Airport-Router authentication issue

Hi - I have a really annoying authentication issue between my MBP (late '06) and my DIR-655 D-Link router (f/w 1.22 b05).
I am getting "disconnection" issues on my MacBook Pro only. We are not seeing any issues on my fiance's Vaio laptop. So I'm thinking maybe the router isn't to blame...?
I put "disonnection" in quotes because airport always shows that there is a connection to the router/network, but there clearly is not. Sometimes I have to disconnect/reconnect airport, but often the connection just comes back after 30 seconds or so. It usually looks like a DNS issue...holding at the "looking up" stage, but I really don't think it is. I've tried various domain name servers.
I thought I had worked around this by allowing the router to accept G in addition to 802.11n connections, but the problem, while not as prevalent, seems to have increased lately even while using 802.11g.
I see that the router's log is replete with messages like this:
*Wireless system with MAC address 0017F2HR7BC6 disconnected for reason: Authentication Failed*
That MAC address is indeed my MBP
I'm also seeing a lot of messages along these lines:
*Blocked incoming TCP connection request from 119.154.75.13:1420 to 173.78.73.92:445*
But I assume these messages are unrelated.
So I turned off WPA-Personal security and, of course, no further authentication errors. Those blocked TCP requests continue.
Of course, I don't want to keep WPA turned off.
Any ideas as to why authentication would be failing on and off with airport? I didn't even realize there was more than a single authentication (i.e. after you first connect), but I still have a LOT to learn about routers!
Any ideas appreciated!

FWIW
119.154.75.13 = an address in Pakistan
173.78.73.92 = an address in Tampa, Florida on the Verizon Network
Have you been using BitTorrent or some other p2p software lately ?
Re your router issue, have you considered using MAC Address Security (not WAP/WEP) ?

Similar Messages

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

I recently replaced my dead airport router with a netgear91-5g router and synced it successfully to my Lexmark Pro 915 printer and my computer and yet when I try to print wirelessly I get the message: "printer not connected; printer offline".

I recently replaced my dead airport router with a Netgear91-5g router and synced it successfully to my Lexmark Pro 915 printer and my computer; yet when I try to print wirelessly I get the message: "printer not connected; printer offline". Lexmark support verified that my printer was connected to the new router and the problem was with the computer's printer configuration and they could reconfigure it online if I paid for their "Premium Support" services ($119 for one year, 3 fixes). I declined, feeling sure that this is something I could do if I knew how. Could it be an incompatability issue with OS 10.8.3?

You saved me $$$ that I can ill afford on my fixed income. I was very unhappy with the "support" from Lexmark... what a rip off! Thank you dwb!

Yoga 2 11 drops signal on Airport router - change router settings?

i have spent several hours with Lenovo tech supports (all perfectly friendly), trying to fix the issue of the Yoga 2 11 consistently dropping the wifi connection at my workplace. Two important considerations:
* It's not entirely on the Yoga, as it does not have this issue with home wifi, coffee shop wifi, etc.
* And several other PC and Mac desktop and laptops have no trouble with the workplace wifi. The problem is definitely the way that the Yoga interacts with the Airport router.
Lenovo tech support has made numerous changes to my drivers, system settings, and so on, but cannot fix the problem. The next solution is to return the Yoga to factory settings -- a solution I'm convinced will not work as I've already returned one laptop to Best Buy for the same problem. In other words, two Yogas, directly out of the box (presumably with factory settings), had this issue.
My question is -- is there possibly a way I can change the Airport router settings (or set up a new network entirely) that might be more compatible with the Yoga 2 11 with Intel Wireless-N 7260 card? If I can't get the Yoga to talk to the router, maybe the router can be changed to talk to the Yoga.

Which model AirPort Base Station do you have?
To determine that open AirPort Utility, select your base station, then position your cursor over the base station's name. Reply with the text shown adjacent to "model".

Authentication issues

We've had authentication issues with Infinity since the install just over a week ago (BT Business package)
The router will drop the connection and then we have a problem reconnecting (won't). Out of sheer frustration I've discovered a workaround that sometimes works that is to change the user name to the BT test account, connect, and then change the router user name setting back to our own. The BT test account always works, so despite a BT engineer being sent to trace the problem onsite yesterday the issue remains. We've also been sent a new router, and the BT engineer arrived with yet another new one yesterday
The problem seems to be purely authentication. The Technical Helpdesk have changed our password (twice) but we still get the problem. Yesterday I was told that some other users in our area have also had an authentication issue and that over the weekend 'patches' were going to be applied at our local exchange.
When the service works we get quite good speeds (37 down, 8 up) but we're frustrated with the lack of knowledge from the help-desk and have doubts that the 'patches' will resolve the issue
Such is the problem that BT will downgrade us back to ADSL2 (which was rock solid in comparison) next week if we're still unhappy
I did ask if our user name could be changed but told no. I'm curious to know as to what the switch to fibre could cause authentication problems?

