Airport no longer recognizes dsl, defaults to ehternet.

Recently airport extreme defaulted to connect to the internet via ethernet instead of the dsl modem. I have tried to reset using admin. Here it is set for dsl. Howver in internet connection it shows connect to the internet via ethernet. End result is I cannot connect using airport. I cannot find where to change the configuration to earthlink dsl. Options listed show modem, built-in ethernet or AOL dsl. Looking to be pointed in the right direction.
Imac Mac OS X (10.3.3)

Fred first welcome to the discussions.
It maybe that I am having one of those OLD moments.
Let me see if I can help.
If you go to your Apple and click and then choose System Preferences and next choose Network. The box will open and give you 3 choices.
Airport (Wireless)
Built In Ethernet ( Hardwired with Cat 5 or 6 Cable)
Internal Modem ( Dial-up)
To have a wireless connection, you must also have a Wireless Router.
Your Internet Service Provider furnishes you with one of several different Modems, or at additional charge some offer a combined Modem Router.
The typical set-up is your ISP's Modem will be connected to the WAN port of your Wireless Router. This enables you to get a wireless connection.
In the Network Settings your type of connection must have the green dot highlighted and at the top of the list. To get it to the top is drag your choice to the top of the list.
Otherwise if you only have your ISP's modem you can only connect with and ETHERNET CABLE (Hardwired) unless you have a Wireless Router or a Modem Router combined.
http://www.apple.com/support/airport/
This link has all of the information you need.
Good Luck Don

Similar Messages

Airport utility no longer recognizes my Airport Extreme Base Station, which had been set up to extend a wifi network

Hi. In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds. Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended. I folllowed all the directions from the apple support pages, and finally got it to work. I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension. Then a week or so ago I noticed that my laptop would no longer connect to my base station. I did not have time to look into it until this week. Airport utility, either on my Mac or iphone no longer recognizes my base station. My mac is running OS X 10.10.1 and my iPhone is running iOS 8.1.2 I have tried both hard, soft and factory resets of my base station to no avail. The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before. I can't actually connect to it, but it does try. Then after approximately 5 minutes, it disappears from my list.
Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c? airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software. I am attaching an image of that.
Thank you,
John
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?

I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature.

Airport Extreme no longer recognizes my Express when I try to password protect the network

When I try to protect my network with a password, my airport extreme no longer recognizes my airport express. How can I fix this so I can connect my network and still use my network for airtunes??

I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature.

Palm TX no longer recognizes SD cards!!!

I have two Palm TX's and have been using Lexar SD, Sandisk SD, and Sandisk Ultra II SD cards (all are 2G cards) for months without any problems. This past week, I went through airport security with both TX's and all these cards, and now all but 1 SD card is NO longer recognized by the TX. I have done a soft reset, a hard reset, and still these cards cannot be recognized (the TX's message) by the unit. The odd thing is one TX can recognize one of the 2G cards just fine. Weird
I tried a 512M Lexar SD card, but it couldn't recognize that one either and the 512M card never went through airport security, it stayed home.
Any idea what is wrong or what I can do? Anyone experience this themselves?
Thank you - R
Post relates to: Palm TX
Message Edited by rouge2009 on 04-06-2009 11:23 AM

To clarify, they both went through the metal detectors and were placed in my carry-on luggage. Everything I've read online so far tells me that these machines should not harm my Palm TX, but both are experiencing the same issues. They can no longer recognize ANY SD cards. Is the card port shorted out or something? When I insert a card, the TX asks me if I want to format it, when I tap 'yes', it then tells me it cannot recognize the card. When I tap on 'card info', it recognizes there is an SD card inserted, but cannot read any of the specifics of the card. PLEASE, someone...help.......

