AirPort Utility 6.3.2 doesn't see older AirPort Base Station

I have an old AirPort Base Station (2001 model, Dual Ethernet, "Snow", actually not "Graphite", though apparently that's the correct category here), which was previously configured with my MacBook Pro running MAC OS X 10.6.8. I've just started it up, with the DSL modem connected to it, and I'm able to connect to it (and get Internet) from my new MacBook Pro running 10.9.4 just fine. However, the latest AirPort Utility v.6.3.2 doesn't see it, says "No configured AirPort base stations have been found. AirPort Utility will continue searching." – although its window does show a green button next to the word Internet, showing (I assume) that there's an Internet connection. Does anybody know how to configure an old APBS like this from 10.9.4? AirPort Utility v.5.6.1 apparently can't be used with 10.9; is there a version that can, and will see this older AirPort Base Station?

Does anybody know how to configure an old APBS like this from 10.9.4?
Not in any way that Apple would support, or that we could discuss on this forum.
Not recommending that you try a solution from the Internet using an "unknown" author to "override" security settings on your Mac, but that would be the only way to possibly get AirPort Utility 5.6.1 to run on 10.9.4.

Similar Messages

Internet works fine, but can't see Airport Base Station w/ Airport Utility

I'm running Windows XP Pro on a Dell Latitude laptop with linksys wireless-n PCMCIA card. I have a Cable Modem running to a Linksys router (cloning a MAC address), running to the Airport Extreme Base Station. Internet works fine (as I type this), but Airport Utility cannot see the Airport Base Station. This has happened repeatedly after hard reset and re-configuration of Airport Extreme Base Station.
Do I have a bad piece of hardware?

After doing a lot of research, this appears to be a pretty common problem for Windows users.
The only thing that has worked for me is to go into the Airport Utility, and under the file menu, click on configure other. Then enter the LAN IP address of your airport extreme. I think the default is 10.0.1.1, although I have a separate router between my cable modem and my airport express providing IP addresses, so mine was different. It didn't always work at first, but now almost every time my base station disappears, if I do this it can be found again.

AirPort Utility not detecting Airport Base Station nor Airport Express

Earlier today, we were listening to music on multiple speakers (computer and airtunes / airport express) as we always do. Nothing new here. Stereo speakers stopped and computer lost connection with Airport Express. Couldn't get it to reconnect. Unplugged airport express and plugged it back in - no dice. Hard restart.....AirPort Utility detected it once and I tried to reconfigure. Got an error message at the end of configuration.....
Now.....
Airport Utility doesn't even pick up the Airport Express. Not only that, it doesn't pick up the Airport base station, which we use for our internet connection (and I'm using right now). Both are old - Airport base station is the round small anthill looking one (probably about 6 or 7 years old) and airport express is about 5 years old. Never had a problem with either. Airport Utility is 5.4.2.
For now, Airport base station is working, but I don't have access to it via Airport Utility. Airport express just flashes amber......

Welcome to the discussions!
Not sure what to suggest that you may have not already tried. I would recommend that you start with the base station first to see if you can access the settings in AirPort Utility.
Have you tried connecting an ethernet cable from your computer directly to one of the LAN ports on your base station to see if that will help? Power down your base station and computer before you hook up the ethernet cable. If no luck at first, leave the ethernet cable connected as sometimes the base station will simply "appear" after a few minutes.
If still no luck after several tries, your only alternative is to hard reset the router back to factory defaults and try to reconfigure it.
Once you get the base station back, you can use the same procedure on the Express to see if you can reconfigure it.

"No configured AirPort base stations have been found." I can see the content of the TimeCapsule's drive in finder and Time Machine but it no longer is making backups. Ideas?

Bought new TimeCapsule March 2013. Worked fine. Now get "No configured AirPort base stations have been found." I can see the content of the TimeCapsule's drive in finder and Time Machine but it no longer is making backups. Ideas?

