Airport radio mode different between base station and extender

So this has basically stumped me and i decided to ask the community.  I have a Time capsule1st gen that i use as my main base station. I set the radio mode to 802"11 N 2.4ghz only. On my airport extreme 1st gen, i set it to extend the network.  However when i check the radio mode on the airport extreme  its 802.11 n b/g compatible.  Id really rather have the entire network be N only but not 5 ghz as I still have devices that don't support the 5 ghz signal (ps4)

However when i check the radio mode on the airport extreme  its 802.11 n b/g compatible
Apple gives you only one option...theirs....when you extend a network using wireless.
If you can connect the Time Capsule and AirPort Extreme using a permanent wired Ethernet connection, you will regain the 50% speed loss that was imposed by the wireless connection between devices....and....you will be able to set the AirPort Extreme to use 802.11n 2.4 GHz Only as well.

Similar Messages

  • HT1178 Can I just use my airport express as the primary base station and the time capsule as the network client?

    I bought a new airport time capsule 3tb to be used to save to file all my pictures. Can I use it as network client and the airport express as the
    Primary base station?

    To my opinion this looks a bit like what I'm looking for.
    At the moment I have an Imac that is wireless connected to a 2TB time capsule (TC1).
    To this time capsule I have another 2TB time capsule (TC2) connected via a upt wire connection.
    At the moment there is a backup made via time machine from the Imac to the time capsule TC1 (the second TC is not used)
    I'm not so technical so I hope you understand the configuration.
    What do I want to achieve :
    copy all my data from the Imac to TC1 so that the information can be accessed by more users.
    create an automatic backup from TC1 to TC2 (mirror or raid system) for security.
    give access to some users on the network to access TC1 to read and write data.
    TC2 only serves as backup from TC1 and no direct access is needed to this disk.
    If there is a solution, thanks for explaining it in 'IT kindergarden style' so that I can understand and use the info.
    Many thanks in advance.

  • What is differance between warehouse management and Extended warehouse mgt

    Hi,
    I want to understand what is extended warehouse management, You will do this. Whether this is extension of warehouse management , What extrac topics are covered in this module.  Please help me understand.
    Thanks.
    kumar,

    Hi Ashok,
    There are various differences between WM and EWM.
    One of the most visible and obvious thing that i observed is tracking of serial numbers at the Storage BIn is not in WM but thats now possible in EWM.
    EWM is just not a Warehouse Management Solution but it also has various other processes like Labout Management, Material Flow Systems(Warehouse Control Systems generally referred as).
    You also have an option of hosting Warehouse Management software on a decentralized system along with ERP.
    Also see the link below, it is a good one to start with
    http://www.scmfocus.com/sapplanning/2008/08/09/ewm-versus-wm/
    Regards,
    Kishore

  • I used Airport Base station and I was able to extend my network using airport express and connect my printers.  Now I am using Extreme and I can't extend the network (Express) or the printers nothing shows up.  I am using utility 6.3 and Mt Lion  What is

    I had an Aiport Base Station and extended using Airport Express, where I also connected my printers (network). Now using Airport Extreme off Mt Lion 10.8.4 and Utility 6.3.
    I can't extend the network (express) or connect my printers (USB) nor will it find my one wifi printer.
    What's up?

    For now, leave the AirPort Express powered off.
    Power off the entire network....all devices.....in any order that you want
    Wait a few minutes
    Power up the modem first, and let it run 2-3 minutes by itself
    Power up the AirPort Extreme next, and let it run a full minute
    Keep powering up devices one at a time about a minute apart until everything is powered up (leave the Express off for now)
    Open AirPort Utility and check to see if the AirPort Extreme is visible.
    If it's not, click the AirPort Utility menu at the upper left of the screen, then click About AirPort Utility. Post back with the version number of AirPort Utility that you see there....which should be AirPort Utility 5.6.1.
    Post back on your progress.

  • PS3/Airport express base station and DMZing

    I can figure out how to DMZ my PS3. Can any one help me, please.

    Apple calls DMZ "default host". To use "default host":
    Open AirPort Admin Utility, select your base station, and click Configure.
    Click Base Station Options.
    Select the “Enable Default Host at” checkbox. The default IP address is 10.0.1.253.
    Enter the same IP address on the PS3.

  • Airport utility does not support base station? Help!

    I cannot get base station light to turn green. Blinking amber. I upgraded to a new Verizon modem and since then the base station does not work. What can I do?

