Airport Extreme with wired web server Problems

I am setting up a wireless network with a new Airport Extreme. When I hook it up per the instructions my hard wired web server and PC don't work. My laptops work fine. I put a static IP address on each computer via network prefs. I tried to take the AirPort ethernet out port and use both the cross over and a regular ethernet to the switch then to a wired PC and Mac server. But it will not work.
Connection that does NOT work: DSL modem - ethernet cable - AP Extreme WAN port - ethernet cable out - web server (live video) & PC
If I go back to the way it was set before the AP it works fine. (see below) Wouldn't the network be quicker wired from the modem to the AP Wan port? My IP said I shouldn't need to use crossover ethernet cable.
Connection that works: DSL modem - cross over ethernet - network switch - ethernet to AP Extreme - ethernet to web server - ethernet to PC
Thanks for your assistance.

I suggest that you don't try to configure the wireless print server until you have the AEBSn network with USB disk sharing working correctly.
My expereince with AEBSn disk sharing so far is that it's best to use accounts to secure shared disks. If you can't get the network file sharing to work right off, try this:
My Network Places>Add a network place>Add Network Place Wizard>Next>Choose another network location>Next>type the following string as the network address and proceed to complete the wizard:
\\[LAN IP address of AEBSn]\[name of shared disk]
Example: \\192.168.1.1\MemphisBelleServer
If you are using accounts to secure the shared disk, type in the User name and Password when the Connect to dialog box appears. I have had trouble using (and no longer use) disk passwords, so I don't know whether that method works the same way with respect to the Connect to dialog box.

Similar Messages

Problem with iPlanet Web Server 6

We are getting an intermittent problem with our web server, the users start to get problems connecting to the web site.
I have found the following message in the error log -
failure ( 2390): Error accepting connection -5928, oserr=130 (Connect aborted)
can anybody help???

Check out the below.
Problem 4680491. CSS causes oserr=130 in iWS 6.0 logs.
Workaround
If you are using the Cisco Content Services Switch (CSS) with Sun ONE Web Server and have set the value of the sticky bit setting in CSS to on, the following error is logged periodically in the error logs:
failure ( 2210): Error accepting connection -5928, oserr=130 (Connect aborted)
This is caused not by a defect in Sun ONE Web Server but by the setting of the sticky bit in CSS. To avoid the error logging, set the value of the sticky bit in CSS to off.
Which as been fixed in iWS 6.0 SP5.
For more info check the below link.
http://docs.sun.com/source/816-6434-10/rn60sp5.html
Dakshin.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How to install utility or manage Airport extreme base from Win server 2003

I hope that everybody is doing well.
I am currently studying Server Administration and Maintenance. I am running Win server 2003 and soon to use Win server 2008, provided by the school several months ago. I am trying to install the utility for my airport extreme base in the server that I have at home to no avail. I will appreciated if somebody can help me. My options are limited I cannot buy another wireless router and I really need to do this for my studies. My server does connect to the base by the Ethernet but not I cannot manage the router in the server a major problem in the class that starts today. I will really appreciate if somebody can help to solve this issue which may be the other viable option because I cannot buy another computer I truly hope there is another option that does not include having to purchase another router I love my airport extreme base ;-D

In finder, go to - Mac HD, Library, Preferences - drag the folder 'SystemConfiguration' into the trash
Restart.
Evidently, there were some corrupt files in there which, in my case, made my AP utility sporadically lose both my airport devices. Trashing that folder and the files within, and restarting automatically creates a new fresh system configurations folder. The AP Utility immediately found my hardware with this fix, but only time will tell if this was root cause and be a long-term fix.
Best of luck.