Make sure that you have AirPort Utility 6.3.1 installed on your Mac.
AirPort Utility 6.3.1 for Mac - Support - Apple
Then, power off the entire network...all devices...in any order that you want
Wait a minute, then start the modem first and let it run a full minute
Start the next device connected to the modem, which may be your Time Capsule and let it run a minute
Keep starting devices one at a time the same way until the entire network is back up
See if AirPort Utility can "see" the Time Capsule now.
If yes, try another backup. If you encounter an error message, post back with the exact message.

My Airport Base Station does not appear in the Airport Admin Utility

I cannot see my airport extreme base station in the Airport Admin Utility nor in Airport Setup Assistant via Airport. It worked yesterday but when I was trying to set up a network something must have changed but I don't know what it is. (The setup didn't work so I am only using one base station right now.) The only way I can configure/reconfigure the base station is by physically connecting via an ethernet cable. Then no problem. I have two computers and neither can access the base station with Airport Admin Utility via Airport. I have installed the latest Airport Update but nothing has changed. What happened?

You should be able to use the second Airport Extreme
Base Station as a wireless print server. What I
suggest you do is:
1. run the Airport Admin Utility and clean up
settings on your existing Base Station:
- under the Airport tab, make sure you have not
selected to "create a closed network"
- under the Access Control tab, clear out all
settings
- under the WDS tab, clear out all settings
- under the Network tab, make sure the box is checked
to "Distribute IP addresses" and "Share a single IP
address using DHCP and NAT".
- update settings to the Base Station if you changed
anything.
2. do a hard reset of your second base station per:
http://docs.info.apple.com/article.html?artnum=107451
3. for now, put both base stations and the Mac in the
same room. Run the Airport Setup Assistant, and use
its guidance to configure the second base station as
a new base station that "extends" the wireless
network of your main base station.
That should do it.
Thanks very much. The printer works great from both computers via my second airport base station. And I can see both my base stations in the Airport Admin Utility.

"AirPort Utility unable to find any AirPort base stations"

I am getting it, along with a blanked out options panel even as I am using the two AirPort base stations and the Airport Extreme that are installed in my house. This confuses me.
I get it on my 12" Powerbook with 10.5.2 installed, but not on the one that's still running Panther. I do not get it on the iMac running Panther.
So does anybody have any idea why my "updated" PB can't see the network it's using? I have had Bonjour and Rendezvous issues in 10.5.2, too, so I am guessing these are all related somehow.
I have not installed the most recent AirPort Utility because I am afraid it will throw me offline altogether. (Should I?)
All advice welcome.

I have the same problem. Two newer macbooks work just fine but an older powerbook that was running fine on the airport extreme now say no airport card installed. Any ideas for a fix?

Lost connection to one of my Airport express units. Serial number 44500WQV0. Message in Airport Utility is to use Version 5.6 to configure base station. I have version 6.3.1. Both airport express units bought at same time few years ago.

Hello all.
Lost my connection to one of two airport express units. Both purchased few years ago. Use them to stream music to house speakers via WiFi. I have v6.3.1 of Airport Utility. Message says to use v5.6 to reconfigure this base station.
How do I do that, please?
Mahesh

You can use the following workaround to install AirPort Utility 5.6 on a Lion or Mountain Lion Mac:
Be sure to read the caveats at the end.
Lion / Mountain Lion's package installer will refuse to install superseded versions of AirPort Utility. Instead you will need to use a package extractor such as Pacifist or unpkg. Pacifist is shareware, unpkg is free.
Download Pacifist here: http://www.charlessoft.com/
Download unpkg here: http://www.timdoug.com/unpkg/
Download AirPort Utility 5.6 here: http://support.apple.com/kb/DL1482
When the AirPort Utility .dmg file finishes downloading, open it to expand and reveal the AirPortUtility56.pkg package installer file.
Directions for Pacifist (I do not have screenshots for unpkg but the idea is similar):
Open Pacifist and from its File menu, navigate to the package and open it.
Click the "reveal triangles" until you see AirPort Utility 5.6.app:
Select it and then click Install from Pacifist's toolbar. It will then be installed in your Utilities folder, and you can quit Pacifist.
The most recent version of AirPort Utility included with Mountain Lion should be used to configure 802.11n - capable AirPort Base Stations. Make no attempt to delete it. It and the older version (which will bear the unique name "AirPort Utility 5.6") can peacefully coexist. Use the older version only as necessary for older AirPort Base Stations that cannot be administered any other way.
If you happen to have an archived copy of the AU 5.6 app somewhere, such as a Time Machine backup or equivalent, you can simply restore it or drag the app to your Mountain Lion system's Utilities folder instead of resorting to the above procedure. It will run without complaint. It is only the package installer that is the problem.
Keep in mind that Apple's decision to abandon support for the original AirPort Express and AEBS was for reasons known only to them. Remember that you are using obsolete equipment, should some future OS X feature not work for you.

