Airport network worked fine until I added a mid 2011 iMac

All devices on my airport extreme wifi network are experiencing slow or intermittent internet access since I added my new iMac. Additionally my Xbox hard hard wired to the AirPort Extreme is having connection issues. I purchased a mid 2011 iMac. I upgraded the OS to the 10.8.2 as soon as I got it setup so I have no real baseline of whether this is causing issues, however turning off wifi on the iMac seems to clear up the connectivity issues.

Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
10.4 instructions...
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.

Similar Messages

HT3819 I have an intel iMac OS 10.6.8 with iTunes 11.0.2 and an Apple TV with software 5.2. Home sharing worked fine until I added a VoIP device to my wired ethernet network. Now Apple TV cannot recognize my computer. How can I reconfigure?

I have an intel iMac OS 10.6.8 with iTunes 11.0.2 and an Apple TV with software 5.2. Home sharing worked fine until I added a VoIP device to my wired ethernet network. Now Apple TV cannot recognize my computer. How can I reconfigure?

I have an intel iMac OS 10.6.8 with iTunes 11.0.2 and an Apple TV with software 5.2. Home sharing worked fine until I added a VoIP device to my wired ethernet network. Now Apple TV cannot recognize my computer. How can I reconfigure?

Wifi problem: I have a airport wifi the small one with one port for modem. My Problem is airport wifi works fine however when I power off my IMac then power it up later on It does not show a connection I then have to manual do it my self it's a pain and n

I have a airport wifi the small one with one port for modem. My Problem is airport wifi works fine however when I power off my IMac then power it up later on It does not show a connection I then have to manual do it my self it's a pain and never happened before I have tried resetting the airport unit but still no luck please help.
Thank you
Roy from malden

Hi Roy, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.

Our airport extreme network works fine with our 6 devices. But when someone comes over and tries to log on, they can't until we restart the airport. Then they can get on, but it knocks one of our devices off the network. Any ideas?

Our airport extreme network works fine with our 6 devices. But when someone comes over and tries to log on, they can't until we restart the airport. Then they can get on, but it knocks one of our devices off the network. Any ideas?

I have not done a factory reset, I was trying to find out if I had some setting configured wrong first. I figured I'd just make things worse if went through a reset!
Here is a couple of screen shots:

I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. C

I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. Suddenly, the "timeout" is not allowing me to connect to my wireless network.

It could be that there's a new source of interference.
Use the advice in the second message of this thread to investigate the signal and noise levels that each client sees:
http://discussions.apple.com/thread.jspa?threadID=2347845&start=1
By the way, you've been misled by the poor field labeling into trying to type your entire message into the subject field, instead of putting a one-line topic description there.

I seriously don't know what caused this to start being a problem until today it worked fine, but I added an exception for popups full question in DETAILS

is there anyway to allow Firefox to allow pop ups from this 1 page of Facebook / well this 1 game https://apps.facebook.com/vampiresdarkside/ and not the entire pan in the Ass Pop up happy site, I cant see any sense in allowing popups from all
apps.facebook.com
and when I try to add it as the exception should be your program edits it to be that crap above instead of the exception I entered specifically,
apps.facebook.com/vampiresdarkside/
I seriously don't know what caused this to start being a problem until today it worked fine, but I added an exception for popups from this one site in Chrome and Firefox decided it wouldn't allow it popups from this part of Facebook and no I am not allowing all the FB apps to have popups I never had to before
apps.facebook.com/vampiresdarkside/
have popups after adding the popup exception in chrome, and no I did nothing to Firefox but it is kinda asking me to switch to Opera or some other crap browser with it acting like this, I modified the exception in chrome and Firefox now wont allow the pop ups it always had up until chrome allowed them WTF

