AirPort Extreme signal not strong enough

I have an AirPort Extreme. The signal is strong everywhere except in the kitchen, 15 meters but one story below...thick walls, concrete. Can I extend it using a simple Fritz Box (AVM Fritz wireless LAN 300E)?

Yes, follow the directions in KB 107454, AirPort Extreme and Express: Using WDS to create a network from multiple base stations.

Similar Messages

Airport extreme can not be recognized?, Airport extreme can not be recognized?, Airport extreme can not be recognized?

My Airport Extreme Station (4th Generation) is all of a sudden not recogized by the Airport Utility Software. I rebooted the Airport Extreme device a few times, disconnected it completely, and did it set it back to the factory default setting. No recognition. I tried configurating it with all my devices; IPhone 4S, IPad, MacBookPro and new iMac. Always the same message, even though I have internet access through the Airport default Wifi-ID. So the the Airport device works properly. Just no access for configuration, Does anyone has an advice to get back into the Airport Set-up through the Airport Utility program? Thank you.

Hello loving-truth,
I understand that your Airport Extreme is not being recognized in AirPort Utility, however you are able to access the internet via the Wi-Fi signal. We can give the steps in the following article a shot:
AirPort base station not seen or "An unexpected error occurred" appears in AirPort Utility 6.3
http://support.apple.com/kb/TS4597
Thanks,
Matt M.

Airport Extreme Signal Weaker than Before

My Airport Extreme signal is weaker than it used to be. Nothing has changed except I can no longer connect to the internet without running diagnostics each time I try to use it. It will connect and then stay connected until my macbook goes to sleep. When it wakes up, I have to re-connect using diagnostics.
I am using it in the same room I always have and never had problems before. But for the past several weeks, it is just not behaving as it always has. I have checked for a firmware update, but airport utility doesn't indicate that one is available. It's running: Version 6.3.2.
Any advice would be greatly appreciated. It's run great for the past several years. This is a new issue...

Because I can no longer connect to the internet without running diagnostics each time I try to use it. It will connect and then stay connected until my macbook goes to sleep. When it wakes up, I have to re-connect using diagnostics.
I am using it in the same room I always have and never had problems before. It will connect without problems in other rooms that are closer to the base station. But from the room where I ordinarily connect, it won't automatically connect anymore.
I can get it to connect from that room, and it will stay connected, but I can only do so by running diagnostics, telling it to assist me and then selecting the network and and following the steps to connect.

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... What am I doing wrong?

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... I have selected every possible security/password encryption level... What am I doing wrong? If it os possible where can I find step by step instructions? Please & Thank you!

The challenge with the older round AirPort Extremes are that they are "g" wireless devices.
When you configure them for WDS, the speed on the wireless network is cut in half...and probably will not have the bandwidth required to stream video reliably from either AirPort Extreme since both are affected by the WDS setup.
There is not an "automated" setup for WDS. You have to do this manually on both AirPort Extremes. Unfortunately, it is not an easy configuration and it's easy to make a mistake and hard to recover without starting all over again.
Apple's instructions for WDS are here if you want to give it a try.
http://support.apple.com/kb/HT4262
It is possible that it might work. Keep us posted on your progress
Adding a single AirPort Express will unfortunately not help. You have to have "n" wireless devices at all router points.

Connects to Airport extreme but not to internet

Whenever I close my laptop and reopen, I lose internet connection thru the airport extreme and I won't get it back. It seems that I will have connection to the Airport Extreme, but not the internet.
Sometimes what fixes it is turning the airport off and then on again (sometimes multiple times). Usually restarting the computer fixes it (but not always).
What happens is this (viewing Sysprefs/network/airport/network status and "internet connect"): the internet connect will report connecting...then will announce "connected", but show no "time elapsed" at the same time the Net status will read "airport is connected to ..network...with it's own IP address and may or may not be connected to the internet" And I won't be.
Then, when it starts working again (after the abovementioned turning off/on) it will start counting time elapsed, then in Net Status it will say "airport connected to ..network. you are connected to the internet via airport."
Also, whenever I use "internet connect" to turn the airport off, when I turn it back on again I will not have internet access, just the messages I list above. The "strenth meter" will say my signal is good (which it should be) and it says I am connected but doesn't show "elapsed time" nor will I have actual internet access.
Again, restarting the computer will usually work (less often, logging out then back in).
Another strange symptom-- When I hit the "disconnect" button under the airport section of "internet connect" it disconnects, then reconnects immediately. When I hit the disconnect button w/ in the Sysprefs/network/airport...etc, it does nothing but bring to the front window the "internet connect" window. So the only way to "disconnect" is to turn off the airport (which results in the above problem).
Side note--I am in the habit of turning off the airport (not the base, but from the computer) when I don't plan on using it for security-- am I being excessively paranoid? I do have my firewall in operation. Should I just leave it (being the airport) on all the time (in your humble opinion?
Sorry if this makes no sense or rambles, it is now 5:30 am and She Who Must Be Obeyed will be getting up in about an hour wanting to know if I fixed the computer yet. I'm tired.
Thank you in advance.
17" powerbook 1.5 PPc G4 Mac OS X (10.3.9)
17" powerbook 1.5 PPc G4 Mac OS X (10.3.9)

Try the following:
Delete Preferred Network(s)
- System Preferences > Network > AirPort > Configure
- In the "By default, join:" pull-down menu, select "Preferred networks"
- Delete the network(s) you regularly use from the list
Delete AirPort Keychain Entries
- Launch the "Keychain Access" application located in Applications/Utilties.
- Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
- Restart, or log out then back in.
Add Preferred Network(s)
- System Preferences > Network > AirPort > Configure
- In the "By default, join:" pull-down menu, select "Preferred networks"
- Add the preferred network(s) using the "+" button.
- Restart or log out then back in.

