Airport modem and itunes streamed same time

Is it possible to be online with my wireless connection through (via a Netgear router) and at the same time to stream Itunes to airport express? Currently, my mac G4 asks me to choose one or other of the connections.

You must configure the Express to be a client on the Netgear's wireless network. You can use the Airport Setup Assistant to accomplish this. Make sure you do not specify that you want to extend the range of the wireless network: the Netgear router is incapable of supporting that feature.

Similar Messages

Airport:PS3 and Mac at same time?

I'm looking at getting an airport express or extreme whichever will be enough for my needs. This is actually going to be my first router, here are what I'm looking for it to do for me:
rue
1) I am only getting this to be able to connect my PS3 to the Internet wirelessly, my computer doesn't need to be wireless at all.
2) I need to know if I can use both the PS3 and the iMac on the Internet at the same time?
3) and finally which of the airports is going to be good for me? The PS3 is about 25 ft away in the next room and I would prefer keeping my iMac connected to cable modem if that is possible, any help would be great thanks

1) I am only getting this to be able to connect my PS3 to the Internet wirelessly, my computer doesn't need to be wireless at all.
To support both wired and wireless clients, you will want the AirPort Extreme.
2) I need to know if I can use both the PS3 and the iMac on the Internet at the same time?
Yes, both can be used simultaneously with either AirPort.
3) and finally which of the airports is going to be good for me? The PS3 is about 25 ft away in the next room and I would prefer keeping my iMac connected to cable modem if that is possible, any help would be great thanks
You will need the AirPort Extreme. You would not be able to keep the iMac connected to the cable modem. Instead, you would connect the AirPort Extreme to the modem, and then, both the iMac and PS3 to the Extreme.

Airport express and itune streaming over distance

What is the distance in airport express can pass signal through audio out port? Can I connect an 75 foot stereo mini to rca connector cable to my stereo successfully? Thanks for anybodies help.

I'm not sure of the exact length restriction, but I have used a 100' cable with my AirPort Express Base Station (AX) to connect to the stereo and it worked just fine.

Using Airport Express and Intenet at same time

I have set up an Airport Express to play music from my Mac in another room. Works fine. But when I am doing that, I cannot use the internet on the Mac. This is because the wireless symbol on the title bar gives me two choices -- my wireless network or the Airport Express. Is this normal or is there something I can do to have both working at once. Ta in advance

the_gauntlett, Welcome to the discussion area!
You need to reconfigure the AirPort Express (AX) so that it joins a wireless network and select your current wireless network.

Is there a way I can stream video from my 2012 AirMac to the Apple TV using airplay and at the same time stream the audio to an air speaker?

Is there a way stream video from a 2012 MacBook Air to a TV using Apple TV and at the same time steam the audio to an air speaker. Also the same question but using an ipad

You can try one thing. Follow these steps:
1. On your Mac, turn on AirPlay Mirroring and connect it to the Apple TV, so audio and video will stream from the Apple TV.
2. Turn off the sound of the TV where you have connected the Apple TV.
3. Then, make sure that you have turned on the AirPlay speakers. Then, open System Preferences > Sound > Output, and choose the external speakers, so sound will stream from these external speakers.
This should work correctly

Is it possible to record and play at same time in swift, is there a option to record without storing the file

I am making a microphone, is it possible to record and play at same time in swift, is there a option to record without storing the file

Its pretty simple with FMS. You just need to do following things:
Publish using FMLE with following settings: (just telling which are needed , rest you configure based on your needs)
Video codec: H.264
Audio Codec: <of your choice>
Server ip: rtmp://<server-uri>/<app-name>
Stream Name: mp4:<stream-name>.f4v
Application : Server-side code
application.onPublish = function(myclient,mystream){
     mystream.record();
application.onUnpublish = function(myclient,mystream){
     mystream.record(false);
Have a client , which subscribes in following live mode:-
ns.play("mp4:<stream-name>.f4v",-1,0,true);   // this is subscribing in live mode
In this way even if file is recorded, your clients are subscribing in live mode so all will be in sync.
Now if you want to disallow any clients who will try to subscribe to "recorded" file when live event is going on, you can achieve using auth adaptor. (let me know if you want to enforce such requirement)
But i think above solution solves your primary problem. Also please let me know if there are any issues in getting it work , i have given bare minimum which is required.

Ethernet Internet & Airport Express Printing at the same time

Ok Guys:
My 18 year old cousin is going off to University this fall, and she will be taking her iMac G5 and a new Macbook with her. She wants to set up her canon printer wirelessly by using an Airport Express. Assuming her Internet access is by ethernet, provided in each residence room by the university, can she also setup an Airport Express to use for wireless printing at the same time? In other words will the following scenario work?
Network 1: Ethernet Internet (provided by the University)
AND (at the same time)
Network 2 : Wireless printing network by Airport Export Express.
Thanks.
-Robert
--Please Include As Detailed System Info As You Can With Your Questions!-- Mac OS X (10.4.9) PM Quad 8.5GB 7800GT 30"; MBP 17 2.33 C2D 3GB My 1st Computer was an Apple IIc!