Start Firefox in [[Safe Mode|Safe Mode]] to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
*Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
*Do NOT click the Reset button on the Safe Mode start window
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
Do a malware check with several malware scanning programs on the Windows computer.
Please scan with all programs because each program detects different malware.
All these programs have free versions.
Make sure that you update each program to get the latest version of their databases before doing a scan.
*Malwarebytes' Anti-Malware: http://www.malwarebytes.org/mbam.php
*AdwCleaner: http://www.bleepingcomputer.com/download/adwcleaner/ http://www.softpedia.com/get/Antivirus/Removal-Tools/AdwCleaner.shtml
*SuperAntispyware: http://www.superantispyware.com/
*Microsoft Safety Scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx
*Windows Defender: http://windows.microsoft.com/en-us/windows/using-defender
*Spybot Search & Destroy: http://www.safer-networking.org/en/index.html
*Kasperky Free Security Scan: http://www.kaspersky.com/security-scan
You can also do a check for a rootkit infection with TDSSKiller.
*Anti-rootkit utility TDSSKiller: http://support.kaspersky.com/5350?el=88446
See also:
*"Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked
*https://support.mozilla.org/kb/troubleshoot-firefox-issues-caused-malware

I have a 2007 iMac connected via WiFi. It has been working fine until I turned it on after a recent vacation. Network preferences indicates that it is correctly connected to my WiFI system but the data input and output rate is virtually zero. I know that

I have a 2007 iMac connected via WiFi. It has been working fine until I turned it on after a recent vacation. Network Preferences indicates that it is correctly connected to my WiFI system but the data input and output rate is virtually zero. I know that the WiFI signal is reaching the iMac since both my iPhone and iPad are working perfectly at that location. I have rebooted the router and the iMac to no avail. Any suggestions would be greatly appreciated. Thank you very much. Geoff

Hi Geoff,
Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
10.4 instructions...
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.

Hi there I have a iPhone 3G and it was with O2 but needed to go onto 3 network so someone on my local market unlocked it and the phone was working fine until I tried to update it through iTunes and it always now stops loading towards the end with an erro

Hi there
I ha
Hi there I have a iPhone 3G and it was with O2 but needed to go onto 3 network so someone on my local market unlocked it and the phone was working fine until I tried to update it through iTunes and it always now stops loading towards the end with an error is there a way to get the phone working again please.

Shame you had the iPhone hacked as O2 usually unlock their customers iPhones happily.
We cannot discuss your problem as it is in breach of the Ts&Cs you agreed to on registering
However hint ....you have probably trashed it

I have a 5s which has been working fine until about a week ago when any calender event added to my phone will not sync with my enterprise server. Any calender event entered on my PC (enterprise) does show on my phone. Mail is working fine both ways,ideas?

i have a 5s which has been working fine until about a week ago when any calender event added to my phone will not sync with my enterprise server. Any calender event entered on my PC (enterprise) does show on my phone. Mail is working fine both ways,ideas?Iphne 5s and enterprise

See my reply to this message:
https://discussions.apple.com/thread/2557520?start=15&tstart=0
The problem is that the POP3 client is not issuing a DELE command to remove the email from the server.

My apple tv was working fine untill the AirPlay option disappeared. I haven alterd the settings and have tryed rebooting both iPhone and ipad. I even rebooted the ATV and that disn't work. i am connected to the same network on both devices to.. Help

my apple tv was working fine untill the AirPlay option disappeared. I haven alterd the settings and have tryed rebooting both iPhone and ipad. I even rebooted the ATV and that disn't work. i am connected to the same network on both devices to. My iPad is up to date but my phone isn't but as I said mirroring and AirPlay worked fine on both devices befor...

Hi F1N5G10,
Thanks for contributing to the Apple Support Communities.
It sounds like you don't have the AirPlay option on your iOS devices. Restarting your Apple TV and iOS devices was a good first step, and you can find some additional tips to guide your troubleshooting at this link:
Resolve issues with AirPlay and AirPlay Mirroring from iPhone, iPad, and iPod touch - Apple Support
Sincerely,
Jeremy

WRT54Gv8 Works Fine, Until MacBook Connects to Network

Computer 1 = Athlon64 3200+ 2.01 GHz with XP Computer 2 = Toshiba laptop with Vista Basic Computer 3 = MacBook 2 GHz 10.4.9 Basically the network works fine with just Computer 1&2 connected, however minutes after Computer 3 connects it stops working. All the green lights are on and the signal strength is high, but everything just times out. I tried to fix this issue by upgrading the firmware to v8.00.2, however it always comes up with error message "Unable to get responses from server"

hi... reset the router back to factory default settings by pressing reset button on the back panel of the router...after resetting router, try upgrading firmware after upgrading firmware reset the router and reconfigure it check,whether it works or not, try tweaking up wireless settings on the router, change wireless channel to 11, go to advanced wireless settings and reduce beacon interval to 50, fragmentation and RTS threshold to 2304, change Transmission rate to 54Mbps, check whether it makes any difference or not.

