apple.com/kb/HT4260

Airport Status Shows Minutes Connected

My airport status indicator is not only showing bars, it is showing minutes connected. As I am always connected, I find this incredibly annoying. It also takes up valuable menu bar space. If I click off "show airport status" the minutes go away, but so do the bars. I want the bars, but not the minutes. Can anyone help?

I apologize for my short response, especially since you're absolutely right - I could swear there was an option somewhere in Airport Admin Utility that shows time connected, but after posting my hasty response I can't find it either! So who's stupid now?
I realize you have 10.5. I only downloaded Airport Utility after reading your question. Airport Utility basically replaces 10.4.x's Airport Admin Utility I referenced. I haven't Airport Utitliy it yet but I'll post back when I find the equivalent function. It's gotta be there somewhere.

Airport Extreme "Show Time Connected" Display

Similar Messages

Maybe you are looking for