HT1178 No config Airport base station in airport utility

Having problems configuring Airport Time Capsule. AirPort Utility displaying No configured AirPort base stations found.
Worked initially but no longer backing up.

Try just a simple restart of the TC or restart of the network.. in order .. modem.. wait 2min.. TC.. wait 2min . then the client computer.. see if the TC reappears. if not you will need to do a hard or factory reset and start over. It is common enough on Mavericks to lose its marbles.. a good reboot will usually remind of it of where everything is.
Make sure ipv6 is set to link-local for whatever network client is being used.. that means setup in the computer.
And I do recommend using short names on the TC.. not apple names..
Keep names to <20characters.. <10 even better.
No spaces.. and pure alphanumeric.

Need a better Airport Base station admin utility

Is there a better Airport base station management utility out there we (network admins) can use to manage our 40+ airport hubs? While it is cute and nice for 1 or 2 base stations, the current util (Airport Utility.app 5.2.2) is lacking in lots of useful features:
- would like to see more than 5 devices in the left list, get rid of those over sized icons or let us make them smaller
- would like to be able to resize the window (why is ANY software made where the windows can not be resized, especially windows that show information that is bigger than the window.)
- would like to be able to select multiple base stations to get data
- would like for the list to show me all my devices and not just the devices it can detect (like ARD where I build a list)

I have been having this same issue since my purchase in January. The latest call to Applecare suggested taking the ATV out of the cabinet that it is in that also houses the receiver, and changing the channel on the setup of my Airport Extreme to channel 3. This seems to have worked for the last 3 days. I'll keep you posted.

HT1947 Airport base station doesn't let iPad make changes

Airport utility doest seem to work with my ipad
Airport base station doesn't let iPad make changes

Sky the problem.

Trying to set up a wireless guest network using Airport base station. The first network setup was fine but the second one doesn't work. Any suggestions?

I purchased the new Airport base station that allows for a wireless setup of a primary network and a guest network. The primary network installation worked great but I cannot get the guest network to work properly. Any suggestions on how to make it work?

The AirPort base station is designed to connect to a simple modem......not a modem/router or gateway device that is often furnished to users by Internet Service Providers.
So, the first troubleshooting question would be to find out what the make and model of the device that you call your "modem" might be.....to see if you have the right kind of product that will allow the Guest Network to operate correctly.

HT1331 I have windows xp. I 'm trying to download the airPort utility. how can I do this? It is required for AirPort base station right?

I have windows xp. I 'm trying to download the airPort utility. how can I do this? It is required for AirPort base station right?

Downloading the right file for XP? Check to make sure that you are running XP SP3.
AirPort Utility 5.5.3 for Windows
AirPort Utility is required if you need to set up or change the settings on an Apple AirPort router. It is not required if you are simply connecting to the wireless network from a PC.

How to make sure I'm the only one who can manage my airport base station using airport utility?

I know we have to use the Airport Utility application to manage the Airport base station in order to create a new network, creating the SSID and chosing the encryption mode and setting the password but how I could be sure I'm the only one who have access to those settings? A user of my network can install the Airport Utility application and change those settings. With other routers like D-Link, to have access to the settings you need to know the admin password to modify the settings. I can't figure out how we can do this with Airport Extreme base station. It's maybe obvious but I'm in the cloud for the moment.