    Make sure the new Verizon Modem is not also a WiFi Router, if it is then that may be your issue.  If it is indeed just a Modem then your Ethernet Connection should work and your base station should be working.  You said "Airport Utility does not support base station".  Don't know what you meant by that.  Do you have an Airport Extreme, Airport Express or a Airport TC as a Base Station?  If yes, you should be able to set up your Network via Airport Utility.  If the Verizon Modem is only a Modem then unplug the power from your Airport Base Station, then unplug the Power from your Verizon Modem for at least 1-minute.  Plug the Modem back in and give it a moment or so, then make sure you do have an Ethernet cable going from your Verizon provided Modem to your WAN port on your Airport Base Station.  Now power up your Airport Base Station and go to your Airport Utility.  Find the Base Station and click on Edit...  Make sure your Network Name is correct, your Password is Correct, your Security method is correct (example:  WPA2 Personal).  If all correct see if your blinking Amber light is now Solid Green. 

  • How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

    How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

    This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
    http://support.apple.com/kb/HT4145
    In particular, you would want to focus on the information regarding a "Roaming Network"

  • Difference between AirPort Extreme base station and airport express

    What is the difference between AirPort Extreme base station and airport express

    Please see this Apple comparision document for details.  Post back on any specific questions including your specific requirements.
    http://www.apple.com/compare-wifi-models/

  • Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

    I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
    The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
    Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
    Thanks

    The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
    If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
    So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
    Assuming your AE is gen3 or greater.
    You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
    And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
    If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
    If your AE is G wireless or earlier model.. really the time has come for replacement.
    If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
    You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

  • Connecting Airport Extreme Base Station and HiTron CGN3

    A recent installation of Internet/CableTV services by Rogers.ca replaced my Airport Extreme Base Station WiFi network with one based on the Hitron CGN3 Cable Modem/Router.  Many of the WiFi enabled evices in the home were switched to the new network without too much hassle. However, my multiple NEST CO/Fire alarms failed to connect and after some hunting I established that the CGN3, although apparently ipv6 'compatible' has this protocol not enabled.  There is no input facility in the modem setup to activate the protocol.  The importer of the device seems to have chosen to not respond to such tech issues.
    It now comes down to either using the CGN3 as a Modem/WiFi server or extending the network to include the Airport Extreme on the CGN3 (don't know how to do that) or vice versa, extending the Airport network to include the CGN3 (don't know how either). 
    QUESTION:
    Does anyone have any idea on how to make the Airport Extreme and HiTron Modem/Router function together since the Extreme has the ipv6 protocol enabled and NEST (and other 'Internet of Things') devices will reconnect, no problem.
    More Info:
    The only reason for the CGN3 to remain as a WiFi server is its range which seems to cover the required service area with a more powerful, stable signal than the Airport.  That is somewhat important since TV services come over the Internet and mobile devices apps available from the Apple store can be used as very capable program guides/selectors and remotes for the HDPVR and secondary HD boxes that feed the TVs, eliminating a remotes collection and associated programming and infra-red transmission hassles.  I believe the Cable boxes would accept getting the TV signals from the CGN3 and function commands from the Airport Extreme networks. That remains to be proven.  Level 2 Technicians at Rogers and NEST Labs have looked at this and can't access the CGN3's ipv6 function to activate it.  They don't know much about the Airport Express.
    Second Thought:
    On the other hand, a second apple Airport base station would extend the network range to rival the CGN3 and the WiFi function of the CGN3 could be turned off.  I tried to connect the two routers by LAN cable but they don't seem to see each other and I don't know enough about network settings to get any further. 

    Whichever airport you use.. express or extreme doesn't matter much..
    It should be setup in bridge mode. Plug an ethernet cable from LAN port on the CGN3 to WAN port on the Apple router.
    Go into the airport utility and run through the setup. Don't be too worried if it chooses the wrong setup.. you can go back and edit it after the setup is complete.
    You will want to open the Edit.
    Then go to the various tabs to ensure it is setup the way you want..
    On the Network tab.. bridge mode.
    On the wireless tab, create a wireless network.
    I recommend you use names that are short, no spaces and pure alphanumeric. eg AEwifi In my case with Time Capsule I use separate wireless names for the two bands. TC24ghz and TC5ghz but that is up to you.. it can make life easier.. then set channels can also make things easier.
    Ensure your IPv6 is setup correctly.
    The actual internet option will be dhcp.
    You will have two wireless networks.. but both will use the CGN3 as router.. the airport if it worked in the past should work. Even if it is not the dhcp server. BUT let me add there is another way to fix this if this setup doesn't work.. please post back your result.. no luck then I will show you how to setup a static IP with the Apple router.

