Airport utility base station indicator conflict
After upgrading firmware to 7.6, I'm having an odd issue with the Airport Utility. I have a dual base-station setup, connected together via twisted pair so that the second unit is in bridge mode. It has been working well for over a year.
From the enclosed picture, you can see that the summary shows amber for both base stations, but when I bring up details, everything is green. The network is working fine. Also, the IOS Airport Utility reports everything is fine.
This did not happen before the firmware upgrade - back then everything was green.
Any ideas?
It is always a good idea to power cycle the entire network after any firmware update to any of the AirPort devices.
Try the following:
Power everything down on the network....all devices....order is not important
Wait a few minutes
Power up the modem first and let it run for a minute
Power up the next device connected to the modem the same way
Keep powering up devices the same way until everything is back up
Check the network again using AirPort Utility
Similar Messages
-
I am connected to an airport utility base station I don't recognize
I don't understand much about the technicalities of how internet connections work, but today I was working on my macbook as usual and I noticed a message from airport utility telling me I was connected to an Airport Express device from a "Josh". I have no idea what that means. I tried to find out more about this base station, but it asks for a password I don't have, so I can't seem to disconnect. Does anyone knows what that means? Btw, I live in student's building so we have shared connection via ethernet. I've been searching on google for a while now and found nothing to explain.... help, pls? thanks!
I hate to have to tell you this, but backing-up that way is unreliable and not supported by Apple. See: Using Time Machine with an Airport Extreme Air Disk.
-
Airport Utility Base station password
Hello
I have the Airport Extreme router and I have also installed the Airport Utility programme on my win7 machines for convenience.
The win7 wireless machines including the Apple macbook always prompts for a password ( As I set-up Airport Utility to work this way ) but whenever I open the Airport utility which I have installed on the wired Ethernet desktop win7 machines, the Airport Utility never prompts for a password.
My question is can I force the Airport Utility on the desktop machines to prompt for a password ?
When I open the base station and select manual setup, then under base station I have un-ticked remember password in my keychain and then updated this, but whenever I reopen the Airport Utility the tick reappears and the Airport Utility opens without prompting for a password.
I must again stress that the wireless machines always prompt for the password.
ThanksYour desktop machine has already stored the Base Station password, so unchecking the box that tells the PC not to remember the password that it has already stored is not going to work.
I don't know where Windows keeps stored passwords, but if you do, you will need to access that file and delete the Base Station password there.
If you don't know how to locate the stored password file on the PC to erase the password, then the simplest thing to do might be to set up a new Base Station password, and make sure that the box next to "Remember password, etc" is not checked when you click to Update the new settings in AirPort Utility. -
Airport Extreme Base Station and DSL modem, IP address Conflict issues
I recently set up DSL service in my apartment. I have ATT yahoo DSL modem, and an Airport extreme base station plugged into it. The network works fine with my Vista PC connected to it, but when I try to connect my macbook to the network I get errors telling me the IP address the macbook wants to use is already in use, and my PC gives me an IP address conflict error.
The internet is fine, and the modem is configured automatically, so I think it must be a problem with the way the network is set up or the network settings on my macbook...
any ideas?All,
I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes? -
Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?
Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
Power off the AirPort by pulling the power cord
Wait a minute or two
Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
Release the reset button and allow a full minute for the AirPort to restart
Now try to configure the AirPort again. If you continue to see the same symptoms as before, the AirPort will need to be replaced. -
I am currently running a PowerPC G5 imac and have a wired broadband modem via ethernet with airport wireless network turned on, on the G5. I have the computer in the bedroom and have an airport express wired into a mixer that connects to my stereo. I have recently bought another airport express base station to connect to a pair of active monitors in the kitchen. When I try to scan these on Airport Utility version 5.42 I am only managing to scan one base unit at a time. I have plugged them in separately and reset them, they both have firmware updates, however the utility will only read one at once. I have read that you can link base stations to the same WDS. I would like to know how to go about doing this if it will only scan one airport express at a time. I have looked it up on the net and not found anything that is a simple fix. Can anyone help? In Apple Support it says that multiple Base Stations can be used. I would like to get both Apple Airport Express units to be able play airtunes separately or at the same time depending where I am in my flat. I do not need different music in each room. I would like to stream music from the computer to multiple rooms in the flat without having to continually unplug and configure the Base Stations. Has anyone come across such a challenge? Any help would be welcome.