My airport extreme will not connect to the Internet

My airport extreme will not connect to my toshiba router. I connected it to my office internet this morning but when I hooked it up at home it simply will not connect. I have tried resetting all the settings and have had no luck. It did work once upon a time. I currently have my airport express hooked up so I know there is connectivity.

I could never figure it out after trying everything I could and going to the genius bar I ended up just purchasing another extreme. The really funny thing is that I can set up a network between the two and it works fine. I am using it at work now with out any problems so I guess there is really no loss :-?

The USB port on my 4th generation Airport Extreme does not recognize any peripheral devices whatsoever. In other words, it does not function at all. What can I do?

I have had my Airport Extreme for almost a year now. I have not been able to get it to work. It has never worked. I have tried everything in the apple manuals, my peripheral device manuals, and online help. My Airport Extreme Base Station has a completely dead USB port. The USB connector does have voltage and ground. Apparently there is no data transfer. I do not know how to test the data pinouts. I don't know if it is a software or driver problem, or if it is a hardware or wiring problem. My computer is a mid-2009 13" MacBook Pro. All of my external devices work well with the MacBook Pro. The USB functionality on the MacBook Pro has always performed without a glitch. It seems the problem with the Airport Extreme must either be a network communication problem or a hardware/hardwire problem. I bought the Airport Extreme to build a home inTRAnet network. I have a seperate 3rd party router for inTERnet. Contrary to what the manuals declare, the initial setup of my Airport Extreme requires inTERnet setup during the process. Even when the choice is made to limit the network access to LAN only, when I reach the end of the setup process, a prompts reads that the Airport Extreme may not function because I have not set it up for inTERnet with the WAN. Well, Dah... during the intial stages of the setup I told the machine to configure an inTRAnet only LAN setup. So... I went ahead and set it up for inTERnet and WAN. Either way, the USB port is not working. Then I set it up for the whole package, WAN, LAN, and everything. Still... no function out of the USB port. Any ideas?
P.S. The Ethernet works and so does the 802.11 tranceiver. The USB port is the only problem, but a major, major one for my needs. There is no peripheral functionality.

Okay so I figured it out. I inherited the Configurator already set up so I didn't realize that our former administrator was brilliant and set things up a little differently. To anyone else who finds themselves in this spot try this:
After you plug the iPad in and open Configurator instead of trying to 'Prepare' the device click 'Assign'
There should be groups of Users listed on the left hand side of the screen.
Select the group you want the ipad to be a part of, or make a new group. ***Note a group can be one person so this is a good feature for teachers to have individual app assignements for students.
After you select the user group click the little plus ( + ) button on the bottom of the screen under the second column of info where names and device serial numbers should appear.
Type the name of the person, group, whatever you want to identify that assignment by into the blank that pops up after you hit the plus ( + )
Then select the assignment you just made and tohe 'Check Our' button at the bottom. At this point a box will pop up with a window at the top listing all devices supervised by Configurator. There is a tiny down arrow button that opens a scroll down menu to the right of this box. Click that, then select the device connected by USB as the one to assign.
The name of the assignment you gave it will show on the lock screen now and you can assign apps and profiles to the device like you would any other device in your Configurator inventory.
Good Luck.

Set the Airport Extreme to not broadcast the SSID

Set the Airport Extreme to not broadcast the SSID

"Hiding" the SSID will do nothing to protect you from hackers.....and anyone else who wants to see your network, since there a numerous free utilities on the Internet that will reveal your network in seconds.
On the other hand, it might keep a few honest neighbors from seeing the name of your wireless network.
iOS devices often have trouble connecting to a "hidden" network, so you may need to display the network if your iPhone, iPad, etc have trouble connecting to the network.
Your call on this.
Assuming that you have Lion, Mountain Lion or Mavericks on your MacBook Pro.....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon, then click Edit in the smaller window
Click the Wireless tab at the top of the next window
Click Wireless Options at the bottom of the window
Enter a check mark in the box next to Create Hidden Network
Click Save, then click Update and allow a full minute for the AirPort Extreme to restart

Internet connection is through airport extreme is not connected

internet connection through airport extreme is not connected maybe there is a problem setting it up

Is it possible that using a Netgear Router connected
to the AE (which is also a router if I understand
correctly) could cause connection problems ?
Yes.
Ensure that that the AEBS is configured to not distribute IP addresses.
Also ensure that the AEBS is on a different channel to the DG834G.
iFelix

My new AirPort Extreme will not turn on anymore, no lights when plugged in.