She can configure the AirPort Express (AX) with the option to distribute IP addresses DISABLED.
Then she can connect the AX directly to the Ethernet connection in the room.

Delete records in a table and at the same time print out for reference

I am working on a req to delete some records from a table and at the same time, record/print the deleted records in the outstream (DBMS_OUTPUT.PUT_LINE)
DECLARE
v_rec_po hst_po%ROWTYPE;
BEGIN
DELETE FROM hst_po po
WHERE abbrpoid = '&opportunity_code'
AND updatedby = (SELECT employeeid
FROM tes_employee
WHERE name = &emp_name)
AND audittimestamp BETWEEN TO_DATE ('&start_timestamp',
'DD-MON-YYYY HH24:MI'
AND TO_DATE ('&end_timestamp',
'DD-MON-YYYY HH24:MI'
END;
I was thinking of using returning into and then using DBMS_output to pull out the delted records, but there will be multiple rows deleted fro this statements. I am stuck here..Can anyone help

How about:
SQL> create table t
2 (x int)
3 /
Table created.
SQL> insert into t
2 select rownum
3    from all_objects
4   where rownum <= 10
5 /
10 rows created.
SQL> declare
2     cnt pls_integer;
3 begin
4     delete from t;
5     cnt := sql%rowcount;
6     dbms_output.put_line ('Removed: '||to_Char (cnt));
7 end;
8 /
Removed: 10
PL/SQL procedure successfully completed.Edited by: Alex Nuijten on Jun 4, 2009 8:58 AM

Recording Video and Audio at Same time with simultaneous sync

I want to record a keyboard performance into garageband and at the same time record the playing of that performance with my video camera. Then I want to create a movie using the music from garageband and the video from the camera. I was thinking that if I can sync the video and audio when I'm recording the session, then that part is taken care of. Or, maybe this is easier than I think it is?
Is there a way to do this so that I can use the garageband record performance and have it synced to the video on the camera?
I don't want to use the audio from the video camera because the performance that is captured in Garageband will be much better and I can do editing of the individual notes in GB.
In the end, I just want to make a movie and/or podcast of the performance.
I'm a newbie regarding this, but I did search the forums and couldn't find anything specific. Mostly it was about importing video into GB3 and then syncing new audio. I'll basically have audio and video from the same performance in two separate locations and I want to bring them together perfectly in Garageband.
Thanks for any help you can provide.
Powerbook G4 - DVI Mac OS X (10.4.9)

Okay. I got the video and audio all together. I told you I'd link to it when it was up.
http://www.youtube.com/watch?v=FxssYpUNJm8
There's also a copy of it at http://www.myspace.com/bonjimmy/
And as a quick side comment, even though I uploaded the same video to both YouTube and MySpace, the MySpace version is much better. YouTube must do something to the video after it's uploaded.
What I learned doing this project:
I recorded the video first (which gave me the sequencing of the piano performance) and then I dubbed the audio in later. However, there wasn't a good way to sync the video and the prerecorded piano, so there are some spots where the dubbed audio vocal isn't accurate to the video. I'm not sure what the pros do for this. I was hoping I'd remember how I sang for the video but when a couple weeks go by before re-doing the audio, it's about impossible. I tried, though.
I remember working with an old 4-track and smpte to a sequencer a long time ago. With the way it is now, it's pretty cool that you can record digitally and mix and match and everything falls together perfectly as long as you have a place to match the video and the audio. It's pretty cool.
What else???
Does anyone have suggestions that would have made it better? Also, if you have suggestions on my performance or whatever, I'd love comments, but you can do that on the linked page.
Thanks again for all your help. (The point of the video is because I'm thinking about getting back out there and doing some more playing... I'm looking for a band or something else interesting...)
Powerbook G4 - DVI Mac OS X (10.4.10)

How to collect form responses in adobe formscentral and at the same time receive form responses through email

