Airport Time Capsule cannot see my existing wireless network

Just bought iMac and an ATC, and have the iMac connected to my wireless network (Linksys WRT1900AC, 802.11ac) and trying to get the ATC to see it and extend it.  The ATC light is blinking amber and while I can see it in the airport utility, when I try to get it to join my wireless network--it doesn't see it, only sees one (my iMac sees 6) and it's my neighbor's (who has a Mac, not sure if Apple wireless)
What to do?
Thanks!

The Time Capsule cannot wirelessly "extend" the signal from the Linksys wireless router.
Instead, the Time Capsule needs to connect to the Linksys router using a permanent, wired Ethernet cable connection.
If you want the Time Capsule to provide additional wireless coverage, it can do so. Simply use the same wireless network name and password as the Linksys network.
Here, I am assuming that the Time Capsule will be located a few rooms away from the Linksys router....and not in close proximity to the Linksys router.

Similar Messages

  • Force time capsule to connect to existing wireless network at 5GHz speed?

    I've just bought the dual band 2TB time capsule to be added to my current network as a wireless backup device. It's connected to my existing network just fine, on my 5GHz network (I run both a 5GHz and a 2GHz network, for laptops and iphones respectively).
    However when I go into my router and look at the attached devices, the MAC address of the time capsule that appears is that of it's 2.4GHz network. Does this mean that it's actually connecting to my network as an 'a/b/g' device rather than an 'n' device? And if this is the case, how do I force it to connect as an 'n' device?

    Bob thanks for the reply.
    The Time Capsule is in the same room, about a metre and a half away from the router at present (as I've not figured out where I actually want to put it yet).
    Also it is connected to the 5Ghz network (as the networks have different SSIDs), it's just that the MAC address that appears in my routers 'attached devices' screen for the Time Capsule is the same as the MAC address of the time capsules 2.4GHz network when I start up the Aiport Utility.
    I guess what I'm trying to get to the bottom of is if this is normal and in actual fact it's connecting at 5GHz, but that the Time Capsule's MAC address, when used as a normal device connecting to a network, is the same as it's 2.4GHz network MAC address (if that makes sense).

  • Have a 802.11n time capsule, the range of the wireless network has shrunk down to nothing over last few days. Used to be able to use wireless network anywhere in house, but now can only use in my office. Will not connect to iphones, ipad, itouch, or noteb

    Have a 802.11n time capsule, the range of the wireless network has shrunk down to nothing over last few days. Used to be able to use wireless network anywhere in house, but now can only use in my office. Will not connect to iphones, ipad, itouch, or notebook. Worked fine last week, but over weekend just started having issues.

    It is very possible that you may have some form of Wi-Fi interference that has appeared recently that is preventing your Time Capsule (TC) from providing a clean RF signal.
    I suggest you perform a simple site survey, using utilities like iStumbler, or AirRadar to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible. Look for other Wi-Fis that may be operating nearby. Note those with the strongest signals and which channels they are operating on ... then change the channel used by the TC to be at least 3-5 channels away.

  • Using airport time capsule to create an internet connected network from pre existing wifi network

    i bought an airport time capsule for college. I bought it to create a network for my dorm room so that I could take the pre existing wifi from the school and make my own mini network that I can hook my other stuff up to. Problem is that I don't have an ethernet hook up in my room so the network would have to be created from a wifi network rather that a ethernet hook up. Is this still possible? Alternate suggestions? I am afraid of either the college network blocking users from communication with other devices via the wifi, or the fact that my printer would be on a huge network for all to screw with.

    Is this still possible?
    NO, it won't work. Apple only works with apple.
    Alternate suggestions?
    I am sure your college has rules about not running your own wifi networks.. but anyway.. that is up to you.. the Apple TC cannot turn off 2.4ghz which would be handy.. so the only way to do this following the rules is ethernet. You can run a full network standalone on ethernet. And still use wireless for internet.
    If you want to use wireless standalone this is also possible but you need to connect a second wifi USB dongle your Mac so you can have two networks at once.. You can use an express to connect to the college wireless and bridge that to the TC by ethernet.. then use the TC to create your own network.. since you cannot turn off 2.4ghz I guess how long the College IT people take to track you down should be hours. If you could just use 5ghz it would probably be ok.