hi this is a BT Residential forum as a Business user you may get more help from the BT business forum
http://business.forums.bt.com/t5/Broadband-and-internet/bd-p/Broadband
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Provide steps to connect HPLJ P1102w to AirPort router (MacOSX 10.5.8)

Please provide deterministic set of steps for connecting HP LJ P1102w wirelessly to AirPort router (MacOSX 10.5.8).
I recently bought a HP LaserJet P1102w in the hopes that since it supports AirPrint and my OS, I should be able to quickly and easily connect it to my wireless network, which has been running without any hitches, except the occasional rebooting of the router. I've tried everyhing, including reading the quick start guide and the on-CD manual that came with the printer (two things that as a convert from PCs to Macs several years back, I have learned shouldn't really even be necessary, when things just work out of the box.)
I have gone through the standard install on the SW CD, gone through the steps to upgrade fhe firmware, and tried various combinations of the steps indicated in the conflicting suggestions I found in the quick start, CD user manual, and in the online support site that HP has set up in lieu of actual human support. At one point, through some combination of (not all documented) steps that I can not reproduce, I managed to get to a web-based configueation page on the printer, and successfully provided my net SSID and password, and confirmed by having the printer produce it's configuration page that it did have the settings to connect to my wireless network. However, the IP address it was reporting was still a standard "local" IP address (starting with 169.xx.xx.xx), rather than being on the correct subnet for my actual network (10.xx.xx.xx). And I could no longer get to the printers web-based config page (no matter what IP I tried in my browser) to check/adjust settings.
i found in another location the suggestion to go through the System Preferences to get to the Print Queue, and select Utiltiy --> HTMLConfig..., which I also tried tonight, but as soon as I click the HTMLConfig... button, the Utility simply closes and nothing else happens.
I'm on the verge of returning the printer if I can't get it configured correctly. As it is, I'm very displeased that I've had to spend this much time trying to get set up (and it's still not working). I used to build computers from scratch back in the day-- but that was "for the fun" of trying to get all the pieces to work together, correct drivers installed, etc. -- but I thought we were far beyond that for end-user products that are intended to work out of the box. And I'm surprised at the lack of quality / consistency in the documentation provided by HP.
Any help other users (or hopefully HP!) can provide would be appreciated, *particularly* it it's in the form of "reset to facory settings by pressing these buttons, and perform these steps to ensure a successful installation."
Thanks.

Carolyn Samit wrote:
HI Samuel,
Definitely try a different channel.
Airport Troubleshooting Guide
Carolyn
Hey Carolyn thank's for your reply!
The Airport Troubleshooting Guide is great. Unfortunately did not help in my case.
(I tried a lot of other things, too. Installing the combo update 10.5.8, resetting PRAM, deleting keychain entries, removing Aiport adapter in the list of network adaptors, removing known networks and so one. Nothing did a change!)
What did help indeed was to plug in the Mac by ethernet cable and configure the Airport Express base station to a different channel. Then it works like charm (again), as you suggested, too.
I tested with another (d-link) wlan (b/g) station and confirmed my first suspicion that it has something to do with the channel and not with the base station or some configuration.
Both, channel 12 and 13 are NOT working, but all others do fine!
This is a bug (introduced in 10.5.8 or maybe 10.5.7, I am not sure?). I repeat, this is a bug and unrelated to the wifi battery issues described by others. I guess I will file a feedback report.
As a work-around, switch to another channel. I am not sure what happens to people who have channel left to "automatic" and the base station changes to 12 or 13 by itself. (Is this technically possible?) I think they will get problems. Definetely.
For completeness, my specs:
Model Name: MacBook Pro 15"
Model Identifier: MacBookPro1,1
Processor Name: Intel Core Duo
Processor Speed: 2 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 2 MB
Memory: 2 GB
Bus Speed: 667 MHz
Boot ROM Version: MBP11.0055.B08
SMC Version (system): 1.2f10
AirPort Card Information:
Wireless Card Type: AirPort Extreme (0x168C, 0x86)
Wireless Card Locale: Worldwide
Wireless Card Firmware Version: 1.4.16.2
Current Wireless Network: Apple Airport Express
Wireless Channel: 1

Airport router needs to have a settings check because videos keep freezing up. How to do

Hi, my airport router settings are not correct. I can not play any kind of online videos without them freezing up. What do I do? what settings need to be changed and how?