My client wants to have the form that I created in FormsCentral to be able to collect email responses. So to do this, I downloaded the form as PDF then imported it into Acrobat. I created a button in Acrobat (this will be for the email response part). I used this script for that function:
// This is the form return email. It's hardcoded
// so that the form is always returned to the same address.
// Change address on your form to match the code below
var cToAddr = "[email protected]"
// First, get the client CC email address
var cCCAddr = this.getField("ClientEmail").value;
// Now get the beneficiary email only if it is filled out
var cBenAddr = this.getField("BennyEmail").value;
if(cBenAddr != "")
cCCAddr += ";" + cBenAddr;
// Set the subject and body text for the email message
var cSubLine = "Form X-1 returned from client"
var cBody = "Thank you for submitting your form.\n" + "Save the filled form attachment for your own records"
// Send the entire PDF as a file attachment on an email
this.mailDoc({bUI: true, cTo: cToAddr, cCc: cCCAddr, cSubject: cSubLine, cMsg: cBody});
I got it from here: http://acrobatusers.com/tutorials/dynamically-setting-submit-e-mail-address
I'm still kinda not sure how it works but I'm getting the idea. Now what I'm having trouble with is, how do I make it so that the user will be required to click on the scripted button and at the same time, also click on the FormsCentral's generated submit button? Because as I see it, the user can click on the scripted button but they can just close out the form without submitting it to FormsCentral.
Is there any way to make my idea work?
Any help is very much appreciated!
Thanks!

I do not know or have time right now to look up NDP format.
To write to NTFS from Mac, you need a driver.
And to write to HFS from Windows also.
I strongly recommend Paragon drivers for both.
That way you can access anything from any platform.
Paragon Software for Mac

How can I copy documents from a Sharepoint On Premises library to a Sharepoint Online library and at the same time preserving their metadata?

How can I copy documents from a Sharepoint On Premises library to a Sharepoint Online library and at the same time preserving their metadata?
I use the Open Explorer Windows to drag and drop the files, but the metadata are not copied. Thanks.

To maintain the metadata you'll need to use one of the third party tools that does this kind of migration. Metalogix has a product with a free trial that we have used before. (Don't remember whether the free version maintains metadata or not).
You can read about it here:
http://www.metalogix.com/Products/Content-Matrix.aspx
Paul Stork SharePoint Server MVP
Principal Architect: Blue Chip Consulting Group
Blog: http://dontpapanic.com/blog
Twitter: Follow @pstork
Please remember to mark your question as "answered" if this solves your problem.

Bluetooth seems like working since last week and at the same time I can't manage the Wi-Fi

Bluetooth seems like working since last week and at the same time I can't manage the Wi-Fi. I have already restored.

This entire thing is a hair over four months old, I don't think it should be acting up this much. Plus, this problem happens only once out of every 40 or 50 times I start this thing up. It's very infrequent, but it's there, and it just bothers me, I guess.
That said, I would try reinstalling, but I wouldn't be able to tell if it'd worked unless the problem never cropped up again in a long, long time. Sadly I also don't have access to my OSX discs at the moment (I'm out of the country).

Connecting Gigaworks ProGamer G500 to TV and PC at same time?

Yeah well thats my question. Is it possible to connect both to TV and PC at same time, and get 5.1 sound out of each? (not at same time though). Message Edited by mefi on 10-11-2007 03:47 AM

OOps sorry I wrote the wrong thing. It's been redone now.
Message Edited by mefi on 10-11-2007 03:48 AM

How do i get a still image to fade the same way and at the same time as a video?

I have a video stacked on top of a still image. When i add a transition, the still turns to a black screen while the video fades in accordance to the transition. How do i get the still image to fade the same way and at the same time as the video?

I do. I've applied it to both the still image and the video. Say i used the lens flare transition. If i apply it to both the video and the still image, the video will dissolve in to the next frame, but the still image will go to a black screen and then jump to the next frame. Its almost as if i inserted a black frame instead of a transition, but only for 2 seconds. Below is kind of a peek what it looks like.

Create SP that returns value and at the same time displays query result in output window

I would like create an SP which will return the records from the table and also return value to my c# client application.
For Example:
Select * from employee returns all the query results in output window.
Now I want to create an SP
Create procedure Test
As
Declare @ret int,
Select * from employee
set @ret = Select count(*) from employee
if @ret > 0
return 1
else
return 0
The above algo should return 1 0r 0 to c# client application and at the same time display all employees in sql query output window.
Can u pls help in this regard.

The above algo should return 1 0r 0 to c# client application and at the same time display all employees in sql query output window.
Why? and No!
Why? Your procedure generates a resultset of some number of rows. You check the resultset for the presence of rows to determine if "anything is there". You don't need a separate value to tell you this. Note that it helps
to post tsql that is syntactically correct. While we're at it, if you just need to know that rows exist there is no need to count them since that does more work than required. Simply test for existence using the appropriately-named function
"exists". E.g., if exists (select * from dbo.employee).
No! A stored procedure does not display anything anywhere. The application which executes the procedures is responsible for the consumption of the resultset; it chooses what to do and what to display.
Lastly, do not get into the lazy habit of using the asterisk in your tsql code. That is not best practice. Along with that, you should also get into the following best practice habits:
schema-qualify your objects (i.e., dbo.employee)
terminate every statement - it will eventually be required.

Airport modem and itunes streamed same time

Similar Messages

Maybe you are looking for