Just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

Temporarily connecting your AirPort Express to one of the Time Capsule's Etherent LAN <-> ports...as LaPastenagure suggests....is always a good way to setup and configure other network devices.
If you want to configure the Express using wireless, remember that the Express broadcasts a default wireless signal with a name like Apple Network xxxxxx. You must log on to this network first....no password is required....then open AirPort Utility to "see" the AirPort Express.

I recently upgraded iTunes to 11.1.4.62 and then itunes would no longer recognize my iphone 4s and iPod

I recently upgraded iTunes to 11.1.4.62 and then itunes would no longer recognize my iphone 4s and iPod although I can see the iphone but NOT the iPod on the computer (windows 8.1 Pro). I checked everything , cable, services, stop and start and automatice, etc.and went through all the steps on the apple support site, to include removing all apple software in the designated order and reinstalling it. iTunes still doesn't see the iphone.
The Apple iPhone shows up only under protable Devices in the Device Manager window and has a Yellow ! warning triangle, and there is no Apple USB controller in the devices menu.under Universal Serial Bus Controllers. When I look under the properties of the Apple iphone, it says in Device Status, to reinstall the drivers for this device (Code 18).
When I do this, I get the following: "Windows found driver softweare for you device but encountered an error when attempting to install it" Apple Mobile Device Driver One of the installers for th this device cannot perform the installation at this time. I tried both suggested locations on the C: drive.
Also I can't seem to find out how to install the Apple USB Contoller or is that related to the problem above?
The iphone and my ipod work fine with this version of itunes on Windows 7 on my laptop. is it possible that I am missing a critical update from Microsoft on the driver and USB controller? I have been leery of installing them since my computer had problems with some updates in January.
I 've tried every thing listed in this forum, I think, and the Apple support page on this subject. Please help!

Version 11.1.5.5 of iTunes was just released today. If you update to that, does that help with the recognition troubles?
http://www.apple.com/itunes/download/

I'd love some help trying to figure out why my 2008 MacBook no longer recognizes my external drive and now is not downloading photos from my iphone....?

After many years of having no problems at all on my Macbook, I recently figured I should finally upgrade my OS. I did that about three weeks ago, updating to Snow Leopard (10.6.8). I used Time Machine at least once after the OS upgrade but now Time Machine no longer recognizes the external drive I have used for all these years to back up. The MacBook does not "see" it. (Disk Utility does however.) The computer then also stopped recognizing another La Cie back-up that I have and now... my iPhone cannot download photos? Yikes.
I have, of course, shut down numerous times, used different cables (that worked for some) and the two USB drives. I even used a firewire. Nothing worked. I also tried to "Repair disk" on Disk Utility. It didn't work either, giving me an error (that I didn't save, sorry).
I read many other discussions on the file format of the external drive and of course I'd be happy to reformat the external drives--however, it is obviously a tad nerve-wracking to reformat drives before having an accessible back-up. Suggestions? I do not remember what file format they have but am pretty sure it's not the Mac file system someone mentioned. The drives are a 2009 WD "My Passport Elite" and La Cie 2007 d2 Quadra,
In terms of other hardware available, we do have another MacBook Air but it has started rejecting both drives as well (without the Snow Leopard upgrade). We have an old Dell but it wouldn't have the disk space to help out much.
Any thoughts on the process involved would be welcome. Any ideas on the iPhone rejection would be helpful as well! It is a 30gig iPhone 4 that has 20 or so gigs free (not clear as iTunes says that there are abour 18 Gigs on the phone but 24 free gigs? I may be bad at math but that's 40 gigs...).
I am checking out iCloud but apparently there are only 55 gigs available?
Will be glad to hear any thoughts. Thanks!