You can set a base station administrator password in order to limit who can administer the base station. With AirPort Utility v6.x, you can set this password on the Base Station tab.

Airport utility can't find my airport base station

Im trying to set up a wireless internet at home. I have a comcast cable internet connected to motorola sb120 cable modem and I connected an ethernet cable from the modem to my aiport base station. when I open the airport utility in my macbook (also from my iphone 4s) the airport utility can't find the base station. the base station has a solid green ligh on and the modem "llink" light is binking amber. If I connect the ethernet cable frm the modem to my macbook I can get the internet with out any problem ...please help me set up my wireless internet with airport base station. ty.

Suggest that you try the following:
1) Reset the cable modem. There is a reset button on the back or bottom of the device. Check your documentation for the modem for exact details. In general, you press the reset button for a few seconds and then power down the modem completely.
That means pulling the power plug from the back of the modem or the AC wall plug
Leave the modem powered off at least 30 minutes
2) Perform a Factory Default Reset on the AirPort Extreme using the instructions in this document
Resetting an AirPort Base Station or Time Capsule FAQ
3) Then power off the AirPort Extreme
After 30 minutes.....
4) Connect the Ethernet cable from the cable modem to the WAN port (circle icon) on the AirPort Extreme
5) Temporarily, connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Extreme
7) Power up the modem and let it run for 5 minutes by itself
8) Power up the AirPort Extreme the same way
At this point, the AirPort Extreme should be slowly blinking amber
9) Open AirPort Utility (I assume that you have AirPort Utility 6.0) and click on Other Base Stations, then click on the Base Station xxxxxxx representing your AirPort Extreme to start the setup process
AirPort Utility should suggest that you configure the AirPort Extreme to "Create a wireless network". Accept that option and enter the required wireless network name that you want and passwords
Follow any more prompts as required and AirPort Utility should configure the device for you
Wait 25-30 seconds for a green light
10) Disconnect the temporary Ethernet cable from your Mac to the AirPort Extreme
11) Log on to the wireless network that you named during the setup process
12) Report on your results

My airport utility can't find my airport base station

My AirPort Express stopped working! It keeps flashing the amber status light. I tried finding the problem with airport utility but airport utility can no longer find my airport base station. I did a hard reset but I am not sure what to do now.????

Suggest that you try the following:
1) Reset the cable modem. There is a reset button on the back or bottom of the device. Check your documentation for the modem for exact details. In general, you press the reset button for a few seconds and then power down the modem completely.
That means pulling the power plug from the back of the modem or the AC wall plug
Leave the modem powered off at least 30 minutes
2) Perform a Factory Default Reset on the AirPort Extreme using the instructions in this document
Resetting an AirPort Base Station or Time Capsule FAQ
3) Then power off the AirPort Extreme
After 30 minutes.....
4) Connect the Ethernet cable from the cable modem to the WAN port (circle icon) on the AirPort Extreme
5) Temporarily, connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Extreme
7) Power up the modem and let it run for 5 minutes by itself
8) Power up the AirPort Extreme the same way
At this point, the AirPort Extreme should be slowly blinking amber
9) Open AirPort Utility (I assume that you have AirPort Utility 6.0) and click on Other Base Stations, then click on the Base Station xxxxxxx representing your AirPort Extreme to start the setup process
AirPort Utility should suggest that you configure the AirPort Extreme to "Create a wireless network". Accept that option and enter the required wireless network name that you want and passwords
Follow any more prompts as required and AirPort Utility should configure the device for you
Wait 25-30 seconds for a green light
10) Disconnect the temporary Ethernet cable from your Mac to the AirPort Extreme
11) Log on to the wireless network that you named during the setup process
12) Report on your results

AirPort Utility 6.3.2 doesn't see older AirPort Base Station

Similar Messages

Maybe you are looking for