AirPort Utility can't detect base station but my laptop's wireless utility

Just bought an AirPort Extreme base station yesterday. I have installed the new version of AirPort Utility from the disk on my Windows XP laptop and updated it online.
Visibility of the station from AirPort utility is very sporadic. I have gone through setup twice and done a re-set of the station once. I can see the station from my laptop's wireless utility, but can't establish an internet connection. Can't connect with AirPort Utility long enough to figure out if the configuration is ok.
Anyone seen anything like this? Could I have a bad base station? thanks.

I have a similar problem, only it is my MacBook that can see the Airports, and my G5 that cannot. To make it even more counter-intuitive, the G5 is *plugged in* to the Airport Extreme base station, and while it gets internet and other network devices, it cannot talk to the very router it is connected to.

Similar Messages

  • HT1998 How can I administer a Gen 1 Airport Express from Airport Utility 6.3.2 (OS 10.9). I can see the base station but get the message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more inform

    How can I administer a Gen1 Airport Express from, my MacPro (OS 10.9, Airport Utility 6.3.2). I can see the Express in the WiFi window but from the Airport Utility I get the following message: " This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Of course there's nothing of value on the support page. Any clues anyone?

    Apple has dropped support in Mavericks (10.9) of the AirPort Express and AirPort Extreme models that were discontinued more than six years ago.
    You can still administer the older AirPort models if you have a Mac running Leopard, Snow Leopard, or a PC.

  • Airport Utility can't find base station, but station works fine

    I recently purchased an AEBS. The network seems to be working fine (I have an iMac flat panel (10.3) connected via Ethernet, an iBook (10.3) connecting wirelessly, and a Mac mini with 10.4 connected wirelessly). However, airport utility doesn't see the base station. Should I be concerned?

    Got my answer from previous posts -- had to do a hard reset *while the device was plugged in and wait for the flashing green light* then it all worked fine. thanks !

  • Airport Express Can't See Base Station

    I have an airport extreme base station that has two computers normally connected to my network wirelessly (iMac G4 and Powerbook G4) which have worked fine for months. After completing an apple security update this evening on both computers the Powerbook G4 did not automatically connect to the network upon restart as it normally does. The iMac G4 started up fine and is how I am posting this note. The powerbook on the toolbar shows the network I want to join but when I select it (and and see the check mark next to it) I still cannot access the internet. When I run the Airport admin utility it cannot see any base stations (despite the iMac sitting 1 foot away and working perfectly). When I manually give it the IP address and password it says "unable to read the configuation of the selected base station." When I try the Airport Setup Assistant it also lists my network as one that I can choose but when I click on the "continue" button it says "unable to establish a network connection" and that my computer could not connect to the internet. Help!!! I have tried every angle I can thing of to get the Powerbook to connect like it did a few hours ago.

    I have just discovered the same problem. After downloading the latest security update my Powerbook G4 [10.3.9] can not "see" any base station or express and/or connect to my network. The G5 running 10.4.5 works fine and sees all. Everything had been working just fine before the update then... Have tried all the work arounds I can think of and wasted a great deal of time. Any answers out there?
    G5Tower / G4Powerbook   Mac OS X (10.4.5)   G4Powerbook OS 10.3.9

  • Airport express-can't find base station

    I've tried everything I can think of-I've reset my ae several times and still utility is not finding the base station-help!

    I am having the exact same thing. I saw it once, and made some setting changes, now it's gone. I bought the bloody thing because although my modem has Upnp the mac claimed it wasn't working, so I though ok (back to my mac - only been trying to get it running for about a year: zero success) I'll get a base station, that supports NAT for BTMM, but the one time I did access the base station its error was double NAT, so the mac and the base station seem to be reporting two different things regarding the modem. It is driving me ballistic!!!!

  • Can connect to base station but cannot browse the internet

    Hi,
    I have got a MacBook 2GHz Intel Core Duo with Leopard installed (10.5). I have had trouble free wireless internet access for the last 12 months using a Belkin ADSL Router.
    Just today I have lost access to the internet completely for both wireless and ethernet.
    When I look at the Network dialog for either Airport or Ethernet it says that it is connected and it has got an IP address assigned by the router within the range I would expect. When I use the diagnostic utility it says that everything is fine.
    I can browse to the admin pages of the router no problem.
    I have reset the router numerous times and also tried the reset of the Mac where you take the battery out and hold the power button down for 5 seconds.
    Nothing has worked.
    I have got a PC connected to the same router and it is connecting to the internet fine.
    Any ideas??

    Jon,
    Some other thoughts occurred to me...
    When did this start? What change, if any occurred just prior to the onset of symptoms?
    Have you recently upgraded to Leopard? Did it work after that?
    Have you tried connecting to the internet on another wireless network like an internet cafe or a friend's house?
    Does your PC, which works, rely on proxy settings to browse through?
    Lastly, you asked if your ISP could have caused this. Normally, I would say no because you are connecting to your ISP through a single point and IP address, that of your router. While many ISPs have always wanted to bill their users by the number of computers that are using their services, this has been difficult to do because of the prevalence of IP address sharing granted by the routers that are so common in our homes. It may be possible that your ISP has found a way around this but I remain skeptical.
    Sean

  • I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

    I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

    When you can, take a look at the old AirPort Express and locate the model number in the faint print on the side of the device.
    If you see A1084 or A1088, this is an older Express version that is no longer supported by the current version of AirPort Utility that you are using with the new AirPort Extreme.
    If that is the case, your Express is at least 6 years old...probably older...so it is about time to treat yourself to a new version with much faster speeds and more features.