  • Airport Time Capsule as Hard Drive and Wireless Router

    Hello,
    My girlfriend and I want to buy Macbooks. A Macbook Pro 128 GB and a Macbook Air 128 GB. 128GB each is not enough for our needs and are also interested in buying an Airport Time Capsule with 2 TB rather than upgrading to 256GB/512GB, which is more money for less storage space.
    My question is, can we use the Airport Time Capsule as a wireless router AND as a wireless hard drive?
    Will I be able to keep the Time Capsule at home working as a wireless router for my girlfriend to surf the web and at the same, if I am at the library, as a wireless hard drive via internet so I can download the files i need?
    If the network is down I would like to be able to use it via cable as a wired hard drive. Is that possible?
    I searched for days for an answer but I could not find a definitive answer to my question.
    Thank you!
    Best regards,
    Liviu

    My question is, can we use the Airport Time Capsule as a wireless router AND as a wireless hard drive?
    Yes. The Time Capsule has a built-in hard drive and you can add additional USB hard drives (via a USB hub) to its USB port. All of these drives can be shared out and will appear in the Finder as network drives.
    Will I be able to keep the Time Capsule at home working as a wireless router for my girlfriend to surf the web and at the same, if I am at the library, as a wireless hard drive via internet so I can download the files i need?
    Yes, that is also possible. Please check out the following AirPort User tip for more details on how this can be set up.
    If the network is down I would like to be able to use it via cable as a wired hard drive. Is that possible?
    If you mean if the wireless network is down can you still access the Time Capsule's hard drive via an Ethernet connection, then the answer is yes.

  • HT3728 I am trying to use my airport time capsule as an extender on my network, but I can't find it anywhere now.  Tried a reset, but device is lost.

    I set up a new network with a new AirPort Extreme station.  I was able to reset all of my old devices, Airport Express, etc., by I haven't been able to get my time capsule to attach to the new network.  It just doesn't show up anywhere. 

    Ultimately I am using it as an extender itself.
    Thanks, but I'm not sure that you understand that an extender can function using a network Ethernet wired connection or a wireless connection.
    So, we asked for clarification on what you wanted to do in our previous post. We asked......
    Will the Time Capsule "extend" by connecting using an Ethernet cable to the AirPort Extreme?
    Or, are you hoping to have the Time Capsule "extend" the signal wirelessly?
    We also asked.....
    Are you still using OS X 10.6 as your profile indicates? If not, what is the operating system you are using?
    We have a Time Capsule, have seen this issue, and know how to fix it. So we can likely help, but we cannot see your network, or know your thoughts, so we must ask for your assistance.
    It is possible that you are not comfortable providing the information that we requested. We understand. In that case, please wait for another person to respond to your question.

  • Can my older Airport Express 802.11g join an existing wireless network

    I have a Airport Express 802.11g firmware version 6.3 . Using the most recent Airport Express Utility I can set it up as a base station on its own independent network but I cannot join it to my existing home wireless network. As I go through the wizard (or manual setup) It just does not detect/display any existing wireless networks. I have plenty of mobile devices in the  house that can see the wireless network...and next doors network.
    So, it begs the question ... is an 802.11g unit actually capable of joining another network or is this capability available on later models only. A search of apple support and the wider internet for "Airport Express 802.11g capabilities" yeilds a blizzard or useless info.
    Thank you

    Sorry, I cannot help on Windows since I do not have a Windows 7 machine here to test. I have used XP in the past and AirPort Utility appears to be virtually the same in Windows as a Mac. I assume that this is the case for AirPort Utility 5.6.1, and it should be able to configure the Express.
    The older Express will join most wireless networks if the following conditions are met:
    1) The Express is functioning correctly.
    2)  The wireless network name is 12 characters or less and it contains only normal letters and numbers. Avoiding blank spaces in the wireless network name will help improve the chances of the Express joining the network as well.
    3)  The wireless router is broadcasting a compatible signal that would allow the "g" Express to connect. If your network is broadcasting a wireless "n only" signal, the Express cannot connect to this network.
    4)  The wireless security on the network is set to a WPA compatible setting. That is because the older Express has difficulty joining 3rd party wireless networks using WPA2 Personal or WPA2-PSK-AES encryption. In other words, if your network is now using WPA2 Personal or WPA2-PSK-AES settings, the "g" Express will probably not be able to join the network.
    5)  If you are using MAC Address Filtering on your network, the MAC address of the Express will need to be included in your settings.
    6)  The wireless network password uses the same guidelines that appear in 2) above
    The items noted above will provide the Express with the best chance of joining your network.  Plan to use the Manual Setup option in AirPort Utility and be prepared to use the Option or Alt keys on the PC if needed.
    If you are looking for a guarantee of success in advance for this task, I cannot provide that and you should wait for another user to post who might be able to meet your requirements in that regard.