Good afternoon Lyssa,
Phew. First of all, thanks in advance...these blogs are always comforting help!
So, to answer your questions: For the age of the hard drive.Well, I added memory a couple of years ago (RAM and hard drive). Being a mom leads me to eat up a fair amount of gigs with photos of my kids and, in fact, I think I entirely replaced the original drive, so it is a couple years younger than 2008 since I did that in March 2010. If there is some way to verify that (whether or not I replaced the entire drive), I'm all ears. I have 311 Gigs free, so it is not a space issue. I verified the startup disk on Disk Utilityand nothing showed up.
Question 1- What formats...
The La Cie is format Windows NT Filesystem 3G ....At the time that I bought it I was still using a PC as well as a Mac and was told by afriend to use this format...
The WD is Mac OS Extended (Journaled). I again tried to repair the WD last night and this is the error message: "Error: DiskUtility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files."
Also, Time Machine tried again to back-up and gave me this error: "Files can't becopied onto the backup disk because it appears to be 'read only'. You may needto repair or reformat the disk using Disk Utility. If the disk can't berepaired, you must use a different disk for backups. Open Time Machinepreferences to select a different backup disk."
Question 2. Other cables...
I used two other cables with the WD and that didn't change anything.
Question 3... Fire Wire from the La Cie
Yes, I used the Firewire cable from the La Cie and it is indeed present, though still not visible in Finder. Since it is not Mac OSExtended I know that I can't use Time Machine with it.
So, in summary...
I can plug in the La Cie and it is functional on the MacBook, visible on Disk Utility but not visible in Finder. The WD drive is not visible and not functional. So we can think it is indeed the WD that is not working.... Also, the iphone photos did, in the end, get downloaded, so it is not something more general.
Causes...
I forgot to mention that there is a "lost+found" file on the WD which apparently points to a UNIX /OS issue?
Some kind of "insurance"?....
I'm curious about how people avoid this kind of issue. You just regularly replace back-up drives and hard drives before problems come up? Time Machine is great and saves many of us from disasters, however, knowing that your Time Machine back-ups are vulnerable makes the whole system insecure. No way to have alarms ring before the drive goes out?
As for ways ahead...
It seems that I ought to be able to copy off of the WD to the MacBook then erase it and reformat it and start over again. However, I haven’t been able to see its contents except on random occasions. If you have any ideas on how to copy the Time Machineback-ups from the WD, again, I'm all ears!
Good afternoon Lyssa,
Phew. First of all, thanks in advance...
So, to answer your questions:
For the age of the hard drive. Well, I added memory a coupleof years ago (RAM and hard drive). Being a mom leads me to eat up a fair amountof gigs with photos of my kids ….and, in fact, I think I entirely replaced theoriginal drive, so it is a couple years younger than 2008 since I did that inMarch 2010. If there is some way to verify that, I'm all ears. I have 311 Gigfree, so it is not a space issue. I verified the startup disk on Disk Utilityand nothing showed up.
Question 1- What formats...
The La Cie is format Windows NT Filesystem 3G ....At thetime that I bought it I was still using a PC as well as a Mac and was told by afriend to use this format...
The WD is Mac OS Extended (Journaled). I again tried torepair the WD last night and this is the error message: "Error: DiskUtility can’t repair this disk. Back up as many of your files as possible,reformat the disk, and restore your backed-up files."
Also, Time Machine tried again to back-up and gave me thiserror: "Files can't be copied onto the backup disk because it appearsto be 'read only'. You may need to repair or reformat the disk using DiskUtility. If the disk can't be repaired, you must use a different disk forbackups. Open Time Machine preferences to select a different backup disk."
Question 2. Other cables...
I used two other cables with the WD and that didn't changeanything.
Question 3... Fire Wire from the La Cie
Yes, I used the Firewire cable from the La Cie and it isindeed accessible, though still not visible in Finder. Since it is not Mac OSExtended I know that I can't use Time Machine with it.
FYI...
So, in summary... I can plug in the La Cie and it is “functional” on theMacBook but not visible in Finder. The WD drive is not visible and notfunctional. So we can think it is indeed the WD that is not working.... ALSO,the iphone photos did, in the end get downloaded.
As for ways ahead…
It seems that I ought to be able to copy off of the WD tothe MacBook then erase it and reformat it and start over again. However, Ihaven’t been able to “see” its contents except on random occasions…
Any further thoughts are welcome!

