Airport extreme with wifi internet

Friends, I`ve just bought the airport extreme. I have 2 macs (imac G5 e Macbook pro). My current internet is through a wifi system in my condominium. I therefore, don`t use ethernet cables (modem cable) for my internet. I already use wifi to connect to the internet.
My idea with the airport extreme was to connect my external HD and Printer to it and share with my two computer (as well as the files from the 2 computers). Indeed a personal wireless network.
I could connect the imac to the airport extreme and it recognized well. The problem is with since my internet is not through cables (currently wifi), I got the airport printer and HD but not the internet. How can I solve this and have the airport connections (printer and HD) and my wifi internet (another network)? Can I put 2 network together? thanks. Marcelo

Marcelo, I believe you should look into a wireless access point (WAP) to connect to your condo's wireless internet network. Then use a network cable to plug one of the WAP's network ports into the WAN port of the Airport Extreme. This way you can create a separate wireless network with the Airport Extreme for your computers/HD/printers and the Airport Extreme will route packets destined to the internet out the WAN port which is connected via a cable to the WAP to your condo's wireless network.

Similar Messages

  • Wifi connection AirPort Extreme with IP-camera

    I can't establish wifi connection Airport Extreme with IP-camera. At the same time cable connection is fine, but wifi not.
    Please, give me an advise.

    You need to create a wireless network on the AirPort Extreme, and then you probably will want to assign a compatible static LAN IP address to the camera so that you can port-forward from the router to the camera.

  • Configure an older airport extreme with an ipad1

    I'm a complete noob regarding wireless. I bought an ipad1 and an older aiport extreme (the white round one) off of ebay and am not sure how to get it all up and running. My Mac Pro does not have a wifi card so I can't use that. I plan to connect the airport to my router via ethernet. I've read that you can't configure an airport extreme with the ipad. What do I need to do to set up the extreme so the ipad can see and use it?
    thanks

    If the extreme is already configured, can I edit it using the app?
    Sure, if AirPort Utility recognizes the AirPort Extreme. Otherwise, you have to perform a Factory Default Reset on the Extreme and start over from scratch
    Open AirPort Utility, select the Extreme, and click Manual Setup
    Click the Wireless tab below the row of icons to get to the wireless settings.
    You want Wireless Mode set to "'Create a wireless network"
    Wireless Network Name is your choice
    Radio Mode = Automatic or 802.11b/g
    Channel =Automatic
    Wireless Security = WPA/WPA2 Personal
    Password = Your choice
    Confirm Password
    Click the Internet icon
    Click the Internet Connection tab
    Connect Using = Ethernet
    Connection Sharing = Off (Bridge Mode)
    Update to save settings.

  • How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

    How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
    When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro.  What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
    WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
    NOTE:  If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
    Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did.  He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
    Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse. 
    THIS IS WHAT YOU WILL NEED TO DO:
    First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
    down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up.  If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it.  Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

    I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
    I have a Linksys WRT320N I used for the initial Charter setup.
    I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
    Hasn't caused any issues so far but one thing I did notice.
    On the Linksys there were 3 DNS servers listed.
    The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
    I tried everything above, but light on modem still flashes yellow.
    I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
    I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

  • AirPort Extreme with 3T time capsule file security question

    Right now I am using a MacMini with an external HD as a file server.  I'm thinking g of using the new AirPort Extreme with 3T time capsule to do the same tho g (while also extended my wifi reach).
    With the Mac mini I have fine control over who gets to see and do what to which folders and files.  It seems that with the AirPort Extreme thee is no notion of permissions or access control -- if you can get on the wireless you can access the files.  That is extremely insecure. 
    Is my understanding correct?  Is there no way to secure files hosted on an AirPort Extreme so only certain users can access them??
    - john

    Are there any instructions for how to format and set HFS+ user permissions on the AP Extreme's HDD?
    For the formatting part, you will need to temporarily connect the drive to your Mac, and then, use the Disk Utility (a part of the OS X operating system) to partition and format the drive. You should find this utility in the \Applications\Utilities folder. For HFS+, choose "Mac OS Extended (Journaled)" for the Format option.
    For assigning user permissions using accounts, you will need to use the AirPort Utility.
    Run the AirPort Utility
    Select the Extreme, and then, click on Edit.
    Select the Disks tab.
    Select the HDD in the Partitions window.
    Choose "With accounts" as the Secure Shared Disks option.
    Click on the "+" button to add user accounts.
    For each account desired, enter the Account Name, Password, and File Sharing Access type.
    Click Save.
    Click Update to write the new configuration information to the base station and wait for the station to restart.

  • Which to buy?  Time capsule or Airport Extreme with USB drive(s)?