How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX. -
Hi. In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds. Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended. I folllowed all the directions from the apple support pages, and finally got it to work. I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension. Then a week or so ago I noticed that my laptop would no longer connect to my base station. I did not have time to look into it until this week. Airport utility, either on my Mac or iphone no longer recognizes my base station. My mac is running OS X 10.10.1 and my iPhone is running iOS 8.1.2 I have tried both hard, soft and factory resets of my base station to no avail. The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before. I can't actually connect to it, but it does try. Then after approximately 5 minutes, it disappears from my list.
Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c? airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software. I am attaching an image of that.
Thank you,
John
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature. -
I can no longer access my Airport Express Base Station. When I plug it in, it keeps flashing orange. I cannot see it in the Airport Utility.
How do I fix thisIf you're comfortable resetting all settings, unplug it, hold down the reset button and keep holding it in as you plug it back in - keep holding it for another 10-20s until the amber light flashes
Then, open airport utility, now you should be able to see the device either on-screen or in the upper left under 'other wi-fi devices' -
Airport Utility can no longer see my Airport Express Base Station.
Hi all the problem I have is as follows;
I've set up my Airport Express Base Station some time ago to print wirelessly from my HP Photosmart C4280 and it was working fine.
However recently when I've gone to print a document, even though the printer is working fine and the Airport Express Base Station is showing a green light nothing happens. I've gone into the Airport Utility and its say's it can't see the Airport Express Base Station (even though it still has a green light showing). If I unplug the Airport Express and plug it in again, the Airport Utility can suddenly see it again.
I've successfully gone through the reset process but after a few minutes the Airport Utility can no longer see the Airport Express Base Station which means I can't print a document wirelessly. I've repeated the reset process several times with the same outcome.
Everything was working fine up until recently, has the Airport Express Base Station developed a fault? or is there something I'm not doing.
Any advice would be greatly appreciated.If you're comfortable resetting all settings, unplug it, hold down the reset button and keep holding it in as you plug it back in - keep holding it for another 10-20s until the amber light flashes
Then, open airport utility, now you should be able to see the device either on-screen or in the upper left under 'other wi-fi devices' -
After downloading firmware for airport utility last night, airport express base station was deleted from airport utility and only Time Capsule remains. When I plug in the base station, an amber light blinks without being able to verify the cause. Any suggestions to remedy this problem?
There are only a couple of things you can do to resuscitate a nonresponsive Express:
"Hard reset":
Press and hold the reset button with a pen or pencil until you see the status light (LED) start to flash amber rapidly, which should occur after about five seconds.
If that does not work,
"Factory defaults reset":
Unplug the Express from power.
Press and hold the reset button with a pen or pencil, then plug the Express back in while continuing to hold the button until you see the light (LED) flash rapidly. This should happen after a few seconds.
Release the button.
In either case you will have to reconfigure the Express as a new device. A moment or two after it has been reset, the LED should be blinking slowly. It must then appear in your Wi-Fi menu like this:
Earlier versions of OS X will report it as "Apple Network nnnnnn".
In either case, select it, and then launch AirPort Utility.
If it does no appear in your Wi-Fi menu after it has been reset using one of the two techniques above, it is defective. Other than attempting another reset, there is nothing you can do. -
I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?
apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together. -
Why won't the Airport Utility recognize my Airport Express Base Station
I have an Airport Express Base Station I had recieved from a friend of mine. It is a 802.11n Wi-Fi Station, and I'm running OSX 10.7.4. When I open airport utility 6.0 it can't find my devie and the same with Airport Utility 5.6. I've tried resetting the station and plugging it directly into the computer via ethernet cable but nothing has happened. Someone help?!