  • AirPort Express won't connect to existing wireless network

    I just purchased the current gen AirPort Express and it won't connect to my existing wireless network. My current wireless network is on a D-Link DIR-827 and it operates on both the 2.4 and 5.0 GHz bands. My current gen Apple TV is connected to the D-Link wirelessly and it works fine. Basically all I want to do is have a pair of speakers attached to the AIrPort Express and stream music to it via AirPlay from all my devices. When I use the AirPort Utility, I keep getting the error that 'it's setup to join an existing wireless network but it can't find it.'  The light flashes amber and I can't connect to it. Right now I've setup a new wireless network for my AirPort Express but ideally I would like to have it join my existing network so all my devices can stream to it without having to connect to it seperately.
    Thanks,
    Ata

    Hi Ata,
    ...Right now I've setup a new wireless network for my AirPort Express but ideally I would like to have it join my existing network
    If you already configured your AirPort to create a separate wireless network, it would be best to reconfigure it to "join" your existing network by starting over with a "hard reset": Press and hold the reset button and keep it depressed, continuously, about five to ten seconds, long enough for it to flash amber. Then, it will glow amber steadily for about a minute while it starts up, then it will flash amber slowly indicating it needs to be configured.
    It will then appear in your Mac's Wi-Fi menu like this:
    Select it. AirPort Utility will load and walk you through its configuration.
    Be sure to select the option to "join" your existing network, and not create a new one. In that configuration, it will serve as a device for music streaming only, and cannot serve a wireless access point. For that, your router would need to be a genuine Apple AirPort Base Station.

  • Need help connecting 5th gen Time capsule via wifi to existing wifi network(non-apple) and use ethernet out to AV receiver?

    Could anyone help advise me how to use my 5th gen time capsule airport to connect to my existing wireless modem(non-apple) over the wireless network (NOT using the WAN port with a cable) and then connect with an ethernet cable to give internet connectivity to my AV Receiver?  I would also like to be able to back up my macbook pro with the time machine/time capsule benefit.  I know that many AV setups have recommended using airport express to receive wireless connectivity to pass on internet through the ethernet port to AV setups, but I thought I would try to add the extra functionality of the over-the-air backups with the time capsule at the same time.  Is this possible without connecting with a wire to the modem which has no ability for a wired connection where the TV and AV setup is?   Any help would be much appreciated:)

    It doesn't work except to another apple router. Sorry.
    The express does work.. that is a difference between Express and Extreme/TC.

  • Time Capsule 2TB interoperability with existing home network

    Can I still use Time Machine backing up to my 2B Time capsule if it is LAN wired to a Netgear router?
    I am using my Netgear router as the primary and wireless device.  I have my TimeCapsule Wired via a lan port.  I mostly want to use the time capsule for stoarage and time machine backups.  It would also be used for media storage.  I have been told adding it as a wireless bridge is very slow. 
    Thanks in advance for any experience/advice.

    For windows.
    1. Load in the appropiate airport utility.. even if you have latest TC, and cannot configure the unit. since apple is miles behind in windows utility as neither v6 utility nor win8 have been dealt with. (or perhaps they have.. poorly!!)
    The utility includes a connection agent and bonjour for windows which helps loads.
    2. Make sure you use SMB compatbile names in the TC.. ie short, no spaces and pure alphanumeric.
    3. In windows explorer type into the address bar
    \\TCname or \\TCIPaddress where you put in the actual name or IP.
    If it doesn't respond turn off the windows firewires.. and maybe any security software you have.
    Tell me if it still doesn't work.. also what version TC are you talking about.. Gen4 or Gen5??