ITunes and iCloud no longer recognize Outlook on my computer

Since I got my iPhone several years ago, I have used Outlook via iTunes to sync my calendar, contacts, and other information.
I currently have an iPhone 4 with OS 5; I unfortunately have iTunes 10.5.2 running on a Windows 7 operating system.
I say "unfortunately" because despite my satisfaction with how these things all worked together, I am now totally fed up with Apple and it's supposed updates.
Today is Dec. 14, 2011. Two days ago, Apple released an "update" to supposedly address an audio issue. This morning, my computer and iPhone spoke to each other using iTunes -- I chose not to use iCloud when I downloaded the new OS 5.0 because I was not satisfied that it was consistently updating what I needed on my phone. It seems all it wants to do is update to iCloud.
This morning, an Apple alert about a new update showed up on my screen and I said okay to install because in the past there have been been few issues. NONE have caused my iTunes to insist there is no supported calendar program or to not show Outlook as an option for contacts.
This morning pre-update: everything worked as it was supposed to; after the update: NOTHING is working the way it is supposed to.
This ***** and is stupid, APPLE. It is very easy to get another kind of smartphone and these are all catching up with iPhone.
Issuing updates that make the system not work and WASTE HOURS OF MY TIME is no way to keep me as a customer or a way to encourage me to buy more apple products.
IN SUMMARY:
iPhone 4 with OS 5.0
iTunes 10.5.2 with Dec. 14 update
NO LONGER RECOGNIZES OUTLOOK ON MY SYSTEM.
I have wasted hours trying to fix this.

Hi, Linda from Folsom. Thanks for the message.
While I do run iolo system mechanic, my issues did not start until *after* I downloaded iTunes 10.5.2.
On the same date I updated iTunes, I also downloaded a Java update. I did these one after the other so didn't now which updated started the issue.
I later found that my issues were also related to iCloud usage for syncing, which I resolved this week by eliminating iCloud from my life (other than backing up my iPhone).
I posted something in the community about how I undid everything iCloud did to my Outlook, but my solution is only for those who no longer want to use iCloud with Outlook.
That's an interesting point about the iolo system because I didn't have any issues at all with it (until I updated iTunes).
I had a very similar system setup at the time as you do:
iPhone 4 with OS 5.0.1
Outlook 2007 (now I have 2010 version)
iTunes 10.5.2
Windows 7 home premium (now I have the Windows 7 ultimate version).
I will be interested to hear if your iolo system caused some issues as I do like using it for clean up on my hard drive. When I couldn't use Outlook, I went to "JustAsk.com" and paid the small fee to find out that you can repair office from the control panel programs list; this is what solved my issue.
If you haven't tried it, it's pretty easy:
Open Control Panel
Select Programs
Find Office on the programs list
RIGHT click on it
Select repair
Windows installer runs, then restart
After I did that, iPhone could see Outlook again. That could be where the registry issue is happening with iolo.
Hope this is helpful,
Cecilia

Installed latest itunes update and computer tried to burn a playlist to CD and realized computer no longer recognizes my CD/DVD drive. This is an APPLE Itunes issue. Help!. HPPavillion DV6 64 bit, windows 7

Installed latest itunes update and computer tried to burn a playlist to CD and realized computer no longer recognizes my CD/DVD drive. After doing some data mining, found out from community this is an long standing APPLE problem- which doesn't get much tech support in terms of fixes. I have an HPPavillion DV6 64 bit, Windows 7 OS . After reading an earlier complaint from 2009 in the support community, I ran diagnostics from ITunes which gave the following result. Can someone please help? (I'm not enough of a techie to know what I'm doing or how to locate /reinstall CD drivers. I am searching for driver disc but cannot locate.)
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
Hewlett-Packard HP Pavilion dv6 Notebook PC
iTunes 10.6.3.25
QuickTime 7.7.2
FairPlay 1.14.43
Apple Application Support 2.1.9
iPod Updater Library 10.0d2
VoiceOver Kit 1.4.2 (222093/222742)
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 5.2.0.6
Apple Mobile Device Driver 1.59.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 0043AC7C0368E428
Current user is not an administrator.
The current local date and time is 2012-07-24 23:43:08.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
ATI Technologies Inc., AMD M880G with ATI Mobility Radeon HD 4250
**** External Plug-ins Information ****
No external plug-ins installed.
iPodService 10.6.3.25 (x64) is currently running.
iTunesHelper 10.6.3.25 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.