It appears that you currently do not have enough bandwidth to play these videos. Was this working before and the streaming issue just started or have you never been able to get videos from the Internet successfully?
What is the model of your AirPort base station? Does it connect directly to a broadband Internet modem or to another router? How are you trying to play these streams: Apple TV, Mac or PC, or to an Internet-ready HDTV?

HT4995 My iPad 2 Location Service works fine but does not work on my home Airport router. How can I fix the problem?

My iPad 2 Location Service works fine but does not work on my home Airport router. How can I fix the problem?

lbryan1987 wrote:
I dont want the button problem solved i need to know how to restore the phone without using that button or going into settings
You don't in the condition it's in. You will either have to get the phone replaced by Apple or pay a 3rd party to repair it.
there seriously should be more than two ways to solve this other wise apple is useless and we will never buy another apple product.
Seriously? It's physically broken!

External backup drive connected to airport router giving "... backup disk image ... /.../... is already in use" error.

I just added an external backup drive to my airport router for my desktop and my laptop to use. Initial backups worked, but now I'm getting "... backup disk image ... /.../...MacBook Pro.sparcsbundle is already in use." This message is on laptop even after stopping timemachine on the desktop. The initial backup worked for both machines. Is this a timing problem? It shows the last backup happened earlier this evening, but I'm concerned about the major amount of work I did after that time.
Thanks in advance for any help you can offer!

You can't use that configuration for Time Machine backups, if that's what you're doing.
Mac 101: Time Machine

Authentication issue getting "UMELoginException"

Dear Guys,
I am facing an authentication issue. The situation is like this,
My NT password was about to expire (had 6 more days for expiry). I was able to login till yesterday and all of the sudden today, when I was trying to login, I was not able to (it gave me password change message). So I went back and changed my NT password and tried to login again into the portal, however I am still not able to. I am pasting the stack trace,
#1.5#001143FDCEA7006700000008000018C40004196E4AD849E8#1153861399615#com.sap.security.core.imp#sap.com/irj#com.sap.security.core.imp.[cf=com.sap.security.core.sapmimp.logon.SAPMLogonLogic][md=doLogon][cl=20282]#Guest#192####fff21cf01c2011dba425001143fdcea7#SAPEngine_Application_Thread[impl:3]_0##0#0#Error##Java###doLogon failed
[EXCEPTION]
#1#com.sap.security.core.logon.imp.UMELoginException
     at com.sap.security.core.logon.imp.SAPJ2EEAuthenticator.logon(SAPJ2EEAuthenticator.java:318)
     at com.sapportals.portal.prt.service.authenticationservice.AuthenticationService.login(AuthenticationService.java:344)
     at com.sapportals.portal.prt.connection.UMHandler.handleUM(UMHandler.java:126)
     at com.sapportals.portal.prt.connection.ServletConnection.handleRequest(ServletConnection.java:186)
     at com.sapportals.portal.prt.dispatcher.Dispatcher$doService.run(Dispatcher.java:522)
     at java.security.AccessController.doPrivileged(Native Method)
     at com.sapportals.portal.prt.dispatcher.Dispatcher.service(Dispatcher.java:405)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at com.sap.engine.services.servlets_jsp.server.servlet.InvokerServlet.service(InvokerServlet.java:156)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.doWork(RequestDispatcherImpl.java:312)
     at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:368)
     at com.sap.portal.navigation.Gateway.service(Gateway.java:101)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:390)
     at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:264)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:347)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:325)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:887)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:241)
     at com.sap.engine.services.httpserver.server.Client.handle(Client.java:92)
     at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:148)
     at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
     at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
     at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
     at java.security.AccessController.doPrivileged(Native Method)
     at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)
     at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)
Please help.
Regards,
Deepak

Hi Deepak,
it is most times that it needs to replicate through your system(s).
Regards,
Kai
PS: Please reward points if that was helpful.