    I'm getting either a TC or an Airport Extreme with an external drive.
    Archive:
    I noticed that TC can archive to an external drive. It seems this can be handy for creating off-site backups. Can I do this with a drive on Airport Extreme (with a powered hub and another drive)? Or do I need to move the drive to a Mac and copy there? Or should I use a network backup instead in either case? I guess this is my main question: Can archive work with Airport Extreme?
    Mounting:
    Is mounting the Airport Extreme for WiFi range any easier than the TC?
    Drive failure:
    Is the TC drive likely to fail over the next couple years? And the other way, if the TC breaks, is the drive something I can use elsewhere? I'm a little concerned about having all my eggs in one basket.
    Other:
    Anything I should be aware of in making this decision?

    +Are there any constraints in the orientation of TC that the AirPort Extreme does not have?+
    No, not really as long as you give either device plenty of airspace as they both tend to run warm to very warm. I thought mounting the AirPort Extreme might improve the signal strength a bit, but it made no measurable difference for me.
    +Is the TC significantly heavier?+
    The Extreme is under 2 pounds, the TC comes in a bit over 3 pounds.
    +Is mounting on a pegboard bad for the HD?+
    I think you may be asking if you can mount it vertically. That's not a problem and the Apple store even sells wall mounts for either device.
    +Yikes. I got bad info. I read the "unsupported" constraint was dropped a couple versions ago. I thought all the comments on this were referring to the older versions of AirPort Extreme.+
    Here's the Apple document. Nothing changed with Snow Leopard and I saw a specific Snow Leopard document about this...just can't find it at the moment. I'm sure other forum regulars will confirm as well if they see this post.
    http://support.apple.com/kb/HT2038
    +Is there a list of file servers that Time Machine is compatible with?+
    Sorry, I don't have first hand knowledge on that and my policy is to only offer advice on things that I've done myself. That question might be worth a separate post since few people will see this question buried where it is.
    Message was edited by: Bob Timmons

  • What is the best way to hookup my airport extreme with my time capsule ?

    what is the best way to hookup my airport extreme with my time capsule ?

    It sounds like you have the AirPort Extreme configured as the "main" router on your network.
    If that is the case, connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the Time Capsule
    Power up the Time Capsule
    Connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule
    Open Macintosh HD > Applications  > Utilities > AirPort Utility
    Click on the Time Capsule, then click Manual Setup
    Click the Wireless tab below the row of icons and make sure that the setting for Wireless Mode = Off
    Click the Internet icon, the click the Internet tab
    Insure that the setting for Connect Using = Ethernet
    Insure that the setting for Connection Sharing = Off (Bridge Mode)
    Click the Update button at the lower right of the window and wait a full minute for the Time Capsule to restart
    Then power cycle the entire network by powering everything off....order of power down does not matter
    Wait a minute
    Power up the modem first, and let it run a few minutes by itself
    Power up the AirPort Extreme next and let it run a full minute
    Power up the Time Capsule next and let it run a full minute
    Keep starting devices one at a time about a minute apart until the entire network is back up
    You will need to reset the backup path from your Mac to the Time Capsule to get backups going again
    Open System Preference (gear icon on the dock)
    Open Time Machine
    Click Select Disk
    Click the Time Capsule to highlight it
    Click Use for Backups or Use Disk and backups should begin again in a few minutes
    If you do not want to leave the Mac connected to the Time Capsule by Ethernet, remove the Ethernet cable from the Mac to the Time Capsule, then log on to the AirPort Extreme wireless network

  • HT4356 I have an HP 4500 printer connected to airport extreme with usb.  All our portable notebooks print via air but cannot get iPad to be recognized for printing.  Do I really have to have one of the other HPs listed?

    I have an HP 4500 printer connected to airport extreme with usb.  All our portable notebooks print via air but cannot get iPad to be recognized for printing.  Do I really have to have one of the other HPs listed?

    Rufus Cat-
    Even if it was compatible, AirPrint does not work through a USB link, only Ethernet or WiFi.
    I do not see your HP 4500 listed on Apple's list of AirPrint compatible printers.  <iOS: AirPrint 101>  Therefore you need to take another approach.  To start, I suggest you download the free HP App, ePrint Home & Biz.  It has limitations, but should get you printing with your existing setup.
    There are other printing Apps with more features such as Print n Share and PrintCentral, but they can only be accessed from within other Apps that have the "Open In" option.
    Your best option may be to share your computer's printer as AirPrint over WiFi.  Programs that are reported to do that well are Printopia and FingerPrint.  Your computer must be on and awake any time you want to print.  <Printopia for Macintosh>  <FingerPrint for PC and Mac>
    Fred

  • Do I need to connect the AirPort Extreme with a ethnet cable

    Do I need to connect the AirPort Extreme with a ethnet cable

    Hi Tracy,
    I have an airport express connected by ethernet cable to a Netgear modem which is connected to a phone socket. Those devices stay at one end of the house. I can use my MacBook Pro to connect to the internet (by Wi-Fi, no cables) anywhere else in the house.  I hope this helps.
    Ian.

  • Airport Extreme with 6 TB Drive vs. Drobo vs. NAS?