Linksys Wireless Card (Linksys Router) in G4 Power Mac works fine until...

Linksys Wireless Card (Linksys Router) in G4 Power Mac works fine until...
new software upgrades on the 14 August 2006 (yesterday) which includes Airport 4.2.
The Linksys wireless PCI card (WMP54G) was installed just under a year ago with no problems. There was no need to install drivers, the Apple Mac recognised it and used it as a wireless card. I was browsing the internet last night (14 August) and the software updates downloaded in the background. Once it finished downloading, it requested for a re-start. I carried on browing the internet and then switched off my machine and went to bed.
When I turned on my computer in the morning, the wireless card no longer activates. The computer recognises there is a card but there is no connection to the router (meaning no internet). The router settings have not changed at all.
I believe it could be the Airport 4.2 update has interfered with the Linksys Card, but I'm not sure. I've been through all the Assist functions etc and there is no luck. It does seem that the big update released on the 14th August has played its part.
Any opinions and assistance on getting the card back to normal, and if possible assistance in removing the new updates to previous drivers/settings.
Thanks people.
G4 Power Mac Dual Processor Mirrored Doors Mac OS X (10.3.9)

Sorry, I do not have a solution for you but I have the same problem upgrading from Jaguar to Panther (on my home machine not listed which is a G3 b&w). Now my WMP54G doesn't see any wireless network (I used to be able to see several in the 'hood), and Apple Profiler recognizes the card. Apple updater changed the Airport system files, I believe.
Is it possible to find the old Airport software and install over current system to get it working again? I doubt Apple still offers the old airport software, but if someone has it, maybe it can be installed with Pacifist.
We need some wireless help here, community.
2.5 GHz Dual PowerMac G5 | 3GB RAM | SuperDrive Mac OS X (10.4.6)

I have reinstalled with Canons driver kit 2005b för Windows 7 64 bit. All works fine until the scann