Authentication Issue, When Profile ReCreate

Hi,
i face authentication issue in SQL Server 2012 Evalution after i login in new account.
Take a look situation and what i did.
1) I install SQL Server 2012 in Member Server (Server 2012 Standard).
2). Every Thing i Did i by using AD User name "SP_Farm"
3). I install SQL in Windows Authentication Mode only and i provide User ****\SP_Farm, when Ever Installation Ask.
Note: during the whole process i only use SP_Farm (AD Admin User)
Every thing going working fine till my mistake. By mistake i delete account SP_Farm from AD and i re create it.
after that i cant access Management Studio. :(
Please Guide if is there any other way.
Thanks you
Shariq Ayaz
[email protected]
www.shariqdon.com
www.shariqdon.com/itworld
www.shariqdon.com

Hi,
i face authentication issue in SQL Server 2012 Evalution after i login in new account.
Take a look situation and what i did.
1) I install SQL Server 2012 in Member Server (Server 2012 Standard).
2). Every Thing i Did i by using AD User name "SP_Farm"
3). I install SQL in Windows Authentication Mode only and i provide User ****\SP_Farm, when Ever Installation Ask.
Note: during the whole process i only use SP_Farm (AD Admin User)
Every thing going working fine till my mistake. By mistake i delete account SP_Farm from AD and i re create it.
Creating a user with the same name is
not the same user :-)
A user has a unique ID and you did not create the same ID, but a new user with same name.
after that i cant access Management Studio. :(
Please Guide if is there any other way.
Thanks you
Shariq Ayaz
[email protected]
www.shariqdon.com
www.shariqdon.com/itworld
www.shariqdon.com
You can try to use This solution:
http://blogs.msdn.com/b/raulga/archive/2007/07/12/disaster-recovery-what-to-do-when-the-sa-account-password-is-lost-in-sql-server-2005.aspx
* After the SQL Server Instance starts in single-user mode, the Windows Administrator account is able to connect to SQL Server using the sqlcmd utility using Windows authentication.
[Personal Site] [Blog] [Facebook]

Essbase 6.5 External Authentication Issue!! Urgent Please!!

Hi all,
I am great trouble over an external authentication issue in Essbase 6.5. I request you all to please give me your feedback on the same as soon as possible.
I am in a situation where I need to get my Essbase 6.5 external Authentication converted from LDAP to Active Directory services.
I suppose there has been necessary changes done to the .cfg file for the same. However, I think I am getting an error
"User [vikc]'c external authentication protocol [MSEX]'s password check module is not loaded".
Please let me know if you have come across such an issue earlier and can anybody to able to help me with the same.
Its kinda Urgent. so any replies for the same will be appreciated.
Thanks and Regards,
Vikram

Vikram,
Yes you will have to reconfigure the CSS.xml and cfg file for external auth.
Here is the Sample CSS
<spi>
          <provider>
               <msad name="full360">
                    <trusted>false</trusted>
                    <url>ldap://192.168.1.100:389/DC=full360,DC=com</url>
                    <userDN>CN=Ravinder Singh,DC=full360,DC=com</userDN>
                    <password>full@360</password>
                    <authType>simple</authType>
                    <identityAttribute>dn</identityAttribute>
                    <maxSize>1000</maxSize>
                    <user>
                         <loginAttribute>sAMAccountName</loginAttribute>
                         <nameAttribute>dn</nameAttribute>
                    </user>
                    <group>
                         <nameAttribute>cn</nameAttribute>
                         <objectclass>
                              <entry>group?member</entry>
                         </objectclass>
                    </group>
               </msad>
Download this toll "http://www.ldapbrowser.com/download.htm"
LDAP browser to get the perfact DN information.
Let me know the status
Ravikant

HT1331 I just bought a airport wireless router I have a time warner cable modem. I have hook up the modem correctly to my new apple airport router and my modem is not working with the apple airport router. what do i need to do?

I just bought a airport wireless route and I have a time warner modem. My problem is my modem is not connecting to my apple airport router. What do I need to do?

Power cycle the cable modem.. you may try leaving it off 5min.. might be enough.. sometimes you need 15min or even longer.. Followed by power cycle of the AE.
Nothing else should be connected to the modem.. except the router that will get the public IP as they only hand out ONE>

ACS 5.2 Authentication Issue with Local & Global ADs

Hi I am facing authentication issue with ACS 5.2. Below is AAA flow (EAP-TLS),
- Wireless Users >> Cisco WLC >> ADs <-- everything OK
- Wireless Users >> Cisco WLC >> ACS 5.2 >> ADs <-- problem
Last time I tested with ACS, it worked but didn't do migration as there'll be changes from ADs.
Now my customer wants ACS migration by creating new Group in AD, I also update ACS config.
For the user from the old group, authentication is ok.
For the user from the new group, authentication fails. With subject not found error, showing the user is from the old group.
Seems like ACS is querying from old records (own cache or database). Already restared the ACS but still the same error.
Can anyone advice to troubleshoot the issue?
Note: My customer can only access their local ADs (trusted by Global ADs). Local ADs & ACS are in the same network, ACS should go to local AD first.
How can we check or make sure it?
Thanks ahead,
Ye