    I am looking for system design advice in preparation for a new Mac Pro set up.
    Long story short- I am a semi-professional photographer.  I shoot 1 - 2 TB a year (Nikon D800 and various other bodies).  I currently have a 24" iMac (2007) and a MacBook Pro (2008) that are WELL past their prime.  I have at least 8 TB of external drives with all of my previous years of Aperture libraries connected to my iMac which is my primary machine.
    My question-
    I am looking to have my previous Aperture libraries accessible to all of my machines and have a central storage solution. 
    I am looking opinions on placing a new Airport Extreme with a 6 TB external drive connected to it with my previous libraries (which do not change) on it and have it Time Machine backup my current photo library and system nightly.  I do not require fast access to my previous libraries or fast backups.
    I have off site backups of all my libraries and I backup my current stuff monthly offsite.
    My new MacPro set-up will likely have a 4-6 TB G Tech drive attached to it for fast access for video projects etc.
    I want all my photos accessibl, a current onsite backup… and I want it all automated- no input at all… and I don’t want a big huge mess of RAID drives and worries of multiples drives all over the place.
    What would most of you suggest?
    Drobo? NAS? … any help is appreciated.
    Thanx

    Thank you for the replies. 
    My predicament can’t be unique. I need a large chunk of connected, stable and slow storage that seldom gets used but is safe and sound… and I need a safe automatic backup of my current projects (but never am I so stressed that every nanosecond of data is replicated on the moon at the speed of light…).
    I have witnessed massive Drobo failures and oddly been thankful that I had a mess of several external drives on my desk.
    The other challenge is that my new system will be installed in a location that has no easy way of connecting to the wired network in my house…
    Should I go with an Airport Extreme to increase the wifi speed a bit in the house and an attached Drobo 5D to the new machine?

  • How to set up airport extreme with TPG ADSL2 ?

    How to set up airport extreme with TPG ADSL2 ?

    I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
    I have a Linksys WRT320N I used for the initial Charter setup.
    I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
    Hasn't caused any issues so far but one thing I did notice.
    On the Linksys there were 3 DNS servers listed.
    The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
    I tried everything above, but light on modem still flashes yellow.
    I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
    I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

  • AirPort Extreme with USB hard drive

    Hi...I have an AirPort Extreme with a Maxtor OneTouch 250MB hard drive attached (via USB port). I have two computers which access the internet and the hard drive through the AirPort.
    The first computer is a 1.8 GHz PowerPC G5 (with 3GB of SDRAM). The second is a 2 GHz Intel Core2 Duo IMac (with 4GB of SDRAM).
    Both computers have full signal strength via AirPort and both computers have no connection/speed issues with the internet. It's when trying to copy to/from the USB disk that there are problems. The older Mac, the G5, has no problems at all. Great copy speeds in both directions, I can even work off of files on the USB disk without a problem.
    The iMac, though, has a problem writing to/from the external hard disk. It connects without a problem, but after that, things come to a standstill.
    For example, I can copy a 25MB file from the AirDisk to the G5 in about 15 seconds. If I try to copy the same file to the iMac, it takes as long as 5 minutes. I've tried every setting I can in AirPort Utility, including trying each of the channels individually, and nothing helps. I've disconnected the G5 from the network and that didn't make a difference, either.
    Other info...the AirPort firmware is updated to version 7.3.2 and both Macs are updated to System 10.5.4.
    If anybody has any advice, I will be eternally grateful.

    I have a very similar problem. I have a 2.8 GHz iMac with 2GB RAM and am using OS X v10.5.4, and an Airport Extreme (v7.3.2), both updated to latest firmware. I have a 500 GB TrekStor external HD connected to the AEBS via USB. The TrekStor HD was pre-formatted in FAT32 and is visible on my iMac's desktop and in Finder but I cannot transfer files to it or see files on it. When I drag and drop a file on the TrekStor, it sometimes seems to go well but then the file is not visible via Finder, and sometimes I get an "insufficient privileges" message. I repair permissions on the iMac's internal HD without any change. I am logged in as the admin. All assistance is much appreciated!

  • How do I connect my airport extreme to wifi as a repeater

    how do I connect my airport extreme to wifi as a repeater?

    Thanks for the info.
    Unfortunately, Apple has designed their routers to only extend or repeat the wireless signal from other Apple routers.
    It would be extremely unlikely that the AirPort Extreme would be able to extend or repeat a wireless signal from another manufacturer's router.
    I suppose that it could not hurt to try, but if the Extreme is still unopened, it might be a better idea to return the Extreme, get the information about the router at the neighbor's and then use a product from the same manufacurer that would be compatible to repeat or extend the wireless.

  • How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

    How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?  I have an ISP provided wireless Router that has to remain as the base station.  I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

    One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

  • I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. C

    I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. Suddenly, the "timeout" is not allowing me to connect to my wireless network.

    It could be that there's a new source of interference.
    Use the advice in the second message of this thread to investigate the signal and noise levels that each client sees:
    http://discussions.apple.com/thread.jspa?threadID=2347845&start=1
    By the way, you've been misled by the poor field labeling into trying to type your entire message into the subject field, instead of putting a one-line topic description there.

Maybe you are looking for