  • Airport Extreme Base Station and xBox wireless

    We have 2 macs with Airport Extreme Base Station connecting to Cable modem for internet connection.
    Recently bought an xBox with a USB wireless adaptor. When xBox is connected to the wireless network, internet connection of other computers dropped out and no longer can use internet until xBox is disconnected from the wireless network. It is the same problem even other computers are connected to Base Station with Ethernet cable.
    Any settings in Airport Utility might fix this problem ?

    We didn't have any problem before using the xBox wireless.
    There are 2 Macs (iMac 20" & Macbook Pro 15") and they're connected to the Base Station via wireless.
    The cable modem is Motorola Surfboard SB5100i and there is no login required from ISP for internet connection. Yes, the modem is connected to the WAN port of the Base Station.
    With the Clients computer network settings, we are using DHCP. We have also tried with static IP and didn't make any differences.
    I thought it could be the compatibility issue between the xBox wireless adaptor and the Base Station and on the other hand, the wireless protocols (802.11N/g/b) are industry standard and it doesn't matter who made them, they should work together.
    The only idea that I have now is to try with other brand of wireless router and it might be a quick solution for this problem.
    thanks,
    David

  • Vonage, AirPort Extreme Base Station, and Comcast

    I just picked up an Airport Extreme Base Station, and wanted to use it to get my MacBook Pro on my home network. However, I can't get it to actually provide an network connection to the MacBook. In the Network pane of System Preferences, under the Network Status, AirPort has a yellow icon, and the following message: "AirPort is connected to the network HulkNet. AirPort has a self-assigned IP address and may not be able to connect to the Internet."
    Here's my current setup:
    Comcast > Cable Modem > LinkSys RTP300 > PowerMac, PC, AEBS
    I have the "Distribute IP addresses" disabled on the AirPort, and the internet for the PowerMac & the PC work fine. In the network status of the RTP300, the AEBS is listed as having an IP address of it's own.
    Any gurus out there that can help me figure this out? I just want to be able to access my home network from anywhere in the house!

    All,
    I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
    I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
    My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
    The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
    I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes?

  • Using both Airport Extreme Base Station and Airport Express

    I am using a Airport Extreme and a AX, my goal is to use the base unit on one floor of the home and they AX as an extender.
    I have linked the AX unit to join the existing network, now how to do I enable WEP 128 bit?

    Here are the WDS setup steps...
    AEBSn - WDS Setup
    (Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete.)
    Main Base Station Setup (AEBSn)
    o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
    o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
    o Select the main base station, and choose Manual Setup from the Base
    Station menu, or double-click the base station to open the configuration in a separate window.
    o Enter the base station password if necessary. If the base station is using the default password of public, you will not be prompted for a password.
    o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
    o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
    o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
    o Click the Add "+" button and enter the MAC address of the base stations you want to connect to this base station.
    o Click Update to send the new settings to the base stations in the WDS.
    Remote Base Station Setup (AX)
    o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
    o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
    o Select the remote base station, and choose Manual Setup from the Base Station menu.
    o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
    o Enter the same network password as the main base station, if necessary.
    o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
    o Click WDS and choose “WDS remote” from the pop-up menu.
    o Enter the MAC address of the main base station in the WDS Main field. The MAC address is also referred to as the AirPort ID and is printed on the label on the bottom of the base station.
    o Click Update to transfer the settings to the base station.
    (ref: Pages 41-45 of "Designing AirPort Extreme 802.11n Networks.

  • Since latest update to airport extreme im getting 10 unknown base station and time capsule items showing in airport utility as a network.  when able to "forget" them they initially drop off but soon return. how do i get them deleted and stay that way

    since latest update to airport extreme im getting 10 unknown base stations and time caps showing up as though they are a part of my network. sometimes i can "forget" them and they will disappear initially but soon return. i need and want only my connection inside my home . any ideas. i have done a factory reset and set up a new network but they continue to show up.

    I'm not convinced that the problem lies in Airport Utility. This same thing was happening to me, nearly exactly as you describe it. The thing is that with me, the problems clearly started when I updated the firmware in my Airport Express (n). That's when all the wacky stuff started happening. Sometimes it would show up in AU, sometimes it didn't and even if it didn't, I could still access the internet through it.
    But as you said, the problems got really bad when another Express (b/g) was put on the network with it. Even when it did work, the (b/g) would make it impossibly slow.
    You know more about this than me, and clearly have more patience if you've restarted the network fifty times. I gave up at about ten.
    In any case, your solution is more of a work around and if you're still having that slow connection problem, I'm not sure you've got it. But thanks for your reporting of this. At least I know I'm not crazy.

  • I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

    I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

    Which version of the AirPort Utility are you using?

Maybe you are looking for