  • Airport Utility fails to see Airport Extreme Only an Older Base Station no longer connected

    Very weird what's happened... earlier this morning there was a power failure (none of my 2 computers were ON, and they are plugged in thru UPS with power surge/outage capabilities).
    I turned my old Macbook Pro (2007) and everythign is fine. My Mac Pro (2008) is fine but it can't connect to the internet.
    I've resetted both the modem and the Airport Extreme Base Station.
    I've restarted and resetted the PRAM on my Mac Pro.
    I've tried many times to diagnose it/change settings/create new network with Network and Airport Utility to no avail.
    When I open Airport Utility on the Macbook Pro, it shows the Airport Extreme and it all looks fine... when I open Airport Utility on the Mac Pro, it only sees an old Snow/Graphite Base Station I haven't had plugged in in a log time. It doesn't see anything else.
    I've tried trashing the Airport Utility preferences as well... but still nothing. The Wif Fi icon shows a '!'. When I click on it, the pull down menu shows an "Alert: No Internet Connection", but it still shows my network  (and the neighbours' network) and it even has the check mark next to my network... ???
    I'm running 10.8.5 and Airport Utility 6.3.1.
    Please. Help.

    Just a quick update, spent 90 minutes on the phone with apple support today.  If I boot the mac in safe mode, the airport utility can see the base station.
    In the course of trouble shooting, a test account was created, but the airport utility had the same issue.  It proved that there isn't anything wrong with any of the hardware at the very least, and points to user level configuration problems (unfortunately, I was not able to sort that out with support).
    Regards,
    Seth

  • My Airport wireless is working for my two MacBook Pros and my daughter's iPod, but our iPad, Iphone and other iPod all say they need to set up an Airport Base Station but do not have the proper software.  I'm not sure what to do to remedy this situation.

    My Airport wireless is working for my two MacBook Pros and my daughter's iPod, but our iPad, Iphone and other iPod all say they need to set up an Airport Base Station but do not have the proper software.  I'm not sure what to do to remedy this situation.

    This might sound like a silly question, but are you sure the iOS devices (iPhone, iPad, iPod touch etc.) are still trying to connect to the same network from your own Airport router, as the MacBook Pros are? If you tap Settings on them, is the network name next to where it says Wi-Fi, the right one?
    I've got a weird feeling that either in the past couple of days, a neighbour got an Airport device and hasn't set it up yet (causing your iOS devices to try to help), or that perhaps there's an issue with your Airport router and they're noticing it and trying to help out, while for whatever reason, Airport Utility isn't opening itself on the MacBook Pros like it normally should if there's a problem.
    If you open Airport Utility on one of the MacBook Pros, does it report any problems with your Airport device, and can you view/edit the settings on it?

  • Utility can't find base station

    I'm trying to change the security protection on my base station but when I open the Airport Utility, it just scans for a long time and says "can't find base station." The station works fine but the utility can't find it. What should I do?

    I've had the same issue for several weeks also. Even reverting back to 7.1.1 I still have the problem. It's an issue for me, as the Airport Disk Utility doesn't recognize my USB disk.
    While restarting Aiport Extreme temporarily solves the problem, everytime I shut down my Mac, Airport Utility doesn't recognize my disk when I start up my Mac. Have you found out anything yet?

  • HT1178 Can I just use my airport express as the primary base station and the time capsule as the network client?

    I bought a new airport time capsule 3tb to be used to save to file all my pictures. Can I use it as network client and the airport express as the
    Primary base station?

    To my opinion this looks a bit like what I'm looking for.
    At the moment I have an Imac that is wireless connected to a 2TB time capsule (TC1).
    To this time capsule I have another 2TB time capsule (TC2) connected via a upt wire connection.
    At the moment there is a backup made via time machine from the Imac to the time capsule TC1 (the second TC is not used)
    I'm not so technical so I hope you understand the configuration.
    What do I want to achieve :
    copy all my data from the Imac to TC1 so that the information can be accessed by more users.
    create an automatic backup from TC1 to TC2 (mirror or raid system) for security.
    give access to some users on the network to access TC1 to read and write data.
    TC2 only serves as backup from TC1 and no direct access is needed to this disk.
    If there is a solution, thanks for explaining it in 'IT kindergarden style' so that I can understand and use the info.
    Many thanks in advance.