Hello,
There is an enhacement request open already:
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCte92062
ACS should be able to query only desired DCs
Symptom:
Currently on 5.0 and 5.1, the ACS queries the DNS with the domain, in order to get a list of all the DCs in the domain and then tries to communicate with all of them.If the connection to even one DC fails, then the ACS connection to the domain is declared as failed.A lot of customers are asking for a change on this behavior.
It should be possible to define which DCs to contact and/or make ACS to interpret DNS Resource Records Registered by the Active Directory Domain Controller to facilitate the location of domain controllers. Active Directory uses service locator, or SRV, records. An SRV record is a new type of DNS record described in RFC 2782, and is used to identify services located on a Transmission Control Protocol/Internet Protocol (TCP/IP) network.
Conditions:
Domain with multiple DCs were some are not accessible from the ACS due to security/geographic constraints.
Workaround:
Make sure ALL DCs are UP and reachable from the ACS.
At the moment, we cannot determine which Domain Controller on the AD the ACS will contact. The enhacement request will include a feature on which we can specify the appropriate the Domain Controllers the ACS should contact on a AD Domain.
Hope this clarifies it.
Regards.

Wireless Client Authentication issues when roaming Access Points (Local)

I have a Cisco 5508 with Software version 7.4.121.0 and Field Recovery 7.6.101.1.
There are a handful of clients that when roaming between AP's with the same SSID that get an authentication issue and have to restart the wireless to get back on.
From Cisco ISE
Event
5400 Authentication failed
Failure Reason
11514 Unexpectedly received empty TLS message; treating as a rejection by the client
Resolution
Ensure that the client's supplicant does not have any known compatibility issues and that it is properly configured. Also ensure that the ISE server certificate is trusted by the client, by configuring the supplicant with the CA certificate that signed the ISE server certificate. It is strongly recommended to not disable the server certificate validation on the client!
Root cause
While trying to negotiate a TLS handshake with the client, ISE expected to receive a non-empty TLS message or TLS alert message, but instead received an empty TLS message. This could be due to an inconformity in the implementation of the protocol between ISE and the supplicant. For example, it is a known issue that the XP supplicant sends an empty TLS message instead of a non-empty TLS alert message. It might also involve the supplicant not trusting the ISE server certificate for some reason. ISE treated the unexpected message as a sign that the client rejected the tunnel establishment.
I am having a hard time figuring out what is causing this. My assumption is if there were a problem with the Controller or AP configurations then it would happen to everyone. My further assumption is if the client had a problem with their laptop (windows 7) then why does work at other times? So I have checked and the ISE certificate is trusted by client.
Is something happening that the previous access point is holding on to the mac and the return authentication traffic is going to the old AP instead of the new one or something like that which is corrupting the data?
I also had this from Splunk for the same client:
Mar 5 13:44:51 usstlz-piseps01 CISE_Failed_Attempts 0014809622 1 0 2015-03-05 13:44:51.952 +00:00 0865003824 5435 NOTICE RADIUS: NAS conducted several failed authentications of the same scenario
FailureReason="12929 NAS sends RADIUS accounting update messages too frequently"
Any help on this would be appreciated. These error messages give me an idea but doesn't give me the exact answer to why the problem occurred and what needs to be done to fix it.
Thanks

Further detail From ISE for the failure:
11001
Received RADIUS Access-Request
11017
RADIUS created a new session
15049
Evaluating Policy Group
15008
Evaluating Service Selection Policy
15048
Queried PIP
15048
Queried PIP
15004
Matched rule
15048
Queried PIP
15048
Queried PIP
15004
Matched rule
11507
Extracted EAP-Response/Identity
12500
Prepared EAP-Request proposing EAP-TLS with challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12301
Extracted EAP-Response/NAK requesting to use PEAP instead
12300
Prepared EAP-Request proposing PEAP with challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12302
Extracted EAP-Response containing PEAP challenge-response and accepting PEAP as negotiated
12318
Successfully negotiated PEAP version 0
12800
Extracted first TLS record; TLS handshake started
12805
Extracted TLS ClientHello message
12806
Prepared TLS ServerHello message
12807
Prepared TLS Certificate message
12810
Prepared TLS ServerDone message
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
11514
Unexpectedly received empty TLS message; treating as a rejection by the client
12512
Treat the unexpected TLS acknowledge message as a rejection from the client
11504
Prepared EAP-Failure
11003
Returned RADIUS Access-Reject

Airport-Router authentication issue

Similar Messages

Maybe you are looking for