Doublechecking ... did you have CD/DVD drive tests checked when you ran those diagnostics? (I'm not seeing the CD/DVD test results down the bottom of the results where I'd expect to see them.)
For example, here's what I get:
Microsoft Windows 7 x64 Ultimate Edition Service Pack 1 (Build 7601)
Acer Aspire X3400
iTunes 10.6.3.25
QuickTime 7.7.2
FairPlay 1.14.43
Apple Application Support 2.1.9
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 5.2.0.6
Apple Mobile Device Driver 1.59.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 003CAD7C0A1258F8
Current user is not an administrator.
The current local date and time is 2012-07-26 10:42:53.
iTunes is not running in safe mode.
WebKit accelerated compositing is disabled.
HDCP is supported.
Core Media is not supported. (16008)
Video Display Information
ATI Technologies Inc., AMD Radeon HD 6570
**** External Plug-ins Information ****
No external plug-ins installed.
Genius ID: d6a87ba725121aa1240b1ce936c23470
iPodService 10.6.3.25 (x64) is currently running.
iTunesHelper 10.6.3.25 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
**** CD/DVD Drive Tests ****
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),
E: ATAPI DVD A DH16ABSH, Rev YA12
Data or MP3 CD in drive.
Found 1 songs on CD, playing time 255:57 on CDROM media.
Track 1, start time 00:02:00
Get drive speed succeeded.
The drive CDR speeds are: 4.
The drive CDRW speeds are: 4.

TS1363 Updated to iTunes to latest version 11.1.4.62 on my Windows 8 machine. iTunes no longer recognizes my 5th Gen Ipod. It does however recognize my 80gb Ipod Video. I've uninstalled and reinstalled iTunes as directed (twice) & rebooted pc. no luck.

I just updated iTunes to the 11.1.4.62 (as the pop up directed me to) on my Windows 8 machine. As a result iTunes will no longer recognize my 5th generation Ipod Nano (yes two). I receive a pop up saying "Ipod has been detected but could not be identified properly" I've followed the recommendations seveal times: a) disconnected and reconnected. b) rebooted computer c) unistalled and reinstalled iTunes d) tried different cables e) tried different USB porst f) rebooted Ipod.... the window keeps popping up like a middle finger (you get the point)
iTUnes WILL however, recognize my 4th gen Nano and my 80gb Video (classic) without problem
Needless to say, I'm frustrated and ticked off over all of this wasted time.
Anyone solved this issue yet?
Any good suggestions?
Please advise
Kindest regards,

c) unistalled and reinstalled iTunes
Doublechecking. Have you also tried a complete uninstall of both iTunes and all the other related software components and then a reinstall? If not, try the instructions from the following document:
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8

Windows 7 no longer recognizes my Pre

Not sure when it happened, maybe after I updated to OS 1.4.1.1, but my Windows 7 PC no longer recognizes my Pre. It used to, but now it doesn't. I have tried a cold restart for both the Pre and the laptop but still no success. Has this happened to anyone else? Any ideas from anyone?