AirPort Extreme with 3T time capsule file security question

Right now I am using a MacMini with an external HD as a file server. I'm thinking g of using the new AirPort Extreme with 3T time capsule to do the same tho g (while also extended my wifi reach).
With the Mac mini I have fine control over who gets to see and do what to which folders and files. It seems that with the AirPort Extreme thee is no notion of permissions or access control -- if you can get on the wireless you can access the files. That is extremely insecure.
Is my understanding correct? Is there no way to secure files hosted on an AirPort Extreme so only certain users can access them??
- john

Are there any instructions for how to format and set HFS+ user permissions on the AP Extreme's HDD?
For the formatting part, you will need to temporarily connect the drive to your Mac, and then, use the Disk Utility (a part of the OS X operating system) to partition and format the drive. You should find this utility in the \Applications\Utilities folder. For HFS+, choose "Mac OS Extended (Journaled)" for the Format option.
For assigning user permissions using accounts, you will need to use the AirPort Utility.
Run the AirPort Utility
Select the Extreme, and then, click on Edit.
Select the Disks tab.
Select the HDD in the Partitions window.
Choose "With accounts" as the Secure Shared Disks option.
Click on the "+" button to add user accounts.
For each account desired, enter the Account Name, Password, and File Sharing Access type.
Click Save.
Click Update to write the new configuration information to the base station and wait for the station to restart.

Which to buy? Time capsule or Airport Extreme with USB drive(s)?

I'm getting either a TC or an Airport Extreme with an external drive.
Archive:
I noticed that TC can archive to an external drive. It seems this can be handy for creating off-site backups. Can I do this with a drive on Airport Extreme (with a powered hub and another drive)? Or do I need to move the drive to a Mac and copy there? Or should I use a network backup instead in either case? I guess this is my main question: Can archive work with Airport Extreme?
Mounting:
Is mounting the Airport Extreme for WiFi range any easier than the TC?
Drive failure:
Is the TC drive likely to fail over the next couple years? And the other way, if the TC breaks, is the drive something I can use elsewhere? I'm a little concerned about having all my eggs in one basket.
Other:
Anything I should be aware of in making this decision?

+Are there any constraints in the orientation of TC that the AirPort Extreme does not have?+
No, not really as long as you give either device plenty of airspace as they both tend to run warm to very warm. I thought mounting the AirPort Extreme might improve the signal strength a bit, but it made no measurable difference for me.
+Is the TC significantly heavier?+
The Extreme is under 2 pounds, the TC comes in a bit over 3 pounds.
+Is mounting on a pegboard bad for the HD?+
I think you may be asking if you can mount it vertically. That's not a problem and the Apple store even sells wall mounts for either device.
+Yikes. I got bad info. I read the "unsupported" constraint was dropped a couple versions ago. I thought all the comments on this were referring to the older versions of AirPort Extreme.+
Here's the Apple document. Nothing changed with Snow Leopard and I saw a specific Snow Leopard document about this...just can't find it at the moment. I'm sure other forum regulars will confirm as well if they see this post.
http://support.apple.com/kb/HT2038
+Is there a list of file servers that Time Machine is compatible with?+
Sorry, I don't have first hand knowledge on that and my policy is to only offer advice on things that I've done myself. That question might be worth a separate post since few people will see this question buried where it is.
Message was edited by: Bob Timmons

I have an airport extreme with a USB printer attached (non-airprint). Can i print from my ipad?

I have an airport extreme with a USB printer attached, it is a non airprint printer.
I can print via my network from my desktop but I want to know if i can print from my ipad 2 and ipad 1

Printing from an iPad or iPhone
To print directly from an iPad you need an AirPrint - enabled printer on the same wireless network as the iPad. All AirPrint printers are wireless but not all wireless printers are AirPrint-enabled.
If you do not have an AirPrint printer, a number of workarounds exist that enable the use of any printer you normally use, even older ones that may predate AirPrint by decades. Search for the following products:
handyPrint (Mac only, donation-supported)
Printopia (Mac only, $19.95 with free trial)
These are utilities you install on the Mac you normally use for printing, enabling it to act as an AirPrint print server. The Mac must be "on" but may be asleep for them to work. The iPad needs nothing else, no iOS apps need to be installed and no configuration is necessary. If your computer can print, so can the iPad, using one of these utilities on your Mac.
Equivalent utilities may exist for PCs but I have no experience with them - I suggest https://www.collobos.com
You can also buy this standalone hardware print server, bypassing the need for a computer altogether:
http://www.lantronix.com/it-management/xprintserver/xprintserver.html
Otherwise you will need to buy an AirPrint printer or multifunction device.