Hi!
After Windows update in april 2014 I cant any longer use the scanning funktion via network from Canon MF8330 Cdn multifunktion printer/fax/scanner machine! It worked fine Before the april Windows update installation.
I have reinstalled with Canons driver kit 2005b för Windows 7 64 bit. All works fine until the scanner installation ends, then system report that it cannot install the scanner and I have to try installing again. I have done that now several times but it helps not. I Think it has something to do with that the Canon scanner drivers isn´t 64 bit files, or the problem is that windows update has replaces saome dll file to a never version that not work with Canon drivers.
I have seen that there is a service pack 1 from Canon för Windows 8 and 8,1, can I use that service pack to get a never dll file for scanner or work this only for windows 8 version.
Have someone a solution to this! I have contacted the Canon support already and they say that its a Microsoft problem!
Very thanful for help in this case!
Greetings
Sixten
Hi!
I am installing the drivers from Canons site. It is the newest version 2005b for Windows 7 64 bit to MF8330Cdn Canon multifunction printer/fax/scanner. Installation goes well for the printer and fax but not for scanner drivers. The error message is Could not install the scanner. In device manager is there then a unknown device under Image devices. In Device Manager I try to update drivers, but it does not help either, error message is access denied. I am logged on the system with administrator account, therfore it is strange that I get the error message access denied.
I tried earlier to do system restore back to previous time, but it did not work, error was that the system could not do the system restore because of access rights.
is there anything else I could do.
Here is the MF36SCN.inf file for scanner installation from Canon, if it can help You to go further with the problem. Is there something strange in the inf file that does not work in Windows 7 64 bit Windows, something shows that ther is also same 32 bits parts in the inf file.
Greetings
Sixten
; MF36SCN.INF -- Windows Setup File for the MF8300 Series (Windows XP,Vista(64-bit))
; Copyright CANON INC. 2009 All Rights Reserved
; InfID: {BA7E017E-FA42-4831-A084-AA9E671325EE}
; Last Modified: 11-Jun-2009
[Version]
Signature="$Windows NT$"
class="Image"
ClassGUID={6bdd1fc6-810f-11d0-bec7-08002be2092f}
; The above GUID is the class GUID for all scanners and MUST NOT change
Provider=%Msft%
CatalogFile.NTamd64=MF36SCN.CAT
DriverVer=06/17/2009, 11.3.0.0
[DestinationDirs]
DefaultDestDir=11
CNCDsFiles=10,"twain_32\"%CNCRFN%
CNCMediaFiles=10,media
ColorFiles.NT=11,spool\drivers\Color
[ControlFlags]
;ExcludeFromSelect=*
[Manufacturer]
%Mfg%=Models,NTamd64.5.1,NTamd64.6.0
[Models.NTamd64.5.1]
%LPTENUM\CNC.DeviceDesc%=CNCInstall_XP,USB\VID_04A9&PID_2708&MI_00
%LPTENUM\CNC.DeviceDesc%=CNCInstallNet_XP,CANON_MFNP&%CNCRFN%
[Models.NTamd64.6.0]
%LPTENUM\CNC.DeviceDesc%=CNCInstall_VISTA,USB\VID_04A9&PID_2708&MI_00
%LPTENUM\CNC.DeviceDesc%=CNCInstallNet_VISTA,CANON_MFNP&%CNCRFN%
;........................................ WinXP(64-bit) section
[CNCInstall_XP.NTamd64]
Include=sti.inf
Needs=STI.USBSection
SubClass=StillImage
DeviceType=1
DeviceSubType=0x1
DeviceData=CNCDeviceData
AddReg=CNCAddreg,CNCAddreg.USB,CNCUSDAddreg_XP