Hello Luke and welcome to the forums;
There are several possible solutions to this issue, and we have a fairly comprehensive KB article that describes the available fixes. I recommend going through each step in order, testing for a connection after each step.
http://kb.palm.com/wps/portal/kb/common/article/25017_en.html
Hope this helps,
TreoAide

ITunes no longer recognizes my iPhone 4

I have had 3 iOS devices connecting to iTunes on Windows for more than 4 months. For some reason iTunes no longer recognizes my iPhone 4. My iPad and iPhone 4S still work as they should. Windows sees the iPhone 4, but it never shows up in iTunes. I followed the advice for getting services restarted in Windows, but since it's only one device that's an issue I'm thinking there may be an issue in the iPhone 4. Ideas?

try this, it worked for me...
http://support.apple.com/kb/TS1538

TA24326 My HP desktop running Windows Vista 32-bit no longer recognizes my iPhone 4 when I connect it. How do I correct this?

My HP desktop running Windows Vista 32-bit no longer recognizes my iPhone 4 when I connect it. How do I correct this?

Device not recognized in iTunes

MacBook Pro will no longer recognize new SSD via USB

I just received a brand-new 512 GB Samsung 840 Pro SSD from Newegg this morning.
I own a 15-inch MacBook Pro (Mid-2012) with 16 GB of RAM and a 2.3 GHz Core i7 running Mavericks (10.9.1).
Earlier today, I plugged in the SSD via a third-party USB-to-SATA adapter that I also purchased from Newegg at about the same time. The machine recognized the new drive, and I opened up Disk Utility to format the drive as Mac OS Extended (Journaled).
Once that finished, I used Carbon Copy Cloner to clone my existing HDD to the SSD. Before it began, the program asked me to create the Recovery HD, so I enabled that option. The rest of the process proceeded smoothly. I quit CCC, ejected the drive, and put it away for the rest of the workday.
When I arrived home tonight, I plugged the SSD back into the Mac in hopes of test-booting it externally. Unfortunately, the machine will no longer recognize that anything is plugged into the Mac. I find it highly unlikely that the USB adapter could be malfunctioning; I unboxed it this morning and it's been mere hours since the successful clone attempt. I also find it hard to believe that the SSD could be broken, either.
I tried to disable rEFIt and manually invoke the boot selection screen, but even when that happens, the drive fails to mount. For the same reason, I can't erase the drive to start over, either. I've tried both USB ports, as well as rebooting with the SSD connected and unconnected.
My research tells me that people often have problems trying to get SSDs to boot when they've been installed in the drive bay, but nothing I've seen suggests anyone's had a problem booting from the external SSD after a successful clone attempt. What am I missing?

I'd start by resetting the SMC. Follow the method for "a battery you should not remove yourself."
http://support.apple.com/kb/ht3964
I have no experience with Samsung SSD's, but I've read a number of posts here of people having problems with some of them. That could be a possibility.
The other thing you could try at this point is to swap the drives. If it's cloned already and the drive is good, it should boot. That would indicate the enclosure failed after the copy.

Macbook pro no longer recognizes external hard drive

Hi everyone,
My Macbook Pro (2013) running OS X 10.8.5 will no longer recognize my external hard drive.
The hard drive, a Maxtor OneTouch 4, is granted quite old (c. 5 years) but has been working fine with my Macbook pro since I bought it 2 years ago. It is too full to do time machine backups but I just need to get some files off of it. It doesn't appear in Finder or in Disk Utility when connected and turned on.
Since it's only stopped working recently I suspect some software update may have rendered it obsolete. I have also noticed some glitchiness with my USB ports, but some things work fine.
If anyone has any suggestions of what to try, I would really appreciate it! I really need to access those files.
Thanks very much in advance!

Ari343 wrote:
No, the external hard drive does not show up on Disk Utility. I don't have another computer to try it on.
Perform a PRAM reset:
http://support.apple.com/kb/ht1379
Have you tried all the ports?
Have you tried with a different cable?
Have you tested all the ports with other devices to see that they are functioning?
Ciao.

Airport no longer recognizes dsl, defaults to ehternet.

Similar Messages

Maybe you are looking for