  • Time Capsule  as main Router for wireless network

    Hello,
    I am having issues with the speed of my internet.
    I first thought it was my internet provider. Yet when I plug directly into the TC I get the full speed I am suppose to get 6000 k/bs (checked on speedtest.net) but when I go to wireless it is down around 20 to at most 200 k/bs.
    Is there an issue with TC having this problem? I have tried setting it up as only being an N network but it still does the same thing. I have had this issue since I purchased this when it first came out. I thought it was the internet provider so had switched a couple of times then found this speed test thing and it is convincing me it is the TC.
    Suggestions? Lets see I have it set to Automatic for the channel. THe radio mode is the 802.11n, the b, & G compatible one.
    It is very frustrating.
    Sean

    Hello,
    Well thank you for the reply!
    What I did was go out and purchased a Airport Extreme "N" and hooked it up. I now get my full 6000 kb/s that I am paying my internet provider for. I AM HAPPY NOW!!!
    Sooooo this tells me either my Time Capsule is faulty or as some of the other post on this forum might suggest that it is just the router in side it.
    At any rate I am now going to give Apple Care a call or take it to a local repair Specialist (no apple store up here but authorized, MACHOUSE, do not got to the Alaska Mac Store they suck, MAC HOUSE is the place up here) and let them see the results and see what can be done.
    Sean

  • Time capsule blinking amber and my wireless network has vanished after factory reset

    Hello,
         I have an Apple Macbook aluminum body with a Motorola cable modem hooked up to the Time Capsule which acts as my router. After turning the power off in my home, the internet has not been working. The light on the TC was green, but I had no internet because Airport had a "self-assigned" IP address and may not be able to connect to the internet. Then, I decided to do a hard reset and restore my setting to factory. The light on the TC is blinking amber. When I go into Airport Utility, it gives me this message: "Airport Utility was unable to find any Airport wireless devices". On top of all this, when I did the hard reset, my wifi network is not on the list of Airport networks in my range. It has completely disappeared. I have all the wires connected properly to the router and TC. Please help, this scenario is very frustrating.

    If you performed a factory default reset, the TC is now broadcasting a wireless network with a name like Apple Network xxxxxx, where the "x" could be either a letter or number.
    You must first log on to this wireless network (there is no security or password) and establish a connection.
    Then, if the TC was reset properly, you will be able to open AirPort Utility and re-configure the TC.
    When you click Update to save your configuration settings, the TC will "dsiappear" from AirPort Utility. This is normal. Close AirPort Utility and wait for the TC to restart.
    Then log on to the "new" wireless network that you named during the configuration.

  • Airport Express won't join my existing wireless network...

    I have Broadband in my house. I have a wireless modem also. I have spent hours trying to have Airport Express join the network so I can use the music streaming feature, but I have so far not been successful. I have seen a lot of references to it being very easy and straightforward to set up with it doing most of the work itself. As in, plug in AE to a power socket, open Airport Utility and follow the instructions... It doesn't appear to be that simple, not by a long shot. Can anyone outline how this can be done in simple steps? All of the online steps I have tried do not work, with many of them referencing aspects of the Airport Utility GUI that don't seem to exist...
    Any help would be greatly appreciated.
    For the record, I DO NOT want to replace my existing wireless router, i just want AE to join the network...
    Thanks...
    Ronan

    I have the same problem - the AE wont join my Draytek 2600 wireless network. I can stream music wired, but it refuses to join the wireless network. I have tried WEP, WPA, WPA 2 etc. Always get amber flashing light. Ive spent about 5 hours solid on it so far, and I'm a networking expert.
    No other device on the planet has problems connecting to my wireless. currently I have:
    1) Belkin wireless Skype phon (no problems)
    2) SOHO wireless IP camera (no problems)
    3) Intel Macbook pro (no problems)
    4) G4 Macbook (no problems)
    5) Dell D600 XP notebook (no problems)
    Try to connect the AE? No chance. Its just broken.
    I have tried every conceiveable manual setting on the device also.
    If I manually set the ip (outside the DHCP range, but within the subnet), subnet, DNS sever, domain etc, I get a GREEN light, but nothing can communicate with it. The utility cant see it, and itunes cant see it.
    The real problem is there is no way to know if the problem is with DHCP or the wireless. Does green light mean it has a wireless connection, or it has a valid IP?
    Interestingly, if I start it with a wired connection, get a green light, then stream music to it, then pull out the wire, the green light stays, and music players for about another minute (presumably wirelessly, but who knows?) before the music stops and the device (replete with green light), becomes dead to the network.
    APPLE desperately needs to sort this out. Its junk.

  • Time Capsule Disconnects OTHER devices on wireless network during backup?