Airport Extreme with 6 TB Drive vs. Drobo vs. NAS?

I am looking for system design advice in preparation for a new Mac Pro set up.
Long story short- I am a semi-professional photographer. I shoot 1 - 2 TB a year (Nikon D800 and various other bodies). I currently have a 24" iMac (2007) and a MacBook Pro (2008) that are WELL past their prime. I have at least 8 TB of external drives with all of my previous years of Aperture libraries connected to my iMac which is my primary machine.
My question-
I am looking to have my previous Aperture libraries accessible to all of my machines and have a central storage solution.
I am looking opinions on placing a new Airport Extreme with a 6 TB external drive connected to it with my previous libraries (which do not change) on it and have it Time Machine backup my current photo library and system nightly. I do not require fast access to my previous libraries or fast backups.
I have off site backups of all my libraries and I backup my current stuff monthly offsite.
My new MacPro set-up will likely have a 4-6 TB G Tech drive attached to it for fast access for video projects etc.
I want all my photos accessibl, a current onsite backup… and I want it all automated- no input at all… and I don’t want a big huge mess of RAID drives and worries of multiples drives all over the place.
What would most of you suggest?
Drobo? NAS? … any help is appreciated.
Thanx

Thank you for the replies.
My predicament can’t be unique. I need a large chunk of connected, stable and slow storage that seldom gets used but is safe and sound… and I need a safe automatic backup of my current projects (but never am I so stressed that every nanosecond of data is replicated on the moon at the speed of light…).
I have witnessed massive Drobo failures and oddly been thankful that I had a mess of several external drives on my desk.
The other challenge is that my new system will be installed in a location that has no easy way of connecting to the wired network in my house…
Should I go with an Airport Extreme to increase the wifi speed a bit in the house and an attached Drobo 5D to the new machine?

Having trouble using my airport extreme as a media server for my ps3--can anyone help?

I'd like to set up my apple airport extreme with a USB seagate drive, and use the drive as a media server for my ps3. I have successfully connected my seagate drive to my airport extreme. I have successfully transferred a sample movie to this seagate drive. My laptop is easily able to find the drive and is able to play the sample film from the drive. How can I turn this drive into a media server? I'd like for my PS3 to be able to read movies off the network drive and play them. Help??

Welcome to the discussions, DanSwiggsD!
If you have a non-Apple device as your main router, unfortunately the AirPort Extreme has almost no chance of compatibility with your main router.
If you do have an Apple router as your main device, please post back with your model number and we'll let you know how your devices should be configured.
If you don't have an Apple device as your main router you have a few options to connect the xbox:
1) A pair of ethernet powerline adapters could be used if you did not want to run a regular ethernet cable from your main router to the xbox.
2) The new AirPort Express 802.11n model does have a feature called Proxy STA which should allow it to receive a wireless signal from any wireless router and allow the ethernet port to be enabled.
Message was edited by: Bob Timmons

Replacing older airport extreme with time capsule

I am thinking of replacing my airport extreme with time capsule. I had a lot of problems setting up airport extreme a few years ago - now it is very reliable. I don't want to have the same issues with time capsule. Can I simply physically replace the airport extreme with time capsule using the same settings as previously
Advice gratefully anticipated

Welcome to the discussion area, pancuronium!
You will use AirPort Utility on your Mac for this operation:
(Macintosh HD > Applications > Utilities > AirPort Utility)
Open AirPort Utility and click Manual Setup
Click the File menu at the upper left corner of the screen near the Apple icon
Click Export Configuration File
Assign a name to the file and save it to a convenient location like the desktop
When you are ready to install the Time Capsule....
Open AirPort Utility and click Manual Setup
Click the File Menu
Select Import Configuration File
Navigate to locate the file that you exported to import all the settings into a new configuration for the Time Capsule
Message was edited by: Bob Timmons