My new AirPort Extreme will not turn on anymore, no lights when plugged in. I just bought it a few days ago. It has been working fine. I left the house for most the day and when returning home it would turn back on. I have tried to plug it into other outlets...nothing, I've tried the reset button...Nothing.

That is reported here a few times.. just take it straight back to apple or place of purchase for immediate exchange.

Airport Extreme will not show USB drive installed Solved!

Airport Extreme will not show USB drive installed Solved... At least for me!
Here's what I had to do to make it work with the newest 7.3.1 firmware.
Ready for this? No Joke Really!
1. Connect your USB drive to the Airport Extreme.
2. Turn it on.
3. Open the Airport Utility.
4. Go to Manual Setup.
5. Choose Disks and File Sharing.
Yep, we are going to set file sharing before we even see the disk we want to share!
You (I) had to set File Sharing on and Share Disks over Ethernet checked as well as set the Work Group (In my case). THEN restart the Airport Extreme.
After it re-started... My USB Drive was now present and ready for use.
I also dis-allowed Guest access. I re-started ALL computers in my network, both Windows and MAC. The USB drive held and works GREAT!
I know... Most of you thought this was a joke, It's not!
I tried everything to get the USB drive to work and failed every time just like most other people. Doing it this way worked like a charm.
Go Figure huh!
Hope this helps someone with this issue.
Message was edited by: DonaldH

How was the usb hard drive formatted? Was it NTFS, FAT32, or HFS+?

Can I turn my airport extreme when not in use?

can I turn my airport extreme when not in use?

Why?
The power saving will be negligible, and it may take time to re-establish a connection to your ISP's Network.

Airport loses my network, but not airport extreme signal

Since upgrading to leopard (10.5.1), my wireless network of computers (I am using an imac & mac pro book and a new airport extreme 802.11n base - all of which have worked without problems since networking them 6 months ago), will sometimes not show my own network as a network option in the airport status indicator in the menu bar (this happens sporadically with no apparent regularity). I have 4 bars of airport signal reception and I can even see the networks available around me, but mine will not be there. Usually it will pick it back up if I turn airport off and then reopen it but sometimes I have to restart the whole computer. This doesn't seem to be systemic in that one computer may lose the network while the other is working fine....any ideas. I have seen a lot of postings about wonky airport performance with the new leopard OS, but I couldn't find an answer to this.

Hi, (Sorry this is the first time I've posted on a forum)
I had a similar problem. I had successfully set up a network with 2 window computers, running XP and Vista,and an airport extreme. Works great so long as I don't upgrade the firmware on the basestation to 7.2.1.
Recently I saw the light and purchased an Imac with Leopard and Bootcamp. Couldn't connect to my network. Did recommended changes like turning off IPv6 in the imac's airport utility, and changed the basestation IPv6 mode to local link only. Tried to manually setup DNS server address etc on th imac. Went thru the usual stuff with the Apple helpline. No luck.
Found the only way to connect to the network was to switch off the basestation, get the network diagnostic on the imac to start searching for any networks, then switch back on the basestation. Worked.
Then I read on the forum about trying different radio channels on the basestation, rather than leaving it on the default setting "automatic". I tried Channel 11 and (I guesss it it Xmas!) it works perfectly.
Hope this is of help.

Airport Extreme will not secure wi-fi signal

I just had my AT&T DSL service activated, and I am trying to secure the wi-fi network using Airport Utility 6.2. My Airport Extreme is broadcasting the unsecured signal but I am completely unable to secure it.
Modem and router are hooked up correctly. I have to configure the base station for the unsecured signal to begin broadcasting. If I cancel the configure, the signal goes away completely.
So I configure the base station again, and I'm presented with a screen that reads "This Airport Extreme will create a network" and am presented with four fields: Network Name, Base Station Name, Password and Verify.
I enter a password and verify it, and am then given a screen to "Provide my PPPoE information I received from my ISP." I do that, and it spins for about a minute and says I am connected to the network I created. Except there is no wifi signal and no connection.
It has been like this for four days now. I am at my wit's end. ATT insists that the problem is not on their end. Any help anyone can give is appreciated. Thanks.

So to be clear - you have a DSL modem from AT&T, and want your Airport Extreme to broadcast this signal as well as route it?
You say you hooked up the modem and router correctly, are you able to get connection when plugging into the LAN port on the Airport Extreme?

My pc does not recognize my airport extreme signal

I have a AP extreme hooked to my DSL. I then send the signal to another AP extreme. Everthing has been working forn for over 1 year. We had a lightning storm I thought my base station was shot becuase my PCs would not hook to the network. MY mac book still worked. I purchased a new extreme and still My PC's will nt find the extreme signal. What am I doing wrong.
Rawhidetim

If the MacBook works and by changing out the base station, it still works, it sounds like the only thing that you didn't check was the PC itself to see if it may have sustained any damage during the lightning storm.

AirPort Extreme signal not strong enough

Similar Messages

Maybe you are looking for