CopyFiles=WiaFiles,CNCDsFiles,ColorFiles.NT,MPScanLLD,CNCMediaFiles
ICMProfiles="sRGB Color Space Profile.icm"
; used for push button event
Capabilities=0x11
Events=PushButton.Events
DriverVer=06/17/2009, 11.3.0.0
FriendlyName=%CNC.FriendlyName%
[CNCInstall_XP.NTamd64.Services]
Include=sti.inf
Needs=STI.USBSection.Services
[CNCInstall_XP.NTamd64.CoInstallers]
CopyFiles = ScanCoInstaller_CopyFiles_x64
AddReg    = ScanCoInstaller_AddReg_x64
[ScanCoInstaller_CopyFiles_x64]
CNCLSO36b.dll
[ScanCoInstaller_AddReg_x64]
HKR,,CoInstallers32,0x00010000,"CNCLSO36b.dll,Coinstaller_EntryPoint"
;........................................ WinVista(64-bit) section
[CNCInstall_VISTA.NTamd64]
Include=sti.inf
Needs=STI.USBSection
SubClass=StillImage
DeviceType=1
DeviceSubType=0x1
DeviceData=CNCDeviceData_VISTA
AddReg=CNCAddreg,CNCAddreg.USB,CNCUSDAddreg_XP,CNCUSDAddreg_VISTA
CopyFiles=Wia2Files,CNCDsFiles,ColorFiles.NT,MPScanLLD,CNCMediaFiles
ICMProfiles="sRGB Color Space Profile.icm"
; used for push button event
Capabilities=0x11
Events=PushButton.Events
DriverVer=06/17/2009, 11.3.0.0
FriendlyName=%CNC.FriendlyName%
[CNCInstall_VISTA.NTamd64.Services]
Include=sti.inf
Needs=STI.USBSection.Services
[CNCInstall_VISTA.NTamd64.CoInstallers]
CopyFiles = ScanCoInstaller_CopyFiles_x64
AddReg    = ScanCoInstaller_AddReg_x64
[ScanCoInstaller_CopyFiles_x64]
CNCLSO36b.dll
[ScanCoInstaller_AddReg_x64]
HKR,,CoInstallers32,0x00010000,"CNCLSO36b.dll,Coinstaller_EntryPoint"
;........................................ WinXP(64-bit) section(Network)
[CNCInstallNet_XP.NTamd64]
Include=sti.inf
Needs=STI.SerialSection
SubClass=StillImage
DeviceType=1
DeviceSubType=0x1
DeviceData=CNCDeviceData
AddReg=CNCAddreg,CNCUSDAddreg_XP
CopyFiles=WiaFiles,CNCDsFiles,ColorFiles.NT,MPScanLLD,CNCMediaFiles
ICMProfiles="sRGB Color Space Profile.icm"
; used for push button event
Capabilities=0x11
Events=PushButton.Events
DriverVer=06/17/2009, 11.3.0.0
FriendlyName=%CNC.FriendlyName%
[CNCInstallNet_XP.NTamd64.Services]
Include=sti.inf
Needs=STI.SerialSection.Services
[CNCInstallNet_XP.NTamd64.CoInstallers]
CopyFiles = ScanCoInstaller_CopyFiles_x64
AddReg    = ScanCoInstaller_AddReg_x64
[ScanCoInstaller_CopyFiles_x64]
CNCLSO36b.dll
[ScanCoInstaller_AddReg_x64]
HKR,,CoInstallers32,0x00010000,"CNCLSO36b.dll,Coinstaller_EntryPoint"
;........................................ WinVista(64-bit) section(Network)
[CNCInstallNet_VISTA.NTamd64]
Include=sti.inf
Needs=STI.SerialSection
SubClass=StillImage
DeviceType=1
DeviceSubType=0x1
DeviceData=CNCDeviceData_VISTA
AddReg=CNCAddreg,CNCUSDAddreg_XP,CNCUSDAddreg_VISTA
CopyFiles=Wia2Files,CNCDsFiles,ColorFiles.NT,MPScanLLD,CNCMediaFiles
ICMProfiles="sRGB Color Space Profile.icm"
; used for push button event
Capabilities=0x11
Events=PushButton.Events
DriverVer=06/17/2009, 11.3.0.0
FriendlyName=%CNC.FriendlyName%
[CNCInstallNet_VISTA.NTamd64.Services]
Include=sti.inf
Needs=STI.SerialSection.Services
[CNCInstallNet_VISTA.NTamd64.CoInstallers]
CopyFiles = ScanCoInstaller_CopyFiles_x64
AddReg    = ScanCoInstaller_AddReg_x64
[ScanCoInstaller_CopyFiles_x64]
CNCLSO36b.dll
[ScanCoInstaller_AddReg_x64]
HKR,,CoInstallers32,0x00010000,"CNCLSO36b.dll,Coinstaller_EntryPoint"
;.......................................... Common Section
[PushButton.Events]