AirPort Extreme with USB hard drive

Hi...I have an AirPort Extreme with a Maxtor OneTouch 250MB hard drive attached (via USB port). I have two computers which access the internet and the hard drive through the AirPort.
The first computer is a 1.8 GHz PowerPC G5 (with 3GB of SDRAM). The second is a 2 GHz Intel Core2 Duo IMac (with 4GB of SDRAM).
Both computers have full signal strength via AirPort and both computers have no connection/speed issues with the internet. It's when trying to copy to/from the USB disk that there are problems. The older Mac, the G5, has no problems at all. Great copy speeds in both directions, I can even work off of files on the USB disk without a problem.
The iMac, though, has a problem writing to/from the external hard disk. It connects without a problem, but after that, things come to a standstill.
For example, I can copy a 25MB file from the AirDisk to the G5 in about 15 seconds. If I try to copy the same file to the iMac, it takes as long as 5 minutes. I've tried every setting I can in AirPort Utility, including trying each of the channels individually, and nothing helps. I've disconnected the G5 from the network and that didn't make a difference, either.
Other info...the AirPort firmware is updated to version 7.3.2 and both Macs are updated to System 10.5.4.
If anybody has any advice, I will be eternally grateful.

I have a very similar problem. I have a 2.8 GHz iMac with 2GB RAM and am using OS X v10.5.4, and an Airport Extreme (v7.3.2), both updated to latest firmware. I have a 500 GB TrekStor external HD connected to the AEBS via USB. The TrekStor HD was pre-formatted in FAT32 and is visible on my iMac's desktop and in Finder but I cannot transfer files to it or see files on it. When I drag and drop a file on the TrekStor, it sometimes seems to go well but then the file is not visible via Finder, and sometimes I get an "insufficient privileges" message. I repair permissions on the iMac's internal HD without any change. I am logged in as the admin. All assistance is much appreciated!

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network? I have an ISP provided wireless Router that has to remain as the base station. I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. C

I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. Suddenly, the "timeout" is not allowing me to connect to my wireless network.

It could be that there's a new source of interference.
Use the advice in the second message of this thread to investigate the signal and noise levels that each client sees:
http://discussions.apple.com/thread.jspa?threadID=2347845&start=1
By the way, you've been misled by the poor field labeling into trying to type your entire message into the subject field, instead of putting a one-line topic description there.

Integrating tomcat 5.0.28 with apache web server 2.2

hi all
i tried a lot on net but could not get the steps for
connctivity between tomcat 5.0.28 with apache web server 2.2.
any one pzl do help me in finding the solution
pzl do tel me the step by step process for this connectivity
sus

hi :-)
you need jk modules ;-)
i havent try the integrating the version of apache web
and tomcat you specify but you can refer to the links below :-)
gudluck :-)
http://www.serverwatch.com/tutorials/article.php/2203891
http://www.onjava.com/lpt/a/2826
http://raibledesigns.com/tomcat/
regards,

How to connect to dsl airport extreme with built in modem

Hello everybody,
while we were tiding our cellar, i found an old airport extreme (a1034) with a built in modem, but i aint able to connect to my isp.
I looked throug the manual, but i didnt got answers there (maybe because of my poor english) . Is there a tutorial out there which tells me
how to connect to my isp?
Regards Floh
PS: again sorry for my poor english

If you try to set up the new AirPort Extreme with AirPort Utility 5.6.1, you will receive a notice that you need a more up to date version of AirPort Utility.
Nevertheless, AP 5.6.1 will allow you to set up the basics....wireless network name, password, etc.
It will appear that you can change other settings that are not found in more recent versions of AirPort Utility, but if you go in and check using a newer version of AirPort Utility, you will find that the settings that you thought you had made have not "stuck".
For example, you want to change the Radio Mode on the new Extreme and not use the Automatic setting. AP 5.6.1 will appear to let you do this. But, if you check the setting using a more recent version of AirPort Utility you will see that the setting is still set at "Automatic".
So, the bottom line here is that unless the newer version of AirPort Utility has the specific setting that you want to change, you will not be able to make that change.
Is there ANY chance, to set up my new "towers" with more
options, than the current Airport Utilities do offer?
Unfortunately, no.

Airport Extreme with wired web server Problems

Similar Messages

Maybe you are looking for