Nevermind, I figured this one out. Just perform a hard reset. Unplug the base station, push and hold the reset button then plug the station back in while still holding the button in. Continue holding till the the LED flashes yellow really fast. Release and wait till the Airport Express starts up.
-
Airport Utility 5.4.2 was unable to find Airport Extreme base station.
I downloaded the new Airport Utility 5.4.2 to my 2009 24" iMac with Snow Leopard. Now it is unable to find my Airport Extreme base station or Airport Express. My iMac is connected to the network via the Airport Extreme base station but the Airport Utility cannot find it. All I get is this message "Airport Utility was unable to find any Apply wireless devices. Make sure the Apple wireless device you want to set up is plugged in and in range of your computer and then click rescan to try again". I clicked rescan numerous time with no luck. I even downloaded the Airport Utility 5.4.2 again with no luck. What is wrong??? Everything was working fine until I downloaded the Airport Utility 5.4.2.
Thanks for the info.
Following your same steps exactly, I am able to save the configuration file to the desktop, or navigate to another folder to save it at that location.
I was able to do this previously with 10.5.x and with current Snow Leopard. Notice that you list 10.4.x as your operating system. If you are still running this OS, it could be that 10.4.x does not allow this feature with 5.4.2?
Not sure if downloading another copy of 5.4.2 would be worth the pain, as I'm inclined to believe that it probably would not help solve your issue. If you decide to do this, please post back with your results. -
Airport Utility cant connect to Airport Extreme Base Station, Error code -4
I am unable to use my Apple-product. Earlier it worked, with these settings: The Airport Extreme Base Station worked as a Gigabit switch and an Access Point. It was not supposed to work as a router, since I have a server "on the far side" of the AEBS.
In any case, it worked for a while. Then it started to act strangely, so I tried to check its settings. I was unable, so I did a factory reset. And haven´t been able to connect (for configuring) since. (It still works as a router and access point, but with the default settings, and with a blinking yellow led.)
When I use the Airport Utility (5.5.1) connected with a cable it finds nothing. Should I be able to configure it wired? When I connect wireless to the default "Apple Network XXXXXX" it finds the Airport Extreme "with default settings". I click "continue" or "Manual setting", and it says "Detecting wireless Apple Devices" (bear in mind that I translate the messages from swedish, It might get wrong), and then after a minute:
An error occurred while trying to access the base station. Make sure your network connection is valid and try again. Error Code: -4
I have shut off the firewall in both Windows and Panda Cloud Office Protection. I have tried to make lots of factory resets.See this article for instructions on how to install AirPort Utility 5.6 for Lion on Mountain Lion:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html -
I have an old airport express base station from 2005
I would like to have a network on it so i can put it upstairs in a room and connect my speakers to it so i can send my music (from itunes) over the airport to my speakers.
I reset it and now i want to configure but the Airport utility doesn't recognise it anymore.
Can i update the firmware? has it become useless because too old or what can i do?
I work on macbook pro with macOSX 10.9.4
Can someone give me some tips please
thanks
JPlease locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.
Maybe you are looking for
-
Unable to use WFDDisplaySinkStart API in a Windows 8.1 Desktop application project.
Does anyone know where the following files are located within the SDK? Header: Wfdsink.h Library: Wifidisplay.lib Thanks!
-
everything in post
-
Search Results Not Highlighted
After a recent update Acrobat 9 Standard 9.4.5 does not highlight search ruseults. Is anybody else having this problem? Is there a setting I can change?
-
Question about battery maintenance and longevity
I have a question about the efficacy of the built-in battery maintenance of the Lenovo Power Manager utility; specifically how it pertains to my W520, if that makes any difference. With my previous laptop (an HP), any time I knew it would be parked o
-
Hello! I have an old A55 (9641) Which I want to update a little bit. I added some more RAM and installed the latest BIOS from the Lenovo support website . I want to upgrade from the original Core 2 Duo E4300 (1.8GHz) to a Core 2 Duo E4700 (2.6GHz). I