PushButtonPushed1=%PushButtonPushed1%,{66F2A894-EC9B-430c-9D52-E8719D200DAC},%ButtonApp%
PushButtonPushed2=%PushButtonPushed2%,{506AC8D1-E030-4f05-8F8A-4476153E2D6C},%ButtonApp%
PushButtonPushed3=%PushButtonPushed3%,{9813E8A6-3652-4768-9AD1-C89E9B5CA956},%ButtonApp%
PushButtonPushed4=%PushButtonPushed4%,{03B58D10-0245-4859-A489-D695C7729FB3},%ButtonApp%
[ColorFiles.NT]
CNZ005.ICC
CNFR08.ICC
[CNCDeviceData]
TwainDS=%CNC.TwainDS%
SpecialInfo=%CNC.SPInfo%
DeviceKey=%CNCRFN%
InstallDirectory="\TWAIN_32\%CNCRFN%\"
KeyNamePath=%KEYNAME%
DefaultKeyNamePath=%DEFAULTKEYNAME%
[CNCDeviceData_VISTA]
TwainDS=%CNC.TwainDS%
SpecialInfo=%CNC.SPInfo%
DeviceKey=%CNCRFN%
InstallDirectory="\TWAIN_32\%CNCRFN%\"
KeyNamePath=%KEYNAME%
DefaultKeyNamePath=%DEFAULTKEYNAME%
UI Class ID={DF89C549-D67D-4fb0-A575-547073BFAB11}
;The above GUID reused from sample MUST change for each Model.
[CNCAddreg]
HKLM,"%SGDKEY%","DeviceName",,%CNC.MDL%
HKLM,"%SGDKEY%","SeriesName",,%CNC.SRS%
HKLM,"%SGDKEY%","Manufacturer",,"Canon Inc."
HKLM,"%SGDKEY%","ProductFamily",,"TWAIN Scanners"
HKLM,"%SGDKEY%","ProductName",,%CNC.MDL%
HKLM,"%SGDKEY%","InstallDirectory",,"%10%\TWAIN_32\%CNCRFN%\"
HKLM,"%SGDKEY%","DeviceDriver",,"SCANINTF.DLL"
HKLM,"%SGDKEY%","ProductId",,"MF8300          "
HKLM,"%SGDKEY%","DataSourcePath",,"%10%\TWAIN_32\%CNCRFN%\cisds.ds"
HKLM,"%SGDKEY%","TextEnhance",0x00010001,0
HKLM,"%SGDKEY%","HiDefinitionMode",0x00010001,0
HKLM,"%SGDKEY%","AutoPreview",0x00010001,0
HKLM,"%SGDKEY%","AutoClose",0x00010001,0
HKLM,"%SGDKEY%","SavePreview",0x00010001,1
HKLM,"%SGDKEY%","DriverDate",,"06 2009"
HKLM,"%SGDKEY%","DriverVersion",,"11.3.0.0.mf09"
HKLM,"%SGDKEY%","ColorGear",,%CNC.ColorGear%
HKLM,"%SGDKEY%","ColorMatch Platen",,"CNFR08.ICC"
HKLM,"%SGDKEY%","SGIPPDEF",,"CNCFR08.DAT"
HKLM,"%SGDKEY%","Descreen",0x00010001,0
HKLM,"%SGDKEY%","Unsharp",0x00010001,3
HKLM,"%SGDKEY%","MultiLimitThreshold",0x00010001,180
HKLM,"%SGDKEY%","MultiJackUp",0x00010001,9
HKLM,"%SGDKEY%","MultiTrimJackUp",0x00010001,20
HKLM,"%SGDKEY%","CardPhotoDistThr",0x00010001,30
HKLM,"%SGDKEY%","PhotoTrimThr",0x00010001,210
HKLM,"%SGDKEY%","PhotoRThr",0x00010001,210
HKLM,"%SGDKEY%","PhotoGThr",0x00010001,210
HKLM,"%SGDKEY%","PhotoBThr",0x00010001,210
HKLM,"%SGDKEY%","CardTrimThr",0x00010001,30
HKLM,"%SGDKEY%","CardRThr",0x00010001,30
HKLM,"%SGDKEY%","CardGThr",0x00010001,30
HKLM,"%SGDKEY%","CardBThr",0x00010001,30
HKLM,"%SGDKEY%","ParWhiteBlackEth",0x00010001,5
HKLM,"%SGDKEY%","ParWhiteBlackEthDG",0x00010001,5
HKLM,"%SGDKEY%","ParWhiteBlackSth",0x00010001,35
HKLM,"%SGDKEY%","ParWhiteBlackVth",0x00010001,10
HKLM,"%SGDKEY%","ParLabelingHth",0x00010001,30
HKLM,"%SGDKEY%","ParLabelingLeft",0x00010001,1
HKLM,"%SGDKEY%","ParLabelingTop",0x00010001,1
HKLM,"%SGDKEY%","ParLabelingRight",0x00010001,1
HKLM,"%SGDKEY%","ParLabelingBottom",0x00010001,1
HKLM,"%SGDKEY%","DT_Left",,"10"
HKLM,"%SGDKEY%","DT_Top",,"0"
HKLM,"%SGDKEY%","DT_Width" ,,"1.5"
HKLM,"%SGDKEY%","DT_Length",,"4.5"
HKLM,"%SGDKEY%","DT_Border_1",,"2.5"
HKLM,"%SGDKEY%","DT_Border_2",,"3.5"
HKLM,"%SGDKEY%","DT_BkTh",,"18"
HKLM,"%SGDKEY%","DT_MinWhThr",,"15"
HKLM,"%SGDKEY%","DT_MaxWhThr",,"45"
HKLM,"%SGDKEY%","ButtonNum",0x00010001,1
HKLM,"%STIKEY%","MF8300",0x00010001,1
[CNCAddreg.USB]
HKLM,"%SGDKEY%","AvailableDriver",0x00010001,1
[CNCUSDAddreg_XP]
HKLM,"%WIASGDKEY%","ColorMatch",0x00010001,1
HKLM,"%WIASGDKEY%","ColorGear",,"%CNC.ColorGear%"