  • AAU for graphite and snow can't find base station

    I've always been able to find an answer on the discussion lists before, but I don't see where anyone has posted about quite this same problem:
    I have a dual-ethernet (aka snow) airport that I'm using with a new model MacBook Pro. I'm using the Airport Admin Utility for Graphite and Snow (AAU for G&S) to manage the airport, and all had been working well until the past couple of days. I was having signal problems with the MacBook Pro but not with my old ibook G3. IStumbler showed more people in my apartment building were using the channel I had set so I thought I'd switch in case that was the problem. AAU for G&S on the MacBook Pro couldn't recognize the base station but the old AAU on the G3 ibook did so I changed my channel and the signal must have improved enough for the MacBook Pro since I was then able to connect to the Internet with the MacBook. But I still couldn't find the base station with the AAU for G&S.
    I did a hard reset (or the equivalent) per support doc "Resetting the AirPort Base Station (Dual Ethernet)" and tried to reload the software per another support doc "AirPort Base Station (Dual Ethernet) : How to reload software from Mac OS X". When I hooked the MacBook Pro up to the airport by ethernet, I still couldn't find the airport in the AAU for G&S. And now after the reset, I can't see it anymore on the old utility on the G3 ibook.
    While the MacBook Pro was hooked up to the airport by ethernet, I was able to connect to the Internet that way, and I'm wirelessly connected to the airport right now (which is hooked up to my cable modem). But if I need to change my channel again or do something else to the base station, I'm stuck--the AAU for G&S can't find it.
    Is anyone else still trying to hold on to their Snow airport and either run into or solved this kind of problem? Very grateful for any assistance!

    Thanks to everyone who read my question, but I seem to have found a solution to this which only goes to show if you mess around enough ... Anyway when my AAU for G&S couldn't find the base station by scanning, I had tried using the "Other" option and entering the IP address that I saw in the Network Preferences Advanced window. That didn't work, but this morning I notice that there was another IP address, slightly different for Router. Since my Airport Snow is functioning as my router to my cable modem, I tried that IP address and voila, I can bring up the settings on my base station and reconfigure them. I've done this several times successfully so far. Of course I now may have to get rid of the old Airport since the network interference in my apartment building is now getting ridiculous, and I'm hoping the the newer Airport Extreme will help me to find a wireless space that will work consistently without dropouts.

  • Can't locate base station using Mac or windows

    I just bought a airport extreme to replace my ageing linksys. I set it up exactly per instructions. I got the light to glow green. However, none of my devices can locate the base station on airport  utility.

    If you plug the new base station in the password is "public" and you should be able to find it at 192.168.0.1. Open a broswer and type in that address and you should get a login to set it up.
    You need to plug into it direct with a cable if you can't sign in to the wireless network.
    DB

  • Can I use Base Station with Extreme Card?

    Hi,
    I was thinking of updating my iBook to a new one with an Extreme Card. I have the snow Base station that I am currently using with my G3 iBook. I know the G3 iBook with old Airport card would work on the Extreme Base Station but what about the other way around. Can I use the old Airport Card with a new Extreme Base Station? I would hate to have to spend the money on a new base station. I do understand the speed would be slightly slower than if both the base station and the card were extreme. Thanks.
    Thom

    I know the G3 iBook with old Airport card would work on the Extreme Base Station...
    Can I use the old Airport Card with a new Extreme Base Station?
    As you state in your first statement, yes a Mac using an original AirPort card can connect to an AirPort Extreme base station (AEBS).
    I do understand the speed would be slightly slower than if both the base station and the card were extreme.
    Since you will be using an 802.11b card, the speed will be the same 802.11b speed that you are getting now.

  • Adding an Airport Express to an Extreme Base Station

    I have an Airport Extreme Base Station and it has been operating for several months, I decided to add an Airport Express to extend the range and it appeared that it was a simple process. NOT. The Express instructions indicated that when downloading the software to follow the instructions on setting up a network but it will not get that far in that I get an error message telling me I have a newer version of I Tunes and it stops the install. I have gone through the tech support pages here and am at a loss on how to get this connected. Can anyone help provide me a step by step method to do this? Thanks

    On this same topic;
    We have a new Extreme base station that connects 1 MBP, (wirelessly), 1 HP Laptop (wirelessly) and 2 PC (via ethernet) to the internet.
    All of the computers can see and use the Extreme base station and the printer connected to it via USB.
    We also have an Airport Express that the two laptops can see. This has a printer connected to it as well via USB. (both are new Canon printers and all of the software for each, and their drivers are loaded on all computers).
    Both the Extreme and Express have a steady green light, their own names and are set up on the same network.
    Though my MBP can see both the Extreme and Express, neither "see" each other as far as I can tell. And, the printer connected to the Express cannot be seen in either Bonjour Printers, or anywhere else.
    Also, in order to "attempt" to find the printer connected to the Express, I have to disconnect from the Extreme Base Station and connect to the Express.
    How can I get the printer (connected to the Express) to show up in my pick list of printers WITHOUT having to disconnect from the Extreme and connect to the Express. Also, how can we get the Express to be connected to the internet via the Extreme?
    All searches here and documents I have poured though do not address this issue and we'd really like to get this straightened out. I am willing to take a lot of time to do this, but do it right.
    Can someone please help me with this?
    Thank you in advance,
    ~ J

Maybe you are looking for