    Hi everyone,
    I need help here. I have a 500gb TC as my wireless base station as well as my backup for a new-ish 2.8 iMac. I have 2 laptops on the network as well as 2 airport express stations that just serve speakers. The house is a small 1-floor 3-bedroom.
    Every time my iMac does a time machine backup (which is often), the airport express bricks lose their music streams, and the laptops (a original Macbook Pro and a previous gen. MacBook) lose their internet and network connection - BUT they still show full signal strength and show that they are connected to the network.
    The only thing that seems to "solve" it is for me to turn my computer airport off then back on and wait for it to re-join the network.
    I have tried resetting my Time capsule - which only resulted in a VERY slow initial backup which took over 2 days to back up 200gb worth of data and then back to the same problem.
    I have the TC set up as a mixed n/b/g network, and I have one express brick extending the network ('cause I thought a weak signal might be the problem but it appears not), and the other brick joining the network. All firmware/ software is up to date. Any help is appreciated!
    Many thanks,
    jb

    jwbeaton,
    While it doesn't directly relate to your connectivity issue, might I suggest not storing other files on the TC. Use and external disk attached to the TC via USB.
    *Using a Time Machine Hard Disk (or Time Capsule) for Other Files*
    Here is Apples’ line on this: “Time Machine works best if you use your backup disk only for Time Machine backups. If you keep files on your backup disk, Time Machine won’t back up those files, and the space available for Time Machine backups will be reduced.” [http://docs.info.apple.com/article.html?path=Mac/10.5/en/11430.html]
    This hasn't stopped some from successfully partitioning Time Machine hard disks and storing data on the other partition. As long as the Time Machine backup has its' own partition, you avoid any potential opportunities for conflict.
    However, this is not an option for Time Capsule users as there is no easy way of partitioning the Time Capsules’ internal hard disk without elaborate effort. Granted, the Time Capsule is advertised as being able to perform both as a Time Machine backup destination and as a shared network drive [Apple Store (U.S.) - Time Capsule - 500 GB]
    Nevertheless, some have experienced problems with maintaining files/folders occupying the same disk as Time Machine backups. In this case, they use the Time Capsule hard disk solely for Time Machine backups. Then attach an external hard disk to the Time Capsules USB port and store additional files there. This added disk will still be available to all Macs that can access the Time Capsule. (Note though, that any USB disks attached to the USB port of the Time Capsule can not then be backed up to the Time Capsule via Time Machine. Time Machine will only backup your Macs internal hard disk or any external hard disks physically attached to the Mac. Time Machine can not backup one remote device to another remote device.)
    Hope this is helpful.
    Cheers!

  • Wireless HP Laserjet P1102w cannot 'see' my WiFi/Wireless network

    Hi all,
    I've been having some problems with my new HO Laserjet P1102w finding my WiFi network which is a Belkin N Wireless Modem/Router (PM01527ea/F5D8636-4).
    Have followed the skimpy supplied instructions, which simply say to remove all the packaging, install the Toner cartridge, connect directly to my laptop & follow the instructions which appear when the enclosed CD is inserted.
    All goes ok until it tries to connect to my WiFi Modem/Router. It correctly picks up the SSID & also manages to somehow obtain my WPA2-Personal key/pass-phrase (which is scary as I thought it secure!).
    But then nothing. Any further progress fails to connect. Even the hallowed 'HP Print and Scan Doctor' util that i downloaded fails to see the WiFi, but the windows laptop & Apple iPads/iPhones can all see, connect & operate correctly.
    Should I turn all the security off & try in plain text?
    Any help or assistance would be greatly appreciated.
    Ta,
    Simon Bond in the UK.

    Hi simonbond,
    I understand the mobile devices will connect to the printer but the computer won't.
    Thank you for your reply.
    I will be happy to help you with this.
    Print out a configuration report and make sure the SSID and IP address are correct.
    (hold down the x button and when the printer makes a noise let go)
    If you have a valid IP address for the printer then try and access the embedded web server for the printer. Type the IP address into internet explorer address bar.
    If it loads the printer's network page then the printer is on the network.
    If it doesn't load then check the network name the computer is connected to.
    Temporarily turn off any Antivirus sotware.
    Power cycle the computer, printer and router.
    Install the printer as a USB connection.
    Then go to start, all programs, HP, Laserjet, wireless configuration wizard, follow the
    steps to setup the wireless. Disconnect the USB when completed. Try printing now.
    Hope this helps.
    Thank you for posting on the HP Forums. Have a great day!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

Maybe you are looking for