HKLM,"%WIASGDKEY%","TextEnhance",0x00010001,0
HKLM,"%WIASGDKEY%","Descreen",0x00010001,0
HKLM,"%WIASGDKEY%","UnsharpMask",0x00010001,0
HKLM,"%WIASGDKEY%","HiDefinitionMode",0x00010001,0
HKLM,"%WIASGDKEY%","ProductId",,"MF8300          "
HKLM,"%WIASGDKEY%","ButtonNum",0x00010001,1
HKLM,"%WIASGDKEY%","DspGamma",0x00010001,1
HKLM,"%WIASTIKEY%","MF8300",0x00010001,1
HKR,,USDClass,,"{4BA01336-9934-455e-8FB8-4A47A638DF0E}"
HKCR,CLSID\{4BA01336-9934-455e-8FB8-4A47A638DF0E},,,"Canon USD"
HKCR,CLSID\{4BA01336-9934-455e-8FB8-4A47A638DF0E}\InProcServer32,,,%11%\CNCC8300.DLL
HKCR,CLSID\{4BA01336-9934-455e-8FB8-4A47A638DF0E}\InProcServer32,ThreadingModel,,"Both"
; The above GUID is specific to MF8300 and MUST change for a different model.
[CNCUSDAddreg_VISTA]
HKCR,CLSID\{DF89C549-D67D-4fb0-A575-547073BFAB11},,,"WIA Driver UI Extension"
HKCR,CLSID\{DF89C549-D67D-4fb0-A575-547073BFAB11}\shellex\ImageProcessingFilter\{CA0D4D3E-98ED-4787-AF02-4AF2A1303ACC}
; The above GUID is specific to MF8300 and MUST change for a different model.
HKCR,CLSID\{CA0D4D3E-98ED-4787-AF02-4AF2A1303ACC},,,"Canon Image Processing Filter"
HKCR,CLSID\{CA0D4D3E-98ED-4787-AF02-4AF2A1303ACC}\InProcServer32,,,%11%\CNCE8300.dll
HKCR,CLSID\{CA0D4D3E-98ED-4787-AF02-4AF2A1303ACC}\InProcServer32,ThreadingModel,,"Both"
; The above GUID is specific to MF8300 and MUST change for a different model.
[WiaFiles]
CNCC8300.DLL
CNCI8300.DLL
CNCL8300.DLL
[Wia2Files]
CNCC8300.DLL
CNCI8300.DLL
CNCL8300.DLL
CNCE8300.DLL
[CNCDsFiles]
CISDS.DS
SGUI.DLL
SGUI_RES.DLL
WIARES.DLL
IOP.DLL
ITLIB32.DLL
SCANINTF.DLL
TPM.DLL
CNCFR08.DAT
MC2.TXT
JDA_CIMG.DLL
NBS4MB.DLL
NBSCOR4M.DLL
RMSLANTC.DLL
RSTCOL.DLL
[MPScanLLD]
CNCMFP36.INI,,,0x20
CNCLSI36b.DLL,,,0x20
CNCLSD36b.DLL,,,0x20
CNCLSC36b.DLL,,,0x20
CNCLST36b.DLL,,,0x20
CNCLSU36b.DLL,,,0x20
[CNCMediaFiles]
CSSAMP1.MID
;-------------------------------Source Index
[SourceDisksFiles]
CNZ005.ICC=1
ITLIB32.DLL=1
JDA_CIMG.DLL=1
NBS4MB.DLL=1
NBSCOR4M.DLL=1
RMSLANTC.DLL=1
RSTCOL.DLL=1
CISDS.DS=1
SGUI.DLL=1
IOP.DLL=1
SCANINTF.DLL=1
TPM.DLL=1
SGUI_RES.DLL=1
WIARES.DLL=1
CSSAMP1.MID=1
CNCFR08.DAT=1
CNFR08.ICC=1
MC2.TXT=1
CNCC8300.DLL=1
CNCI8300.DLL=1
CNCL8300.DLL=1
CNCE8300.DLL=1
CNCMFP36.INI=1
CNCLSI36b.DLL=1
CNCLSD36b.DLL=1
CNCLSC36b.DLL=1
CNCLST36b.DLL=1
CNCLSU36b.DLL=1
CNCLSO36b.DLL =1
[SourceDisksNames]
1=%D1%,scan.cab,
;-------------------------------String Aliases
[Strings]
Msft="Canon"
Mfg="Canon"
SGDKEY="Software\Wow6432Node\Canon\SateraMFP1\ScanGear\11.3\Devices\MF8300"
STIKEY="Software\Wow6432Node\Canon\SateraMFP1\ScanGear\STI"
DEFAULTKEYNAME="Software\Wow6432Node\Canon\SateraMFP1\Toolbox Ver4.9\Devices\"
KEYNAME="\Software\Canon\MFToolbox\"
WIASGDKEY="Software\Canon\SateraMFP1\WIA\3.0\Devices\MF8300"
WIASTIKEY="Software\Canon\SateraMFP1\WIA\STI"
D1="Canon MF8300 Series Setup Disk"
LPTENUM\CNC.DeviceDesc="Canon MF8300 Series"
ButtonApp        = "MF Toolbox Ver4.9"
CNCRFN           = "MF8300"
CNC.MDL          = "Canon MF8300"
CNC.SRS          = "Canon MF8300 Series"
CNC.DeviceDesc   = "Canon MF8300"
CNC.SPInfo       = "Canon MF8300 Scanner"
CNC.TwainDS      = "Canon MF8300 Series"
CNC.ColorGear    = "FR08"
PushButtonPushed1= "Scan-1"
PushButtonPushed2= "Scan-2"
PushButtonPushed3= "Scan-3"
PushButtonPushed4= "Scan-4"
CNC.FriendlyName     = "WIA Canon MF8300 Series"
greeting
Sixten

How I fixed it, at least for now:
1. I've been using OC Genie for a few days, it has been working great on Windows but I guess it was causing many games to crash to the desktop so I decided to turn it off, since then the memory issue started to happen, since this morning.
2. I can only think of my computer got OC Genie addicted, like addiction to crack or cocaine, and the memory, or call it nervous system, wanted more OC Genie, so it gave it to him and bingo, my 4GB readable, but then I used of trickery and deceit to disable OC Genie again and my 4GB is back again without OC Genie.
Hope this helps someone.

I am trying to export a video from Premiere Pro. I have both audio and video checked and the sequence is active but only the audio exports. There is no video at all. Can anyone tell me how to get the video to export. It was working fine until today.

Premiere Pro CC has been working fine until today. I have completed my sequence and it is active. I have both audio and video checked when I am exporting using H.264 with Match Source Hi bitrate. I am choosing entire sequence. The audio exports but the video and title does not. Can anyone tell me how to troubleshoot this so I can complete this project? Please!

Greetings,
I've never seen this issue, and I handle many iPads, of all versions. WiFi issues are generally local to the WiFi router - they are not all of the same quality, range, immunity to interference, etc. You have distance, building construction, and the biggie - interference.
At home, I use Apple routers, and have no issues with any of my WiFi enabled devices, computers, mobile devices, etc - even the lowly PeeCees. I have locations where I have Juniper Networks, as well as Aruba, and a few Netgears - all of them work as they should.
The cheaper routers, Linksys, D-Link, Seimens home units, and many other no name devices have caused issues of various kinds, and even connectivity.
I have no idea what Starbucks uses, but I always have a good connection, and I go there nearly every morning and get some work done, as well as play.
You could try changing channels, 2.4 to 5 Gigs, changing locations of the router. I have had to do all of these at one time or another over the many years that I have been a Network Engineer.
Good Luck - Cheers,
M.

I merge projects in aperture, it works fine until aperture restarts. After aperture restarts, the projects are no longer merged, and are back the way they were. Can anyone suugest how to make the merge permanent?

I merge projects in aperture, it works fine until aperture restarts. After aperture restarts, the projects are no longer merged, and are back the way they were. Can anyone suugest how to make the merge permanent?

I tried the first aid tasks but the issue is still there. I have more info now though. It's not a problem with merging.
The problem is that new projects are being generated everytime aperture starts (with the same name, ie 01, 02.... and 01 (1), 02 (1) .....)
When aperture start, it shows "importing". When I click on importing, it goes into the activity box. In the activity box, has many lines as below. The added projcts are all empty. It's annoying because i have many useless projects being generated.

Airport network worked fine until I added a mid 2011 iMac

Similar Messages

Maybe you are looking for